The content of this thesis are relations between the Federal Republic of Germany and the GDR at the end of the Cold War, specifically in the seven-year period between the beginning of the government of Helmut Kohl and the fall of the Berlin Wall. These relations are described in a wider dimension within a square made of Bonn - Berlin - Prague - Moscow; the basic intention of the work is to create a comprehensive analysis of all important links and transformations not only between the East and West Germany, but also among all actors in defined tetragon. Thesis-conclusions are to a large extent based on the long-term research in Czech and German archives; key documents were found in the archive of the Czech Ministry of Foreign Affairs and in the archive of the former State Security of the GDR. The term inter-German relations is reduced to the area of Deutschlandpolitik - negotiations at the highest level - and given the large scope of reciprocal contacts, they are limited also thematically, while two dimensions are primarily monitored - so called priority axis. The first is the field of economy. Its key importance is framed by two billion-loans granted with a guarantee of the Federal Government of the GDR at the beginning of analysed period, and a total paradigm shift in relations among Bonn - Berlin...

Submitted by Automa??o e Estat?stica (sst@bczm.ufrn.br) on 2015-09-28T20:12:49Z No. of bitstreams: 1 RodrigoSiqueiraMartins_TESE.pdf: 3898946 bytes, checksum: 0606c73d62c01f99eaf21d5af3faf852 (MD5) / Approved for entry into archive by Elisangela Moura (lilaalves@gmail.com) on 2015-10-01T13:50:44Z (GMT) No. of bitstreams: 1 RodrigoSiqueiraMartins_TESE.pdf: 3898946 bytes, checksum: 0606c73d62c01f99eaf21d5af3faf852 (MD5) / Made available in DSpace on 2015-10-01T13:50:44Z (GMT). No. of bitstreams: 1 RodrigoSiqueiraMartins_TESE.pdf: 3898946 bytes, checksum: 0606c73d62c01f99eaf21d5af3faf852 (MD5) Previous issue date: 2014-06-27 / A detec??o e o diagn?stico de falhas, ou seja, descobrir como, onde e porque as falhas acontecem, ? uma importante ?rea de estudo desde que o homem passou a ser substitu?do pelas m?quinas. No entanto, nenhuma t?cnica estudada at? hoje consegue resolver em definitivo o problema. As diferen?as em sistemas din?micos, sejam eles lineares, n?o lineares, variantes ou invariantes no tempo, com redund?ncia f?sica ou mesmo anal?tica dificultam as pesquisas no sentido de obter uma solu??o ?nica. Neste trabalho, ser? apresentada uma t?cnica de detec??o e diagn?sticos de falhas (FDD) em sistemas din?micos utilizando observadores de estado em conjunto com outras ferramentas de maneira a criar um FDD h?brido. Um observador de estado modificado ser? utilizado para a cria??o de um res?duo que permita a detec??o e tamb?m o diagn?sticos de falhas. Um banco de assinaturas de falhas ser? criado a partir de recortes utilizando ferramentas estat?sticas e por fim uma aproxima??o usando erro m?dio quadr?tico (MSE) servir? de infer?ncia e auxiliar? no estudo do comportamento das falhas e no diagn?stico das mesmas, ainda que na presen?a de ru?dos. Essa metodologia ser? ent?o aplicada a uma planta did?tica de tanques acopladas e outra com instrumenta??o industrial com fim de validar o sistema. / The detection and diagnosis of faults, ie., find out how , where and why failures occur is an important area of study since man came to be replaced by machines. However, no technique studied to date can solve definitively the problem. Differences in dynamic systems, whether linear, nonlinear, variant or invariant in time, with physical or analytical redundancy, hamper research in order to obtain a unique solution . In this paper, a technique for fault detection and diagnosis (FDD) will be presented in dynamic systems using state observers in conjunction with other tools in order to create a hybrid FDD. A modified state observer is used to create a residue that allows also the detection and diagnosis of faults. A bank of faults signatures will be created using statistical tools and finally an approach using mean squared error ( MSE ) will assist in the study of the behavior of fault diagnosis even in the presence of noise . This methodology is then applied to an educational plant with coupled tanks and other with industrial instrumentation to validate the system.

