Environmental awareness and uncertainty about continued supply of fossil fuel has given rise to the renewable energy movement. Wind based power generation has been at the forefront of the motion to integrate distributed energy sources in the traditional power system. Due to various technical restrictions, wide scale penetration of wind generated power has been held back by most utilities. One such restriction is the variability of generation due to the technology’s dependence on Mother Nature. Energy storage devices can complement the wind generators by reducing this variability. These devices can store excess generation for supply during low generation periods. There are several promising technologies for both energy storage and power storage applications. Power storage devices provide short term fluctuation dampening capability while energy storage devices allow longer term storage. Pumped hydro, Vanadium Redox battery and Sodium-Sulphur battery are some of the viable energy storage technologies. This project provides a set of algorithms and guidelines to obtain the optimal configuration parameters of an energy storage device. To verify the efficiency of the algorithms, a model system has been obtained from a local utility. This system represents a typical radial distribution system in rural Ontario. The load demand, wind speed and energy prices for a period of one year have been obtained from utilities and Environment Canada. The main goal in determining the location of the storage device within a distribution system is to minimize the total cost of energy and the total energy loss during the period of analysis. Locating the storage device near the wind turbines or near the largest loads lead to the optimum results. Buses that are located near those elements can be considered as suitable locations for the storage device. The energy storage capacity and charge-discharge rate of the storage device are selected based on four criteria: maximize wind turbines’ load following capability, maximize capacity factors of the wind turbines, minimize system energy losses and minimize system energy costs. A weight based multi-objective optimization algorithm has been proposed to assign various priorities to these criteria and obtain a single solution. The larger the energy storage capacity of the storage device, the better the improvement in system performance. Lower charge-discharge ramp rates provide superior results. The parameters for storage device operating schedule, i.e. charge-discharge trigger levels, have been selected using similar criteria and weighted objective approach as for the capacity selection process. Higher charge trigger levels and moderate discharge trigger levels provide the optimum system performance. Once a set of parameters for the storage device has been selected, bus voltages over the period of study are analyzed. Voltage variations outside certain limits have been identified. Finally, a Monte Carlo based simulation approach is presented to obtain output parameter (system performance) variation ranges for pseudo random changes in input parameters.

Since most of the energy input is converted to thermal energy in laser applications, the proper thermal management of laser systems is an important issue. Maintaining the laser diode and crystal temperature distributions in a narrow range during the operation is the most crucial requirement for the cooling of a laser system. In the present study, thermoelectric cooling (TEC) of a 1064 nm wavelength diode pumped laser source is investigated both experimentally and numerically. During the heat removal process, the thermal resistance through and between the materials, the proper integration of the TEC assembly, and the heat sink efficiency become important. For the aim of evaluating and further improving the system performance, various assembly configurations, highly conductive components, efficient interface materials and heat sink alternatives are considered. Several experiments are conducted during the system development stage, and parallel numerical simulations are performed both for comparison and also for providing valuable input for the system design. Results of the experiments and the simulations agree well with each other. As the laser device works in the transient regime, the experiments and the simulations are also implemented in this regime. In the final part of the study, the experiments are performed under the actual device working conditions. It is proved that with the designed TEC module and the copper heat sink system, the laser device can operate longer than the required operational time successfully.

