This dissertation contains a comprehensive analysis of both non-coupled and mutually coupled switched reluctance motors with concentrated windings for an electric bicycle traction application. Multiple pole configurations are analyzed and compared for each motor type. Includes magnetic design, thermal analysis, and structural analysis. A prototype is designed, manufactured, and validated. / This thesis discusses the design of both a conventional non-coupled switched reluctance motor (CSRM) and a mutually-coupled SRM (MCSRM) for an exterior rotor e-bike application. Several novel pole configurations were analyzed for each machine type, and the performance of the final CSRM and MCSRM designs were compared for this application. A commercially available e-bike permanent magnet synchronous motor (PMSM) was purchased, reverse engineered, and validated to define the geometry constraints and performance targets for the designs. Since switched reluctance motors do not use rare-earth permanent magnets, they are often seen as a potential low-cost alternative to permanent magnet machines. The goal of this research is to explain the relative advantages of CSRMs and MCSRMs when compared to PMSM machines for a direct-drive e-bike application. The final CSRM and MCSRM designs are analyzed in detail; electromagnetic, controls, thermal, and structural considerations are all studied. A prototype of the final CSRM design was manufactured and validated experimentally, using a dynamometer setup. The finalized CSRM design is shown to be competitive with the PMSM machine when considering torque output, and is superior in terms of peak efficiency, and high speed torque performance. However, the CSRM noise output and torque ripple were not compared to the PMSM, and a less-common asymmetric-bridge converter is required for the CSRM, which may hinder the ability for the machine to be implemented into existing e-bike packages. The high speed torque performance of the MCSRM is shown to be inferior to both the CSRM and PMSM, as is the torque quality and efficiency. The MCSRM is shown to be highly resistant to saturation which gives it the potential for high torque output at low speed (if thermal limits are not breached), though low saturation levels also contribute to low machine power factor. The MCSRM may be better suited to lower speed, high torque applications, for this reason. / Thesis / Doctor of Philosophy (PhD) / This thesis studies the design process and analysis of two different motor types, for an electric bicycle application. They are designed to replace a commercially available permanent magnet synchronous motor (PMSM). This type of motor is typically expensive due to the rare-earth magnet material it requires. The two motors discussed in this thesis are switched reluctance motors (SRMs), which do not require magnet material, and thus have the potential to save cost (in addition to other benefits). One of the SRMs has magnetic fields that are independently controlled (CSRM), and one has fields that are controlled together to produce torque (MCSRM). The magnetics, control, thermal, and structural aspects of the CSRM and MCSRM are studied in detail. Novel geometry considerations (i.e. novel pole configurations) which impact the magnetics of each machine are compared to find the best-performing configuration for each machine type.

The proliferation of modern wireless networks increases demand for high capacity and throughput in order to provide faster, more robust, efficient and broadband services to end users. Mobile WiMAX and LTE are examples of such networks in which for some cases they have exposed limited connectivity due to harsh environment. Relay stations are preferred to overcome problems of weak or no access for such network devices, that are placed in specific positions to maintain high quality of data transfer at low cost and provide the required connectivity anywhere anytime. These stations should be equipped with an antenna system capable of establishing communication between base station (backhaul link) and end users (access link). This thesis focuses on the design and development of a new antenna system that is suitable for a relay-based wireless network. Planar geometries of microstrip patch antennas are utilized. The antenna system comprises two antenna modules: a new design of a single antenna for access link and a new design of an antenna array for backhaul link realization. Both antenna specifications are compatible with the IEEE802.16j protocol standard. Hence, relay station should be capable of pointing its radiation pattern to the base station antenna, thus to achieve the desired radiation pattern of the relay station, a new beam-forming module is proposed, designed and developed to generate the proper radiation pattern. The beam-forming module incorporating digital phase shifters and attenuator chips is fabricated and tested. The optimization process using the Least Mean Square (LMS) algorithm is considered in this study to assign the proper phase and amplitude that is necessary to each radiation element excitation current, to produce the desired steered radiation pattern. A comprehensive study on the coupling effects for several relative positions between two new backhaul and access link antenna elements is performed. Two new antenna configurations for coupling reduction are tested and the simulated and measured results in terms of antenna radiation performances were compared and commented.

