Aircraft manufacturer Aquavion Systems is currently designing and constructing prototypes for its revolutionary new fleet of aircraft called the SeaStryder. During the prototyping phase, it was discovered that the center-of-gravity of the SeaStryder600 was too far aft and outside of the acceptable range. To solve this design issue, it was hypothesized that the weight of the horizontal stabilizer may be reduced without compromising its structural integrity. The following document analyzes this hypothesis and provides two alternative designs. Each design exceeds the design requirements, meets additional requirements requested by industry, and provides a significant degree of weight savings. The first design provides a 25% weight reduction. The second design provides an 18% weight reduction as well as a 160% increase in loading capacity. The designs proposed have both been verified through the use of Finite Element Analysis as well as by means of experimentation where two prototype wings were constructed and tested to failure confirming the analytical results.

This thesis reports on the investigations of resistive-capacitive (RC) loaded bow-tie antennas with special emphasis on impulse ground penetrating radar applications. Impulse radiation for ground penetrating radar is a challenging research topic because of the unique problem arising from impulse radiation: late-time ringing, which usually masks the important echo signals from the targets. While resistive loading is a common solution for eliminating late-time ringing, use of resistive loading typically sacrifices the radiation efficiency. In this thesis, a resistive-capacitive loading technique is investigated for a circular bow-tie antenna in the attempt to reduce/suppress the late-time ringing as well as to maintain a relatively high radiation efficiency. To implement the system, a microstrip differentiator, which converts a monopulse into a Gaussian-like monocycle to be used as input impulse, is presented. Further, specially designed coplanar waveguide/coplanar strip (CPW/CPS) baluns embedded with Chebyshev transformers of characteristic impedance up to 120 have been constructed and tested. To evaluate the system, instead of using the conventional peak voltage value of the radiated waveform, average radiated energy, average ringing energy, relative radiation efficiency and relative ringing efficiency are utilized and these metrics are easily established using low-cost low-sensitivity probes. Measurement results show that the RC-loading scheme is functioning as expected and the impulse system as a whole is capable of reducing the late-time ringing energy to 50% while maintaining average radiation energy as 83% when compared with capacitive loading cases. / October 2006

This research used classical and molecular epidemiology tools to assess the potential importance of feedlot cattle as Campylobacter reservoirs. The project was conducted from November 2004 to September 2005 in southern Alberta.<p> Fresh pen-floor fecal samples were collected from commercial feedlot cattle near slaughter weight in seven feedlots. Overall, 87% of 2,776 fecal samples were culture positive for Campylobacter species (86% of 1,400 in winter, 88% of 1,376 in summer), and 69% of 1,486 Campylobacter positive isolates were identified as <i>Campylobacter jejuni</i>. After accounting for clustering within pen and feedlot, the number of days-on-feed and feedlot size were associated (p ¡Ü 0.05) with Campylobacter species isolation rates.<p> Retail ground beef was collected from 60 grocery stores (four chains, three cities). None of the 1,200 packages were culture positive for Campylobacter species. Polymerase chain reaction (PCR) results from a subset of samples (n=142) indicated that 48% of packages were positive for Campylobacter DNA. By species, 14.8% (21/142), 26.8% (38/142) and 1.4% (2/142) of packages were PCR positive for <i>C. jejuni</i>, <i>C. coli</i> and <i>C. hyointestinalis</i> DNA, respectively. The collection period (1, 2, 3 or 4) was associated (p ¡Ü 0.05) with the odds of detecting Campylobacter species DNA using PCR.<p> Oligonucleotide DNA microarrays were used as a platform for comparative genomic hybridization (CGH) analysis of 87 C. jejuni isolates (46 bovine, 41 human) obtained within the same geographical regions and time frame. Of the 13 CGH clusters identified based on overall comparative genomic profile similarity, nine contained human and cattle isolates, three contained only human isolates, and one contained only cattle isolates. In addition, human clinical and feedlot cattle C. jejuni isolates were compared on a gene-by-gene basis and only a small number of the 1,399 genes tested were unequally distributed between the two groups (p ¡Ü 0.05).<p> The high isolation rates of Campylobacter species and <i>C. jejuni</i> reported here may have implications for food safety, public health and environmental contamination. Our findings suggest that feedlot cattle and human <i>C. jejuni</i>strains are very similar and may be endemic within southern Alberta.

