Neste trabalho, é apresentado um estudo sobre a influência de aditivos em banhos de eletrodeposição de Au, análise da morfologia dos depósitos de Au e o crescimento de multicamadas da liga AuxSny por deposição eletroquímica. Os banhos de eletrodeposição estudados são baseados em uma composição, comum na literatura, formada por tetraclorourato(III) de potássio (KAuCl4), cloreto de estanho(II) (SnCl2), sulfito de sódio (Na2SO3), e citrato de amônio [(NH4)HC6H5O7]. Os contatos de solda da liga AuxSny, aplicáveis em diversos dispositivos microeletrônicos, podem ser formadas de maneira mais econômica a partir de banhos eletroquímicos. Banhos ácidos e reagentes de baixa toxicidade são exigências comuns dos novos banhos de eletrodeposição. A formação de multicamadas permite, ainda, ampliar o uso do metal de solda em dispositivos sensíveis a altas temperaturas, devido ao baixo ponto de fusão da liga. A obtenção das ligas AuxSny utilizando deposição eletroquímica, foi feita com base no estudo sobre banho de eletrodeposição e seus depósitos, a partir de um banho para deposição da liga AuxSny já conhecido. O aprimoramento do banho de eletrodeposição foi focado no banho de eletrodeposição de Au, com três opções de aditivos, buscando avaliar as características dos depósitos e o tempo de estabilidade do banho. Os aditivos utilizados foram hipofosfito de sódio (NaH2PO2), metanal (HCHO) e tiossulfato de sódio (Na2S2O3), separadamente. Esses banhos foram analisados por voltametria cíclica, e os depósitos obtidos a partir de eletrodeposições foram caracterizados por Espectrometria por Retroespalhamento de Rutherford (RBS), Microscopia Eletrônica de Varredura (SEM) e, em alguns casos, por Espectrometria de Energia Dispersiva de Raios X (EDS). Análises de dimensão fractal e de escalamento dinâmico da rugosidade forneceram detalhes importantes sobre a morfologia superficial dos depósitos. .A adição de Na2S2O3 ao banho permitiu o desenvolvimento de um novo banho de eletrodeposição para a co-deposição de Au AuxSny. O Na2S2O3 atua como um complexante dos íons de Au(I) juntamente com o sulfito de sódio. O emprego de 3 g L-1 de Na2S2O3 evita a degradação do banho durante as eletrodeposições. Finalmente, o estudo da eletrodeposição de multicamadas foi feito por controle do potencial aplicado e por controle da corrente aplicada. As multicamadas obtidas apresentaram camadas da liga AuxSny com a concentração de Sn incorporado, variando entre 6 % e 49 % (em porcentagem atômica). / It is shown in this work a study about the influence of additives in baths for electrodeposition of Au, analysis of morphology of gold deposits and the growth of multilayered AuxSny alloys from improved electrodeposition baths based on a common composition of the literature containing potassium gold(III) chloride (KAuCl4), tin(II) chloride (SnCl2), sodium sulfite (Na2SO3) and ammonium citrate dibasic [(NH4)HC6H5O7]. The AuxSny solders are commonly used in microelectronic devices. These solders can be applied in a number of ways, and electrochemical deposition is an attractive alternative due to the low cost process. Acidic baths and low toxicity reagents are common requirements of new electrochemical baths. The multilayered AuxSny alloys are applicable to temperature sensitive materials due to its reduced melting point temperature. Therefore, the study of electrodeposition of AuxSny alloys began with an already known bath and aiming its improvement. The focus of interest was the gold bath, which received additives to improve control of the deposits and their stability. The additives used were sodium hypophosphite (NaH2PO2), methanal (HCHO) and sodium thiosulfate (Na2S2O3), one of each time. These baths were analyzed by cyclic voltammetry and the deposits obtained from these baths were analyzed by Rutherford Backscattering Spectrometry (RBS), Scanning Electron Microscopy (SEM) and, in some cases, Energy Dispersive Spectrometry (EDS). Fractal dimension and dynamic scaling of the surface width analysis allowed one to quantify the surface morphology details. The addition of Na2S2O3 to the bath allowed the development of a new electrodeposition bath for co-deposition of AuxSny. The Na2S2O3 acts as complexing agent of Au(I) ions together with sodium sulfite. The use of 3 g L-1 of Na2S2O3 avoids bath degradation during the electrodepositions. Potential-controlled and current-controlled electrodepositions were employed to obtain multilayers of AuxSny alloys. The multilayer deposits obtained presented between 6 atomic % and 49 atomic % of tin.