Today there is a great need for communication between people and even between things, using systems onboard e.g. aircraft, cars, ships and satellites. As a consequence, these communications needs require antennas mounted on or integrated in the surfaces of different vehicles or platforms, i.e. conformal antennas. In order to ensure proper operation of the communication systems it is important to be able to determine the characteristics of these antennas. This thesis is about the analysis and design of conformal antennas using high frequency asymptotic methods. Commonly used eigenfunction solutions or numerical methods such as FDTD, FEM or MoM are difficult to use for arbitrarily shaped electrically large surfaces. However, the high frequency approximation approach together with an accurate ray tracing procedure offers a convenient solution for these surfaces. The geodesics (ray paths) on the surfaces are key parameters in the analysis and they are discussed in detail. In the first part of the thesis singly and doubly curved perfectly electrical conducting (PEC) surfaces are studied, with respect to the mutual coupling among aperture type elements. A synthesis problem is also considered where the effect of the mutual coupling is taken into account. As expected, the mutual coupling must be included in the synthesis procedure to be able to realize the prescribed pattern, especially in the shaped main lobe. Furthermore, the polarization of the antenna elements is very important when considering antennas on generally shaped surfaces. For such antennas the polarization must most likely be controlled in some way for a proper function. For verification of the results two experimental antennas were built at Ericsson Microwave Systems AB, Mölndal, Sweden. The first antenna is a circular cylinder with an array of rectangular waveguide fed apertures and the second antenna is a doubly curved surface (paraboloid) with circular waveguide fed apertures. It is found that it is possible to obtain very accurate results with the asymptotic method when it is combined with the Method of Moments, i.e. a hybrid method is used. The agreement compared to measurements is good at levels as low as –80 dB in many cases. The second part of the thesis is about the development of a high frequency approximation for surface field calculations on a dielectric covered PEC circular cylinder. When using conformal antennas in practice they have to be covered with a radome for protection and with the method developed here this cover can be included in the analysis. The method is a combination of two different solutions, one valid in the non-paraxial region of the cylinder and the other is valid in the paraxial region. The method is verified against measurements and reference results obtained from a spectral domain moment method code. / QC 20100616

Today, owners of small communicating device are interested in transmitting or receiving various multimedia data. By increasing the number of antennas at the transmitter and/or the receiver side of the wireless link, the diversity/Multiple-Input Multiple-Output (MIMO) techniques can increase wireless channel capacity without the need for additional power or spectrum in rich scattering environments. However, due to the limited space of small mobile devices, the correlation coefficients between MIMO antenna elements are very high and the total efficiencies of MIMO elements degrade severely. Furthermore, the human body causes high losses on electromagnetic wave. During the applications, the presence of users may result in the significant reduction of the antenna total efficiencies and highly affects the correlations of MIMO antenna systems. The aims of this thesis are to investigate and enhance the MIMO/diversity performance of multiple antenna systems in the free space and the presence of users. The background and theory of multiple antenna systems are introduced briefly first. Several figures of merits are provided and discussed to evaluate the multiple antenna systems. The decoupling techniques are investigated in the multiple antenna systems operating at the higher frequencies (above 1.7 GHz) and with high radiation efficiency. The single, dual and wide band isolation enhancements are realized through the half-wavelength decoupling slot, quarter-wavelength decoupling slot with T-shaped impedance transformer, tree-like parasitic element with multiple resonances, as well as the different polarizations and radiation patterns of multiple antennas. In the lower bands (lower than 960 MHz), due to the low radiation efficiency and strong chassis mode, the work mainly focused on how to directly reduce the correlations and enlarge the total efficiency. A new mode of mutual scattering mode is introduced. By increasing the Q factors, the radiation patterns of multiple antennas are separated automatically to reduce the correlations. With the inter-element distance larger than a certain distance, a higher Q factor also improved the total efficiency apart from the low correlation. A wideband LTE MIMO antenna with multiple resonances is proposed in mobile terminals. The high Q factors required for the low correlation and high efficiencies in mutual scattering mode is reduced with another mode of diagonal antenna-chassis mode. Hence, the bandwidth of wideband LTE MIMO antenna with multiple resonances mentioned above can be further enlarged while maintaining the good MIMO/diversity performance. The user effects are studied in different MIMO antenna types, chassis lengths, frequencies, port phases and operating modes. Utilizing these usefully information, an adaptive quad-element MAS has been proposed to reduce the user effects and the some geranial rules not limited to the designed MAS have also been given. / <p>QC 20130121</p> / EU Erasmus Mundus External Cooperation Window TANDEM

