Fármacos pouco solúveis em água tendem a possuir baixa biodisponibilidade. Diversos métodos têm sido estudados para promover o aumento da solubilidade em água de fármacos pouco solúveis. As dispersões sólidas têm sido pesquisadas como uma estratégia de aumentar a solubilidade em água e melhorar o desempenho destes fármacos na biodisponibilidade, entretanto os mecanismos completamente elucidados parecem variar da combinação do fármaco e do polímero, bem como do método de obtenção empregado. No presente estudo, através da técnica de evaporação do solvente desenvolveu-se dispersões sólidas de loratadina em polivinilpirrolidona a fim de melhorar a solubilidade do fármaco. / Poorly water soluble drugs tend to have low bioavailability. Several methods have been studied to promote increased water solubility of poorly soluble drugs. Solid dispersions have been investigated as a strategy to increase the water solubility and improve performance on the bioavailability of these drugs, however elucidated the mechanisms seem to vary the combination of drug and polymer and production method employed. In this study, using the technique of solvent evaporation was developed from solid dispersions in polyvinylpyrrolidone loratadine to improve the solubility of the drug.

Indiana University-Purdue University Indianapolis (IUPUI) / The studies of rechargeable lithium-sulfur (Li-S) batteries are included in this thesis. In the first part of this thesis, a linear sweep voltammetry method to study polysulfide transport through separators is presented. Shuttle of polysulfide from the sulfur cathode to lithium metal anode in rechargeable Li-S batteries is a critical issue hindering cycling efficiency and life. Several approaches have been developed to minimize it including polysulfide-blocking separators; there is a need for measuring polysulfide transport through separators. We have developed a linear sweep voltammetry method to measure the anodic (oxidization) current of polysulfides crossed separators, which can be used as a quantitative measurement of the polysulfide transport through separators. The electrochemical oxidation of polysulfide is diffusion-controlled. The electrical charge in Coulombs produced by the oxidation of polysulfide is linearly related to the concentration of polysulfide within a certain range (≤ 0.5 M). Separators with a high porosity (large pore size) show high anodic currents, resulting in fast capacity degradation and low Coulombic efficiencies in Li-S cells. These results demonstrate this method can be used to correlate the polysulfide transport through separators with the separator structure and battery performance, therefore provide guidance for developing new separators for Li-S batteries. The second part includes a study on improving cycling performance of Li/polysulfide batteries by applying a functional polymer on carbon current collector. Significant capacity decay over cycling in Li-S batteries is a major impediment for their practical applications. Polysulfides Li2Sx (3 < x ≤ 8) formed in the cycling are soluble in liquid electrolyte, which is the main reason for capacity loss and cycling instability. Functional polymers can tune the structure and property of sulfur electrodes, hold polysulfides, and improve cycle life. We have examined a polyvinylpyrrolidone-modified carbon paper (CP-PVP) current collector in Li/polysulfide cells. PVP is soluble in the electrolyte solvent, but shows strong affinity with lithium polysulfides. The retention of polysulfides in the CP-PVP current collector is improved by ~50%, which is measured by a linear sweep voltammetry method. Without LiNO3 additive in the electrolyte, the CP-PVP current collector with 50 ug of PVP can significantly improve cycling stability with a capacity retention of > 90% over 50 cycles at C/10 rate. With LiNO3 additive in the electrolyte, the cell shows a reversible capacity of > 1000 mAh g ⁻¹ and a capacity retention of > 80% over 100 cycles at C/5 rate. The third part of this thesis is about a study on a binder-free sulfur/carbon composite electrode prepared by a sulfur sublimation method for Li-S batteries. Sulfur nanoparticles fill large pores in a carbon paper substrate and primarily has a monoclinic crystal structure. The composite electrode shows a long cycle life of over 200 cycles with a good rate performance in Li-S batteries.