Tesis para optar al grado de Magíster en Estudios de Género y Cultura, mención en Humanidades / [...] Desde esta perspectiva, planteamos que la construcción de la subjetividad de las mujeres católicas de la Liga de Damas Chilenas, en tanto sujetos femeninos envueltos en relaciones de poder, se posicionaron como un modelo de lo que significa ser una señora de bien frente a los cambios modernizadores de comienzo de la década de 1910, asumiendo la responsabilidad de la defensa moral de las costumbres que sintieron amenazadas. En ese sentido, los actos, decisiones e iniciativas de las señoras de la Liga constituyeron una negociación entre los discursos dominantes y sus intervenciones en el espacio público, subvirtiendo el rol tradicional, doméstico y silencioso de la posición de las mujeres de clase alta. Para ello, utilizaron el mismo discurso de feminidad como instrumento de resistencia y de afirmación de su identidad genérica y de clase, incluyendo prácticas más flexibles de lo que significaba ser una señora de bien, pero ahora fuera de las murallas del hogar.

Title: The dependence of the amount of revenue of the highest ranking football leagues based on the ranking of countries according to the UEFA club coefficient. Objectives: In its work, the main aim was to examine the correlation between the amount of income of the highest football leagues and the countries' rankings on the UEFA club coefficient ladder. Shall the correlation be proven, further aims of its work would be description and quantification of the correlation. One of the side aims is the analysis of the nowadays football phenomena and proving its worldwide significance. Methods: In its work, publicly available data (professional literature, annual reports, statistical yearbooks) was analysed. On the basis of the data collection and analysis, the data was compiled and compared with each other in order to follow trends and create thorough conclusions. On the basis of the correlation between the monitored indicators, these correlations were measured. For the purposes of the correlation measurement, the statistical method of regression analysis was used. Results: The main finding of this work is that the correlation between the amount of income of the highest football leagues and the contries' rankings on the UEFA club coefficient ladder was proven. This finding is based on the results of the...

This paper investigates presence of the superstar effect among users of the Czech fantasy league during seasons between years 2010 and 2013. Both main views are taken into consideration, namely Rosen's and also Adler's theory. Using regression models employing the method of least squares for panel data I show a positive superstar effect according to Rosen's theory in case when the star players are defined by their ability to score great amounts of goals. The presence of a positive superstar effect according to Adler's theory is not apparent in the models, which can be caused by the authors of the fantasy league overestimating the value of the star players beside their performance.

O presente trabalho apresenta a análise da resistência ao desgaste abrasivo de um revestimento duro e do aço SAE 5160. O revestimento foi obtido pela deposição de uma liga ferrosa através de processo de soldagem \"TIG\" sobre um aço ABNT 1020. Aliga foi desenvolvida com a utilização de CR e Nb como elementos formadores de carbonetos, proporcionando uma microestrutura constituída, no estado bruto de fusão, de uma rede de carbonetos (Cr, Fe)7C3 interdendríticos e NbC dispersos em uma matriz austenítica. Corpos de prova revestidos foram submetidos a tratamentos térmicos de normalização, têmpera, sub-zero e revenido, visando a obtenção de diferentes microestruturas na matriz, enquanto que o aço SAE 5160 foi temperado e revenido de acordo com o procedimento utilizado na confecção de ferramentas agrícolas com este material. A resistência ao desgaste do revestimento foi superior à do aço SAE 5160 nos dois tipos de ensaios de abrasão realizados, sendo os melhores desempenhos apresentados pelo revestimento temperado no ensaio realizado com equipamento do tipo pino sobre lixa e pelo revestimento temperado e revenido no ensaio do tipo roda de borracha/areia seca. A identificação dos mecanismos de remoção de material predominantes nos ensaios abrasivos foi possibilitada pela observação das superfícies desgastadas dos corpos de prova através de microscopia eletrônica de varredura. / The present work presents an analysis of the abrasive wear resistance of a hardfacing and of the SAE 5160 steel. The hardfacing was obtained by the deposition of a iron based alloy through \"TIG\" welding on a ABNT 1020 steel. This alloy was developed with the use of Cr and Nb as carbide forming elements , resulting in a microstructure formed by a carbide net of M7C3 interdendritic in a austenitic matrix. The hardfacing samples suffered heat treatment of normalizing, hardening, tempering and subzero, viewing the achievement of differents microstructure, while the SAE 5160 steel suffered hardening and tempering according to the production process used in the agricutural tool manufacturing. The wear resistance of the hardfacing overcame the SAE 5160 steel in both types of abrasion wear tests, and the best performances were presented by hardening hardfacing in the pin wear test and by the tempering hardfacing in the rubber wheel/dry sand test. The identification of the material removal mechanisms in the abrasive tests was made by the observation of the worn surfaces of the samples through the scanning eletronic microscopy.

