The development and characterization of experimental setups for angle-resolved photoelectron spectroscopy (ARPES) and spin- and angle-resolved photoelectron spectroscopy (SARPES) is described. Subsequently, the two techniques are applied to studies of the electronic band structure in topologically non-trivial materials. The laser-based ARPES setup works at a photon energy of 10.5 eV and a typical repetition rate in the range 200 kHz to 800 kHz. By using a time-of-flight electron energy analyzer electrons emitted from the sample within a solid angle of up to ±15 degrees can be collected and analyzed simultaneously. The SARPES setup is equipped with a traditional hemispherical electron energy analyzer in combination with a mini-Mott electron polarimeter. The system enables software-controlled switching between angle-resolved spin-integrated and spin-resolved measurements, thus providing the possibility to orient the sample by mapping out the electronic band structure using ARPES before performing spin-resolved measurements at selected points in the Brillouin zone. Thin films of the topological insulators (TIs) Bi2Se3, Bi2Te3 and Sb2Te3 are grown using e-beam evaporation and their surface states are observed by means of ARPES. By using a combination of low photon energies and cryogenic sample temperatures the topological states originating from both the vacuum interface (surface) and the substrate interface are observed in Bi2Se3 films and Bi2Se3/Bi2Te3 heterostructures, with total thicknesses in the ultra-thin limit (six to eight quintuple layers), grown on Bi-terminated Si(111) substrates. Band alignment between Si and Bi2Se3 at the interface creates a band bending through the films. The band bending is found to be independent of the Fermi level (EF) position in the bulk of the substrate, suggesting that the surface pinning of EF in the Si(111) substrate remains unaltered after deposition of the TI films. Therefore, the type and level of doping of the substrate does not show any large influence on the size of the band bending. Further, we provide experimental evidence for the realization of a topological crystalline insulator (TCI) phase in the narrow-band semiconductor Pb1−xSnxSe. The TCI phase exists for temperatures below the transition temperature Tc and is characterized by an inverted bulk band gap accompanied by the existence of non-gapped surface states crossing the band gap. Above Tc the material is in a topologically trivial phase where the surface states are gapped. Thus, when lowering the sample temperature across Tc a topological phase transition from a trivial insulator to a TCI is observed. SARPES studies indicate a helical spin structure of the surface states both in the topologically trivial and the TCI phase. / <p>QC 20130507</p>

There are today clear indications that the Li-ion battery of the type currently used worldwide in mobile-phones and lap-tops is also destined to soon become the battery of choice in more energy-demanding concepts such as electric and electric hybrid vehicles (EVs and EHVs). Since the currently used cathode materials (typically of the Li(Ni,Co)O2-type) are too expensive in large-scale applications, these new batteries will have to exploit some much cheaper transition-metal. Ideally, this should be the very cheapest - iron(Fe) - in combination with a graphite(C)-based anode. In this context, the obvious Fe-based active cathode of choice appears to be LiFePO4. A second and in some ways even more attractive material - Li2FeSiO4 - has emerged during the course of this work. An effort has here been made to understand the Li extraction/insertion mechanism on electrochemical cycling of Li2FeSiO4. A fascinating picture has emerged (following a complex combination of Mössbauer, X-ray diffraction and electrochemical studies) in which the material is seen to cycle between Li2FeSiO4 and LiFeSiO4, but with the structure of the original Li2FeSiO4 transforming from a metastable short-range ordered solid-solution into a more stable long-range ordered structure during the first cycle. Density Functional Theory calculations on Li2FeSiO4 and the delithiated on LiFeSiO4 structure provide an interesting insight into the experimental result. Photoelectron spectroscopy was used to study the surface chemistry of both carbon-treated LiFePO4 and Li2FeSiO4 after electrochemical cycling. The surface-layer on both materials was concluded to be very thin and with incomplete coverage, giving the promise of good long-term cycling. LiFePO4 and Li2FeSiO4 should both be seen as highly promising candidates as positive-electrode materials for large-scale Li-ion battery applications.

