The design and implementation of mm-wave switches, variable attenuators, and a passive imaging system in 65-nm CMOS are presented. The design and analysis of shunt switches is presented with a demonstration circuit showing record performance for a single-pole single-throw switch with 1.6dB loss and 30dB isolation at 94GHz. Single-pole double-throw (SPDT) switches are shown, with 4dB insertion loss in the W-band (75-110GHz), and the only reported SPDT switch operating in the D-band (110-170GHz). A novel technique for implementing digitally controlled variable attenuation is presented, resulting in variable attenuation between 4 and 30dB in the W-band. Finally, a W-band radiometer is described integrating a record-high gain CMOS LNA, SPDT switch, and peak detector. This is the highest-frequency imaging system in CMOS with this level of integration, offering a responsivity over 90kV/W, and a noise-equivalent power less than 0.2pW/√Hz.

Objective: To determine if significant differences exist in timings and rates of Peak Mandibular Growth (PMG) and mandibular projections of subjects with vertical, average and horizontal facial growth patterns. Methods: Sixty-three Caucasian orthognathic subjects with cephalograms (9 to 18 years) available from the Burlington Growth Centre were categorized into average, vertical and horizontal growth pattern groups based on their change in Y axis from age 10 to 16 years. PMG timing and rates were determined and mandibular projections measured. Comparisons were made by ANOVA. Results: Inter-group differences of PMG timing or rate were not statistically significant. Although not statistically significant, PMG of vertically growing females was 14 month earlier than all other subgroups. Horizontal mandibular projection differences approached significance in older children. Conclusions: No statistically significant differences were found in the timing or rate of PMG in different facial growth patterns. Differences in horizontal mandibular projections approached significance with growth.

A detailed study was made of the composition and distribution of modern and fossil animal and plant traces around saline, alkaline lakes in tectonically active, closed lake-basins. Modern and Pleistocene traces that were examined in lake basins of the Kenya Rift Valley (Lakes Bogoria, Magadi, and Nasikie Engida) were compared directly with fossil traces from the Eocene Lake Gosiute in the Green River Formation of Wyoming, U.S.A., which had a similar hydrochemistry. Analysis of lithofacies and the stratigraphic packaging of the sediments hosting biogenic structures was undertaken so that their vertical and lateral distribution could be used to interpret lake histories and to help to develop depositional models of enigmatic sedimentary successions. A focus was given to the application of the results for paleoecology and stratigraphy, and a model for predicting the position of different trace associations in vertical successions and in different parts of saline, alkaline lake basins has been developed. Evidence from the Kenyan lakes and Eocene Lake Gosiute shows that (1) sedimentary environments are diverse in underfilled basins, and frequent lake-level fluctuations strongly impact the distribution of sedimentary environments suitable for the production and preservation of biogenic structures; (2) the distribution of biogenic structures in underfilled basins is related to the geomorphological and structural setting, tectonic activity, catchment lithology, the basin margin or basin centre location, climate, and salinity and alkalinity, together with other finer-scale environmental and biological controls; (3) because saline environments are restrictive, sites of relatively dilute inflow (springs, rivers and deltas, ephemeral streams) provide oasis-like habitats for animals and plants, and contribute to the increased diversity and laterally variable distribution of saline-lake trace assemblages; and (4) the vertical distribution of trace fossils in a stratigraphic succession reflects changing environments through time; important stratigraphic surfaces, usually formed during periods of lake-level fall, can be recognized from the overprinting patterns of traces produced under different conditions.