Made available in DSpace on 2014-10-09T12:55:30Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:05:04Z (GMT). No. of bitstreams: 0 / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Submitted by Claudinei Pracidelli (cpracide@ipen.br) on 2015-07-23T10:59:51Z No. of bitstreams: 0 / Made available in DSpace on 2015-07-23T10:59:51Z (GMT). No. of bitstreams: 0 / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Made available in DSpace on 2014-12-17T15:03:21Z (GMT). No. of bitstreams: 1 AraceliNFAR.pdf: 2301024 bytes, checksum: 03fe9d44dc204d4f200f14f66d76dcb0 (MD5) Previous issue date: 2009-04-30 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / In Natal still dominates the use of individual disposal systems for domestic sewage, once only 29% of the city has a sewarage system. Wastes that are accumulated in these individual treatment systems should be exhausted periodically, service provided by collector entrepreneurs. Some of these companies causing major damage to the environment. In Natal, only two companies have their own septage (RESTI) treatment system, which were designed with parameters from domestic sewage generating strain and inefficient systems. Therefore, the characterization becomes essential as a source of parameters for their design. Thus, this work presents the physical-chemical and microbiological characterization of waste pumped from individual sewage treatment systems. Samples collections were made weekly from 5 different trucks at the reception point on the treatment plant on the point of the preliminary treatment. From each truck it was taken 5 samples during the discharge in order to make a composite sample. Afterwards, samples were carried out to laboratory and analyses for determination of temperature, pH, conductivity, BOD, COD, nitrogen (ammonia e organic), alkalinity, oils, phosphorus, solids, faecal coliforms and helminth egg. The results were treated as a single database, and ranked according to its generating source (multi and single house, lodging, health, services and / or food), area of origin (metropolitan, south and north) and type of system (cesspits, septic tank and / or sink). Through these data it was possible to verify that the type of system adopted by most in Natal and the metropolitan region is cesspit, besides to confirm the difference between the septage of areas with a population have different social and economical characteristics. It was found that the septage have higher concentrations than domestic sewage, except for thermotolerant coliforms that showed concentrations of 1,38E+07. Among the parameters studied, is the median values identified for COD (3,549 mg / L), BOD (973mg / L) and total solids (3.557mg / L). The volatile fraction constitutes about 70% of the total solids of the septage. For helminths has been a median of 7 eggs/L. In general, the characteristics of the waste followed the variability found in the literature reviewed for all variables, showing high amplitudes / Na cidade de Natal ainda predomina o uso de sistemas de disposi??o individual de esgotos dom?sticos, tendo em vista que apenas 29% da cidade possui rede coletora de esgotos. Os res?duos que ficam acumulados dentro destes sistemas individuais de tratamento devem ser esgotados periodicamente, servi?o prestado pelas empresas imunizadoras. Algumas destas empresas despejam estes res?duos em corpos aqu?ticos, trazendo grandes preju?zos para o meio ambiente. Na cidade de Natal, apenas duas empresas possuem sistema pr?prio de tratamento dos Res?duos Esgotados de Sistemas de Tratamento Individual (RESTI) de esgoto. O dimensionamento destes sistemas de tratamento com dados de esgotos dom?sticos tr?s como conseq??ncia sistemas sobrecarregados e ineficientes. Portanto, a caracteriza??o se torna imprescind?vel como fonte de par?metros para o dimensionamento das esta??es de tratamento do RESTI. Desta forma, este trabalho apresenta a caracteriza??o do RESTI quanto as suas caracter?sticas f?sico-qu?micas e microbiol?gicas para que existam par?metros confi?veis de dimensionamento. Os carros limpa-fossas realizam o esgotamento destes sistemas, despejando-os posteriormente em um sistema de tratamento (lagoas de estabiliza??o em s?rie da empresa respons?vel). As coletas foram realizadas semanalmente de cinco caminh?es diferentes no ponto de descarga dos carros limpa-fossa na entrada do tratamento preliminar do sistema de tratamento. De cada caminh?o foram tomadas cinco amostras ao longo da descarga para formar uma amostra composta do caminh?o. Em seguida, as