The objective of this dissertation is to develop key components of a CMOS heterodyne millimeter-wave receiver front end. Robust designs are necessary to overcome PVT variations as well as modeling inaccuracies, while with minimum power consumption overhead to facilitate low-power radio for portable applications. Heterodyne receiver topology is adopted because of its robust performances at millimeter-wave frequencies. Device models for both passive and active devices are developed and used in the circuit designs in this dissertation. Two low-noise amplifiers (LNAs) are developed in this dissertation. The first LNA features a proposed temperature-compensation biasing technique, which confines the gain variation within 5 dB for temperature variation from -5 to 85 Celsius degree. The measured gain and NF are 21 and 6.5 dB, respectively, for 49-mW power dissipation. The second LNA reveals a design technique to tolerate a low-accuracy model at millimeter-wave frequencies. Both LNAs provide full coverage of the FCC 60-GHz band (57-64 GHz). For the frequency generation circuits, both the IF QVCO and mm-wave VCO are investigated. The inherent bimodal oscillation of QVCOs is analyzed and, for the first time, a systematic measurement technique is proposed to intentionally control the oscillation mode. This technique is further utilized to extend the tuning range of the QVCO, which possesses dual tuning curves without penalty on phase noise. The measurement results of a 13-GHz QVCO in 90-nm CMOS reveals a 21.4% tuning range for continuously tuning from 11.7 to 14.5 GHz. The measured phase noise is -108 dBc/Hz at 1 MHz offset with a core power consumption of 10.8 mW. A millimeter-wave VCO is designed and fabricated in 65-nm CMOS. The VCO is fully characterized under voltage stress to examine the hot-carrier injection effects affecting the performance of a millimeter-wave VCO. The 41.6-47.4 GHz VCO is further integrated into a millimeter-wave down converter. The power-hungry buffer amplifiers are neglected by proper floor planning. Conversion loss of 1.4 dB is obtained with total power consumption of 72.5 mW. Lastly, a power management system consisting of low-dropout (LDO) regulators is designed and integrated in a 90-nm CMOS millimeter-wave transceiver to provide stable and low-noise supply voltages. Voltage variation issues are alleviated by the LDOs.

Microwave-Assisted Thermolysis of ortho-Substituted Aroylsilanes Marc Tremblay Master of Science Department of Chemistry University of Toronto 2008 The microwave-assisted thermolysis of ortho-substituted aroylsilanes has been investigated. When irradiated at 250ºC in DMSO or o‑dichlorobenzene for 10 minutes, aroylsilanes form siloxycarbenes that react following different pathways depending on the solvent and the structure of the starting material. It is shown that in the case of substrates having an O‑allyl or an O‑propargyl chain ortho to the acylsilane, cycloaddition occurs followed by a cascade ring opening to give respectively chroman‑4-one and chromen‑4-one derivatives in up to 66% yield. Among the major competitive pathways were the insertion of the siloxycarbene into allylic C–H bonds and decomposition of the acylsilane group to the corresponding aldehyde, followed by Claisen rearrangement.

Microwave-Assisted Thermolysis of ortho-Substituted Aroylsilanes Marc Tremblay Master of Science Department of Chemistry University of Toronto 2008 The microwave-assisted thermolysis of ortho-substituted aroylsilanes has been investigated. When irradiated at 250ºC in DMSO or o‑dichlorobenzene for 10 minutes, aroylsilanes form siloxycarbenes that react following different pathways depending on the solvent and the structure of the starting material. It is shown that in the case of substrates having an O‑allyl or an O‑propargyl chain ortho to the acylsilane, cycloaddition occurs followed by a cascade ring opening to give respectively chroman‑4-one and chromen‑4-one derivatives in up to 66% yield. Among the major competitive pathways were the insertion of the siloxycarbene into allylic C–H bonds and decomposition of the acylsilane group to the corresponding aldehyde, followed by Claisen rearrangement.