Este trabalho visa estudar a viabilidade do emprego de processos oxidativos avancados na degradacao de solucoes aquosas de polimeros que sao comumente utilizados em aplicacoes industriais e estao presentes em seus efluentes. Para maior entendimento das reacoes envolvidas no processo oxidativo utilizou-se modelagem molecular nos calculos de constantes cineticas. Na parte experimental estudou-se a degradacao de polietilenoglicol (PEG), polivinilpirrolidona (PVP) e poliacrilamida (PAM) pelos processos foto-Fenton e UV/H2O2. Realizaram-se analises de carbono organico dissolvido (COD), cromatografia liquida de alto desempenho (HPLC) e cromatografia de permeacao em gel (GPC). Observou-se separacao de fases para PVP e PAM, o que contribuiu para uma remocao final de COD de ate 85%. Nas analises de HPLC foram detectados como intermediarios da reacao os acidos: oxalico, formico, malonico e acetico. Os resultados de GPC indicaram comportamentos distintos das distribuicoes de pesos moleculares em funcao do tempo de reacao para os processos UV/H2O2 e foto- Fenton. No conjunto, os resultados comprovam a viabilidade dos processos estudados na degradacao destes polimeros, embora a analise de intermediarios para PAM nao tenha sido conclusiva quanto a formacao de acrilamida. A modelagem molecular confirma que a reacao de abstracao de hidrogenio de uma cadeia polimerica pelos radicais alquilperoxila e de fato a etapa mais lenta do processo oxidativo para PEG e PAM. Para PAM os resultados da modelagem mostram que o ataque dos radicais hidroxila acontece preferencialmente no hidrogenio ligado ao carbono terciario e que a abstracao de hidrogenio do grupo lateral amida parece pouco viavel, ou acontece por um mecanismo diferente do modelado. A reacao de formacao da acrilamida de acordo com o mecanismo proposto tambem apresentou uma constante cinetica muito baixa, o que esta de acordo com os resultados experimentais, ja que nao foi detectada acrilamida como produto da degradacao de poliacrilamida pelos processos foto-Fenton e UV/H2O2, com limite de deteccao de 50 ppb. / The aim of this work is to apply advanced oxidative processes to study the degradation of industrial wastewater containing water-soluble polymers. Kinetic constants of reactions involved in the oxidation processes were calculated by molecular modeling. In the experimental part the degradation of polyvinylpirrolidone (PVP), polyacrylamide (PAM) and polyethyleneglycol (PEG) was studied by photo-Fenton and UV/H2O2 processes. Intermediates of the degradation processes were identified by HPLC and the molecular weight distribution was monitored by GPC. In the experiments with PAM and PVP phase separation was observed, and more than 85% of the DOC was removed. The following intermediate acids were identified: acetic, malonic, formic and oxalic. The molecular weight distribution curves measured by GPC indicate that distinct reaction paths exist for each process studied, although the analysis of intermediates formed during the degradation of PAM was not conclusive with respect to acrylamide formation. The kinetic constants for the reactions involving hydrogen abstraction from PEG chain by hydroxyl and alkylperoxy radicals were calculated. The molecular modeling results confirm that hydrogen abstraction from polymeric chain by alkylperoxy radicals is the determinant step in the oxidation process for PEG and PAM. Polyacrylamide possesses three sites for attack by hydroxyl radicals and the favored path is the abstraction of tertiary hydrogen atom, followed by secondary hydrogen. The abstraction of the amide hydrogen was more difficult. The mechanism proposed for acrylamide formation was not the preferential reaction path. This was expected since acrylamide was not detected in the experiments with a limit detection of 50 ppb.