Over the last few years, wireless cellular communications has experienced rapid growth in the demand for provision of high data rate wireless multimedia services. This fact motivates the need to find ways to improve the spectrum efficiency of wireless communication systems. Smart or adaptive antennas have emerged as a promising technology to enhance the spectrum efficiency of present and future wireless communications systems by exploiting the spatial domain. The aim of this thesis is to investigate smart antenna applications for Direct Sequence Code Division Multiple Access (DS-CDMA) systems. CDMA is chosen as the platform for this thesis work since it has been adopted as the air-interface technology by the Third Generation (3G) wireless communication systems. The main role of smart antennas is to mitigate Multiple Access Interference (MAI) by beamforming (i.e. spatial filtering) operation. Therefore, irrespective of a particular wireless communication system, it is important to consider whether a chosen array configuration will enable optimal performance. In this thesis an initial assessment is carried out considering linear and circular array of dipoles, that can be part of a base station antenna system. A unified and systematic approach is proposed to analyse and compare the interference rejection capabilities of the two array configurations in terms of the Signal to Interference Ratio (SIR) at the array output. The theoretical framework is then extended to include the effect of mutual coupling, which is modelled using both analytical and simulation methods. Results show that when the performance is averaged over all angles of arrival and mutual coupling is negligible, linear arrays show similar performance as circular arrays. Thus in the remaining part of this thesis, only linear arrays are considered. In order to properly evaluate the performance of smart antenna systems, a realistic channel model is required that takes into account both temporal and spatial propagation characteristics of the wireless channel. In this regard, a novel parameterized physical channel model is proposed in this thesis. The new model incorporates parameters such as user mobility, azimuth angle of arrival, angle spread and Doppler frequency, which have critical influence on the performance of smart antennas. A mathematical formulation of the channel model is presented and the proposed model is implemented in software using Matlab. The statistics of the simulated channels are analysed and compared with theory to confirm that the proposed model can accurately simulate Rayleigh and Rician fading characteristics. To assist system planners in the design and deployment of smart antennas, it is important to develop robust analytical tools to assess the impact of smart antennas on cellular systems. In this thesis an analytical model is presented for evaluating the Bit Error Rate (BER) of a DS-CDMA system employing an array antenna operating in Rayleigh and Rician fading environments. The DS-CDMA system is assumed to employ noncoherent M-ary orthogonal modulation, which is relevant to IS-95 CDMA and cdma2000. Using the analytical model, an expression of the Signal to Interference plus Noise Ratio (SINR) at the output of the smart antenna receiver is derived, which allows the BER to be evaluated using a closed-form expression. The proposed model is shown to provide good agreement with the (computationally intensive) Monte Carlo simulation results and can be used to rapidly calculate the system performance for suburban and urban fading environments. In addition to MAI, the performance of CDMA systems is limited by fast fading. In this context, a hybrid scheme of beamforming and diversity called Hierarchical Beamforming (HBF) is investigated in this thesis to jointly combat MAI and fading. The main idea behind HBF is to divide the antenna elements into widely separated groups to form subbeamforming arrays. The performance of a hierarchical beamforming receiver, applied to an IS-95 CDMA system, is compared with smart antenna (conventional beamforming) receiver and the effect of varying the system and channel parameters is studied. The simulation results show that the performance of hierarchical beamforming is sensitive to the operating conditions, especially the value of the azimuth angle spread. The work presented in this thesis has been published in part in several journals and refereed conference papers, which reflects the originality and significance of the thesis contributions.