Se discute la guía dieléctrica en banda invertida como modificación capaz de aumentar el factor de calidad de la guía dieléctrica rectangular. En su configuración abierta se emplea para su estudio el método de la constante dieléctrica efectiva; se optimiza la geometría para conseguir el mayor ancho de banda posible y se discute la posibilidad de naturaleza espuerea para una parte de los modos encontrados. Se comprueba que el sistema de excitación clásico para guías dieléctricas no resulta valido para la guía en banda invertida y se optimiza un sistema de tipo cornete. Mediante un sistema de sonda móvil se mide la constante de propagación en la guía obteniéndose un buen acuerdo con las predicciones teóricas. Se estudia la guía dieléctrica cerrada en una caja mediante el método de Schelkunoff comprobándose la existencia de modos EH. / The inverted band dielectric waveguide is proposed as an alternative to the classical open dielectric waveguide, providing a higher quality factor. The dielectric effective constant method is used to study the open waveguide. In order to get the highest bandwith, the geometry is optimised, finding not real modes in the waveguide. It has been necessary to use a new excitation method of waveguide using a horn as transition. The measurement of the propagation constant has been made by means of an electric probe. The agreement with the theoretical predictions is very good. Finally the closed guide is studied by the Schelkunoff's method: modes EH were observed.

Accurate knowledge of the centimeter- and millimeter-wavelength absorptivity of ammonia is necessary for the interpretation of the emission spectra of the jovian planets. The objective of this research has been to advance the understanding of the centimeter- and millimeter-wavelength opacity spectra of ammonia under jovian conditions using a combination of laboratory measurements and theoretical formulations. As part of this research, over 1000 laboratory measurements of the 2-4 mm-wavelength properties of ammonia under simulated upper and middle tropospheric conditions of the jovian planets, and approximately 1200 laboratory measurements of the 5-20 cm-wavelength properties of ammonia under simulated deep tropospheric conditions of the jovian planets have been performed. Using these and pre-existing measurements, a consistent mathematical formalism has been developed to reconcile the centimeter- and millimeter-wavelength opacity spectra of ammonia. This formalism can be used to estimate the opacity of ammonia in a hydrogen/helium atmosphere in the centimeter-wavelength range at pressures up to 100 bar and temperatures in the 200 to 500 K range and in the millimeter-wavelength range at pressures up to 3 bar and temperatures in the 200 to 300 K range. In addition, a preliminary investigation of the influence of water vapor on the centimeter-wavelength ammonia absorptivity spectra has been conducted. This work addresses the areas of high-sensitivity centimeter- and millimeter-wavelength laboratory measurements, and planetary science, and contributes to the body of knowledge that provides clues into the origin of our solar system. The laboratory measurements and the model developed as part of this doctoral research work can be used for interpreting the emission spectra of jovian atmospheres obtained from ground-based and spacecraft-based observations. The results of the high-pressure ammonia opacity measurements will also be used to support the interpretation of the microwave radiometer (MWR) measurements on board the NASA Juno spacecraft at Jupiter.

Made available in DSpace on 2014-06-11T19:28:38Z (GMT). No. of bitstreams: 0 Previous issue date: 2007-03-26Bitstream added on 2014-06-13T19:16:49Z : No. of bitstreams: 1 sanita_pv_me_arafo.pdf: 1236296 bytes, checksum: 793fd4710489b2253297ebbc15835736 (MD5) / Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / A estomatite protética associada à Candida é a forma mais comum de candidíase oral e também uma das infecções oportunistas mais encontradas em pacientes infectados por HIV. Atualmente, a desinfecção de próteses totais através da irradiação por microondas tem sido recomendada para tratamento e prevenção da estomatite protética, tanto em indivíduos saudáveis, quanto em pacientes imunocomprometidos. O presente estudo avaliou a efetividade da irradiação por microondas na desinfecção de próteses totais simuladas contaminadas com 5 diferentes espécies do microorganismo Candida (C. albicans, C. glabrata, C. dubliniensis, C. tropicalis e C. krusei) isoladas de culturas padrão e de pacientes HIV positivo. Para isso, próteses totais simuladas foram confeccionadas, esterilizadas por meio de óxido de etileno e individualmente inoculadas com os microorganismos avaliados. Após o período de