This thesis is based on experimental studies in chemical physics. Titanium dioxide (TiO2) and phthalocyanine’s (Pc’s), interesting in many future perspectives, have been deposited as thin films and studied as follows. Information has been obtained on e.g. molecular orientation, crystal structure, depth profile of the chemical composition, electrochemical properties and electronic structure. This has been achieved by means of a combination of techniques: X-ray photoelectron spectroscopy (XPS), near edge x-ray absorption fine structure (NEXAFS), density functional theory calculations (DFT), UV-visible absorption spectroscopy (UVVIS) and cyclic voltammetry (CV). Metal-free phthalcyanine (H2Pc) has been shown to form films with different crystal structure and molecular orientation depending on deposition method, evaporation/sublimation or powder deposition, on commercial conducting glass (fluorine doped tin oxide, FTO), which is used e.g. in solar cells and organic light emitting devices (OLEDs). The unoccupied molecular orbitals are divided in x, y and z space coordinates of the molecule and also divided in inequivalent nitrogen components. The electronic structure is also studied for a sublimated titanyl phthalocyanine (TiOPc) film and related to the metal-free phthalocyanine. The ligand field around the titanium atom in TiOPc is compared with that of TiO2 to delineate the unoccupied levels recorded by means of x-ray absorption spectroscopy. Nanostructured TiO2 films were manufactured by screen printing/doctor blading on FTO. Such films were additionally covered with lutetium diphthalocyanine (LuPc2) by means of surface assembly from solution. LuPc2-, LuPc2+ and LuPc2H were identified and the stability of the electrochromic reactions in this system was monitored. Chemical vapor deposition (CVD) has been used to grow nanometer sized anatase TiO2 crystals on pre-oxidized Si (111) without formation of interfacial carbon and with an interface layer of the size of 15- 25Å. The interface layer was found to be amorphous TiSixOy with graded stoichiometry.

The work of this thesis comprises extensive Noncontact Atomic Force Microscopy (NC-AFM) characterization of clean metal-oxide (YSZ(100)/(111) and MgO(100)) and graphitic (HOPG) supports as templates for the novel, photochemically induced nucleation of cobalt oxide nanostructures, particularly Cobalt (III) Oxide. The nanostructure-support surfaces were also studied by X-ray Photoelectron Spectroscopy (XPS) to verify the nature of the supported cobalt oxide and to corroborate the surface topographic and phase NC-AFM data. Heteroepitaxial growth of Co2O3 nanostructures proves to exhibit a variety of different growth modes based on the structure of the support surface. On this basis, single-crystal support surfaces ranging from nonpolar to polar and atomically flat to highly defective and reactive were chosen, again, yielding numerous substrate-nanostructure interactions that could be probed by high-performance surface science techniques.

In this thesis, carbon supported platinum nanoparticle catalysts were prepared using PtCl4 and H2PtCl6 as starting materials and 1-heptanethiol, tert-nonyl mercaptan, 1-hexadecanethiol, 1-octadecanethiol as surfactants. These new catalysts were employed for methanol oxidation reaction which are used for direct methanol fuel cells. Tert-nonyl mercaptane was used for the first time in this type of reaction and the other surfactants were used for comparison of the catalysts performance. Cyclic voltammetry (CV), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and transmission electron microscopy (TEM) were used in order to determine the nature of the catalysts. The average platinum crystallite particle sizes of all prepared catalysts were determined by both X-ray diffraction and transmission electron microscopy. It was found that platinum crystallizes in face-centered cubic structure and the surfactant play an important role on the size of platinum nanoparticles, branch surfactant, such as tert-nonyl mercaptane, causes an increase in the size of platinum nanoparticles, about 3 nm, compared to linear surfactant, such as 1-heptanethiol, about 2 nm. The oxidation states of platinum and their ratios were determined by XPS technique. These results indicated that platinum has two different oxidation states, zero and +4, and Pt(0) to Pt(IV) ratio is about 7.5 to 2.5. In addition to this, O 1s region of XPS was also examined and found that the surface of all of the catalysts covered by adsorbed hydroxide except the catalyst which was prepared by PtCl4 and tert-nonyl mercaptane (Catalyst IIa), where adsorption of water were observed and the catalyst which was prepared by H2PtCl6 and tert-nonyl mercaptane (Catalysts IIb), where adsorption of 65% of hydroxide and 35% of water were identified. Electrochemical studies indicated that Catalyst IIa has the maximum activity (&amp / #61566 / 342 A/gPt at 0.612 V) towards methanol oxidation reaction while Catalyst IIIb (H2PtCl6 and 1-hexanethiol were used to prepare this catalyst) has the minimum activity (&amp / #61566 / 91A/gPt at 0.580V). XRD, TEM and XPS results indicated that the optimum catalyst for methanol oxidation reaction contains about 3 nm of platinum nanoparticles, adsorbed hydroxide and water on the surface of catalyst, but sulphur. These results are in agreement with the proposed mechanism.

