This work comprises different approaches for the efficiency enhancement of white organic light-emitting diodes (OLEDs). In particular, diffusion and transfer processes of excited singlet and triplet states are investigated. Generation of white light is realized by using the so-called triplet harvesting method where the otherwise nonradiatively decaying triplets of a blue fluorescent emitter are transferred to a highly efficient phosphorescent emitter and result in additional emission at lower energies. Triplet harvesting significantly increases the internal quantum efficiency in OLEDs. First, the well-known blue emitter 4P-NPD is investigated as model case. Using time-resolved spectroscopy, triplet harvesting by a yellow and red phosphorescent emitter, respectively is directly proven. However, triplet harvesting by a green emitter is not possible due to the low triplet energy of 4P-NPD. Using quantum chemical calculations, two new emitter molecules, 8M-4P-NPD and 8M-4P-FPD, are synthesized with the aim to rise the triplet energy. Their properties and their ability to facilitate triplet harvesting by a green emitter are studied. For the first time, a white triplet harvesting OLED is demonstrated where triplet harvesting occurs directly from a blue emitter to a green and a red emitter. Furthermore, an additional singlet transfer is observed in the triplet harvesting OLEDs under investigation. Using the phosphorescent emitter as singlet sensor, this effect allows the determination of the singlet diffusion length in 4P-NPD. By varying the distance between singlet generation zone and singlet sensor, a singlet diffusion length of 4.6 nm is found. One further approach to increase the efficiency is the optimization of a tandem OLED which comprises two single OLED units stacked on top of each other. At a luminance of 1,000 cd/m², the white tandem OLED shows an external quantum efficiency of 25%, a luminous efficacy of 33 lm/W, a color rendering index (CRI) of 62, and Commission Internationale de l’Eclairage (CIE) color coordinates of (0.53/0.43). These efficiencies are comparable to state-of-the-art efficiencies of white OLEDs. Finally, the highly efficient white tandem structure is applied on an alternative electrode consisting of flattened silver nanowires. In comparison to the conventional OLED with indium-tin oxide (ITO) electrode, this OLED shows similarly high efficiencies as well as a superior color stability in terms of viewing angles. The color stability can be assigned to the light scattering properties of the nanowires. The OLED with silver nanowire electrode shows efficiencies of 24% and 30 lm/W at 1,000 cd/m² with a CRI of 69 and CIE coordinates of (0.49/0.47). / In dieser Arbeit werden verschiedene Ansätze zur Effizienzsteigerung in weißen organischen lichtemittierenden Dioden (OLEDs) erforscht. Hierfür werden im Besonderen Diffusions- und Transferprozesse von angeregten Singulett- und Triplettzuständen untersucht. Zur Erzeugung von weißem Licht wird die sogenannte “triplet harvesting” Methode verwendet, bei der die sonst nicht zur Emission beitragenden Triplettzustände eines fluoreszenten blauen Emitters auf einen hocheffizienten phosphoreszenten Emitter übertragen werden. Dieser liefert dann zusätzliche Emission im niederenergetischen Spektralbereich. Durch triplet harvesting kann die interne Quantenausbeute in OLEDs beträchtlich gesteigert werden. Zunächst wird der bekannte blaue Emitter 4P-NPD als Modellbeispiel untersucht. Mittels zeitlich aufgelöster Spektroskopie kann triplet harvesting auf einen gelben bzw. roten Emitter direkt nachgewiesen werden. Allerdings ist auf Grund der niedrigen Triplettenergie triplet harvesting auf einen grünen Emitter nicht möglich. In Anbetracht dieser Tatsache werden unter Zuhilfenahme quantenchemischer Betrachtungen zwei neue Emittermoleküle, 8M-4P-NPD und 8M-4P-FPD, synthetisiert und auf ihre Eigenschaften und ihre Eignung für triplet harvesting untersucht. Dabei wird zum ersten Mal eine weiße OLED realisiert, in der triplet harvesting von einem blauen Emitter direkt auf einen grünen und einen roten Emitter erfolgt. Des Weiteren wird bei den untersuchten triplet harvesting OLEDs ein zusätzlicher Singulettübertrag auf den phosphoreszenten Emitter beobachtet. Dieser Effekt wird zur Bestimmung der Singulettdiffusionslänge in 4P-NPD genutzt. Der phosphoreszente Emitter dient dabei als Singulettsensor. Über eine Variation des Abstands zwischen Singulettgenerationszone und Sensor wird eine Singulettdiffusionslänge von 4,6 nm bestimmt. Ein weiterer Ansatz zur Effizienzsteigerung besteht in der Optimierung einer aus zwei OLEDs zusammengesetzten Tandem OLED. Bei einer Leuchtdichte von 1000 cd/m² erzielt diese weiße Tandem OLED eine externe Quanteneffizienz von 25% und eine Leistungseffizienz von 33 lm/W mit einem Farbwiedergabeindex (CRI) von 62 und Commission Internationale de l’Eclairage (CIE) Farbkoordinaten von (0,53/0,43). Diese Effizienzen sind vergleichbar mit dem aktuellen Forschungsstand weißer OLEDs. Schließlich wird diese hocheffiziente weiße Tandemstruktur auf eine alternative Elektrode bestehend aus flachgedrückten Silbernanodrähten aufgebracht. Im Vergleich zur konventionellen OLED mit Indiumzinnoxid (ITO) Elektrode erreicht diese ähnlich hohe Effizienzen sowie eine verbesserte Farbstabilität bezüglich des Betrachtungswinkels, was auf die Streueigenschaften der Nanodrähte zurückgeführt werden kann. Bei einer Leuchtdichte von 1000 cd/m² zeigt die OLED mit Silbernanodrahtelektrode Effizienzen von 24% und 30 lm/W bei einem CRI von 69 und CIE Koordinaten von (0,49/0,47).