Crystallization of water or water-encaged gas molecules occurs when nuclei reach a critical size. Certain antifreeze proteins (AFPs) can inhibit the growth of both of these, with most representations conceiving of an embryonic crystal with AFPs adsorbing to a preferred face, resulting in a higher kinetic barrier for molecule addition. We have examined AFP-mediated inhibition of ice and clathrate hydrate crystallization, and these observations can be both explained and modeled using this mechanism for AFP action. However, the remarkable ability of AFPs to eliminate „memory effect‟ (ME) or the faster reformation of clathrate hydrates after melting, prompted us to examine heterogeneous nucleation. The ubiquitous impurity, silica, served as a model nucleator hydrophilic surface. Quartz crystal microbalance-dissipation (QCM-D) experiments indicated that an active AFP was tightly adsorbed to the silica surface. In contrast, polyvinylpyrrolidone (PVP) and polyvinylcaprolactam (PVCap), two commercial hydrate kinetic inhibitors that do not eliminate ME, were not so tightly adsorbed. Significantly, a mutant AFP (with no activity toward ice) inhibited THF hydrate growth, but not ME. QCM-D analysis showed that adsorption of the mutant AFP was more similar to PVCap than the active AFP. Thus, although there is no evidence for „memory‟ in ice reformation, and the structures of ice and clathrate hydrate are distinct, the crystallization of ice and hydrates, and the elimination of the more rapid recrystallization of hydrates, can be mediated by the same proteins.

Este trabalho visa estudar a viabilidade do emprego de processos oxidativos avancados na degradacao de solucoes aquosas de polimeros que sao comumente utilizados em aplicacoes industriais e estao presentes em seus efluentes. Para maior entendimento das reacoes envolvidas no processo oxidativo utilizou-se modelagem molecular nos calculos de constantes cineticas. Na parte experimental estudou-se a degradacao de polietilenoglicol (PEG), polivinilpirrolidona (PVP) e poliacrilamida (PAM) pelos processos foto-Fenton e UV/H2O2. Realizaram-se analises de carbono organico dissolvido (COD), cromatografia liquida de alto desempenho (HPLC) e cromatografia de permeacao em gel (GPC). Observou-se separacao de fases para PVP e PAM, o que contribuiu para uma remocao final de COD de ate 85%. Nas analises de HPLC foram detectados como intermediarios da reacao os acidos: oxalico, formico, malonico e acetico. Os resultados de GPC indicaram comportamentos distintos das distribuicoes de pesos moleculares em funcao do tempo de reacao para os processos UV/H2O2 e foto- Fenton. No conjunto, os resultados comprovam a viabilidade dos processos estudados na degradacao destes polimeros, embora a analise de intermediarios para PAM nao tenha sido conclusiva quanto a formacao de acrilamida. A modelagem molecular confirma que a reacao de abstracao de hidrogenio de uma cadeia polimerica pelos radicais alquilperoxila e de fato a etapa mais lenta do processo oxidativo para PEG e PAM. Para PAM os resultados da modelagem mostram que o ataque dos radicais hidroxila acontece preferencialmente no hidrogenio ligado ao carbono terciario e que a abstracao de hidrogenio do grupo lateral amida parece pouco viavel, ou acontece por um mecanismo diferente do modelado. A reacao de formacao da acrilamida de acordo com o mecanismo proposto tambem apresentou uma constante cinetica muito baixa, o que esta de acordo com os resultados experimentais, ja que nao foi detectada acrilamida como produto da degradacao de poliacrilamida pelos processos foto-Fenton e UV/H2O2, com limite de deteccao de 50 ppb. / The aim of this work is to apply advanced oxidative processes to study the degradation of industrial wastewater containing water-soluble polymers. Kinetic constants of reactions involved in the oxidation processes were calculated by molecular modeling. In the experimental part the degradation of polyvinylpirrolidone (PVP), polyacrylamide (PAM) and polyethyleneglycol (PEG) was studied by photo-Fenton and UV/H2O2 processes. Intermediates of the degradation processes were identified by HPLC and the molecular weight distribution was monitored by GPC. In the experiments with PAM and PVP phase separation was observed, and more than 85% of the DOC was removed. The following intermediate acids were identified: acetic, malonic, formic and oxalic. The molecular weight distribution curves measured by GPC indicate that distinct reaction paths exist for each process studied, although the analysis of intermediates formed during the degradation of PAM was not conclusive with respect to acrylamide formation. The kinetic constants for the reactions involving hydrogen abstraction from PEG chain by hydroxyl and alkylperoxy radicals were calculated. The molecular modeling results confirm that hydrogen abstraction from polymeric chain by alkylperoxy radicals is the determinant step in the oxidation process for PEG and PAM. Polyacrylamide possesses three sites for attack by hydroxyl radicals and the favored path is the abstraction of tertiary hydrogen atom, followed by secondary hydrogen. The abstraction of the amide hydrogen was more difficult. The mechanism proposed for acrylamide formation was not the preferential reaction path. This was expected since acrylamide was not detected in the experiments with a limit detection of 50 ppb.