Submitted by Automa??o e Estat?stica (sst@bczm.ufrn.br) on 2016-03-22T19:35:00Z No. of bitstreams: 1 AldayrDantasDeAraujoJunior_TESE.pdf: 6801282 bytes, checksum: 6465e3e1ed3f877f913f31049263ffc2 (MD5) / Approved for entry into archive by Arlan Eloi Leite Silva (eloihistoriador@yahoo.com.br) on 2016-03-28T19:14:32Z (GMT) No. of bitstreams: 1 AldayrDantasDeAraujoJunior_TESE.pdf: 6801282 bytes, checksum: 6465e3e1ed3f877f913f31049263ffc2 (MD5) / Made available in DSpace on 2016-03-28T19:14:32Z (GMT). No. of bitstreams: 1 AldayrDantasDeAraujoJunior_TESE.pdf: 6801282 bytes, checksum: 6465e3e1ed3f877f913f31049263ffc2 (MD5) Previous issue date: 2015-04-29 / O ?xito atingido pelos m?todos t?rmicos de recupera??o, em ?leos pesados, motivou o surgimento de estudos relacionados com a utiliza??o de ondas eletromagn?ticas como fontes geradoras de calor em reservat?rios de petr?leo. Desta maneira, essa gera??o ? obtida atrav?s de tr?s tipos de processos distintos de acordo com o intervalo de frequ?ncias utilizado. S?o eles: o aquecimento eletromagn?tico indutivo, o resistivo e o diel?trico, tamb?m conhecido como por radia??o. O presente estudo foi baseado em simula??es computacionais em reservat?rios de petr?leo com caracter?sticas similares aos encontrados nas bacias sedimentares do Nordeste brasileiro. Todos os casos estudados foram simulados usando o programa STARS, da CMG (Computer Group, Modelagem vers?o 2012.10). Algumas simula??es levaram em considera??o a inser??o de part?culas eletricamente sens?veis em determinados setores do modelo de reservat?rio estudado atrav?s de fraturas. A proposta deste trabalho ? a utiliza??o do aquecimento eletromagn?tico por indu??o como m?todo de recupera??o de ?leos pesados, para verificar a influ?ncia dessas part?culas acima citadas no modelo de reservat?rio utilizado. Foram feitas an?lises comparativas envolvendo o aquecimento eletromagn?tico indutivo, a opera??o do fraturamento hidr?ulico e a inje??o de ?gua em diferentes situa??es do modelo de reservat?rio estudado. Foi constatado que fraturando o po?o injetor com o intuito de que o aquecimento eletromagn?tico ocorra no mesmo po?o em que h? a inje??o de ?gua, houve um acr?scimo consider?vel do fator de recupera??o e produ??o acumulada de ?leo em rela??o aos modelos em que o fraturamento hidr?ulico ocorria no po?o produtor e a inje??o de ?gua no po?o injetor. Este fato se deve ? gera??o de vapor in situ no reservat?rio. / The success achieved by thermal methods of recovery, in heavy oils, prompted the emergence of studies on the use of electromagnetic waves as heat generating sources in oil reservoirs. Thus, this generation is achieved by three types of different processes according to the frequency range used. They are: the electromagnetic induction heating, the resistive and the dielectric, also known as radiation. This study was based on computer simulations in oil reservoirs with characteristics similar to those found in the sedimentary basins of the Brazilian Northeast. All cases studied were simulated using the software STARS, CMG (Computer Group, version 2012.10 Modeling). Some simulations took into account the inclusion of electrically sensitive particles in certain sectors of the reservoir model studied by fracturing. The purpose of this work is the use of the electromagnetic induction heating as a recovery method of heavy oil, to check the influence of these aforementioned particles on the reservoir model used. Comparative analyses were made involving electromagnetic induction heating, the operation of hydraulic fracturing and the injection of water to the different situations of the reservoir model studied. It was found that fracturing the injection well in order that the electromagnetic heating occurs in the same well where there is water injection, there was a considerable increase in the recovery factor and in the cumulative oil production in relation to the models in which hydraulic fracturing occurred in the production well and water injection in the injection well. This is due to the generation of steam in situ in the reservoir.