The aim of this study was to evaluate the cyclic and torsional fatigue resistance of Nickel-Titanium rotary instruments manufactured by different thermal treatments. Were tested a total of 140 rotary instruments (n=20): Genius (GN size 25, .04 taper), Trushape (TS size 25, .06 taper), Logic (LOG size 25, .06 taper), Vortex Blue (VB size 25, .06 taper), ProTaper Gold (PTG size 25, .08 taper), Hyflex CM (HCM size 25, .06 taper) and Hyflex EDM (EDM size 25, .08 taper). Cyclic fatigue resistance testing was performed using an artificial stainless steel canal with a curvature (60° angle and 5- mm radius) located at 5 mm from the tip. The files (n=10) rotated until fracture and time was recorded in seconds. The torsional test evaluated the angular deflection and torque at failure of the instruments (n=10) at 3 mm from the tip according to ISO 3630- 1. The fractured surface of five instruments of each brand was observed by using scanning electron microscopy (SEM). Data were analysed using one-way ANOVA and Tukey tests, and the level of significance was set at 5%. The cyclic fatigue resistance value of EDM size 25, .08 taper was significantly higher than those of all instruments tested (P<0.05). The LOG size 25, .06 taper showed a higher cyclic fatigue resistance than those of GN size 25, .04 taper; TS size 25, .06 taper (P<0.05). There was no difference among the others groups. The torsional test showed that PTG size 25, .08 taper had the highest torsional strength value of all instruments tested followed by VB size 25, .06 taper and EDM size 25, .06 taper (P<0.05). The LOG size 25, .06 taper showed significant difference only with GN size 25, .04 taper (P<0.05). No difference was found among the others groups (P>0.05). In relation to angular deflection, the GN size 25, .04 taper; TS size 25, .06 taper; HCM size 25, .06 taper, and EDM size 25, .08 taper showed significantly higher values until fracture than the others groups (P<0.05). No difference was found among PTG size 25, .08 taper, LOG size 25, .06 taper, and VB size 25, .06 taper (P<0.05). The EDM size 25, .08 taper presented the highest cyclic fatigue resistance among all the tested instruments. For the torsional test, the PTG size 25, .08 taper showed highest torsional strength and lowest angular deflection values. / O objetivo deste estudo foi avaliar a resistência às fadigas cíclica e torsional de instrumentos rotatórios de Níquel - Titânio fabricados por diferentes tratamentos térmicos. Foram testados o total de 140 instrumentos (n=20): Genius (GN diâmetro 25, conicidade .04), Trushape (TS diâmetro 25, conicidade .06), Logic (LOG diâmetro 25, conicidade .06), Vortex Blue (VB diâmetro 25, conicidade .06), ProTaper Gold (PTG diâmetro 25, conicidade .08), Hyflex CM (HCM diâmetro 25, conicidade .06) e Hyflex EDM (EDM diâmetro 25, conicidade .08). O teste de resistência à fadiga cíclica foi realizado utilizando um canal artificial de aço inoxidável com curvatura (ângulo de 60° e raio de 5mm) localizada a 5 mm da ponta. Os instrumentos (n=10) foram rotacionados até a fratura e tempo foi registrado em segundos. O teste torsional avaliou a deflexão angular e torque até a falha dos instrumentos (n=10) a 3 mm da ponta de acordo com a ISO 3630-1. A superfície da fratura de 5 instrumentos de cada fabricante foi observado utilizando o microscópio eletrônico de varredura (MEV). A análise-estatística foi realizada utilizando o teste de análise de variância com um fator ANOVA e teste de Tukey, o nível de significância foi de 5%. O valor de resistência a fadiga cíclica do EDM diâmetro 25, conicidade .08 foi significantemente maior que todos os instrumentos testados (P<0.05). A LOG diâmetro 25, conicidade .06 mostrou maior resistência à fadiga cíclica que o GN diâmetro 25, conicidade .04; TS diâmetro 25, conicidade .06 (P<0.05). Não houve diferença significante entre os outros grupos. O teste torsional mostrou que PTG diâmetro 25, conicidade .08 obteve o maior valor de torque até a fratura de todos os instrumentos testados seguido por VB diâmetro 25, conicidade .06 e EDM diâmetro 25, conicidade .06 (P<0.05). O LOG diâmetro 25, conicidade .06 mostrou diferença significativa apenas com com GN diâmetro 25, conicidade .04 (P<0.05). Não houve diferença significativa entre os outros grupos (P>0.05). Em relação a deflexão angula, o GN diâmetro 25, conicidade .04; TS diâmetro 25, conicidade .06; HCM diâmetro 25, conicidade .06 e EDM diâmetro 25, conicidade .08 apresentou significantimente o maior valor até a fratura que os outros grupos (P<0.05). Nao foi encontrado diferença significativa entre PTG diâmetro 25, conicidade .08, LOG diâmetro 25, conicidade .06, e VB diâmetro 25, conicidade .06 (P<0.05). O EDM diâmetro 25, conicidade .08 apresentou a maior resistência a fadiga cíclica entre todos os instrumentos testados. Para o teste torsional, o PTG diâmetro 25, conicidade .08 apresentou o maior valor de torque e menor deflexão angular.

