yes / This paper describes the characterization and design of energy efficient user terminal transceiver power amplifier. To reduce the design of bulky external circuitry, the load modulation technique is employed. The design core is based on the combination of Class B and Class C that includes quarter wavelength transformer at the output to perform the load modulation. The handset transceiver for this power amplifier is designed to operate over the frequency range of 3.4GHz to 3.6GHz mobile WiMAX band. The performances of the load modulation amplifier are compared with conventional Class B amplifier. The results of 30dBm output power and 53% power added efficiency are achieved.

Yes / The biggest challenge for future 4G systems is the need to limit the energy consumptions of battery-powered and base station devices, with the aim to prolong their operational time and avoid active cooling in the base station. The green wireless communications requires research in areas such as energy efficient RF front end, MAC protocol, networking, deployment, operation, and also the integration of base station with renewable power supply. In this paper, the design concept of energy efficient RF front end is considered in terms of RF power amplifiers at which it represents the workhorse of modern wireless communication systems and inherently nonlinear. The approach of output power back off is to amplify the signal at the linear region to avoid distortion, but this approach suffers from significant reduction in efficiency and power output. To boost the efficiency at wide range of output power and keep the same margin for signal with high crest factor, the load modulation technique with new offset line are employed to operate over the frequency range of 3.4GHz to 3.6GHz band. The performances of load modulation power amplifier are compared with balanced amplifier. The results of 42dBm output power and 62% power added efficiency are achieved.

Linearity and efficiency are both critical parameters for radio frequency transmitter applications. In theory, a Doherty amplifier is a linear amplifier that is significantly more efficient than comparable conventional linear amplifiers. It comprises two amplifiers, connected at their outputs by a quarter-wave transformer. The main amplifier is always on, while the peaking amplifier is off during low power levels. Load modulation of the main amplifier occurs when the peaking amplifier is on due to the quarter-wave transformer, ensuring the main amplifier never enters saturation. This results in an efficiency characteristic that increases with respect to input power at twice the normal rate at low power levels, and plateaus to a high value at high power levels. However, in much of the research that has been done to-date, less-than-ideal results have been achieved (although efficiency was better than a conventional amplifier). It was decided to investigate the cause of the discrepancy between theoretical and practical results, and devise a method to counteract the problem. It was discovered that the main cause of the discrepancy was non-ideal transistor gate-voltage to drain-current characteristics. The implementation of a gate bias control scheme based upon measured transistor transfer characteristics, and the desired main and peaking amplifier output currents, resulted in a robust method to ensure near-ideal results. A prototype amplifier was constructed to test the control scheme, and theoretical, simulated and measured results were well matched. The amplifier had a region of high efficiency in the high power levels (over 34% for the last 6 dB of input power), and the gain was nearly constant with respect to input power (between 4 and 5 dB over the dynamic range). Furthermore, it was decided to investigate the role harmonics play within the Doherty amplifier. A classical implementation shunts unwanted harmonics to ground within the main and peaking amplifiers. However, odd harmonics generated by the peaking amplifier can be used to operate the main amplifier like a class F amplifier. This means its supply voltage can be lowered, without the amplifier entering saturation, and the efficiency of the Doherty amplifier can be increased without a detrimental effect on the its linearity. A prototype amplifier was constructed to test this theory, and gave good results, with better efficiency than that of a conventional amplifier, and a constant gain with respect to input power (between 6.4 dB and 6.5 dB over the dynamic range).

High efficiency is an essential requirement for any system, where the energy can be saved with full retention of system performance. The power amplifier in modern mobile communications system consumes most of the supplied power through the dissipated power and the required cooling systems. However, as new services were added as features for the developed mobile generations, the required data rate has increased to fulfil the new requirements. In this case, the data should be sent with the allocated bandwidth, so complex modulation schemes are used to utilise the available bandwidth efficiently. Nevertheless, the modulated signal will have a Peak to Average Power Ratio (PAPR) which increases as the modulation complexity is increasing. In this case, the power amplifier should be backed off and designed to provide good linearity and efficiency over high PAPR. Among the efficiency enhancement techniques, the Doherty technique (Load modulation technique) is the simplest one, where no additional circuity nor signal processing is required. In this work, the theory of load modulation amplifiers is investigated through two asymmetrical Doherty Power Amplifiers (DPA) targeting 3.3-3.5 GHz were designed and fabricated using two transistors (25 W and 45 W). In addition, more compact load modulation amplifiers targeting sub 6-GHz bandwidth of 5G specifically 3.4-3.8 GHz is discussed including the theory of implementing these amplifiers, where different amplifier capabilities are explored. Each amplifier design was discussed in detail, in which the input and output matching networks were designed and tested in addition to the design of the stability circuit to make sure that the amplifier is stable and working according to the specified requirements. The fabricated circuits were evaluated practically using the available instrument test, whereas Microwave Office software was used for the simulation purpose, each amplifier was designed separately, where all the designed amplifiers were able to provide the targeted efficiency at different back-off power points. Besides, some additional factors that affect the designed load modulation amplifiers such as the effect of the harmonics at the back-off and mismatching the amplifier is discussed. / European Union’s Horizon 2020 research and innovation programme (SECRET)

No description available.