Over the last few years, wireless cellular communications has experienced rapid growth in the demand for provision of high data rate wireless multimedia services. This fact motivates the need to find ways to improve the spectrum efficiency of wireless communication systems. Smart or adaptive antennas have emerged as a promising technology to enhance the spectrum efficiency of present and future wireless communications systems by exploiting the spatial domain. The aim of this thesis is to investigate smart antenna applications for Direct Sequence Code Division Multiple Access (DS-CDMA) systems. CDMA is chosen as the platform for this thesis work since it has been adopted as the air-interface technology by the Third Generation (3G) wireless communication systems. The main role of smart antennas is to mitigate Multiple Access Interference (MAI) by beamforming (i.e. spatial filtering) operation. Therefore, irrespective of a particular wireless communication system, it is important to consider whether a chosen array configuration will enable optimal performance. In this thesis an initial assessment is carried out considering linear and circular array of dipoles, that can be part of a base station antenna system. A unified and systematic approach is proposed to analyse and compare the interference rejection capabilities of the two array configurations in terms of the Signal to Interference Ratio (SIR) at the array output. The theoretical framework is then extended to include the effect of mutual coupling, which is modelled using both analytical and simulation methods. Results show that when the performance is averaged over all angles of arrival and mutual coupling is negligible, linear arrays show similar performance as circular arrays. Thus in the remaining part of this thesis, only linear arrays are considered. In order to properly evaluate the performance of smart antenna systems, a realistic channel model is required that takes into account both temporal and spatial propagation characteristics of the wireless channel. In this regard, a novel parameterized physical channel model is proposed in this thesis. The new model incorporates parameters such as user mobility, azimuth angle of arrival, angle spread and Doppler frequency, which have critical influence on the performance of smart antennas. A mathematical formulation of the channel model is presented and the proposed model is implemented in software using Matlab. The statistics of the simulated channels are analysed and compared with theory to confirm that the proposed model can accurately simulate Rayleigh and Rician fading characteristics. To assist system planners in the design and deployment of smart antennas, it is important to develop robust analytical tools to assess the impact of smart antennas on cellular systems. In this thesis an analytical model is presented for evaluating the Bit Error Rate (BER) of a DS-CDMA system employing an array antenna operating in Rayleigh and Rician fading environments. The DS-CDMA system is assumed to employ noncoherent M-ary orthogonal modulation, which is relevant to IS-95 CDMA and cdma2000. Using the analytical model, an expression of the Signal to Interference plus Noise Ratio (SINR) at the output of the smart antenna receiver is derived, which allows the BER to be evaluated using a closed-form expression. The proposed model is shown to provide good agreement with the (computationally intensive) Monte Carlo simulation results and can be used to rapidly calculate the system performance for suburban and urban fading environments. In addition to MAI, the performance of CDMA systems is limited by fast fading. In this context, a hybrid scheme of beamforming and diversity called Hierarchical Beamforming (HBF) is investigated in this thesis to jointly combat MAI and fading. The main idea behind HBF is to divide the antenna elements into widely separated groups to form subbeamforming arrays. The performance of a hierarchical beamforming receiver, applied to an IS-95 CDMA system, is compared with smart antenna (conventional beamforming) receiver and the effect of varying the system and channel parameters is studied. The simulation results show that the performance of hierarchical beamforming is sensitive to the operating conditions, especially the value of the azimuth angle spread. The work presented in this thesis has been published in part in several journals and refereed conference papers, which reflects the originality and significance of the thesis contributions.