Made available in DSpace on 2014-12-17T14:55:52Z (GMT). No. of bitstreams: 1 BezalielASP_DISSERT.pdf: 2307069 bytes, checksum: aa5ddc5e2ae2722d27d66e85a1e511f1 (MD5) Previous issue date: 2011-08-03 / This work develops a methodology for defining the maximum active power being injected into predefined nodes in the studied distribution networks, considering the possibility of multiple accesses of generating units. The definition of these maximum values is obtained from an optimization study, in which further losses should not exceed those of the base case, i.e., without the presence of distributed generation. The restrictions on the loading of the branches and voltages of the system are respected. To face the problem it is proposed an algorithm, which is based on the numerical method called particle swarm optimization, applied to the study of AC conventional load flow and optimal load flow for maximizing the penetration of distributed generation. Alternatively, the Newton-Raphson method was incorporated to resolution of the load flow. The computer program is performed with the SCILAB software. The proposed algorithm is tested with the data from the IEEE network with 14 nodes and from another network, this one from the Rio Grande do Norte State, at a high voltage (69 kV), with 25 nodes. The algorithm defines allowed values of nominal active power of distributed generation, in percentage terms relative to the demand of the network, from reference values / Neste trabalho, prop?e-se uma metodologia para defini??o dos valores m?ximos de pot?ncia ativa a serem injetados em barras pr?-definidas das redes de distribui??o estudadas, considerando a possibilidade de m?ltiplos acessos de unidades geradoras. A defini??o desses valores m?ximos se obt?m a partir de um estudo de otimiza??o, no qual as novas perdas n?o superam as do caso base, ou seja, sem a presen?a da gera??o distribu?da. No estudo atendem-se as restri??es de carregamentos nos ramos e tens?es do sistema. Para tratar o problema, prop?e-se um algoritmo baseado no m?todo num?rico de otimiza??o nuvem de part?culas, ou particle swarm optimization PSO, aplicado ao estudo de fluxo de carga convencional CA e ao fluxo de carga ?timo para maximiza??o da penetra??o da gera??o distribu?da. Tamb?m se incorporou o m?todo de Newton-Raphson, como alternativa, para a resolu??o do fluxo de carga. Realiza-se a programa??o computacional no software SCILAB. Testa-se o algoritmo proposto com os dados da rede IEEE-14 barras e de uma rede de distribui??o em alta tens?o (69 kV) do Estado do Rio Grande do Norte, com 25 barras. O algoritmo determina valores permitidos de pot?ncia ativa nominal de gera??o distribu?da, em termos percentuais relativos ? demanda da rede, a partir de valores de refer?ncia

Made available in DSpace on 2014-12-17T14:56:15Z (GMT). No. of bitstreams: 1 DanielWH_DISSERT.pdf: 3818359 bytes, checksum: ac34198b688307ffda10243b5ad47c74 (MD5) Previous issue date: 2013-09-13 / Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico / In the last decade, the renewable energy sources have present a major propulsion in the world due to several factors: political, environmental, financial and others. Within this context, we have in particular the energy obtained through wind, wind energy - that has highlighted with rapid growth in recent years, including in Brazil, mostly in the Northeast, due to it s benefit-cost between the clean energies. In this context, we propose to compare the variable structure adaptive pole placement control (VS-APPC) with a traditional control technique proportional integral controller (PI), applied to set the control of machine side in a conversion system using a wind generator based on Double-Fed Induction Generator (DFIG). Robustness and performance tests were carried out to the uncertainties of the internal parameters of the machine and variations of speed reference. / As fontes de energia renov?veis t?m, na ?ltima d?cada, ganho uma grande propuls?o em todo o mundo devido aos mais diversos fatores: pol?ticos, ambientais, financeiros, entre outros. Dentro deste universo, temos, em especial, a energia obtida atrav?s do vento, energia e?lica - que tem se destacado com um crescimento vertiginoso nos ?ltimos anos, inclusive no Brasil, principalmente na regi?o Nordeste, devido ao seu custo-benef?cio entre as energias "limpas". Neste cen?rio, prop?e-se a compara??o do controlador por posicionamento de polos e estrutura vari?vel (VS-APPC) com o controlador proporcional integral (PI) aplicados em um sistema de convers?o de energia e?lica que utiliza um gerador de indu??o duplamente alimentado (Double-Fed Induction Generator- DFIG). Testes de robustez e desempenho foram realizados com incertezas nos par?metros da m?quina e varia??es de refer?ncia de velocidade