Made available in DSpace on 2015-08-19T13:52:53Z (GMT). No. of bitstreams: 2 5.pdf: 3872815 bytes, checksum: 455a971c4daecfecb98403b32be14999 (MD5) license.txt: 1748 bytes, checksum: 8a4605be74aa9ea9d79846c1fba20a33 (MD5) Previous issue date: 2012 / Fundação Oswaldo Cruz. Instituto de Tecnologia em Fármacos/Farmanguinhos. Rio de Janeiro, RJ, Brasil. / O efavirenz (EFA) está classificado como um fármaco de classe II, pois é pouco hidrossolúvel e altamente permeável pelo trato gastrointestinal. Estas duas características básicas são essenciais para sua biodisponibilidade. Assim, a escolha de uma formulação adequada para esse fármaco é essencial no desenvolvimento de comprimidos, para garantir melhor disponibilização no trato gastrointestinal, de forma a alcançar a biodisponibilidade e o efeito terapêutico desejados. Nesse trabalho, oEFA e a mistura EFA:polivinilpirrolidona (PVP), preparados por processos de micronização com intuito de aumentar a dissolução do fármaco, foram espectroscopicamente estudados e caracterizados. No caso do EFA sua estrutura foi modelada usando o método B3LYP com intuito de auxiliar na análise dos resultados experimentais. A caracterização espectroscópica foi realizada utilizando diversas técnicas como infravermelho (IV) e ressonância magnética nuclear (RMN)em solução e de sólidos. A análise térmica por calorimetria diferencial de varredura(DSC) e a análise termogravimétrica (TGA) mostraram que os processos de comicronização não afetaram a estrutura cristalina do fármaco puro e nem a do fármaco nas misturas. A RMN comprovou a integridade dos mesmos, em solução eno estado sólido, indicando que o EFA encontra-se dimerizado. Os estudos de RMN também mostraram que, tanto no estado líquido quanto no sólido, ocorrem interações intermoleculares via ligação de hidrogênio do EFA com a PVP. Os espectros de RMN de sólido indicaram que ocorre dissolução parcial do EFA na matriz polimérica / Efavirenz (EFA) is classified as a class II drug because it is poorly water soluble and highly permeable through the gastrointestinal tract. These two basic characteristics are essential for its bioavailability. Thus, the choice of a suitable formulation for this drug is essential in the development of tablets to ensure better gastrointestinal tract in order to achieve both the bioavailability and the therapeutic effect desired. In this work, EFA and the blends EFA:polyvinylpyrrolidone (PVP) were prepared by spray drying and grinding processes in order to increase the solubility of the drug, were studied and characterized spectroscopically. In the case of EFA its structure was modeled using the B3LYP in order to aid the analysis of the experimental results. The spectroscopic characterization was performed using various techniques such as infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR) in solution and solid state. Thermal analysis by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), showed that the micronization process neither affected the crystal structure of the pure drug nor the drug in blends. NMR confirmed the integrity of the solution and the solid form and identified that the EFA is dimerized. The NMR studies also showed that both liquid and solid interactions occur via intermolecular hydrogen bonding of EFA with PVP. The NMR spectra indicated that occurs the solid partial dissolution of the EFA in the polymer matrix.