Abstract This dissertation presents wideband and multi-element antennas for mobile applications. It is divided into the following main parts: modal theory, wideband antennas, multi-element antennas, and wideband multi-element antennas. The radiating fields are first studied in terms of spherical scalar and vector modes, and it is shown how these modes correlate with the characteristic current modes on a planar mobile ground plane. The theory part shows how it is possible to excite the same modes on a conventional sphere and a rectangular planar mobile ground plane. The theory refers to the novel wideband antenna structures presented in this dissertation, in terms of current and radiating modes. After studying the modes, the dissertation shows how to excite a radiating antenna mode within a wide frequency bandwidth. To gain this, two main approaches are taken. First, a quasi-complementary antenna (QCA) structure with an electric conductor and magnetic slot is presented, and its characteristics are studied. A QCA UWB antenna, and a QCA element excited with a monopole or a dipole, is presented. The QCA structure compensates for the imaginary part of the input impedance on wide frequency bandwidth, when, at the same time, the fundamental mode is excited to ensure good radiating properties. The second approach uses a symmetrical feeding with two antenna elements to gain a wide frequency bandwidth, the relative -6 dB impedance bandwidth between 37.5–80%. When a field is symmetrically coupled to the conducting ground plane, the excitation avoids the awakening of higher order modes which might disturb the performance of the antenna. It is also shown, by using multiple feeding elements, that the excitation of orthogonal higher order modes on a small radiating ground plane is possible. As the modes are orthogonal to each other, they present a very low correlation. By using this kind of approach, radiation pattern diversity can be obtained in mobile applications within a small volume. On the other hand, when combining two QCA elements to a one multi-element antenna structure, a wideband diversity antenna with an 87.5% relative -6 dB impedance bandwidth, and a wideband MIMO antenna with a 95.0% relative -6 dB impedance bandwidth, are presented with excellent radiation and correlation properties. Also mutual coupling is need to be counted when multi-element antennas are designed. When designing an efficient radiator, it is important to consider an antenna feeding in terms of wideband impedance matching and wideband baluns, not to spoil the antenna performance. The efficient antenna structures and feeding mechanisms are obtained by using commercial 3D electromagnetic simulators to find the desired wideband antenna characteristics. Prototype antennas are measured in most of the presented structures to show their functionality in real. In general, the dissertation presents wideband antenna structures with radiating antenna modes excited on a planar conducting ground plane. The idea is to find structures and feeding mechanisms to excite the fundamental mode, or a certain radiating antenna mode, at a wide frequency bandwidth, by avoiding the excitation of higher order modes which might disturb the antenna performance. It is also shown that, by using multiple feeding elements, it is possible to excite higher order modes on a small antenna. / Tiivistelmä Väitöskirjassa esitetään uusia laajakaistaisia ja monielementtiantenneja matkaviestimiin. Väitöskirja koostuu neljästä pääalueesta: pintavirtojen muototeoria, laajakaistaiset antennit, monielementtiantennit sekä laajakaistaiset monielementtiantennit. Teoriaosassa säteilykenttiä on aluksi tutkittu pallon pinnalla sekä skalaaripotentiaaleina että pintavirtavektoreina, jonka jälkeen niitä on verrattu mobiilin laitteen maatason ominaispintavirtojen synnyttämiin säteilykenttiin. Teoriaosassa osoitetaan, että pallon pinnalla sekä tasomaisella suorakaiteen muotoisella pinnalla on mahdollista herättää samat säteilykentät. Myöhemmin väitöskirjassa esitettävien uudenlaisten antennirakenteiden ominaisuuksia verrataan teoriaosassa esitettyihin pintavirtoihin ja säteilykenttiin. Teoriaosuuden jälkeen osoitetaan miten säteilevä sähkömagneettinen kenttä saadaan herätettyä laajalla taajuusalueella. Tähän on otettu kaksi eri lähestymistapaa, joista ensimmäisessä esitellään ja tutkitaan kvasikomplementaarista antennirakennetta (QCA). Kvasikomplementaarisessa antennirakenteessa sisääntuloimpedanssin imaginaariosa kompensoidaan yhdistämällä sähköinen johde ja magneettinen rako samaan antenniin. Samanaikaisesti perusmuoto herätetään laajalla taajuusalueella, jolla varmistetaan antennin hyvät säteilyominaisuudet koko toimintataajuusalueella. Toisessa lähestymistavassa käytetään kahta symmetrisesti asetettua antennielementtiä, joita syötetään symmetrisesti samalla amplitudilla ja vaiheella. Kun sähkömagneettinen kenttä herätetään symmetrisesti, korkeamman kertaluvun muotojen herättäminen voidaan välttää laajalla taajuusalueella. Symmetrisesti syötetyillä antennirakenteilla saavutettu -6&#160;dB suhteellinen impedanssikaistanleveys on 37.5–80&#160;%. Useita syöttöelementtejä käytettäessä voidaan mobiilin laitteen maatasossa herättää yhdellä pistetaajuudella monta toisistaan riippumatonta säteilykenttää. Koska herätetyt kentät ovat toisistaan riippumattomia, on niiden välinen korrelaatio myös pieni. Kyseisellä rakenteella on mahdollista toteuttaa säteilykuviodiversiteetti erittäin pienessä tilassa, kuten matkapuhelimessa. Toisaalta, kun yhdistetään kaksi QCA-elementtiä yhdeksi monielementtiratkaisuksi, voidaan toteuttaa laajakaistainen diversiteettiantenni, jonka suhteellinen -6&#160;dB impedanssikaistanleveys on 87.5&#160;%. Vastaavasti kahdella laajakaistaisella QCA-elementillä toteutetulla MIMO-ratkaisulla päästään 95&#160;% suhteelliseen -6&#160;dB impedanssikaistanleveyteen. Molemmilla ratkaisuilla on erittäin hyvät säteilyominaisuudet sekä alhainen korrelaatio ja pieni keskinäiskytkentä antennielementtien välillä. Suunniteltaessa toimivaa laajakaistaista antennirakennetta, on tärkeää ottaa huomioon antennisyötön impedanssisovitus, jotta antennin suorituskyky ei heikkenisi. Lisäksi balansoidussa rakenteissa tulee olla laajakaistainen baluni, jolla vältetään säteilykuvion vääristyminen. Väitöskirjan syöttöratkaisuissa on käytetty kaupallisia sähkömagneettisia simulaattoreita, joilla antennirakenne voidaan mallintaa kolmiulotteisesti, ja joilla laajakaistainen syöttö saadaan optimoitua haluttuun antenniin. Suurin osa esitellyistä antennirakenteista on simulointien lisäksi myös mitattu, jolloin niiden toimivuus käytännössä pystytään todentamaan rakentamalla prototyyppiantenni. Yleisesti väitöskirjassa esitellään tasomaisia antenniratkaisuja johtavassa maatasossa, joissa säteilevät pintavirrat herätetään mahdollisimman laajalla taajuusalueella. Ideana on löytää laajakaistaisia antenni- ja syöttörakenteita, joilla saadaan herätettyä perusmuoto tai jokin muu haluttu muoto. Ajatuksena on välttää korkeamman kertaluvun muotojen herättäminen, jotka voivat pilata antennin suorituskyvyn. Väitöskirjassa osoitetaan myös, että pienikokoisella antennilla on mahdollista herättää korkeamman kertaluvun muotoja pistetaajuudella käyttämällä useita heräte-elementtejä.

Les propriétés thermiques exceptionnelles de l’hélium superfluide, ou He-II, sont mises à profit pour la réfrigération cryogénique d'installations de forte puissance, bien que les mécanismes physiques sous-jacents restent mal compris. L’He-II peut être décrit à l’échelle macroscopique comme la superposition de deux fluides en interaction : un fluide normal se comportant comme un liquide ordinaire, et un superfluide sans viscosité. En présence d’une source de chaleur, un contre-courant s’établit naturellement entre ces deux composantes. L’évacuation de la chaleur par ce contre-courant est limitée par l’apparition d’instabilités dans des conditions mal comprises ; la grande dispersion des données expérimentales ne permettant pas de discriminer les différents modèles théoriques. Cette thèse examine à l’aide de simulations numériques le rôle des conditions aux bords et du couplage mutuel entre les deux composantes de l’He-II dans le déclenchement des instabilités de contre-courant.Une approche originale de type Boltzmann sur réseau a été développée pour modéliser à l’échelle mésoscopique l'interaction entre les deux composantes de l’He-II. Un code reproduisant les écoulements de contre-courant en conduite 2d et 3d a été développé et validé. Les résultats obtenus indiquent des effets d’entrée de conduite amplifiés pour la composante superfluide, qui engendrent des pertes de charge anormalement élevées. Le mécanisme responsable de ces effets d’entrée a été étudié et il est montré qu'il peut fausser la détection du seuil de transition dans des conduites trop courtes ; ceci peut expliquer en partie la dispersion des données expérimentales.Pour illustrer la puissance de l'approche dans une géométrie complexe, le sillage d'un obstacle dans un écoulement de contre-courant a été simulé. La présence de zones de recirculation des deux côtés de l’obstacle, déjà observée expérimentalement, est retrouvée et expliquée par un mécanisme original de parois virtuelles. / The exceptional thermal properties of superfluid helium, or He-II, are exploited to the cryogenic refrigeration of high power installations, although the underlying physical mechanisms remain poorly understood. The He-II can be described macroscopically as the superposition of two fluids in interaction: a normal fluid behaves as an ordinary liquid, and a superfluid without viscosity. In the presence of a heat source, a counterflow established between these two components. The heat dissipation by this counterflow is limited by the occurrence of instabilities in misunderstood condition; the wide dispersion of experimental data does not allow to discriminate between the different theoretical models. This thesis examines using numerical simulations the role of boundary conditions and the mutual coupling between the two components of the He-II in triggering instabilities in counterflow.An innovative lattice Boltzmann type approach was developed to model the mesoscopic scale interaction between the two components of the He-II. A code reproducing counterflow in 2D and 3D conducts has been developed and validated. The results obtained indicate amplified entrance effects for superfluid component, which generate abnormally high pressure drops. The head of these entrance effects mechanism has been studied and it is shown that it can distort the detection of the transition threshold in too short pipes; This may partly explain the dispersion of experimental data.To illustrate the power of the approach in a complex geometry, the wake of an obstacle in a counterflow was simulated. The presence of recirculation areas on both sides of the obstacle, already observed experimentally, is found and explained by a new mechanism using "virtual walls".