<p>In this dissertation work, the aim was to garner better mechanistic understanding of how shock wave lithotripsy (SWL) breaks stones in order to guide design improvements to a modern electromagnetic (EM) shock wave lithotripter. To accomplish this goal, experimental studies were carefully designed to isolate mechanisms of fragmentation, and models for wave propagation, fragmentation, and stone motion were developed. In the initial study, a representative EM lithotripter was characterized and tested for in vitro stone comminution efficiency at a variety of field positions and doses using phantom kidney stones of variable hardness, and in different fluid mediums to isolate the contribution of cavitation. Through parametric analysis of the acoustic field measurements alongside comminution results, a logarithmic correlation was determined between average peak pressure incident on the stone surface and comminution efficiency. It was also noted that for a given stone type, the correlations converged to an average peak pressure threshold for fragmentation, independent of fluid medium in use. The correlation of average peak pressure to efficacy supports the rationale for the acoustic lens modifications, which were pursued to simultaneously enhance beam width and optimize the pulse profile of the lithotripter shock wave (LSW) via in situ pulse superposition for improved stone fragmentation by stress waves and cavitation, respectively. In parallel, a numerical model for wave propagation was used to investigate the variations of critical parameters with changes in lens geometry. A consensus was reached on a new lens design based on high-speed imaging and stone comminution experiments against the original lens at a fixed acoustic energy setting. The results have demonstrated that the new lens has improved efficacy away from the focus, where stones may move due to respiration, fragmentation, acoustic radiation forces, or voluntary patient movements. Using traditional theory of brittle fragmentation and newfound understanding of average peak pressure correlation to stone comminution, the entire set of stone comminution data for lens comparison was modeled using a Weibull-style distribution function. This model linked both the average peak pressure and shock wave dose to efficacy, including their respective threshold parameters, and demonstrated correlation of coefficients to cavitation activity. Subsequently, this model was used in prediction of stone comminution efficiency from mimicked respiratory motions in vitro, which compared favorably to actual simulated motion studies using both the new and original lenses. Under a variety of mimicked respiratory motions, the new lens produced statistically higher stone comminution efficiency than the original lens. These results were confirmed in vivo in a swine model, where the new lens produced statistically higher stone comminution after 1,000 and 2,000 shocks. Finally, a mechanistic investigation into the effects of cavitation with the original lens was conducted using an integrated, self-focusing annular ring transducer specially designed for tandem pulse lithotripsy. It was found that cavitation and stone comminution efficiency are progressively enhanced by tandem pulsing as source energies of both the primary LSW and trailing pressure pulse increase, which suggests cavitation and stress waves act synergistically enhance the efficacy in kidney stone fragmentation.</p> / Dissertation

Vi står inför en förändring, att minska vårt beroende av fossil energi till förmån för en ökad användning av förnybar energi. Incitament i form av ökade punktskatter på fossilt bränsle påskyndar omställningen för företag till förnybar energi och- eller energieffektivisering av sin produktion. Konsekvensen blir en successivt fördyrad kostnad för produktion av fjärrvärme med eldningsolja till tillverkningsindustrin. Punktskatt på eldningsolja stiger med 41 procent, från 2010 till 2015 för företagen. Att konvertera befintliga oljepannor med träpulverbrännare är en lösning för att hålla produktionskostnaden nere och behålla sin konkurrenskraft. I detta examensarbete utreds möjligheten att konvertera oljepannor i storleksklassen 5-10 MW. Studien tar ett helhetsgrepp om RMT´s fjärrvärmeproduktion för att söka svaret på, om det är möjligt att göra en konvertering ur ett tekniskt, hållbarhets och ekonomiskt perspektiv. Det kända behovet av spetslast från oljepannorna vid -3°C visade sig inte stämma utan brytpunkten hamnade vid -6°C. Resultatet pekar på att en 10 MW oljepanna kan konverteras till 5 MW träpulver men ändå behålla sin ursprungliga effekt genom en kombibrännare. Tidigare problem som fanns med träpulveranläggningar är åtgärdade och referensanläggningar i den aktuella storleksklassen finns i drift. Ett förfrågningsunderlag skickades ut för att få in budgetpris på konvertering av 5 och 10 MW oljepannor för utvärdering. Trots att alla leverantörer gavs samma förutsättningar så varierade budgetpriserna väldigt mycket. En stor överraskning var den korta payoff tid på konverteringar med liten värmeeffekt. Att en konvertering av en 10 MW OP har en återbetalningstid på 20 månader var rätt osannolikt innan studien utfördes. Denna studie kan även ses som en inspirationskälla till andra företag som har mindre spetslastpannor och vill fasa ut sitt fossila beroende med förnybar energi, samtidigt behålla sin konkurrenskraft. I fjärrvärmebranschen är dessa 5 och 10 MW oljepannor vanliga som spetslastpannor. Det finns ca 1000 oljepannor i storleken 5-10 MW i Sverige så det bör finnas en stor potential i att konvertera oljepannor till träpulver. / We are facing a change, to reduce our dependency on fossil fuels in favor of increased use of renewable energy. Incentives in the form of increased excise taxes on fossil fuels for companies accelerate the conversion to renewable energy or energy efficiency of its production. The consequence is a progressively more expensive cost for district heating with fuel oil to manufacturing industry. Excise tax on fuel oil rises by 41 percent, from 2010 to 2015 for those companies. To convert existing oil boilers with woodpowderburner is a solution to keep production costs down and remain competitive. In this thesis studied the possibility of converting oil boilers in the size range of 5 to 10 MW. The study takes a holistic approach to RMT's district heating to search the answer, if it is possible to do a conversion from a technical, sustainability and economic perspective. The felt need for peak load from oil boilers at -3° C appeared not to sue; it ended up at -6° C. The results indicate that a 10 MW oil boiler can be converted to 5 MW wood powder and while retaining its original power through a combination burner. Previously problems with woodpowderplant are taken care of and reference facilities in the current magnitude are in operation. An inquiry was sent out to get budget prices at a conversion of 5 and 10 MW oil boilers for evaluation. Even though all the suppliers was given the same opportunities so varied budget prices very much. A big surprise was the short payoff time on conversions of small oil boilers. The conversion of a 10 MW OP has a payback period of 20 months and that was rather unlikely before the study was performed. This study can also be seen as a source of inspiration to other companies that have small peak load boilers and want to phase out their fossil fuel dependence with renewable energy, and retain their competitiveness. In the district heating sector, these 5 and 10 MW oil boilers are ordinary peak load boilers. There are about 1000 oil boilers in the size from 5 to 10 MW in Sweden so it should be a large potential in converting oil boilers to wood powder