This study focuses on various aspects of nanocrystals embedded in a dielectric matrix. In the first part of this work, a new approach with the use of Fourier Transform Infrared spectroscopy (FTIR) in the nanocrystal analysis was developed and presented. Si and Ge nanocrystals embedded in SiO2 matrix were mainly studied. This new approach is based on the analysis of structural variations of SiO2 matrix during the formation of semiconductor nanocrystlas. It is shown that the chemical and structural variations of the host matrix are directly related to the precipitation of nanocrystals in it. This correlation provides valuable information about the presences of nanocrystals in the matrix. In the second part of this work, fabrication of SiC films with and without Si nanocrystals inclusions was studied. With this aim, stoichiometric SiC and Si rich SiC thin films were fabricated by using magnetron co-sputtering and Plasma Enhanced Chemical Vapor Deposition (PECVD) techniques. For SiC films, the structural and optical analyses were performed. For Si rich SiC films, the formation conditions of Si nanocrystals were investigated. Post annealing studies were carried out to track the evolution of the SiC matrix and formation of Si nanocrystals at different temperatures. Chemical and structural properties of the SiC host matrix were investigated with FTIR spectroscopy. Optimum conditions for the fabrication of stoichiometric SiC layers were determined. The crystallography of the nanocrystals was investigated by X-Ray Diffraction (XRD). The variation of the atomic concentrations and bond formations were investigated with X-Ray Photoelectron Spectroscopy (XPS). Raman spectroscopy and Transmission Electron Microscopy (TEM) were used to verify the formation of Si nanocrystals. We have shown that both single and multilayer Si nanocrystals can be fabricated in the amorphous SiC matrix for applications such as light emitting diodes and solar cells.

In this work, two groups of carbon supported Pt-Pd catalysts have been prepared in order to investigate the effect of Pd, as a second metal, and surfactants on the catalytic activity towards methanol and ethanol oxidation reactions used in the direct methanol and ethanol fuel cells. In the first group (group a), 1- hexanethiol was used as a stabilizing agent while in the second group (group b), 1,1 dimethyl hexanethiol was utilized. Cyclic voltammetry (CV), chronoamperometry (CA), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) were used in order to determine the nature of the catalysts. The average crystalline size of the metal particles in the catalysts was explored by XRD and TEM. TEM results revealed the uniform distribution of the metal nanoparticles on carbon support with a narrow size distribution in the range of 3.0 to 3.7 nm and the average crystalline sizes of metal particles for group &ldquo / b&rdquo / catalysts were larger than that of group &ldquo / a&rdquo / catalysts which can be explained by the surfactant effect. These results were in good agreement with XRD data. The oxidation states of platinum (Pt(0) and Pt(IV)) and palladium (Pd(0) and Pd(II)) and their ratios were investigated by XPS and for the most active catalyst, catalyst Ib, these ratios were found to be as 6.94 and 13.7, respectively. Electrochemical activities of the catalysts towards methanol and ethanol oxidation reactions were recorded and compared with that of Pt/C and the commercial Pt (ETEK 20 %wt) catalysts. The results indicated that the group &lsquo / b&rsquo / catalyst has greater catalytic activities than that of group &lsquo / a&rsquo / catalysts. Catalyst Ib comes into prominence as the most active catalyst due to its superior characteristics that it possess such as highest extent of alloying with respect to the palladium amount used, active surface area, CO-tolerance, stability and Pt (0) to Pt (IV) and Pd (0) to Pd (II) ratios.