This diploma thesis focuses on the fabrication of ceramic fibres by electrospinning. The theoretical part of the thesis summarizes the currently available information regarding ceramic fibres, their properties, applications and fabrication. The theoretical part also describes the process of electrospinning as one of the most frequently used methods of nanofibre fabrication, as well as the parametres influencing this process. The experimental part is aimed at the fabrication of ceramic fibres based on titania, pure non-doped zirconia and yttria-doped zirconia by electrospinning and at the characterization of thus fabricated fibres. Ceramic precursors based on propoxide and polyvinylpyrrolidone were subjected to electrospinning. The experimental part of this diploma thesis also describes the influence of precursor composition, process conditions and calcination temperature on the morphology and phase composition of the fibres. Precursors were characterized by viscosity measurements. Thermogravimetric analysis (TGA), Röntgen analysis (RTG) and scanning electron microscopy (SEM) were used to describe the fibres. By performing electrospinning of precursors based on titanium propoxide and subsequent calcination at 500-1300 °C, TiO2 fibres with thickness of 100-2500 nm were fabricated. The phase composition changed with calcination temperature from 500 °C from anatase phase through rutile blend to pure rutile at 900 °C. By performing electrospinning of precursors based on zirconium propoxide and subsequent calcination at 550-1100 °C, 0 – 8 mol% Y2O3 doped ZrO2 fibres with thickness of 50-1000 nm were fabricated. An analysis of fibres based on non-doped ZrO2, calcined at 550 °C showed a composition of predominantly monoclinic phase. An analysis of 3 or 8 mol% Y2O3 doped ZrO2 fibres calcined at 900 °C showed a composition of predominantly tetragonal phase or purely cubic phase, respectively. With the increasing calcination temperature, the morphology of the fibres changed from porous nanostructure to chain-like non-porous structure consisting of micrometer grains of TiO2 or ZrO2. The ZrO2 fibres calcined at 700 °C remained flexible as well as the spun ones, while their fragility increased with the increase in calcination temperature.

As folhas de Maytenus ilicifolia são amplamente utilizadas na medicina tradicional brasileira no tratamento de distúrbios gástricos. Após a comprovação de sua eficácia e segurança, a referida droga vegetal tem sido objeto de diversos estudos com a finalidade de estabelecer parâmetros para o controle de qualidade. Neste sentido, foi avaliada a viabilidade do desenvolvimento de um método analítico fundamentado na precipitação de taninos empregando povidona como agente seqüestrante. Os dados revelaram que a remoção de taninos em solução é satisfatória quando empregada a povidona insolúvel. Foi observado que o polímero também é capaz de precipitar outros polifenóis além dos taninos presentes na solução extrativa de M. ilicifolia. Entretanto, as interações do polímero ocorrem preferencialmente com os derivados catéquicos. Adicionalmente foi desenvolvido e validado um método por CLAE para separação e quantificação de catequina e epicatequina em produtos derivados de M. ilicifolia. Não foram detectadas variações nas áreas dos picos ou nos tempos de retenção durante os ensaios de avaliação do método, sugerindo que as condições cromatográficas empregadas são satisfatórias. Para viabilizar a preparação de produto seco por aspersäo (PSA) em torre de secagem piloto munida de aspersor rotatório, foi necessária a concentração da solução extrativa. A operação foi realizada sob pressão reduzida até alcangar um teor de sólidos mínimo de 15 % (m/m). A operação de secagem da solução concentrada apresentou rendimento de 90 % e o PSA obtido apresentou partículas esféricas, com superfície rugosa e tamanho médio de 22,5 um. A caracterização tecnológica do material revelou que as suas propriedades tecnológicas, tais como, densidades, compressibilidade e fluxo, foram incrementadas quando comparados com o produto preparado em equipamento de bancada. Entretanto, estas modificações não foram suficientes para viabilizar sua compressão direta. Assim sendo, o material foi compactado em máquina de comprimir e em rolos para produção de grânulos. A análise do perfil compressional do PSA e dos granulados, empregando o modelo de Heckel, revelou que o aumento da força de compactação durante a operação de granulação foi o principal responsável pela diminuição no potencial de deformação plástica dos grânulos. Como conseqüência, a recompressão dos grânulos em máquina de comprimir originou compactos com dureza inferior àqueles preparados diretamente do complexo farmacêutico. Enquanto o PSA apresentou reduzida tendência ao rearranjo particular nos estágios iniciais da compressão, os grânulos sofreram intensa reacomodação decorrente da fragmentação e formação de novas pontes, assumindo comportamento plástico em pressões de compressão mais elevadas. Por fim, comprimidos contendo teor elevado de granulado de PSA foram preparados utilizando como adjuvantes a celulose microcristalina, o