In last decade, white light emitting diodes(LEDs) have become used widely from traditional indicator to general illumination. The increase of its power is the key improving issue. The current light efficiency of white LED about 30%. In other words ,more than 70% of the input electrical energy will be generated in the form of heat. So, how to get rid of the heat damage in high power LED is a severe problem. The finite element analysis is employed to simulate high power white LEDs temperature distribution and thermal stress distributions caused by the dissipated heat. The effects of package parameters, i.e. die attach, solder material, solder thickness, and chip substrate, on the temperature and thermal stress distributions on high power LED packages are simulated and studied in this thesis. A comparison between the 40mil single chip package and the chip on board(CoB) package has also been executed in this study. Simulated results indicate that the highest power of a single 40mil chip package is 7watt. The thermal stress distribution , i.e. the peak value of local thermal stress is over its yield strength, is occurred as the power up to 7watt. Numerical results also reveal that the appropriate fin design can improve the heat dissipation significantly in high power LED package.

In this thesis, we design electrode shape of light emitter diode (LED) to help the current diffusing uniformly. The purpose of the uniform current is to avoid the waste heat from the devices and enhance the efficiency of active region. The LED samples adopted in this study are GaN base materials grown on sapphire. The P-N electrodes must be processed on the same side since the poor conductivity of sapphire. The same side P-N electrode will results in current crowding phenomena. We design special electrode shapes to make the current diffuse uniformly and reduce the current crowding phenomena. First, we use COMSOL simulation software to simulate the current spreading between the electrodes. We adopt the same parameters from the reference papers to confirm the reliabilities of the simulation. Then we simulate several electrode shapes with highly uniform current spreading. Second, we use the simulation results to fabricate electrode on chips. The first set is LED without transparent conductive layer. This set is to confirm whether the fabrication processes is feasible and adjust the simulation parameters at the same time. The second set is LED with transparent conductive layer. The experimental emission intensity has deviation from the simulation results. We deduce the emission intensities from smaller LED chip size will have great influence on illumination surface. The third set is electrodes fabricated on large size LED chip. The electrode patterns successfully enhance the uniformity of current spreading, and enhance the output light intensity of 21%. The current density distribution trend from simulation is matched with the illumination intensities.

This research plans the power capacities of the obstacle lighting on the power transmission towers, which are located in the areas where the utility cannot reach. The obstacle lighting is formed by light emitting diodes (LEDs), which are powered mainly by solar cells and subordinately by rechargeable batteries. The solar cells charge the batteries during the sunny daytime with plenty sunlight. When the sunlight is insufficient and the obstacle lamp is turned on, batteries and solar cells supply the obstacle lighting simultaneously. The power capacities of the solar cells and batteries are designated to keep the obstacle lighting system uninterruptible either under the drastic weather variation or a long period of insufficient sunlight. Under the specified operation rules of the obstacle lighting, a more economical and precise method is proposed for planning the power capacities of solar cells and batteries based on the weather data from Central Weather Bureau in recent 6 years following. The power planning method is implemented in the areas of Kaohsiung, Chiayi and Ali mountain to demonstrate the feasibility and the accuracy in reality.