Title: Analysis of regional and club origin in the education of players playing the highest senior competition in the Czech Republic or the highest foreign competition in the period from 2010 to 2021. Objectives: Find out the participation of regions and clubs that are most involved in education into the Czech highest senior competition - I. Fortuna League or the highest foreign competition in the period from 2010 to 2021. Methods: Comparative historical research Results: The most effective region in the criterion of the length of the time time period of sports preparation of a player for the highest senior competition is the region Prague. The most effective club with the status of KA is AC Sparta Prague (577 years), the club with the status of SCM 1. FK Příbram (318 years), the club with the status of SpSM FK Frýdek Místek (57 years) and the club without status/assistance TJ Tatran Sedlčany (25 years). Clubs with amateur status ensure dominantly a higher number of first registrations in the FACR information system, however, in the U11 category there is a higher number of players registered in clubs with professional status. Keywords: Talent, education, representation, clubs, regions, 1. league

This work deals with information system designed to organize tournaments and leagues in e-sports. Its purpose is to propose changes in the information system of the organization. Another purpose also aims to select suitable systems and tournament leaderboards for implementation in the information system and system requirements include knowledge gained from the players. This work seeks the risks that exist in the current state of information system and proposes measures for them.

This thesis aims to present how the daily Sport, the web iSport, the sports section of MF Dnes and the website sport.idnes.cz reported on the coronavirus crisis in connection with the Fortuna League. To achieve the objectives of the thesis, quantitative content analysis is used. Three time periods are examined in the thesis, with each period chosen to cover an important period in the events related to the coronavirus crisis and the Fortuna League. The research part of the thesis analyses the articles published in each period, as well as examining mentions of clubs and the use of narratives. The results are compared both between periods and between media. The thesis also presents the Fortuna League as a competition, individual clubs and their history. At the same time, the thesis chronologically characterizes the key events of the coronavirus crisis in the Czech Republic. It also briefly presents recent research findings on sports journalism during the coronavirus crisis.