incubação (48 horas a 37°C), as próteses foram submetidas à irradiação por microondas a 650W durante 3 minutos. Próteses totais não irradiadas foram utilizadas como controle positivo. A seguir, uma alíquota de 25 æL da solução resultante das diluições seriadas de 10-1 a 10-4 foi semeada em placas de Petri em duplicata e todas as placas foram incubadas por 48 horas a 37°C. As colônias foram quantificadas em ufc/mL. Para verificar a efetividade da desinfecção por microondas a longo prazo, as próteses totais irradiadas foram incubadas a 37°C por 7 dias. Os resultados obtidos foram analisados estatisticamente pelos testes de ANOVA e de Tukey (a=0.05). As próteses totais contaminadas com todas as espécies de Candida avaliadas demonstraram esterilização após irradiação por microondas durante 3 minutos a 650W. Todas as próteses do grupo controle positivo demonstraram crescimento microbiológico após incubação nas placas de Petri. / The most common form of oral candidiasis is Candida-associated denture stomatitis. Oral candidiasis is also a frequent manifestation of HIV infection. Microwave disinfection of complete dentures has been recommended to treat and prevent denture stomatitis in non-immune compromised patients. The present study evaluated the effectiveness of microwave irradiation on the disinfection of simulated complete dentures inoculated with ATCC and HIV isolates of 5 species of Candida (C. albicans, C. glabrata, C. dubliniensis, C. tropicalis and C. krusei). Simulated complete dentures were made, sterilized and individually inoculated with the tested microorganisms. After incubation for 48 hours at 37°C, dentures were submitted to microwave irradiation (650W for 3 minutes). Non-irradiated dentures were used as positive controls. Replicate aliquots of suspensions were plated at dilutions 10-1-10-4 and incubated for 48 hours at 37°C. Colonies counts (cfu/mL) of each plate were quantified. To verify the long-term effectiveness of microwave disinfection, dentures were incubated at 37°C for 7 days. Data were analyzed with two-way ANOVA and Tukey HSD tests (a=0.05). The results indicated that complete dentures contaminated with all Candida yeasts showed sterilization after microwave irradiation for 3 minutes at 650W. All control dentures showed microbial growth on the plates. The cfu/mL for C. glabrata was significantly higher than those of C. albicans, C. dubliniensis and C. tropicalis whereas the cfu/mL for C. krusei was significantly lower. The cfu/mL for clinical isolates was significantly higher than those of ATCC yeasts. Microwave irradiation for 3 minutes at 650W resulted in sterilization of complete dentures contaminated with the 5 species of Candida isolated from HIV-infected patients.

Made available in DSpace on 2014-06-11T19:28:38Z (GMT). No. of bitstreams: 0 Previous issue date: 2011-03-28Bitstream added on 2014-06-13T20:18:32Z : No. of bitstreams: 1 altieri_kt_me_arafo.pdf: 598917 bytes, checksum: 3b01564a77c1be4471454056881b7028 (MD5) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / Infecções causadas por bactérias resistentes a antibióticos são consideradas causa principal de mortalidade entre indivíduos imunocomprometidos e aproximadamente 50 % destas infecções tem sido relacionadas ao Staphylococcus aureus resistente à meticilina (MRSA). Estes microrganismos, quando presentes no biofilme das próteses dentarias, podem se dispersar nas secreções salivares e se disseminar pelo trato respiratório, causando pneumonia aspirativa. Assim, o presente estudo comparou a efetividade do hipoclorito de sódio a 1 %, digluconato de clorexidina a 2 % e irradiação por micro-ondas na desinfecção de próteses totais e corpos-de-prova circulares de resina acrílica para base de prótese (10 x 2 mm) contaminados com MRSA. Para isso, 36 próteses totais simuladas e 36 corpos-de-prova circulares foram confeccionados, esterilizados, inoculados com MRSA (107 ufc/mL) e incubados a 37 °C (por 24 e 48 h, respectivamente). Após incubação, próteses totais e corpos-de-prova foram distribuídos em 4 grupos de estudo (n=9): GC - não foi realizado nenhum método de desinfecção; GH - foi realizada a imersão em solução de hipoclorito de sódio a 1 % por 10 min; GCl -foi realizada a imersão em solução de digluconato de clorexidina a 2 % por 10 min; GM - foi realizada a desinfecção por irradiação em forno de micro-ondas a 650 W por 3 min. A efetividade dos procedimentos de desinfecção foi avaliada por meio de quantificação de colônias viáveis e da viabilidade celular. Para a quantificação de colônias viáveis, alíquotas de 25 μL da solução resultante das diluições seriadas (10-3 a 10-6 para GC e 100 a 10-3 para os grupos experimentais) foram semeadas em placas de Petri em duplicata e todas as placas foram incubadas por 48 h a 37 °C. As