Soil moisture and ground thaw state are both indicative of a hillslopes ability to transfer water. In cold regions in particular, it is widely known that the wetness of surface soils and depth of ground thaw are important for runoff generation, but the diversity of interactions between surface soil moisture and ground thaw themselves has not been studied. To fill this knowledge gap, detailed shallow soil moisture and thaw depth surveys were conducted along systematic grids at the Baker Creek Basin, Northwest Territories. Multiple hillslopes were studied to determine how the interactions differed along a spectrum of topological, typological and topographic situations (T³ template). Results did not show a simple relationship between soil moisture and ground thaw as was expected. Instead, correlation was a function of wetness such that the correlation between soil moisture and ground thaw improved with site wetness. To understand why differences in soil moisture and ground thaw state arose, water and energy fluxes were examined for these subarctic study sites to discern the key processes controlling the patterns observed. Results showed that the key control in variable soil moisture and frost table interactions among the sites was the presence of surface water. At the peatland and wetland sites, accumulated water in depressions and flow paths maintained soil moisture for a longer duration than at the hummock tops. These wet areas were often locations of deepest thaw depth due to the transfer of latent heat accompanying lateral surface runoff. Although the peatland and wetland sites had large inundation extents, modified Péclet numbers indicated that the relative influence of external and internal hydrological processes at each site were different. Continuous inflow from an upstream lake into the wetland site caused advective and conductive thermal energies to be of equal importance to ground thaw. The absence of continuous surface flow at the peatland and valley sites led to the dominance of conductive thermal energy over advective energy for ground thaw. A quantitative explanation for the shallow soil moisture-ground thaw patterns was provided by linking hydrological processes and hillslope storage capacity with the calculated water and energy fluxes as well as the modified Péclet number. These results suggest that the T&#x00B3; template and the modified Péclet number could be very useful parameters for differentiating landscape components in modeling soil moisture and frost table heterogeneity in cold regions.

Pulse crops have been long associated with biological dinitrogen fixation and therefore improve the sustainability of cropping systems when included in rotation. However, studies indicate there may be additional benefits of including pulse crops in rotation. To quantify these potential benefits, soil processes and properties related to nitrogen (N) and carbon (C) cycling were examined in five crop rotations with and without field pea (<i>Pisum sativum</i> L.) in Scott, Saskatchewan. Gross mineralization and nitrification rates were determined using the 15N isotope dilution technique in intact soil cores. To estimate the proportion of nitrous oxide (N2O) emissions derived from nitrification related processes rather than denitrification processes tracer techniques using 15N were used. Field incubations were performed in 2008 at seeding (May 13), anthesis (July 8) and just after harvest (October 8). Mean mineralization and nitrification rates were not significantly different among rotations on any date and there was no significant difference in mean N2O emissions among rotations. From labeled 15NO3- cores, it was determined that nitrification-related processes were the major contributors to N2O emissions. There was no difference among the rotations in microbial biomass carbon (MB-C) or microbial biomass N (MB-N) with the exception of MB-C in the continuous field pea (FP) and the canola (<i>Brassica napus</i> L.)-wheat (<i>Triticum aestivum</i> L.)-field pea (CNL-W-FP) rotation at anthesis. There was no effect of rotation on dissolved organic carbon (DOC) and only seasonal differences were observed with DOC levels being lower before seeding than at anthesis and post-harvest. Based on the results obtained from a single growing season, our results show that N benefits of including field pea in rotation, beyond dinitrigen fixation, were not detectable and that the immediate N benefit of including field pea in rotation may be due simply to the direct effects of biological dinitrogen (N2) fixation. However, there have been reports of pulse crop benefits to succeeding crops in rotation. As a result, we investigated both the quantity and quality of crop residues, which can have an impact on soil properties and processes. Plants enriched with isotopic tracers can be used to trace crop residue decomposition to various C pools but only if the tracer is homogeneously distributed throughout the plant. In order to determine if repeat-pulse labeling could be used to trace crop residue decomposition, this method was followed using 13CO2 to enrich plant material of field pea and canola plants in a controlled environment. The distribution of 13C throughout the plant parts (roots, stem, leaves, and pod) and biochemical fractions [acid detergent fiber (ADF) and acid detergent lignin (ADL)] were determined. It was found that 13C was not homogeneously distributed throughout the plant parts or biochemical fractions. The pod fraction in particular was much less enriched in comparison to the other fractions. The ADL fraction was less enriched than the ADF fraction. Because of the heterogeneity of the label throughout the plant, modifications of the method are needed and 13C distribution through out the plant needs to be assessed before the repeat-pulse method can be used to trace C residue through various C pools. Nevertheless, root contributions to below-ground C were successfully determined from the enriched root material and the resulting enriched soil. It was found that canola contributed more above- and below-ground residues than field pea, however canola was also higher in ADF and ADL fractions indicating a more recalcitrant residue. Research should continue to better define the impact of pulse crop residues on C and N cycling and subsequent crops in rotation.