Made available in DSpace on 2014-12-17T14:56:19Z (GMT). No. of bitstreams: 1 ErnanoAJ_DISSERT.pdf: 1903927 bytes, checksum: 0bb4c95cc8f08d85b6af9c71ab44494b (MD5) Previous issue date: 2014-07-11 / Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico / Currently, there are several power converter topologies applied to wind power generation. The converters allow the use of wind turbines operating at variable speed, enabling better use of wind forces. The high performance of the converters is being increasingly demanded, mainly because of the increase in the power generation capacity by wind turbines, which gave rise to various converter topologies, such as parallel or multilevel converters. The use of converters allow effective control of the power injected into the grid, either partially, for the case using partial converter, or total control for the case of using full converter. The back-to-back converter is one of the most used topologies in the market today, due to its simple structure, with few components, contributing to robust and reliable performance. In this work, is presented the implementation of a wind cogeneration system using a permanent magnet synchronous generator (PMSG) associated with a back-to-back power converter is proposed, in order to inject active power in an electric power system. The control strategy of the active power delivered to the grid by cogeneration is based on the philosophy of indirect control / Existem diversas topologias de conversores de pot?ncia aplicadas a sistemas de gera??o de energia e?lica. Os conversores permitem a gera??o de energia com turbinas e?licas em condi??es de velocidade vari?vel do vento, possibilitando um aproveitamento de forma mais eficaz das for?as do vento. A utiliza??o dos conversores possibilita o controle efetivo da pot?ncia injetada na rede, seja de maneira parcial, no caso de utiliza??o de conversores parciais, ou controle total, no caso de utiliza??o de conversores completos. O alto desempenho dos conversores vem sendo cada vez mais necess?rio, principalmente quando se busca a eleva??o da capacidade de gera??o de pot?ncia por parte das turbinas e?licas, o que fez surgir diversas novas topologias de conversores, sejam conversores paralelos ou multin?veis. O conversor na configura??o back-to-back ? um dos mais utilizados no mercado atualmente, devido ? sua estrutura simples, com poucos componentes, contribuindo assim para um desempenho robusto e confi?vel. Neste trabalho, apresenta-se a implementa??o de um sistema de cogera??o e?lica utilizando um gerador s?ncrono a ?m? permanente (PMSG) associado a um conversor de pot?ncia na topologia back-to-back, de maneira a injetar pot?ncia ativa em um sistema el?trico de pot?ncia. A estrat?gia do controle da pot?ncia ativa fornecida pela cogera??o ? rede el?trica ? baseada na filosofia do controle indireto

Made available in DSpace on 2014-12-17T14:57:39Z (GMT). No. of bitstreams: 1 IldefonsoMS.pdf: 1793001 bytes, checksum: 8b7c737ca595a5f30c4e9de306d3fe97 (MD5) Previous issue date: 2007-06-27 / The generation for termoeletricity is characterized as a solid process of conversion of thermal energy (heat) in electric without the necessity of mobile parts. Although the conversion process is of low efficiency the system presents high degree of trustworthiness and low requisite of maintenance and durability. Its principle is based on the studies of termogeneration carried through by Thomas Seebeck in 1800. The frank development of the technologies of solid state for termoeletricity generation, the necessity of the best exploitation of the energy, also with incentive the cogeneration processes, the reduction of the ambient impact allies to the development of modules semiconductors of high efficiency, converge to the use of the thermoeletric generation through components of solid state in remote applications. The work presents the development, construction and performance evaluation of an prototype, in pilot scale, for energy tri-generation aiming at application in remote areas. The unit is composed of a gas lamp as primary source of energy, a module commercial semiconductor for thermoelectric generation and a shirt for production of the luminosity. The project of the device made compatible