colônias foram quantificadas em ufc/mL. Para verificar a efetividade da desinfecção por micro-ondas em longo prazo... / Infections caused by antibiotic-resistant bacteria have been recognized as a predominant risk factor for mortality in elderly patients and approximately 50 % of these infections have been related to methicillin-resistant Staphylococcus aureus (MRSA). This microorganism, when present in the denture biofilm, can be released into the oral fluids and aspirated into the lower respiratory tract, thus causing infections such as aspiration pneumonia. The present study compared the efficacy of 1 % sodium hypochlorite, 2 % chlorhexidine gluconate, and microwave irradiation in disinfecting simulated complete dentures and circular specimens of acrylic resin denture base material (10 x 2 mm) contaminated with MRSA. Thirty-six dentures and 36 specimens were made, sterilized, inoculated with MRSA (107 cfu/mL), and incubated at 37 °C (for 24 and 48 h, respectively). After incubation, dentures and specimens were divided into 4 groups of study (n=9): PC - positive control, consisting of dentures and specimens not disinfected; HY - soaking in 1 % sodium hypochlorite solution for 10 min; CHL - soaking in 2 % chlorhexidine gluconate solution for 10 min; and MW - irradiating by microwave for 3 min at 650W. The effectiveness of the disinfection procedures was assessed cell viability (quantification of viable cells and XTT reduction method). For quantification procedures, aliquots of suspensions were plated at dilutions (10-3 to 10-6 for PC and 100 to 10-3 for experimental groups) and incubated (37 °C/48 h). Colonies counts (cfu/mL) were quantified. Dentures disinfected were also incubated at 37 °C for 7 days to verify the long-term effectiveness of disinfection. The viability of cells in each group of specimens was evaluated by XTT reduction method. The results showed that all dentures and specimens from the PC groups showed substantial microbial growth. No evidence of microbial growth was observed... (Complete abstract click electronic access below)

Made available in DSpace on 2014-12-17T14:06:58Z (GMT). No. of bitstreams: 1 WalquiriaJS_DISSERT_PACIAL.pdf: 740304 bytes, checksum: 3d1d601a3873230ed2af2ce67496fdf5 (MD5) Previous issue date: 2011-07-21 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / The development and study of detectors sensitive to flammable combustible and toxic gases at low cost is a crucial technology challenge to enable marketable versions to the market in general. Solid state sensors are attractive for commercial purposes by the strength and lifetime, because it isn t consumed in the reaction with the gas. In parallel, the use of synthesis techniques more viable for the applicability on an industrial scale are more attractive to produce commercial products. In this context ceramics with spinel structure were obtained by microwave-assisted combustion for application to flammable fuel gas detectors. Additionally, alternatives organic-reducers were employed to study the influence of those in the synthesis process and the differences in performance and properties of the powders obtained. The organic- reducers were characterized by Thermogravimetry (TG) and Derivative Thermogravimetry (DTG). After synthesis, the samples were heat treated and characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), analysis by specific area by BET Method and Scanning Electron Microscopy (SEM). Quantification of phases and structural parameters were carried through Rietveld method. The methodology was effective to obtain Ni-Mn mixed oxides. The fuels influenced in obtaining spinel phase and morphology of the samples, however samples calcined at 950 ?C there is just the spinel phase in the material regardless of the organic-reducer. Therefore, differences in performance are expected in technological applications when sample equal in phase but with different morphologies are tested / O desenvolvimento e estudo de detectores sens?veis a gases combust?veis inflam?veis e t?xicos de baixo custo ? um desafio tecnol?gico determinante para possibilitar vers?es comercializ?veis ao mercado em geral. Sensores no estado s?lido s?o atrativos para fins comerciais pela robustez e tempo de vida, uma vez que n?o s?o consumidos durante o processo de rea??o com o g?s. Paralelamente, o uso de t?cnicas de s?ntese mais vi?veis pela aplicabilidade em escala industrial s?o mais atrativas para obten??o de produtos comerciais. Dentro desse contexto foram obtidos materiais cer?micos com estrutura espin?lio via combust?o assistida por microondas, visando aplica??o em detectores de gases combust?veis inflam?veis. Adicionalmente foram empregados direcionadores-org?nicos alternativos para estudo da influ?ncia dos mesmos no processo de s?ntese