Conformal arrays possess certain desirable characteristics for deployment on unmanned aerial vehicles and other payload-limited platforms: aerodynamic design, minimal payload weight, increased field of view, and ease of integration with diverse sensor functions. However, the conformal arrays nonplanar geometry causes high adaptive losses in conventional space-time adaptive processing (STAP) algorithms. In this thesis, we develop a conformal array signal model and apply it to evaluate the performance of conventional STAP algorithms on simulated ground clutter data. We find that array-induced clutter nonstationarity leads to high adaptive losses, which greatly burden detection performance. To improve adaptive performance, we investigate the application of existing equivalent-linear-array transformations and develop novel deterministic and adaptive angle-Doppler compensation techniques, which align nonstationary clutter returns. Through the application of these techniques, we are able to nearly fully mitigate the nonstationary behavior yielding performance similar to that of a conventional planar array. Finally, we investigate the impact of array errors on the performance of conformal arrays, and propose several array calibration techniques as ameliorating solutions.

The highly flexible HALE (High Altitude Long Endurance) aircraft analysis methodology is of interest because early studies indicated that HALE aircraft might have different vibration and aeroelastic characteristics from those of conventional aircraft. Recently the computer code Nonlinear Aeroelastic Trim And Stability of HALE Aircraft (NATASHA) was developed and used to the flight dynamics and aeroelastic analysis of flying wing HALE aircraft. Further analysis improvements were required to extend its capability to the ground vibration test (GVT) environment and to both GVT and aeroelastic behavior of HALE aircraft with other configurations. First, the geometrically exact fully intrinsic beam theory was extended to treat other aircraft configurations modeled as an assembly of beam elements. It includes auxiliary elevator input in the horizontal tail and fuselage aerodynamics. Second, the methodology was extended to treat the GVT environment to provide modal characteristics for model validation. A newly developed bungee formulation is coupled to the intrinsic beam formulation for the GVT modeling. After the coupling procedures, the whole formulation cannot be fully intrinsic because the geometric constraint by bungee cords makes the system statically indeterminant. Third, because many HALE aircraft are propeller driven, the methodology was extended to include an engine/nacelle/propeller system using a two-degree-of-freedom model. This step was undertaken to predict a dynamic instability called ``whirl flutter," which can be exhibited in such HALE aircrafts. For simplicity, two fundamental assumptions are made: constant approximation on the propeller aerodynamics and the use of equivalent three-bladed counterpart for two-bladed propeller system to obviate the need for Floquet theory. The validity of these assumptions is verified by investigating the periodic effect of side forces and hub moments and the periodic inertia effect. Finally, parametric studies show how the current methodology can be utilized as a unified preliminary analysis tool for the vibration and aeroelastic analysis of highly flexible HALE aircraft.