Complex oxides are an intriguing field of solid-state research, as they can exhibit a wide variety of functional properties, such as ferroelasticity, ferroelectricity, ferro- and antiferromagnetism or an even more complicated type of magnetic ordering, the combination or interaction of those ferroic properties (multiferroicity), high spin polarization, or high-temperature superconductivity. Thus they are prospective candidates for future materials in microelectronics. It is a matter of fact that the performance of such oxide-based devices depends mainly on transport properties, which in turn depend on the distribution and density of intrinsic or extrinsic electronic interface states across the device structure. The present thesis focuses on the identification and characterization of such electronic properties by two different photoassisted spectroscopy techniques: surface photovoltage spectroscopy and photoelectron spectroscopy. This work especially deals with perovskite oxides, namely with the model perovskite strontium titanate (SrTiO3) as a substrate and three differently doped lanthanum manganite thin films (10-15 nm thickness) grown by pulsed laser deposition (PLD) on the SrTiO3 substrate(La0.7Sr0.3MnO3, La0.7Ca0.3MnO3, La0.7Ce0.3MnO3). The first part aims at the identification of electronic surface and interface states at the free SrTiO3 surface as well as at the three different lanthanum manganite/SrTiO3 interfaces. For that purpose three different experimental realizations of the surface photovoltage spectroscopy technique were implemented and employed: photoelectron spectroscopy under additional optical excitation, the capacitive detection of the photoinduced displacement current in a parallel-plate capacitor geometry under modulated optical excitation, and the classical Kelvin probe technique. The methods are evaluated comparatively with respect to their suitability to analyze the given oxidic interfaces. The main result of this first part is a map of the energetic positions and relaxation time constants of the surface states at the SrTiO3 surface as well as of the interface states at the lanthanum manganite/SrTiO3 interfaces within the SrTiO3 bandgap. The interface states were classified into film- and substrate-induced states and it could be demonstrated that an appropriate annealing procedure can dramatically decrease their densities. The second part tackles the problem of the manganese valence and the doping type of di- and tetravalent-ion-doped LaMnO3. The question whether the insulating parent compound LaMnO3 becomes an electron-doped semiconductor after doping with tetravalent cations such as Ce4+ - which would be in analogy to the well-established hole doping after partial substitution of La3+ by divalent cations such as Sr2+ or Ca2+ - has been discussed controversially in the literature so far. Due to the physics of the manganite crystal lattice the question can also be formulated in a different way: Can part of the manganese ions be driven from the Mn3+ state towards the Mn2+ state without any crystal instabilities or phase separation phenomena? In order to contribute to the clarification of this question, an extensive X-ray- and UV-photoelectron spectroscopy (XPS/UPS) investigation was performed. The three differently doped lanthanum manganite thin films were comparatively studied considering the exchange splitting of the Mn 3s core level line, which is a linear function of the Mn valence, as measured by XPS and the work function as extracted from UPS. All measurements were performed at different states of deoxygenation after heating in ultrahigh vacuum and reoxidation after heating in a pure oxygen atmosphere. Strong evidence for electron doping of the La0.7Ce0.3MnO3 film after deoxygenation was found. Furthermore, the reversible tunability of the Mn valence by variation of the oxygen content could be demonstrated for both tetravalent- and divalent-ion-doped lanthanum manganite films. / Oxidische Komplexverbindungen können eine Vielzahl an funktionellen Eigenschaften, wie z.B. Ferroelastizität, Ferroelektrizität, Ferro- und Antiferromagnetismus sowie kompliziertere magnetische Ordnungen, die Kombination und Interaktion solcher ferroischer Eigenschaften (Multiferroizität), hohe Spinpolarisation oder Hochtemperatursupraleitung aufweisen und gelten daher als aussichtsreiche Materialien für die zukünftige Mikroelektronik. Entscheidend für die Funktionsfähigkeit oxidischer Bauelemente sind deren elektronische Transporteigenschaften, die in äußerst sensibler Weise von der Verteilung und Dichte von ex- oder intrinsischen elektronischen Defektzuständen an Grenz- und Oberflächen innerhalb der Bauelementstruktur abhängen. Die vorliegende Arbeit beschäftigt sich mit der Spektroskopie solcher elektronischer Eigenschaften mittels photonenbasierter Methoden. Im Fokus stehen dabei perowskitische Oxide , speziell das Modellperowskit Strontiumtitanat (SrTiO3) als Substrat und darauf mittels gepulster Laserdeposition (PLD) abgeschiedene dünne Filme (10-15 nm Dicke) dotierter Lanthanmanganate (La0.7Sr0.3MnO, La0.7Ca0.3MnO3, La0.7Ce0.3MnO3). Im Rahmen einer halbleiterphysikalischen Interpretation widmet sich der erste Teilder Identifikation elektronischer Ober- und Grenzflächenzustände an der SrTiO3-Oberfläche sowie an verschiedenen Lanthanmanganat/SrTiO3-Grenzflächen mittels dreier unterschiedlicher experimenteller Methoden zur Vermessung der Oberflächenphotospannung: der Photoelektronenspektroskopie unter zusätzlicher optischer Anregung, einer kapazitiven Detektionsmethode in Plattenkondensatorgeometrie unter modulierter optischer Anregung und der optischen Kelvin-Sonde. Neben einem auf die bei oxidischen Ober- und Grenzflächen auftretenden besonderen Herausforderungen zugeschnittenen Methodenvergleich werden Grenzflächenzustände bezüglich ihrer energetischen Position in der Bandlücke des SrTiO3 und ihres Relaxationsverhaltens analysiert, als substrat- oder filminduziert klassifiziert, und die Verringerung ihrer Dichte nach geeigneter Ausheilprozedur wird nachgewiesen. Der zweite Teil der Arbeit befasst sich mit der in der Literatur bisher kontrovers diskutierten Frage, ob sich die isolierende Stammverbindung LaMnO3 durch Dotierung mit tetravalenten Kationen, wie z.B. Ce4+, in einen elektronendotierten Halbleiter verwandeln lässt - analog zur Herstellung lochdotierter Lanthanmanganate durch Dotierung mit divalenten Kationen, wie z.B. Sr2+ oder Ca2+. Die Frage ist äquivalent zur Betrachtung, ob unter Beibehaltung der Stabilität des Kristallgitters ein Teil der Manganionen vom Mn3+-Zustand in den Mn2+-Zustand übergehen kann. Um einen Beitrag zur Klärung dieses Problems zu leisten, wurden als elektronisch sensitive Methoden die Röntgen- und UV-Photoelektronenspektroskopie (XPS/UPS) gewählt. Die oben genannten Lanthanmanganatfilme wurden dazu hinsichtlich der Austauschaufspaltung der Mangan-3s-Linie im XP-Spektrum, die in linearer Weise von der Manganvalenz abhängt, und der anhand der Breite des UP-Spektrums ermittelten Austrittsarbeit jeweils nach Reinigung der Oberfläche im Ultrahochvakuum (UHV) vergleichend untersucht. Die Messungen wurden nach unterschiedlich starker Desoxidation durch Heizen im UHV und Reoxidierung durch Heizen in Sauerstoffatmosphäre durchgeführt. Es konnte nachgewiesen werden, dass eine Elektronendotierung des La0.7Ce0.3MnO3-Films bei geeigneter Einstellung des Sauerstoffgehalts tatsächlich möglich ist. Außerdem wurde gezeigt, dass sich sowohl in di- als auch in tetravalent dotierten Lanthanmanganatfilmen die Manganvalenz und damit der Dotierungstyp reversibel durchstimmen lässt.