dióxido de silício coloidal e a croscarmelose sódica. A influência da concentração de dióxido de silício coloidal e croscarmelose sódica na formulação, sobre as respostas de dureza, friabilidade e tempo de desintegração dos comprimidos foram avaliadas através de um Desenho Composto Central. Os dados experimentais foram analisados estatisticamente, utilizando os modelos matemáticos para gerar superfícies de resposta. Os resultados indicaram que a concentração de dióxido de silício coloidal foi inversamente relacionada às respostas de dureza e friabilidade, enquanto que a concentração de croscarmelose sódica foi a principal responsável pela redução no tempo de desintegração. As condições ótimas foram selecionadas através da sobreposição dos gráficos, buscando uma formulação com menor tempo de desintegração, menor friabilidade e o máximo de dureza. A formulação eleita deve conter 1,2 % (m/m) de dióxido de silício coloidal e 5,0 % (m/m) de croscarmelose sódica. Nestas condições os comprimidos apresentaram dureza de 107,9 N, friabilidade de 0,56 % (m/m) e desintegração máxima em 6,8 min. / The leaves of Maytenus ilicifolia are widely used within the traditional Brazilian medicine due to its properties against gastric disorders. Once proved its efficacy and safety, this vegetable drug has been the object of several studies to establish the basis for quality control. Taking this into consideration, it was necessary to evaluate the feasibility of developing an analytical method based on the precipitation of tannins, by using polyvinylpyrrolidone for precipitation. The data have shown that the removal of the tannins in solution was successful when insoluble polyvinylpyrrolidone was used. Hereby it was observed that the polymer has also the ability to precipitate other polyphenols besides the tannins from the aqueous solution of M. ilicifolia. However, the interactions of the polymer happened mostly with the condensed tannins. Further it was developed and also validated an HPLC method to separate and quantify catechin and epicatechin present in aqueous extracts of M. ilicifolia. No significant variations of peak areas or retention times were observed when the evaluation of the method was executed, showing satisfactory chromatographic conditions. In order to make a spray dried extract (SDE) using a spray-drier fitted out with a rotary atomizer, it was necessary to concentrate the extractive solution. This operation had been performed under reduced pressure until a content of 15 % solids was achieved. The drying of the concentrated solution lead to a yield of 90 %, and the obtained SDE presented spherical particles, which have a rough surface and a mean particle size of 22,51.1.m. The technological characterization of the SDE showed that attributes such as densities (tap and bulk), compressibility and flow, have been improved when compared to the product prepared using a mini spray-drier supplied with a pneumatic nozzle. However, these modifications were not enough to enable its direct compression. Therefore, the material was compacted to produce granules after slugging or roller compaction, The compressional analysis of the SDE and each granule batch using the Heckel equation proved that the increase in the compaction force once processing the granulation was the main factor to reduce the material's ability to undergo plastic deformation. Consequently, the recompression of the granules in a tablet press led to compacts with a lower crushing strength compared to that prepared by direct compression of the pharmaceutical complex. Whereas the SDE has shown a reduced tendency to particle rearrangement at early stage of compression, the granules showed an intense fragmentation and rebound behavior, presenting a plastic behavior when higher compaction pressures were used. Finally, tablets containing a high dose of granulated spray dried extract of M. ilicifolia were prepared by using the following excipients: microcrystalline cellulose (filler/binder), colloidal silicon dioxide (glidant and moisture adsorber) and cross-linked carboxymethylcellulose (disintegrant). The influences of colloidal silicon dioxide (CSD) and cross-linked carboxymethylcellulose (CMC-Na) on the tablet hardness, disintegration time and friability were evaluated by a central composite design. The data were analyzed statistically and mathematical models were used to create response surfaces. The results have indicated that the concentration of CSD shows an inverse relation to the responses of hardness and friability, while the concentration of CMC-Na was the most important factor that caused a reduction of the time necessary for total disintegration. The optimal conditions for processing were chosen by the overlapping of graphics, taking into consideration that the formulation should present a minimum of disintegration time, lower friability and a maximum of hardness. Thus, it was found that the best formulation should have a content of 1.2% (w/w) of CSD and 5.0% (w/w) of CMC-Na. Regarding these conditions, the tablets have shown a hardness of 107.9 N, friability of 0.56% (w/w) and a disintegration time of 6.8 min.