<p>The purpose of this master thesis was to study if the drain efficiency of power amplifiers can be maintained at power back off using a technique called load modulation.</p><p>The amplifier classes studied are E, F and D-1. The target figure was to obtain a 10 to 12 dB dynamic range of amplitude with reasonable efficiency. Studies of power amplifiers have been made to understand how power is generated. Several different load modulation networks have been evaluated. Attempts to derive design equations for the modulation networks have also been done.</p><p>The thesis work was carried out with simulations in ADS 2006. As active devices commercially available bare-die transistor models have been used. The power rating of the dies are 15 W.</p><p>A dynamic range of amplitude of over 15 dB has been achieved with drain efficiency greater than 60 percent. The peak output power is in the 40 – 45 dBm range.</p>

The purpose of this master thesis was to study if the drain efficiency of power amplifiers can be maintained at power back off using a technique called load modulation. The amplifier classes studied are E, F and D-1. The target figure was to obtain a 10 to 12 dB dynamic range of amplitude with reasonable efficiency. Studies of power amplifiers have been made to understand how power is generated. Several different load modulation networks have been evaluated. Attempts to derive design equations for the modulation networks have also been done. The thesis work was carried out with simulations in ADS 2006. As active devices commercially available bare-die transistor models have been used. The power rating of the dies are 15 W. A dynamic range of amplitude of over 15 dB has been achieved with drain efficiency greater than 60 percent. The peak output power is in the 40 – 45 dBm range.

Les fortes capacités actuelles et envisagées des futurs liens satellites de communication pour la 5G conduisent les signaux traités dans les charges utiles à présenter simultanément d'importantes variations d'amplitude (PAPR>10dB) et de très larges bandes passantes instantanées (BW>1GHz). A l'intérieur du sous-système d'émission hyperfréquence, le fonctionnement du module d'amplification de puissance se trouve très contraint par les formes d'ondes véhiculées, il se présente comme l'un des postes de consommation énergétique des plus importants, et ayant le plus d'impact sur l'intégrité du signal émis. Dans ce contexte, les fonctions dédiées au traitement numérique des signaux et couramment implémentées par le processeur numérique (telles que le filtrage, la canalisation, et éventuellement la démodulation et la régénération des signaux bande de base) embarquées dans les charges utiles, représentent une solution à fort potentiel qui permettrait de relâcher les contraintes reportées sur la fonction d'amplification de puissance afin de gérer au mieux la ressource électrique allouée. Ces travaux de thèse proposent d'étudier les potentialités d'amélioration du fonctionnement en rendement et linéarité d'un amplificateur de type Doherty à double entrée de gamme 20W en technologie GaN et fonctionnant en bande C. La combinaison des signaux de puissance sur la charge RF est optimisée par une distribution optimale des signaux en amplitude et phase à l'entrée par des moyens numériques de génération. Dans un premier temps une méthodologie de conception large bande d'un amplificateur Doherty est introduite et validée par la conception d'un démonstrateur en bande C. Dans un second temps, l'outil expérimental permettant l'extraction des lois optimales de distribution d'amplitude et de phase RF est présenté en détail, et la caractérisation expérimentale du dispositif en double entrée est réalisée puis comparée aux simulations. Finalement, en perspective à ces travaux, une étude préliminaire des potentialités de l'architecture Doherty à double entrée pour la gestion d’une désadaptation de la charge de sortie (gestion de TOS) est menée et des résultats sont mis en avant. / The high capabilities of current and future 5G communication satellite links lead the processed signals in the payloads to simultaneously exhibit large amplitude variations (PAPR>10dB) and wide instantaneous bandwidths (BW>1GHz). Within the microwave transmission subsystem, the operation of the power amplification stage is highly constrained by the transmitted waveforms, it is one of the most energy-consuming module of the payload affecting as well the integrity of the transmitted signal. In this context, the functions dedicated to digital signal processing and currently implemented by the digital processor (such as filtering, channeling, and possibly the demodulation and regeneration of baseband signals) embedded in the payloads, represent a potential solution that would reduce the constraints reported on the power amplification function and help to manage the allocated power ressource. This work proposes a study on the capability of dual input power amplifier architectures in order to manage the efficiency-linearity trade-off over a wide bandwidth. This study is carried out on a 20W GaN Doherty demonstrator operating in C band. The combination of the output signals on the RF load is managed by an optimal amplitude and phase distribution that is digitally controlled at the input. Firstly, a wideband design methodology of Doherty amplifier is introduced and validated on a C band demonstrator. In a second time the experimental tool allowing the extraction of amplitude and phase input distributions is presented, the dual input characterization is achieved and compared with simulation results. Finally, in perspective of this work, a preliminary study of the capabilities of the digital Doherty for the management of an output load mismatch (VSWR management) is carried out and the results are put forward.