a headstock for adaptation in the gas lamp, a hot source for adaptation of the module, an exchanger of to be used heat as cold source and to compose first stage of cogeneration, an exchanger of tubular heat to compose second stage of cogeneration, the elaboration of a converter dc-dc type push pull, adequacy of a system of acquisition of temperature. It was become fullfilled assembly of the prototype in group of benches for tests and assay in the full load condition in order to evaluate its efficiency, had been carried through energy balance of the unit. The prototype presented an electric efficiency of 0,73%, thermal of 56,55%, illumination of 1,35% and global of 58,62%. The developed prototype, as the adopted methodology of assay had also taken care of to the considered objectives, making possible the attainment of conclusive results concerning to the experiment. Optimization in the system of setting of the semicondutor module, improvement in the thermal insulation and design of the prototype and system of protection to the user are suggestions to become it a commercial product / A gera??o por termoeletricidade caracteriza-se como um processo s?lido de convers?o de energia t?rmica (calor) em el?trica sem a necessidade de partes m?veis. Embora o processo de convers?o seja de baixa efici?ncia o sistema apresenta alto grau de confiabilidade e baix?ssimos requisitos de manuten??o e durabilidade. Seu princ?pio ? baseado nos estudos de termogera??o realizados por Thomas Seebeck em 1821. O franco desenvolvimento das tecnologias de estado s?lido para gera??o de termoeletricidade, a necessidade do melhor aproveitamento da energia, inclusive com incentivo a processos de cogera??o, a redu??o do impacto ambiental aliados ao desenvolvimento de m?dulos semicondutores de alta efici?ncia, convergem para o uso da gera??o termoel?trica atrav?s de componentes de estado s?lido em aplica??es remotas. O trabalho apresenta o desenvolvimento, constru??o e avalia??o de performance de um prot?tipo, em escala piloto, para tri-gera??o de energia visando aplica??o em ?reas remotas. A unidade ? composta de um lampi?o a g?s combust?vel como fonte prim?ria de energia, um m?dulo semicondutor comercial para gera??o termoel?trica e uma camisa para produ??o da luminosidade. O projeto do dispositivo compatibilizou um cabe?ote para adapta??o no lampi?o, uma fonte quente para adapta??o do m?dulo, um trocador de calor para ser utilizado como fonte fria e compor o 1? est?gio de cogera??o, um trocador de calor tubular para compor o 2? est?gio de cogera??o, a elabora??o de um conversor cc-cc tipo push pull, adequa??o de um sistema de aquisi??o de temperatura. Realizou-se a montagem do prot?tipo em bancada para testes e ensaio na condi??o de carga plena a fim de avaliar a sua efici?ncia, sendo realizado balan?o de energia da unidade. O prot?tipo apresentou uma efici?ncia el?trica de 0,73%, t?rmica de 56,55%, de ilumina??o de 1,35% e global de 58,62%. O prot?tipo desenvolvido, como tamb?m a metodologia de ensaio adotada atenderam aos objetivos propostos, possibilitando a obten??o de resultados conclusivos acerca do experimento. Otimiza??o no sistema de fixa??o do m?dulo semicondutor, melhoramento na isola??o t?rmica e design do prot?tipo e sistema de prote??o ao usu?rio s?o sugest?es para torn?-lo um produto comercial

Made available in DSpace on 2014-12-17T14:58:00Z (GMT). No. of bitstreams: 1 RairamFCA_DISSERT2.pdf: 4758176 bytes, checksum: bfb1653549a50848b4721bda9a78bd6e (MD5) Previous issue date: 2010-03-26 / The pumping through progressing cavities system has been more and more employed in the petroleum industry. This occurs because of its capacity of elevation of highly viscous oils or fluids with great concentration of sand or other solid particles. A Progressing Cavity Pump (PCP) consists, basically, of a rotor - a metallic device similar to an eccentric screw, and a stator - a steel tube internally covered by a double helix, which may be rigid or deformable/elastomeric. In general, it is submitted to a combination of well pressure with the pressure generated by the pumping process itself. In elastomeric PCPs, this combined effort compresses the stator and generates, or enlarges, the clearance existing between the rotor and the stator, thus reducing the closing effect between their cavities. Such opening of the sealing region produces what is known as fluid slip or slippage, reducing the efficiency of the PCP pumping system. Therefore, this research aims to develop a transient