High-peak power laser systems are defined along with a brief introduction of the technology used in their development and application to the project. A review of concepts surrounding optical pulses, focusing on the particular phenomena involved with the ultrafast, follows. Numerical models involving optical pulses are introduced and verified. An extensive description of the laser system is presented, including models used in its design. Data verifying the correct operation of the laser system is presented and interpreted. A dispersion compensation system, including a function model, is introduced, and its application to the laser system is analyzed. An introduction to pulse characterization techniques is presented followed by the design and verification of two different characterization devices. Experiments utlizing the dispersion compensation system and pulse characterization devices are presented and the results are interpreted. Conclusions are made regarding the performance of the laser system models and pulse characterization devices, along with suggested improvements for each. The results of the experiments are discussed including suggestions for future work.

Ion current sensing, where information about the combustion process in an SI-engine is gained by applying a voltage over the spark gap, is currently used to detect and avoid knock and misfire. Several researchers have pointed out that information on peak pressure location and air/fuel ratio can be gained from the ion current and have suggested several ways to estimate these parameters. Here a simplified Bayesian approach was taken to construct a lowpass-like filter or estimator that makes use of prior information to improve estimates in crucial areas. The algorithm is computationally light and could, if successful, improve estimates enough for production use. The filter was implemented in several variants and evaluated in a number of simulated cases. It was found that the proposed filter requires a number of trade-offs between variance, bias, tracking speed and accuracy that are difficult to balance. For satisfactory estimates and trade-off balance the prior information must be more accurate than was available. It was also found that similar a task, constructing a general Bayesian estimator, has already been tackled in the area of particle filtering and that there are promising and unexplored possibilities there. However, particle filters require computational power that will not be available to production engines for some years. / Vid jonströmsmätning utvinns information om förbränningsprocessen i en bensinmotor genom att en spänning läggs över gnistgapet och den resulterande strömmen mäts. Jonströmsmätning används idag för knack- och feltändningsdetektion. Flera forskare har påpekat att det finns än mer information i jonströmmen, bl.a. om bränsleblandningen och cylindertrycket och har även föreslagit metoder för att utvinna och använda den informationen för skattning av dessa parametrar. Här presenteras en förenklad Bayesisk metod i form av en lågpassfilter-liknande skattare som använder förkunskap till att förbättra estimat på relevanta områden. Algoritmen är beräkningsmässigt lätt och kan, om den är framgångsrik, leverera skattningar av förbränningsparametrar som är tillräckligt bra för att användas för sluten styrning av en bensinmotor. Skattaren, eller filtret, implementerades i flera varianter och utvärderades i ett antal simulerade fall. Resultaten visade på att flera svåra avvägningar måste göras mellan förbättring i varians, avvikelse och följning eftersom förbättring i den ena ledde till försämring i de andra. För att göra dessa avvägningar och få goda skattningar krävs bättre förhandskunskap och mätdata än vad som var tillgängligt. Bayesisk skattning är ett stort befintligt område inom statistik och signalbehandling och den mest generella skattaren är partikelfiltret som har många intressanta tillämpningar och möjligheter. De har hittills inte använts inom skattning av förbränningsparametrar och har således go potential för framtida utveckling. De är dock beräkningsmässigt tunga och kräver beräkningsresurser utöver vad som är tillgängliga i ett motorstyrsystem idag.