e nas diferen?as nas propriedades e desempenho dos p?s obtidos. Os direcionadores-org?nicos foram caracterizados por Termogravimetria (TG). Ap?s a s?ntese, as amostras foram tratadas termicamente e caracterizadas por Espectroscopia de absor??o na regi?o do infravermelho com Transformada de Fourier (FTIR), Difra??o de Raios X (DRX), Medidas de ?rea espec?fica por BET e Microscopia Eletr?nica de Varredura (MEV). A quantifica??o de fases e a determina??o de par?metros estruturais foram determinados por refinamento atrav?s do M?todo Rietveld. A metodologia empregada foi eficaz para obten??o de ?xidos mistos Ni-Mn. Os combust?veis utilizados influenciaram na obten??o da fase espin?lio e na morfologia das amostras, sendo que as amostras calcinadas a 950?C s?o monof?sicas independentemente do direcionador. Logo, diferen?as de desempenho s?o esperadas em aplica??es tecnol?gicas quando amostras iguais em fase mas com diferentes morfologias s?o testadas

Made available in DSpace on 2014-12-17T14:07:05Z (GMT). No. of bitstreams: 1 DanieleMHM_TESE.pdf: 1582500 bytes, checksum: bba4e28b78ed6df0658bf0c3609ea506 (MD5) Previous issue date: 2011-02-21 / Nickel-bases catalysts have been used in several reform reactions, such as in the partial oxidation of methane to obtain H2 or syngas (H2 + CO). High levels of conversion are usually obtained using this family of catalysts, however, their deactivation resulting from carbon deposition still remains a challenge. Different approaches have been tested aiming at minimizing this difficulty, including the production of perovskites and related structures using modern synthesis methods capable of producing low cost materials with controlled microstructural characteristics at industrial scale. To establish grounds for comparison, in the present study LaNixFe1-xO3 (x=0, 0.3 or 0.7) perovskites were prepared following the Pechini method and by microwave assisted self-combustion. All samples were sub sequently calcined at 900 ?C to obtain the target phase. The resulting ceramic powders were characterized by thermogravimetric analysis, infrared spectroscopy, X ray diffraction, specific area and temperature programmed reduction tests. Calcined samples were also used in the partial oxidation reaction of methane to evaluate the level of conversion, selectivity and carbon deposition. The results showed that the calcined samples were crystalline and the target phase was formed regardless of the synthesis method. According to results obtained by Rietveld refinement, we observed the formation of 70.0% of LaNi0.3Fe0.7O3 and 30.0% of La2O3 for samples LN3F7-900- P, LN3F7-900-M and 41,6% of LaNi0.7Fe0.3O3, 30.7% of La2NiO4 and 27.7% of La2O3 for samples LN7F3-900-P and LN7F3-900-M.Temperature-programmed profiles of the LaNiO3 sample revealed the presence of a peak around 510 ?C, whereas the LaFeO3 sample depicted a peak above 1000?C. The highest l evel of methane conversion was obtained for LaNiO3 synthesized by the Pechini method. Overall, catalysts prepared by the Pechini method depicted better conversion levels compared to those produced by microwave assisted self-combustion / Catalisadores a base de n?quel t?m sido empregados em diversos tipos de rea??es de reforma, inclusive na oxida??o parcial do metano para obten??o de H2 ou g?s de s?ntese (H2 + CO). Normalmente, altos n?veis de convers?o s?o obtidos por estes catalisadores, entretanto, a desativa??o por deposi??o de carbono ainda ? um problema a ser solucionado. Diversas abordagens t?m sido empregadas no intuito de minimizar este problema, dentre as quais tem se destacado nos ?ltimos anos a utiliza??o de ?xidos com estrutura perovisquita e/ou estruturas relacionadas. Paralelamente, o uso de metodologias de s?nteses mais r?pidas, f?ceis, aplic?veis em escala industrial e que permitam o controle das caracter?sticas microestruturais destes catalisadores, pode em conjunto, prover a solu??o para este problema. A n?vel de compara??o perovisquitas do tipo LaNixFe1-xO3 (x=0, x=0,3 e x=0,7) foram preparados por dois m?todos: precursores polim?ricos (pechini) e autocombust?o assistida por microondas. Todas as amostras foram calcinadas a 900 ?C/4h para obten??o das fases desejadas. Os p?s-obtidos foram caracterizados por an?lise termogravim?trica, espectroscopia na regi?o do infravermelho, difra??o de raios-X, medidas de ?rea superficial especifica, redu??o ? temperatura programada. As amostras calcinadas foram testadas na rea??o de oxida??o parcial do metano, sendo avaliados os respectivos n?veis de convers?o, seletividade e a resist?ncia ? deposi??o de carbono. Ap?s calcina??o a fase desejada foi obtida para todas as amostras independente do m?todo de s?ntese, sugerindo claramente a forma??o de p?s cristalinos. De acordo com o resultados obtidos pelo