In this thesis, we use self-assembled nano metal particles as a dry etching mask to from nanopillars. The nanopillars integrated with traditional light-emitting diode (LED) p-type GaN surface is designed to increase the light extraction efficiency. The initial fabrication process adopted in this study is using 100nm SiO2 as thermal aggregation layer. The poor thermal conductivity of SiO2 material will help to accumulate heat on the surface. Then, 10nm Ni thin film is deposited on the SiO2, and rapid annealed at 900oC (working pressure of 1~3¡Ñ10-6 Torr). The Ni nanospheres are prepared to integrate with LED chip processes. We use the etching times (pillar heights) as experimental parameters to study the degree of light extraction efficiency. Traditional right angle branch electrode samples of as grown, 20, 30, 40 sec etching time are analyzed by LI curve measurement. Under 20mA injection current, samples with 20, 30, 40 sec etching times have better light extraction than as grown, an increase of 6.54%, 3.27%, 1.63%, respectively. The experimental results reveal that self-assembled nano metal particles as a dry etching mask on the p-type GaN LED surface can increase the light extraction efficiency.

ABSTRACT Optoelectronics of polymer light emitting diode (LED) depends significantly on polymer molecular structure and charge conjugation. This study focused on the optoelectronics of freestanding films and LEDs of a colinear, fully conjugated heterocyclic aromatic rigid-rod polymer (PBT) and its mixtures with a partially conjugated coil-like polymer (Pbi). A deuterated PBTd4 was also mixed with a fully conjugated coil-like polymer (ABPBI) for UV-Vis absorption spectrum, photoluminescence (PL), diodic current-voltage response, and electroluminescence (EL). Rigid-rod PBT was only soluble in strong protic acid. PBT films were processed using methanesulfonic acid. PBT free-standing films showed maximum absorptions at 468 nm and 640 nm; PBTd4 having all hydrogen atoms on the phenylene moiety substituted by deuterium retaining same electron orbitals thus showed same absorption and PL spectra. It was likewise for the PBTd4 and ABPBI mixtures at ABPBI concentrations of 1 % and 10 %. For mixtures of PBT and Pbi, the absorption spectra indicated super- position of individual optical absorption response and no energy transfer. However, PL spectra showed a blue shift with increasing Pbi content. This was attribed for PBT rod-like configuration, or PBT aggregation perturbed by mixing with Pbi. Monolayer LED of Al/PBT/ITO and Al/Pbi/ITO yielded a threshold voltage of 4 V. When PBT/Pbi mixtures of 75/25, 50/50, 25/75, were used as the light emitting layer, the threshold voltage altered to 10 V, 7 V and 17 V, respectively. This threshold voltage deviation from 4 V is due mainly to difference in layer thickness, or phase separation affecting the tunneling effect. To enhance LED stability, an Ag layer was evaporated onto the Al electron injection electrode. For Ag/Al/PBT/ITO devices and mixed PBT/Pbi (75/25,50/50,25/75) devices, the maximum EL wavelength exhibited no systematic change at 753 nm, 714 nm, 727 nm, and 697 nm, respectively, due to using different bias voltage.

This paper tries to explore the phosphor optical characteristics through reliability tests using white light emitting diodes (WLEDs) with a high color rendering index (CRI ,Ra¡Ö90). Based on light mixing principles and considering the high CRI, three color-coded powders were mixed separately with silicone into a phosphor, and then bottomed with blue chips into WLEDs. The three powders were oxide nitride (red), YAG (yellow), and silicate (green). Two kinds of samples were fabricated ¡V phosphor and emitters similar to commercial products. Both cool-white (CCT=5650~7000K, lumen efficiency¡Ö60 lum/w.) and warm-white (CCT=2850~3250K, lumen efficiency¡Ö50 lum/w.) samples passed the Bin Code distribution process and brightness measurement. The results indicate better lumen efficiency than previously published research. After the three kinds of mono-colored phosphors were created, .we implemented the reliability test in which three CREE standards were chosen. These standards were (1) high temperature with high humidity test (60¢J , 90% humidity) in operating and non-operating condition; (2) thermal shock test (-40¢J ~125¢J ); (3) life time test. The thermal shock test showed the decaying power of intensity for red, yellow, and green phosphors were 11.7%, 17.5%, and 19.3% respectively. These results demonstrate that the red phosphor has the best thermal resistance. However, after the high temperature with high humidity tests, the decaying power of intensity for red,yellow, and green phosphor were 15.7%, 10.1% and 6.4% correspondingly. These results show that the green phosphor has best aqua resistance. In the life time test of emitters, the decaying power of intensity for the cool-white emitter was 3.2%, while the warm-white emitter showed 4.2%. As such, cool-white emitters were concluded to have better reliability than warm-white emitters.