With electronic devices trending toward higher clock rates, lower voltage levels, and smaller form factors, the simultaneously switching noise (SSN), which is induced in package and printed circuit board, is one of the major factors affecting the performance and design of the high speed digital circuits. This noise will lead to false switching and malfunctioning in digital and/or analog circuits, and causes serious signal integrity (SI) and electromagnetic interference (EMI) problems for the high speed digital systems. Therefore, mitigating the SSN becomes a major challenge for the high speed circuits design. In this thesis, first of all, we introduce and discuss previously proposed solutions to suppress the SSN. These solutions include the use of decoupling capacitors, isolation moats, and electromagnetic bnadgap (EBG) structures. We analyzed the EBG structures and generated some EBG design rules. As the speed of digital circuits moving toward higher frequencies, the Double L-bridge EBG structure can be used to improve the performance of Hybrid EBG structure by employing the EBG design rules that were generated. The Double L-bridge EBG structure design improved the behavior at the high frequencies, which also maintained the low frequency performance. It is demonstrated numerically and experimentally. For fast estimating the stopband, we use one-dimensional lump circuit model. Then, we propose another structure, named Double Cross EBG structure. This design, compared to the Double L-bridge EBG structure, not only maintained the high frequency performance, but also improved the low frequency behavior. It is also both experimentally and numerically validated.

To identify the dynamic model of the treadmill, this study uses the piezoelectricity material (Po1yviny-lidene fluoride, PVDF) to measure the force under treadmill. With this dynamic model, the ground reaction force (GRF) can be derived from the PVDF sensors. The reliability and precision of the GRF results are verified by replacing the PVDF with the traditional load cell (Force measurement devices). To verify the accuracy of treadmill model, this study acquires three different types of GRF signals (marking time, walking and running) from ten subjects. For the marking time case, the correlation coefficients between the actual and predicated GRF signals are approximately 0.98. This study also demonstrates that the proposed model can provide sufficient bandwidth for the walking and running GRF signals. Finally, via comparing the average GRF profile, inter-personal differences of the GRF signal can be observed. Among the three tested locomotion patterns, the marking time GRF has the highest similarity whereas the running GRF signals has the largest variability.

Treadmill is a highly popular fitness equipments. One of the most important purposes of running is to consume redundant energy of the body. A well designed exercise intensity plan can achieve the benefits of exercise while avoiding sport injuries. Calculating the appropriate exercise intensity is therefore a valuable study issue. Current commercially available treadmills cannot provide sufficient physiological data. In particular, in order to measure the ground reaction force (GRF) of the runners, traditional approach is to design treadmill as a rigid body. Such treadmills are thus expensive and heavy. To estimate heart rate (HR), ECG measurement is typically required. However, sweat can cause the patch to loose and the quality of the signal transmission can also be degraded by environmental noises. Thus the aim of this work is to develop a simple and effective method to assess exercise intensity by estimating HR with GRF.. To achieve this goal, this work places load cells under the legs of the treadmill. By constructing the dynamic model of the treadmill via system identification technique, we can estimate the actual GRF from the measurements of the load cells. After computing the TVI (Total Vertical Impulse) index from the GRF, this work then investigates the linear relationship between TVI and running energy consumption by estimating HR from TVI. Based on the known relationship between HR and exercise intensity, we can observe the runner¡¦s condition from the speed of HR recovery and the HR time response during running. By means of linear regression method, it is found that the linear relations between TVI index and these HR measures are statistically significant. The p-value of such statically tests become even smaller when TVI index is normalized.