refinamento Rietveld, observou-se a forma??o de 70,0% de LaNi0,3Fe0,7O3 e 30,0 % de La2O3 para as amostras LN3F7-900-P e LN3F7-900-M e 41,6% de LaNi0.7Fe0.3O3; 30,7% de La2NiO4 e 27,7 % de La2O3 para as amostras LN7F3-900-P e LN7F3-900-M. Os perfis de redu??o ? temperatura programada da amostra LaNiO3 apresentou pico de redu??o em torno de 510 ?C, j? a amostra LaFeO 3 apresentou pico de redu??o acima de 1000?C. Dentre os catalisadores estudados o que apresentou maior n?vel de convers?o de metano foi LaNiO3 obtido pelo m?todo pechini, de uma maneira geral os catalisadores obtidos pelo m?todo pechini apresentaram melhores resultados de convers?o que os catalisadores obtidos pela autocombust?o assistida por microondas

Orientador: Carlos Eduardo Vergani / Banca: Ana Cláudia Pavarina / Banca: Elaine Maria Sgavioli Massucato / Banca: Helena de Freitas Oliveira Paranhos / Banca: Karin Hermana Neppelenbroek / Resumo: A estomatite protética é uma infecção fúngica que acomete entre 60% e 72% dos indivíduos portadores de próteses removíveis, sobretudo idosos do gênero feminino. Atualmente, a desinfecção de próteses totais por meio da irradiação por micro-ondas tem sido recomendada para tratamento e prevenção da estomatite protética. Considerando esses aspectos, esse estudo in vivo avaliou a efetividade da frequência da desinfecção de próteses totais por micro-ondas (3 min/650 W) em relação à terapia antifúngica tópica para o tratamento da estomatite protética, além de verificar a prevalência de Candida nos pacientes avaliados. Para isso, foram selecionados 60 indivíduos, portadores de próteses totais superiores e com diagnóstico clínico de estomatite protética. Esses pacientes foram aleatoriamente distribuídos em 3 grupos (n=20), de acordo com o tratamento instituído: Terapia Antifúngica Tópica (Grupo I) - utilização de nistatina (suspensão oral, 100.000 UI/mL), 4 vezes ao dia durante 15 dias; Irradiação por Micro-ondas - imersão das próteses totais em água e irradiação das próteses por micro-ondas durante 3 minutos a 650 W, 1 ou 3 vezes por semana (Grupos II e III, respectivamente) por um período de 15 dias. Para avaliação da efetividade dos tratamentos instituídos, foram realizadas culturas micológicas quantitativas e identificação das espécies de Candida, utilizando-se o meio CHROMagar Candida, análise de microcultivo, teste de triagem em caldo hipertônico e o sistema bioquímico de identificação ID 32C. Coletas de biofilme das superfícies internas das próteses totais superiores e das mucosas palatinas de todos os pacientes, foram realizadas previamente ao tratamento (dia 0) e após 15 dias do seu início. Com o objetivo de avaliar a efetividade dos tratamentos em longo prazo, a quantificação de colônias viáveis de Candiada spp... (Resumo completo, clicar acesso eletrônico abaixo) / Abstract: Denture stomatitis is a fungal infection that affects 60% to 72% of individuals who use removable dentures, primarily elderly women. Currently, the disinfection of complete dentures using microwave irradiation has been recommended to treat and prevent denture stomatitis. Considering these aspects, this in vivo study evaluated the effectiveness of the frequency of complete denture disinfection using microwaves (3 min/650 W) compared to antifungal therapy for the treatment of denture stomatitis. It also verified the prevalence of Candida spp. in the evaluated patients. This study used a sample of 60 healthy individuals who use complete upper dentures and have received a clinical diagnosis of denture stomatitis. Patients were randomly distributed into three groups (n=20), based on the treatment used: Topical Antifungal Therapy (Group I) - use of nystatin (oral suspension, 100.000 UI/mL), four times a day for 15 days; Irradiation with Microwaves - irradiation of the dentures by microwaves for three minutes at 650 W, one time or three times per week (Groups II and III, respectively) for a period of 15 days. In order to evaluate the effectiveness of the treatments used, quantitative mycological cultures were collected and the Candida species were identified using the CHROMagar Candida method, microculture analysis, screening test in hypertonic broth and the ID 32C biochemical identification system. Biofilm samples were collected from the inner surfaces of the complete upper dentures and from the palatal mucosa of all patients before (day 0) and after 15 days of treatment. In order to evaluate the effectiveness of the treatments over the long term, the quantification of the viable Candiada spp. colonies was repeated 30, 60 and 90 days after starting the treatment. For each consultation (days 0, 15, 30, 60 and 90), a clinical evaluation was also performed through intra-oral photography... (Complete abstract click electronic access below) / Doutor