No description available.

As folhas de Maytenus ilicifolia são amplamente utilizadas na medicina tradicional brasileira no tratamento de distúrbios gástricos. Após a comprovação de sua eficácia e segurança, a referida droga vegetal tem sido objeto de diversos estudos com a finalidade de estabelecer parâmetros para o controle de qualidade. Neste sentido, foi avaliada a viabilidade do desenvolvimento de um método analítico fundamentado na precipitação de taninos empregando povidona como agente seqüestrante. Os dados revelaram que a remoção de taninos em solução é satisfatória quando empregada a povidona insolúvel. Foi observado que o polímero também é capaz de precipitar outros polifenóis além dos taninos presentes na solução extrativa de M. ilicifolia. Entretanto, as interações do polímero ocorrem preferencialmente com os derivados catéquicos. Adicionalmente foi desenvolvido e validado um método por CLAE para separação e quantificação de catequina e epicatequina em produtos derivados de M. ilicifolia. Não foram detectadas variações nas áreas dos picos ou nos tempos de retenção durante os ensaios de avaliação do método, sugerindo que as condições cromatográficas empregadas são satisfatórias. Para viabilizar a preparação de produto seco por aspersäo (PSA) em torre de secagem piloto munida de aspersor rotatório, foi necessária a concentração da solução extrativa. A operação foi realizada sob pressão reduzida até alcangar um teor de sólidos mínimo de 15 % (m/m). A operação de secagem da solução concentrada apresentou rendimento de 90 % e o PSA obtido apresentou partículas esféricas, com superfície rugosa e tamanho médio de 22,5 um. A caracterização tecnológica do material revelou que as suas propriedades tecnológicas, tais como, densidades, compressibilidade e fluxo, foram incrementadas quando comparados com o produto preparado em equipamento de bancada. Entretanto, estas modificações não foram suficientes para viabilizar sua compressão direta. Assim sendo, o material foi compactado em máquina de comprimir e em rolos para produção de grânulos. A análise do perfil compressional do PSA e dos granulados, empregando o modelo de Heckel, revelou que o aumento da força de compactação durante a operação de granulação foi o principal responsável pela diminuição no potencial de deformação plástica dos grânulos. Como conseqüência, a recompressão dos grânulos em máquina de comprimir originou compactos com dureza inferior àqueles preparados diretamente do complexo farmacêutico. Enquanto o PSA apresentou reduzida tendência ao rearranjo particular nos estágios iniciais da compressão, os grânulos sofreram intensa reacomodação decorrente da fragmentação e formação de novas pontes, assumindo comportamento plástico em pressões de compressão mais elevadas. Por fim, comprimidos contendo teor elevado de granulado de PSA foram preparados utilizando como adjuvantes a celulose microcristalina, o dióxido de silício coloidal e a croscarmelose sódica. A influência da concentração de dióxido de silício coloidal e croscarmelose sódica na formulação, sobre as respostas de dureza, friabilidade e tempo de desintegração dos comprimidos foram avaliadas através de um Desenho Composto Central. Os dados experimentais foram analisados estatisticamente, utilizando os modelos matemáticos para gerar superfícies de resposta. Os resultados indicaram que a concentração de dióxido de silício coloidal foi inversamente relacionada às respostas de dureza e friabilidade, enquanto que a concentração de croscarmelose sódica foi a principal responsável pela redução no tempo de desintegração. As condições ótimas foram selecionadas através da sobreposição dos gráficos, buscando uma formulação com menor tempo de desintegração, menor friabilidade e o máximo de dureza. A formulação eleita deve conter 1,2 % (m/m) de dióxido de silício coloidal e 5,0 % (m/m) de croscarmelose sódica. Nestas condições os comprimidos apresentaram dureza de 107,9 N, friabilidade de 0,56 % (m/m) e desintegração máxima em 6,8 min. / The leaves of Maytenus