UV-LIGA is a microfabrication process realzed by material deposition through microfabricated molds. UV photolithography is conducted to pattern precise thick micro molds using UV light sensitive materials, mostly SU-8, and electroforming is performed to fabricate micro metallic structures defined by the micro molds. Therefore, UV-LIGA is a bottom-up in situ material-addition process. UV-LIGA has received broad attention recently than LIGA – a micro molding fabrication process using X-ray to pattern the micro molds. LIGA is an expansive and is limited in access. In comparing to LIGA, the UV-LIGA is a cost effective process, and is widely accessible and safe. Therefore, it has been extensively used for the fabrication of metallic micro-electro-mechanical-systems (MEMS). The motivation of this research was to study micro mechanical systems fabricated with nano-structured metallic materials via UV-LIGA process. Various micro mechanical systems with high-aspect-ratio and thick metallic structures have been developed and are presented in this desertation. A novel micro mechanical valve has been developed with nano-structured nickel realized with UV-LIGA fabrication technique. Robust compact valves are crucial for space applications where payload and rubstaness are critically concerned. Two types of large flow rate robust passive micro check valve arrays have been designed, fabricated and tested for robust hydraulic actuators. The first such micro valve developed employs nanostructured nickel as the valve flap and single-crystal silicon as the substrates to house inlet and outlet channels. The Nano-structured nickel valve flap was fabricated using the UV-LIGA process developed and the microchannels were fabricated by deep reactive etching (DRIE) method. The valves were designed to operate under a high pressure (>10MPa), able to operate at high frequencies (>10kHz) in cooperating with the PZT actuator to produce large flow rates (>10 cc/s). The fabricated microvalves weigh 0.2 gram, after packing with a novel designated valve stopper. The tested results showed that the micro valve was able to operate at up to 14kHz. This is a great difference in comparison to traditional mechanical valves whose operations are limited to 500 Hz or less. The advantages of micro machined valves attribute to the scaling laws. The second type of micro mechanical valves developed is a in situ assembled solid metallic (nickel) valves. Both the valve substrates for inlet and outlet channels and the valve flap, as well as the valve stopper were made by nickel through a UV-LIGA fabrication process developed. Continuous multiple micro molds fabrication and molding processes were performed. Final micro mechanical valves were received after removing the micro molds used to define the strutures. There is no any additional machining process, such as cutting or packaging. The alignment for laminated fabrication was realized under microscope, therefore it is a highly precise in situ fabrication process. Testing results show the valve has a forward flow rate of19 cc/s under a pressure difference of 90 psi. The backward flow rate of 0.023 cc/s, which is negligible (0.13%). Nano-structured nickel has also been used to develop laminated (sandwiched) micro cryogenic heater exchanger with the UV-LIGA process. Even though nickel is apparently not a good thermal conductor at room temperature, it is a good conductor at cryogentic temerpature since its thermal conductivity increases to 1250 W/k·m at 77K. Micro patterned SU-8 molds and electroformed nickel have been developed to realize the sandwiched heat exchanger. The SU-8 mold (200mm x 200mm x50mm) array was successfully removed after completing the nickel electroforming. The second layer of patterned SU-8 layer (200mm x 200mm x50mm, as a thermal insulating layer) was patterned and aligned on the top of the electroformed nickel structure to form the laminated (sandwiched) micro heat exchanger. The fabricated sandwiched structure can withstand cryogenic temperature (77K) without any damages (cracks or delaminations). A study on nanocomposite for micro mechanical systems using UV-LIGA compatible electroforming process has been performed. Single-walled carbon nanotubes (SWNTs) have been proven excellent mechanical properties and thermal conductive properties, such as high strength and elastic modulus, negative coefficient of thermal expansion (CTE) and a high thermal conductivity. These properties make SWNT an excellent reinforcement in nanocomposite for various applications. However, there has been a challenge of utilizing SWNTs for engineering applications due to difficulties in quality control and handling – too small (1-2nm in diameter). A novel copper/SWNT nanocomposite has been developed during this dissertational research. The goal of this research was to develop a heat spreader for high power electronics (HPE). Semiconductors for HPE, such as AlGaN/GaN high electron mobility transistors grown on SiC dies have a typical CTE about 4~6x10-6/k while most metallic heat spreaders such as copper have a CTE of more than 10x10-6/k. The SWNTs were successfully dispersed in the copper matrix to form the SWNT/Cu nano composite. The tested composite density is about 7.54 g/cm3, which indicating the SWNT volumetric fraction of 18%. SEM pictures show copper univformly coated on SWNT (worm-shaped structure). The measured CTE of the nanocomposite is 4.7 x 10-6/°C, perfectly matching that of SiC die (3.8 x 10-6/°C). The thermal conductivity derived by Wiedemann-Franz law after measuring composit's electrical conductivity, is 588 W/m-K, which is 40% better than that of pure copper. These properties are extremely important for the heat spreader/exchanger to remove the heat from HPE devices (SiC dies). Meanwhile, the matched CTE will reduce the resulted stress in the interface to prevent delaminations. Therefore, the naocomposite developed will be an excellent replacement material for the CuMo currently used in high power radar, and other HPE devices under developing. The mechanical performance and reliability of micro mechanical devices are critical for their application. In order to validate the design & simulation results, a direct (tensile) test method was developed to test the mechanical properties of the materials involved in this research, including nickel and SU-8. Micro machined specimens were fabricated and tested on a MTS Tytron Micro Force Tester with specially designed gripers. The tested fracture strength of nanostructured nickel is 900±70 MPa and of 50MPa for SU-8, resepctively which are much higher than published values.