<p>Catalytic combustion is an environmentally benign technologywhich has recently reached the stage of commercialization.Palladium is the catalyst of choice when considering gasturbines fuelled with natural gas because of its superioractivity for methane oxidation. Several fundamental issues arestill open and their understanding would result in animprovement of the technology. Hence, the work presented inthis thesis aims at the identification of some of theparameters which govern the combustion activity ofpalladium-based catalysts.</p><p>The first part of this work gives a background to catalyticcombustion and a brief comparison with other existingtechnologies. Paper I reviews some of the issues related tomaterial development and combustor design.</p><p>The second part of this thesis consists of an experimentalinvestigation on palladium-based catalysts. The influence ofthe preparation method onthe properties of these catalystmaterials is investigated in Paper II. Paper III examines theactivity of the following catalysts: Pd/Al2O3, Pd/Ba-Al2O3 andPd/La-Al2O3. Specific attention is given to the metal-supportinteraction which strongly affects the combustion activity ofpalladium. The effect of doping of the support by addition ofcerium is reported in Paper IV.</p><p>Finally, the deactivation of combustion catalysts isconsidered. The various deactivation processes which may affecthigh temperature combustion catalysts are reviewed in Paper V.Paper VI focuses on the poisoning of supported palladiumcatalysts by sulphur species. Palladium exhibits a higherresistance to sulphur poisoning than transition metals.Nevertheless, the nature of the support material plays animportant role and may entail a severe loss of activity whensulphur is present in the fuel-air mixture entering thecombustion chamber.</p><p><b>Keywords</b>: catalytic combustion, gas turbine, methane,palladium, alumina, barium, lanthanum, oxidation, preparation,temperature-programmed oxidation (TPO), decomposition,reoxidation, X-ray photoelectron spectroscopy (XPS),metal-support interaction, deactivation, sulphur, poisoning.The cover illustration is a TEM picture of a 100 nm palladiumparticle supported on alumina</p>

<p>In the growing field of spintronics there is a strong need for development of flexible lightweight semi-conducting magnets. Molecular organic-based magnets are attractive candidates since it is possible to tune their properties by organic chemistry, making them so-called “designer magnets”. Vanadium tetracyanoethylene, V(TCNE)_x, is particularly interesting since it is a semiconductor with Curie temperature above room temperature (T_C~400 K). The main problem with these organic-based magnets is that they are extremely air sensitive. This thesis reports on the frontier electronic structure of the V(TCNE)_x by characterization with photoelectron spectroscopy (PES) and near edge x-ray absorption fine structure (NEXAFS) spectroscopy. It also presents a new and more flexible preparation method of this class of organic-based thin film magnets. The result shows improved air stability of the V(TCNE)_x prepared with this method as compared to V(TCNE)_x prepared by hitherto used methods.</p>