three-dimensional computational model that, based on single-lobe PCP kinematics, is able to simulate the fluid-structure interaction that occurs in the interior of metallic and elastomeric PCPs. The main goal is to evaluate the dynamic characteristics of PCP s efficiency based on detailed and instantaneous information of velocity, pressure and deformation fields in their interior. To reach these goals (development and use of the model), it was also necessary the development of a methodology for generation of dynamic, mobile and deformable, computational meshes representing fluid and structural regions of a PCP. This additional intermediary step has been characterized as the biggest challenge for the elaboration and running of the computational model due to the complex kinematic and critical geometry of this type of pump (different helix angles between rotor and stator as well as large length scale aspect ratios). The processes of dynamic generation of meshes and of simultaneous evaluation of the deformations suffered by the elastomer are fulfilled through subroutines written in Fortan 90 language that dynamically interact with the CFX/ANSYS fluid dynamic software. Since a structural elastic linear model is employed to evaluate elastomer deformations, it is not necessary to use any CAE package for structural analysis. However, an initial proposal for dynamic simulation using hyperelastic models through ANSYS software is also presented in this research. Validation of the results produced with the present methodology (mesh generation, flow simulation in metallic PCPs and simulation of fluid-structure interaction in elastomeric PCPs) is obtained through comparison with experimental results reported by the literature. It is expected that the development and application of such a computational model may provide better details of the dynamics of the flow within metallic and elastomeric PCPs, so that better control systems may be implemented in the artificial elevation area by PCP / O sistema de bombeamento por cavidades progressivas est? sendo cada vez mais empregado na ind?stria do petr?leo, devido ? sua capacidade de eleva??o de ?leos altamente viscosos ou de fluidos com grandes concentra??es de areia ou outras part?culas s?lidas. Uma Bomba de Cavidades Progressivas (BCP) ? composta, basicamente, por um rotor - uma pe?a met?lica de forma semelhante a um parafuso exc?ntrico, e um estator - um tubo de a?o revestido internamente por uma h?lice dupla, a qual pode ser r?gida ou deform?vel/elastom?rica. Em geral, uma BCP ? submetida a uma combina??o de press?o do po?o com press?o gerada pelo pr?prio processo de bombeio. Em BCPs elastom?ricas, essa combina??o de esfor?os comprime o estator, gerando ou aumentando a folga existente entre o rotor e o estator, reduzindo, portanto, o efeito de veda??o entre suas cavidades. Tal abertura da regi?o de selagem produz o que ? conhecido como escorregamento do fluido, diminuindo, com isso, a efici?ncia de sistema de bombeio por BCP. Dessa maneira, este trabalho se prop?e a desenvolver um modelo computacional tridimensional transiente do processo din?mico da intera??o fluido-estrutural (FSI) que ocorre no interior de BCPs met?licas e elastom?ricas. O objetivo principal ? avaliar, a partir do uso do modelo desenvolvido, as caracter?sticas din?micas de efici?ncia de bombeio por BCPs, em fun??o de informa??es locais e instant?neas detalhadas dos campos de velocidade, press?o e deforma??o no seu interior. Para o alcance de tais metas (desenvolvimento e uso do modelo), fez-se necess?rio o desenvolvimento de uma metodologia pr?pria para gera??o de malhas computacionais din?micas, m?veis e deform?veis, representando as regi?es fluida e estrutural de uma BCP. Tal procedimento caracterizou-se como o maior desafio para a elabora??o do modelo computacional, devido ? cinem?tica complexa e ? geometria cr?tica desse tipo de bomba (?ngulos de h?lice diferentes entre rotor e estator e grandes diferen?as de escala de comprimento). Os processos de gera??o din?mica das malhas e de avalia??o simult?nea das deforma??es sofridas pelo elast?mero s?o realizados atrav?s de sub-rotinas em linguagem Fortran 90, as quais interagem dinamicamente com o software de din?mica dos fluidos computacional CFX/ANSYS. Desde que o modelo linear el?stico ? empregado para avaliar as deforma??es elastom?ricas, n?o ? necess?rio usar nenhum software para an?lise estrutural. Entretanto, uma proposta inicial para simula??o din?mica no ANSYS empregando-se modelos constitutivos hiper-el?sticos para o elast?mero ? tamb?m apresentada no presente trabalho. A valida??o dos resultados produzidos com a presente metodologia (gera??o de malha, simula??o do escoamento em BCPs met?licas e simula??o da intera??o fluido-estrutural em BCPs elastom?ricas) ? obtida atrav?s da compara??o com resultados experimentais reportados pela literatura. Vislumbra-se que o desenvolvimento e aplica??o de tal ferramenta computacional poder?o fornecer maiores detalhes da din?mica do escoamento no interior de BCPs met?licas e elastom?ricas, de maneira que melhores sistemas de controle possam ser implementados na ?rea de eleva??o artificial por BCPs