High-peak power laser systems are defined along with a brief introduction of the technology used in their development and application to the project. A review of concepts surrounding optical pulses, focusing on the particular phenomena involved with the ultrafast, follows. Numerical models involving optical pulses are introduced and verified. An extensive description of the laser system is presented, including models used in its design. Data verifying the correct operation of the laser system is presented and interpreted. A dispersion compensation system, including a function model, is introduced, and its application to the laser system is analyzed. An introduction to pulse characterization techniques is presented followed by the design and verification of two different characterization devices. Experiments utlizing the dispersion compensation system and pulse characterization devices are presented and the results are interpreted. Conclusions are made regarding the performance of the laser system models and pulse characterization devices, along with suggested improvements for each. The results of the experiments are discussed including suggestions for future work.

The increasing penetration of distributed generation (DG) in power distribution systems presents technical and economic benefits as well as integration challenges to utility engineers. Governments are beginning to acknowledge DG as an economically viable alternative to deferring investment at generation, transmission and distribution levels, meeting demand growth and improving distribution network performance and security. DG technology is rapidly maturing in Ontario due to government economic incentives promoting connection, specifically, the Ontario’s Feed-In-Tariff (FIT) Program. Optimal sizing and siting of DG is well researched, traditionally studying the technical impact on distribution system such as real power loss reduction and voltage profile improvement. Equally common objectives studied are the economics of DG installation which are useful for the developer when deciding when and where to install. Although DG represents a “non-wires” solution to network asset reinforcement, the direct economic benefit to the host utility from promoting DG uptake is not fully understood by utility planners and asset managers. Some DG based asset reinforcement deferral work has been performed in the UK and Italy but is mainly at the transmission level and is not part of an overall strategy that could be applied by a utility. This research presents a comprehensive three stage technique: optimal siting, optimal sizing and financial evaluation of cost savings over a defined planning period to quantify the economic benefit to a Local Distribution Company (LDC) of solar photovoltaic (PV) DG connections on an actual distribution feeder. Optimal sites for PV DG are determined by applying the power loss sensitivity factor method to the test feeder. The objective functions used to determine cost savings consist of loss minimization, asset investment deferral, and peak demand reduction to identify an optimal DG penetration limit. Furthermore, a utility planner can identify an optimal DG penetration limit, encourage uptake at preferred locations that would benefit the LDC, and use the positive impact of DG at existing locations as part of an asset management strategy to prioritize and schedule future asset reinforcement upgrades.

A detailed study was made of the composition and distribution of modern and fossil animal and plant traces around saline, alkaline lakes in tectonically active, closed lake-basins. Modern and Pleistocene traces that were examined in lake basins of the Kenya Rift Valley (Lakes Bogoria, Magadi, and Nasikie Engida) were compared directly with fossil traces from the Eocene Lake Gosiute in the Green River Formation of Wyoming, U.S.A., which had a similar hydrochemistry. Analysis of lithofacies and the stratigraphic packaging of the sediments hosting biogenic structures was undertaken so that their vertical and lateral distribution could be used to interpret lake histories and to help to develop depositional models of enigmatic sedimentary successions. A focus was given to the application of the results for paleoecology and stratigraphy, and a model for predicting the position of different trace associations in vertical successions and in different parts of saline, alkaline lake basins has been developed. Evidence from the Kenyan lakes and Eocene Lake Gosiute shows that (1) sedimentary environments are diverse in underfilled basins, and frequent lake-level fluctuations strongly impact the distribution of sedimentary environments suitable for the production and preservation of biogenic structures; (2) the distribution of biogenic structures in underfilled basins is related to the geomorphological and structural setting, tectonic activity, catchment lithology, the basin margin or basin centre location, climate, and salinity and alkalinity, together with other finer-scale environmental and biological controls; (3) because saline environments are restrictive, sites of relatively dilute inflow (springs, rivers and deltas, ephemeral streams) provide oasis-like habitats for animals and plants, and contribute to the increased diversity and laterally variable distribution of saline-lake trace assemblages; and (4) the vertical distribution of trace fossils in a stratigraphic succession reflects changing environments through time; important stratigraphic surfaces, usually formed during periods of lake-level fall, can be recognized from the overprinting patterns of traces produced under different conditions.