Cette thèse se place dans le contexte général de la modélisation de réseaux d’antennes de grande taille, avec pour objectif d’atteindre un niveau de précision suffisamment élevé pour permettre une optimisation complète des performances et en particulier une amélioration de l’efficacité énergétique. Partant du constat que l’optimisation électromagnétique de grands réseaux représente un verrou si les couplages doivent être modélisés efficacement, cette thèse propose la mise en œuvre d’une méthode permettant la modélisation fine de grands réseaux d'antennes tout en réduisant les temps de calcul et en conservant un haut degré de précision. L'objectif est de montrer qu'une approche dérivée des formalismes périodiques infinis connus de la littérature permet d'obtenir une matrice [S] complète d'un réseau depuis l'étude d'une cellule unitaire. Après avoir présenté un état de l'art sur les réseaux d'antennes et leurs méthodes d'analyse, l'approche de modélisation proposée est détaillée. Des véhicules de test numériques et expérimentaux, permettant de valider cette méthode de modélisation, sont ensuite réalisés. L'approche est enfin utilisée avec succès pour deux types d'application. / This thesis is organized in the general context of modeling a large antenna arrays with the aim of achieving a high level of precision. This modeling allows a complete optimization of the performances and an enhancement of the energy efficiency. Given that the electromagnetic optimization of large arrays still represents a challenge if the mutual coupling is not efficiently modeled. This work offers the implementation of a method allowing the precise modeling of large antenna arrays while reducing the computation time and maintaining a high degree of precision. The aim is to demonstrate that the derived approach from the infinite periodic formalisms makes it possible to obtain a full [S] matrix of an array based on the study of a unit cell. After presenting a state of the art of antenna arrays and their methods of analysis, the proposed modeling approach is explained. Numerical and Experimental demonstrators are then made for the validation. Finally, this method is successfully used for two types of applications.

Les travaux de cette thèse s’intéressent à un nouveau concept d’antenne reconfigurable offrant un bon compromis entre performances, complexité et coût. Ce concept, qualifié d’hybride, vise à combiner les avantages des réseaux d’antennes lacunaires et des antennes à éléments parasites. Cette hybridation est une alternative à la complexité des réseaux d’antennes conventionnels pour répondre aux exigences d’une architecture modulaire, générique et reconfigurable. L’intérêt majeur de ce concept est de proposer une architecture d’antenne permettant de réduire la complexité du circuit de formation des faisceaux (par la réduction du nombre d’éléments rayonnants à alimenter) tout en adressant les problématiques d’adaptation (TOS actif) des éléments excités. Ceci est permis grâce à la présence d’éléments parasites qui permettent de gérer la diffusion des couplages sur l’antenne. Cette thèse décrit le principe du concept hybride et propose une évaluation de ses potentialités. Par la suite, une définition des éléments à mettre en œuvre pour réaliser une preuve de concept est effectuée, en mettant l’accent sur l’importance de la caractérisation expérimentale. Les performances d’un prototype d’antenne hybride reconfigurable sont ensuite présentées afin de valider les développements et conclure sur cette solution innovante. / The work of this thesis aims to investigate a new concept of reconfigurable antenna allowing a good trade-off between performances, complexity and cost. This concept is called ‘hybrid’ because it is based on the capabilities of thinned arrays and parasitic element antennas. It is an alternative to classical antenna arrays and their complexity. The proposed concept has a modular architecture, and a good versatility for reconfigurable beams. The main advantage of this hybrid antenna is the simplicity of its beam formation network (BFN) which requires only a few number of excited elements. The antenna uses parasitic elements to manage the effects of couplings between the electromagnetic access. The problematic of active VSWR is also solved at the antenna level, avoiding the use of additional components in the BFN. This work details the principle of the reconfigurable hybrid antenna concept. The potentialities are evaluated. The elements required to realize a proof of concept are then defined, using a dedicated experimental setup. A prototype is manufactured and the performances have been checked to validate this innovative concept.