amostram foram levadas ao laborat?rio para realizar as an?lises de temperatura, pH, condutividade, DBO, DQO, Nitrog?nio (org?nico e amoniacal), alcalinidade, ?leos e graxas, f?sforo, s?lidos, coliformes termotolerantes e helmintos. Os dados foram tratados como um banco de dados ?nico, sendo posteriormente classificados de acordo com sua fonte geradora (multifamiliar, unifamiliar, hospedagem, sa?de, servi?os e/ou alimenta??o), zona de origem (metropolitana, sul e norte) e tipo de sistema esgotado (fossa, tanque s?ptico e/ou sumidouro). Atrav?s destes dados foi poss?vel verificar que o tipo de sistema mais adotado pelo munic?pio de Natal e sua regi?o metropolitana s?o as fossas, al?m de comprovar a diferen?a entre os res?duos esgotados de regi?es que apresentam caracter?sticas s?cio-econ?micas diferentes. Verificou-se que estes res?duos apresentam concentra??es bem mais elevadas que as de esgoto dom?stico, com exce??o do par?metro de coliformes termotolerantes que apresentou concentra??o de 1,38E+07. Dentre os par?metros estudados, destaca-se os valores medianos identificados para DQO (3.549 mg/L), DBO (973mg/L) e ST (3.557mg/L). A fra??o vol?til representa cerca de 70% dos s?lidos totais deste tipo de res?duo. A concentra??o de ovos de helmintos apresentou uma mediana de 7 ovos/L. De forma geral, as caracter?sticas dos res?duos acompanharam a variabilidade encontrada na literatura revisada para todas as vari?veis analisadas, apresentando elevadas amplitudes

Made available in DSpace on 2014-10-09T12:55:30Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:05:04Z (GMT). No. of bitstreams: 0 / Neste trabalho, foi desenvolvido um sistema laser utilizando como meio ativo um cristal de YLF cortado em ângulo de Brewster e dopado com 15mol% de érbio substituindo o ítrio, emitindo na região dos 3 m e bombeado por diodo laser com pico de emissão em 975 nm. Com este sistema foi obtido 1,80(18) W operando em regime quasecontínuo. O oscilador foi otimizado para aplicações médicas operando com potência máxima em 250 s de tempo de pulso. O peculiar comportamento temporal do laser foi estudado neste trabalho pela primeira vez, assim como a otimização da potência máxima em função da duração do pulso. Há diferenças nos mecanismos intrínsicos do laser quando este é operado em regime contínuo ou pulsado, especialmente no efeito da transferência de energia por conversão ascendente W22, cujo valor ainda é muito divergente na literatura. O valor estimado neste trabalho para este parâmetro de transferência de energia é 2,0x10-16 cm3/s. / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Submitted by Claudinei Pracidelli (cpracide@ipen.br) on 2015-07-23T10:59:51Z No. of bitstreams: 0 / Made available in DSpace on 2015-07-23T10:59:51Z (GMT). No. of bitstreams: 0 / Lasers Raman são dispositivos que proporcionam uma maneira prática de transformar comprimentos de onda fundamentais em novas linhas espectrais via Espalhamento Raman Estimulado (Stimulated Raman Scattering - SRS). Quando combinados com outros processos de conversão não lineares, os lasers Raman fornecem acesso a comprimentos de onda na região do visível no espectro eletromagnético, que de outra maneira seriam de difícil acesso, como o laranja-amarelo, verde-limão e diversas linhas no azul. A grande vantagem dos lasers Raman é a possibilidade de geração de múltiplas frequências a partir de uma mesma combinação de cristais, tornando esse tipo de laser dispositivos baratos e compactos quando comparados a tecnologias como OPO. Neste trabalho um cristal de Nd:YVO4 foi bombeado por diodo, em configuração transversal, sendo o cristal o responsável pela emissão laser e pelo espalhamento Raman. Na primeira parte do trabalho, a cavidade utilizada apresentava alto fator de qualidade para o comprimento de onda fundamental (1064 nm) e foi estudada a operação laser do 1º Stokes (1176 nm) em regimes de operação quase contínua (q-cw) e contínua (cw). Foi explorada a configuração com uma dobra do feixe laser em ângulo rasante na superfície de bombeamento, bem como a configuração com duas dobras nesta mesma superfície (double beam mode controlling - DBMC). Na segunda parte do trabalho, um cristal LBO foi utilizado para a geração do segundo harmônico (SHG) em 588 nm, o que corresponde a um laser laranja-amarelo. Foi utilizada a configuração com uma dobra e operação cw,com a qual a cavidade apresentava alto fator de qualidade tanto para o 1064 nm quanto 1176 nm. Com a configuração de uma dobra, foi demonstrado que o laser Raman opera em multimodo, com