The piezo-phototronics effect is the three way coupling of semiconductor properties, photonics and piezoelectricity in the same material. Research on piezo-phototronics effect has illustrated its application on various Zinc Oxide (ZnO) nanowire based devices, yet a systematical study with comprehensive theoretical model is still missing. Here we have designed experiments on wider variety of materials to investigate the mechanism of the piezo-phototronics effect, and then built up a theoretical model for more thorough understanding. Experimental results are shown for Cadmium Sulfide (CdS) photodetectors for visible light detection, inorganic/organic hybrid Light Emitting Diodes (LEDs) and LED arrays, and it is demonstrated that strain can significantly tune the performance of these optoelectronic devices. Theoretical methodologies are proposed for Metal-Semiconductor-Metal (MSM) structure and p-n junctions, including analytical solutions and Finite Element Method (FEM) simulations. For Schottky contacts in photodetectors, barrier height change is determined as the main reason for the effect, and an exponential relationship between applied external strain and the device current is discovered, and is qualitatively confirmed from experimental results. For p-n junctions in LEDs, change in size of depletion region under strain is credited for the current change, and a charge channel is predicted for large strain, which gives explanation for the observed gigantic enhancement of light emission efficiency in experiments.

Metal/organic/indium tin oxide (ITO) structures, including OLEDs, are demonstrated to contain multiple nonvolatile conductance states that can be programmed by the application of an external bias above a certain threshold voltage (Vth). These conductance states are stable and in turn can be probed by the use of a bias lower in value than Vth. The unbiased retention time of states is greater than several weeks, and more than 48,000 write-read-rewrite-read cycles have been performed with minimal degradation. It is found that the programming of a continuum of conductance states is possible, and techniques to do so are outlined. The electrical conductivity of the highest and lowest states can differ by six orders of magnitude. Switching speeds below 50 ns are shown, resulting in an energy requirement of about 100 pJ to switch from one conductance state to another. The memory phenomenon is shown to be influenced by the active layer thickness and anode/surface roughness while temperature dependence is limited. The electrical characteristics of these devices are consistent with metal diffusion or filament phenomena found in metal-insulator-metal structures, suggesting a possible mechanism by which the states are stored.Electroluminescent devices employing several new organic-inorganic lumophore-functionalized macromolecules are presented. In this study, macromolecules incorporating several lumophores covalently bonded to the vertices of a cubical core structure based on Polyhedral Oligomeric Silsesquioxane (POSS) in multiple configurations are implemented as light-emitting centers. The hole-transporting polymer poly(N-vinylcarbazole) (PVK) and electron-transporting additive 2-(4-biphenylyl)-5-(4-tert-butylphenyl)1,3,4-oxadiazole (PBD) are used as a two-part host to enhance the carrier transport in these simple solution-processed single-layer devices. A study of energy transfer in several systems is carried out to understand the requirements needed to create white-light emission from a single macromolecule. A single macromolecule incorporating twenty-one blue and one yellow lumophore is shown to exhibit field-independent stable white-light electroluminescence with Commission Internationale de l'Eclairage (CIE) coordinates of (0.31, 0.37). An external quantum efficiency of 0.55 percent and a maximum brightness of 1600 cd/m2 are attained with simple solution-processed single-layer devices. High solubility and ease of purification give these macromolecule white-light emitters advantages over their small molecule and polymeric type counterparts.

White LEDs (Light Emitting Diodes) in Visible Light Communication (VLC) is an emerging technology that is being researched so it can eventually be used for common communications systems. LEDs have a number of advantages, one of which is long life expectancy. However, like many emerging technologies, VLC has many technical issues that need to be addressed. We proposed an optical indoor wireless communication system that used white LEDs like plug-in devices. We developed a practical implementation of VLC and demonstrated it experimentally. In particular we focused on designing a prototype of VLC that can be used without having to make major changes to the present infrastructure with two types of protocol — namely RS-232 and USB — for data transmission.