Made available in DSpace on 2014-12-17T15:01:15Z (GMT). No. of bitstreams: 1 MagnaASB.pdf: 1635517 bytes, checksum: df420c88397a6cd630a5381fcef348b7 (MD5) Previous issue date: 2004-09-02 / The production of petroleum is frequently accomplished with great volumes of water, that it is carried of the underground with the oil. It is a challenge of the present century the development of technologies that allow the use of waste water for purposes that consume great amounts of water and don't demand as rigid as the one of the drinking water requirements. The solar distillation has been configuring as an alternative of clean technology for desalination of brine and saline. Besides causing the minimum possible damage to the environment, it takes advantage of an abundant and free energy source: the solar energy. That study aims to develop a Solar Distillator for treatment of the produced water of the oil wells, to obtain an efluent to use in agriculture and vapor generation. The methodology for collection, conservation and analysis of the physical-chemical parameters obeyed the norms in APHA (1995). The sampling was of the composed type. Experiments were accomplished in the solar distillation pilot and simulation in thermostatic bathing. The operation was in batch system and for periods of 4, 6 and 12 h. The developed Distillator is of the type simple effect of two waters. It was still tested two inclination angles for covering; 20? and 45?. The Distillator presented minimum of 2,85 L/m2d revenues and maximum of 7,14 L/m2d. The removals of salts were great than 98%. The removal of TOC in the simulation was great than 90%. In agreement with the data of energy and mass balance, it was verified that the developed solar Distillator presented compatible revenues with those found in literature for similar types. It can be inferred that the obtained distilled water assists to the requirements CONAMA in almost all the points and could be used for irrigation of cultures such as cotton and mamona. As the distilled water has characteristics of fresh water it can be used in the generation of vapor / A produ??o de petr?leo ? realizada freq?entemente com grandes volumes de ?gua, que ? carreada do subsolo junto com o ?leo. ? desafio do presente s?culo o desenvolvimento de tecnologias que possibilitem ou uso ou reuso de efluentes para outros fins. A destila??o solar ? uma alternativa de tecnologia limpa para dessaliniza??o de ?guas salobras e salinas. Esse estudo visa desenvolver um Destilador Solar para tratamento da ?gua de produ??o de petr?leo, com vistas a se obter um efluente pass?vel de utiliza??o na agricultura e gera??o de vapor. A metodologia para conserva??o e an?lise dos par?metros f?sico-qu?micos obedeceu preconiza??o do APHA (1995). A amostragem foi do tipo composta. Foram realizados experimentos no destilador solar piloto e simula??o em banho termost?tico. A opera??o foi em sistema de batelada e por per?odos de 4, 6 e 12 h. O destilador desenvolvido ? do tipo simples efeito de duas ?guas. Testou-se ainda dois ?ngulos de inclina??o para cobertura; 20? e 45?. O destilador apresentou rendimentos m?nimo de 2,50 L/m2d e m?ximo de 7,5 L/m2d. As remo??es de sais foram superiores a 98%. A remo??o de TOC na simula??o foi superior a 90%. De acordo com os dados dos balan?os energ?tico e de massa, verificou-se que o destilador solar desenvolvido apresentou rendimentos compat?veis com os encontrados na literatura para seus similares. Enfatiza-se que o isolamento utilizado n?o estava nas condi??es de otimiza??o, logo, esse rendimento pode ser melhorado. Pode-se inferir que a ?gua destilada obtida atende aos requisitos CONAMA em quase todos os pontos, podendo ser utilizada, com ressalvas, na irriga??o de culturas n?o comest?veis como o algod?o e a mamona. Como a ?gua destilada tem caracter?sticas de ?gua doce pode ser utilizada na gera??o de vapor