International Telemetering Conference Proceedings / October 27-30, 1997 / Riviera Hotel and Convention Center, Las Vegas, Nevada / An edge-based hybrid finite element boundary integral (FE-BI) method using cylindrical shell elements is described for analyzing conformal quarter-wave patches embedded in a circular cylinder. Special care is also taken to deal with weight functions, dyadic Green’s function, and feed model. Some types of the patch arrays embedded in different circular radius have been developed. The tests of their VSWRs and radiation characteristics are in good agreement with the theoretical results.

In this thesis, a highly selective broadband hybrid bandpass filter operating between 0.4-2.0 GHz with a stopband up to 7 GHz is designed and analyzed. The realization is carried out by hybrid method, which combines both lumped and distributed element filters. In this approach, two separate filters, which are lumped highpass with 0.4 GHz corner frequency and distributed stripline lowpass with 2 GHz corner frequency, are combined to get the bandpass filter that has a passband in between 0.4 to 2.0 GHz. The usage of the lumped elements for the highpass filter resulted in a great size reduction compared to distributed element approach. The design software FILPRO&trade / is used to synthesize the trial filters. More than forty filters are synthesized, and among them, the ones that have better properties are chosen for further processes. Optimization, modeling and electromagnetic simulations of the selected lumped and distributed filters are carried out on the software GENESYS&trade / . Distributed filters are also simulated using the software SONNET&trade / . After the simulations, all of the simulated filters are realized and measured, and the level of consistency with the simulations is observed. According to the results of the measurements, the filter combination that has the best combination of low insertion loss, small dimensions, high stopband attenuation and low spur levels is selected for the final bandpass filter structure and a few variants are examined to get the final structure.

The thesis represents the design for dual-band quarter wavelength and half wavelength microstrip transmission line. Chapter 2 proposed the design of a novel dual-band asymmetric pi-shaped short-circuited quarter wavelength microstrip transmission line working at frequencies 1GHz and 1.55 GHz for 50Ω transmission line and at frequencies 1GHz and 1.43GHz for 60Ω transmission line. Chapter 3 proposed the design of a novel dual-band quarter wavelength microstrip transmission line with asymmetrically allocated open stubs and short-circuited stubs working at frequencies 1GHz and 1.32GHz. Chapter 4 proposed the design of dual-band pi-shaped open stub half wavelength microstrip transmission line working at frequencies 1GHz and 2.07GHz. Numerical simulations are performed both in HyperLynx 3D EM and in circuit simulator ADS for all of the proposed designs to measure the return loss (S11) and insertion loss (S12) in dB and phase response for S12 in degree.

High efficiency is an essential requirement for any system, where the energy can be saved with full retention of system performance. The power amplifier in modern mobile communications system consumes most of the supplied power through the dissipated power and the required cooling systems. However, as new services were added as features for the developed mobile generations, the required data rate has increased to fulfil the new requirements. In this case, the data should be sent with the allocated bandwidth, so complex modulation schemes are used to utilise the available bandwidth efficiently. Nevertheless, the modulated signal will have a Peak to Average Power Ratio (PAPR) which increases as the modulation complexity is increasing. In this case, the power amplifier should be backed off and designed to provide good linearity and efficiency over high PAPR. Among the efficiency enhancement techniques, the Doherty technique (Load modulation technique) is the simplest one, where no additional circuity nor signal processing is required. In this work, the theory of load modulation amplifiers is investigated through two asymmetrical Doherty Power Amplifiers (DPA) targeting 3.3-3.5 GHz were designed and fabricated using two transistors (25 W and 45 W). In addition, more compact load modulation amplifiers targeting sub 6-GHz bandwidth of 5G specifically 3.4-3.8 GHz is discussed including the theory of implementing these amplifiers, where different amplifier capabilities are explored. Each amplifier design was discussed in detail, in which the input and output matching networks were designed and tested in addition to the design of the stability circuit to make sure that the amplifier is stable and working according to the specified requirements. The fabricated circuits were evaluated practically using the available instrument test, whereas Microwave Office software was used for the simulation purpose, each amplifier was designed separately, where all the designed amplifiers were able to provide the targeted efficiency at different back-off power points. Besides, some additional factors that affect the designed load modulation amplifiers such as the effect of the harmonics at the back-off and mismatching the amplifier is discussed. / European Union’s Horizon 2020 research and innovation programme (SECRET)

No / To mitigate potential interferences with coexisting wireless systems operating over 3.3-3.6 GHz, 5.15-5.35 GHz, or 5.725-5.825 GHz bands, four novel band-notched antennas suitable for ultra-wideband (UWB) applications are proposed. These include UWB antennas with a single wide notched band, a single narrow notched band, dual notched bands, and triple notched bands. Each antenna comprises a half-circle shaped patch with an open rectangular slot and a half-circle shaped ground plane. Good band-notched performance is achieved by using high permittivity and low dielectric loss substrate, and inserting quarter-wavelength horizontal/vertical stubs or alternatively embedding quarter-wavelength open-ended slots within the feed line. The results of both simulation and measurement confirm that the gain suppression of the single and multiple band-notched antennas in each desired notched band are over 15 dB and 10 dB, respectively. The radiation pattern of the proposed triple band-notched design is relatively stable across the operating frequency band.

Power dividers are vital components and widely used in radio technology, such as antenna arrays, power amplifiers, multiplexers and mixers. A good example is the well-known Wilkinson power divider with its distinctive feeding network characteristics. A comprehensive review indicated that limited research is carried out in the area of planar multiport and reconfigurable power dividers in terms of the power levels between output ports. The main objectives of this work were to develop a small size power divider, a planer multi-output ports power divider and a power divider with a reconfigurable power division ratio. These power dividers were designed to operate over either an ultra-wideband frequency (3.1-10.6 GHz) or WLAN bands (2.4 or 5.2 GHz). A novel multi-layered topology solved the complexity of interconnecting isolation resistors by introducing an additional layer below the ground layer. The prototype was fabricated and tested to validate the results. The measurements and simulation were in good agreement. Finally, a novel uniplanar power divider with reconfigurable output power level difference was developed. The configurability feature was achieved by tuning the quarter wave transformer using one varactor diode. The power divider was applied to improve a full duplex system cancellation performance at the receiver element caused by interference from in-site transmitting antennas. This study investigated fixed power dividers, multi-output power dividers and reconfigurable power dividers. The measurements validated by the simulation results and applications proved the designed power dividers could be used in practical applications. / Higher Committee for Education Development (HCED), Iraq