uma variedade de modos de Hermite-Gauss que puderam ser selecionados através apenas do alinhamento da cavidade, incluindo o modo TEM00. Com configuração DBMC, o laser apresentou operação estável oscilando o modo TEM00. Em 1176 nm em regime q-cw, foi obtida a potência máxima de 8,2 W por pulso (multimodo) e 11,7% de eficiência óptica de conversão (diodo para o 1º Stokes), e operando em modo TEM00 a potência máxima de 3,7 W por pulso e eficiência de 5,4% foi obtida com a configuração de duas dobras, de maneira que a tecnologia DBMC se mostrou eficiente para geração de um laser robusto e estável operando com o modo TEM00. Em regime cw o melhor resultado em termos de potência e eficiência foi obtido com a configuração de uma dobra, correspondendo a 1,8 W e 7,3% de eficiência com o laser operando em multimodo. Com o laser laranja, foi demonstrada a operação do modo TEM00 para potências de bombeamento abaixo de 14,5 W. A potência máxima obtida em multimodo foi 820 mW correspondendo a 4% de eficiência óptica de conversão. / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

We use spectroscopy to study infrared optoelectronic inter and intraband semiconductor carrier dynamics. The overall aim of this thesis was to study both III-V and Pb chalcogenide material systems in order to show their future potential use in infrared emitters. The effects of bandstructure engineering have been studied in the output characteristics of mid-IR III-V laser diodes to show which processes (defects, radiative, Auger and phonon) dominate and whether non-radiative processes can be suppressed. A new three-beam pump probe experiment was used to investigate interband recombination directly in passive materials. Experiments on PbSe and theory for non-parabolic near-mirror bands and non-degenerate statistics were in good agreement. Comparisons with HgCdTe showed a reduction in the Auger coefficient of 1-2 orders of magnitude in the PbSe. Using Landau confinement to model spatial confinement in quantum dots (QDs) "phonon bottlenecking" was studied. The results obtained from pump probe and cyclotron resonance saturation measurements showed a clear suppression in the cooling of carriers when Landau level separation was not resonant with LO phonon energy. When a bulk laser diode was placed in a magnetic field to produce a quasi quantum wire device the resulting enhanced differential gain and reduced Auger recombination lowered Ith by 30%. This result showed many peaks in the light output which occurred when the LO phonon energy was a multiple of the Landau level separation. This showed for the first time evidence of the phonon bottleneck in a working laser device. A new technique called time resolved optically detected cyclotron resonance, was used as a precursor to finding the earner dynamics within a spatially confined quantum dot. By moving to the case of a spatial QD using an optically detected intraband resonance it was possible to measure the energy separation interband levels and conduction and valence sublevels within the dot simultaneously. Furthermore this technique has been shown that the inhomogeneous broadening of the photoluminescence spectrum is not purely affected by just size and composition. We suggest that other processes such as state occupancy, In roughing, and exciton binding energies may account for the extra energy.

This thesis is based on the series of scholarly article dedicated to the issue of pumping in the differential scanning chamber of an environmental scanning microscope. The thesis is based on Danilatos’s study where the pumping of the differential pumped chamber is solved by means of the Monte Carlo statistical method. The thesis analyzes gas flow in the experimental chamber using the Pipot tube. The analyses will be used for the design of the experimental chamber which will serve for the experimental evaluation of the flow results in the chamber using the continuum mechanics.

The thesis is focused on the medium dynamics simulation in the environmental scanning electron microscope. Specifically, it researches (examines) the conical aperture location effect in the differential pumped chamber and the width of the pumping channel in this chamber. The theoretical part deals with the environmental scanning microscope generally and other tools used in this thesis, e.g. ANSYS Fluen software, fluid turbulence, medium free path of molecules and electrons scattering. In the practical part, the work is focused on data processing from the ANSYS Fluent program and on their evaluation.