ilicifolia are widely used within the traditional Brazilian medicine due to its properties against gastric disorders. Once proved its efficacy and safety, this vegetable drug has been the object of several studies to establish the basis for quality control. Taking this into consideration, it was necessary to evaluate the feasibility of developing an analytical method based on the precipitation of tannins, by using polyvinylpyrrolidone for precipitation. The data have shown that the removal of the tannins in solution was successful when insoluble polyvinylpyrrolidone was used. Hereby it was observed that the polymer has also the ability to precipitate other polyphenols besides the tannins from the aqueous solution of M. ilicifolia. However, the interactions of the polymer happened mostly with the condensed tannins. Further it was developed and also validated an HPLC method to separate and quantify catechin and epicatechin present in aqueous extracts of M. ilicifolia. No significant variations of peak areas or retention times were observed when the evaluation of the method was executed, showing satisfactory chromatographic conditions. In order to make a spray dried extract (SDE) using a spray-drier fitted out with a rotary atomizer, it was necessary to concentrate the extractive solution. This operation had been performed under reduced pressure until a content of 15 % solids was achieved. The drying of the concentrated solution lead to a yield of 90 %, and the obtained SDE presented spherical particles, which have a rough surface and a mean particle size of 22,51.1.m. The technological characterization of the SDE showed that attributes such as densities (tap and bulk), compressibility and flow, have been improved when compared to the product prepared using a mini spray-drier supplied with a pneumatic nozzle. However, these modifications were not enough to enable its direct compression. Therefore, the material was compacted to produce granules after slugging or roller compaction, The compressional analysis of the SDE and each granule batch using the Heckel equation proved that the increase in the compaction force once processing the granulation was the main factor to reduce the material's ability to undergo plastic deformation. Consequently, the recompression of the granules in a tablet press led to compacts with a lower crushing strength compared to that prepared by direct compression of the pharmaceutical complex. Whereas the SDE has shown a reduced tendency to particle rearrangement at early stage of compression, the granules showed an intense fragmentation and rebound behavior, presenting a plastic behavior when higher compaction pressures were used. Finally, tablets containing a high dose of granulated spray dried extract of M. ilicifolia were prepared by using the following excipients: microcrystalline cellulose (filler/binder), colloidal silicon dioxide (glidant and moisture adsorber) and cross-linked carboxymethylcellulose (disintegrant). The influences of colloidal silicon dioxide (CSD) and cross-linked carboxymethylcellulose (CMC-Na) on the tablet hardness, disintegration time and friability were evaluated by a central composite design. The data were analyzed statistically and mathematical models were used to create response surfaces. The results have indicated that the concentration of CSD shows an inverse relation to the responses of hardness and friability, while the concentration of CMC-Na was the most important factor that caused a reduction of the time necessary for total disintegration. The optimal conditions for processing were chosen by the overlapping of graphics, taking into consideration that the formulation should present a minimum of disintegration time, lower friability and a maximum of hardness. Thus, it was found that the best formulation should have a content of 1.2% (w/w) of CSD and 5.0% (w/w) of CMC-Na. Regarding these conditions, the tablets have shown a hardness of 107.9 N, friability of 0.56% (w/w) and a disintegration time of 6.8 min.