Fundamental understanding of high strain rate deformation behavior of materials is critical in designing new alloys for wide-ranging applications including military, automobile, spacecraft, and industrial applications. High entropy alloys, consisting of multiple elements in (near) equimolar proportions, represent a new paradigm in structural alloy design providing ample opportunity for achieving excellent performance in high strain rate applications by proper selection of constituent elements and/or thermomechanical processing. This dissertation is focused on fundamental understanding of high strain-rate deformation behavior of several high entropy alloy systems with widely varying microstructures. Ballistic impact testing of face centered cubic Al0.1CoCrFeNi high entropy alloy showed failure by ductile hole growth. The deformed microstructure showed extensive micro-banding and micro-twinning at low velocities while adiabatic shear bands and dynamic recrystallization were seen at higher velocities. The Al0.7CoCrFeNi and AlCoCrFeNi2.1 eutectic high entropy alloys, with BCC and FCC phases in lamellar morphology, showed failure by discing. A network of cracks coupled with small and inhomogeneous plastic deformation led to the brittle mode of failure in these eutectic alloys. Phase-specific mechanical behavior using small-scale techniques revealed higher strength and strain rate sensitivity for the B2 phase compared to the L12 phase. The interphase boundary demonstrated good stability without any cracks at high compressive strain rates. The Al0.3CoCrFeNi high entropy alloy with bimodal microstructure demonstrated an excellent combination of strength and ductility. Ballistic impact testing of Al0.3CoCrFeNi alloy showed failure by ductile hole growth and demonstrated superior performance compared to all the other high entropy alloy systems studied. The failure mechanism was dominated by micro-banding, micro-twining, and adiabatic shear localization. Comparison of all the high entropy alloy systems with currently used state-of-the-art rolled homogenous armor (RHA) steel showed a strong dependence of failure modes on microstructural features.

Gegenwärtige Bestrebungen materialwissenschaftlicher Forschung beschäftigen sich unter anderem mit der Überführung zweidimensionaler Elemente elektronischer, optischer, plasmonischer oder magnetischer Funktionalität in den dreidimensionalen (3D) Raum. Dieser Ansatz vermag mittels Krümmung und struktureller Topologie bereits vorhandene Eigenschaften abzuändern beziehungsweise neue Funktionalitäten bereitzustellen. Vor allem Vektoreigenschaften wie die Magnetisierung kondensierter Materie lassen sich aufgrund der Brechung der Inversionssymmetrie in gekrümmten Flächen stark beeinflussen. Neben der Entwicklung diverser Vorgänge zur Herstellung 3D magnetischer Gegenstände sind geeignete Untersuchungsmethoden wie beispielsweise tomografische Abbildungen der Magnetisierung von Nöten, die maßgeblich die physikalischen Eigenschaften bestimmen. Die vorliegende Dissertationsschrift befasst sich mit der Abbildung von magnetischen Domänen in 3D gekrümmten Dünnschichten beruhend auf dem Effekt des zirkularen magnetischen Röntgendichroismus (XMCD). Die in diesem Zusammenhang entwickelte magnetische Röntgentomografie (MXT) basierend auf weicher Röntgenmikroskopie stellt eine zu Elektronenholografie und Neutronentomografie komplementäre Methodik dar, welche großes Anwendungspotential in der elementspezifischen Untersuchung magnetischer gekrümmter Flächen mit örtlicher Auflösung im Nanometerbereich aufweist. Die Schwierigkeit der Interpretation von Abbildungen magnetischer Strukturen in gekrümmten Flächen rührt von der Dreidimensionalität und der Vektoreigenschaft der Magnetisierung her. Die hierzu notwendigen Kenntnisse sind anhand von zwei topologisch verschiedenen Flächen in Form hemisphärischer Kappen und hohler Zylinder erschlossen worden. Die praktische Anwendung von MXT ist abschließend anhand der Rekonstruktion magnetischer Domänen in aufgerollten Dünnschichten mit zylindrischer Form verdeutlicht. / One of the foci of modern materials sciences is set on expanding conventional two-dimensional electronic, photonic, plasmonic and magnetic devices into the third dimension. This approach provides means to modify conventional or to launch novel functionalities by tailoring curvature and three-dimensional (3D) shape. The degree of effect is particularly high for vector properties like the magnetization due to an emergent inversion symmetry breaking. Aside from capabilities to design and synthesize 3D magnetic architectures, proper characterization methods, such as magnetic tomographic imaging techniques, need to be developed to obtain a thorough understanding of the system’s response under external stimuli. The main objective of this thesis is to develop a visualization technique that provides nanometer spatial resolution to image the peculiarities of the magnetic domain patterns on extended 3D curved surfaces. The proposed and realized concept of magnetic soft X-ray tomography (MXT), based on the X-ray magnetic circular dichroism (XMCD) effect with soft X-ray microscopies, has the potential to become a powerful tool to investigate element specifically an entirely new class of 3D magnetic objects with virtually any shape and magnetization. Imaging curved surfaces meets the challenge of three-dimensionality and requires a profound understanding of the recorded XMCD contrast. These experiences are gained by visualizing magnetic domain patterns on two distinct 3D curved surfaces, namely magnetic cap structures and rolled-up magnetic nanomembranes with cylindrical shape. The capability of MXT is demonstrated by reconstructing the magnetic domain patterns on 3D curved surfaces resembling hollow cylindrical objects.

Lithium ion batteries (LIBs) have attracted considerable interest due to their wide range of applications, such as portable electronics, electric vehicles (EVs) and aerospace applications. Particularly, the emergence of a variety of nanostructured materials has driven the development of LIBs towards the next generation, which is featured with high specific energy and large power density. Herein, rolled-up nanotechnology is introduced for the design of strain-released materials as anodes of LIBs. Upon this approach, self-rolled nanostructures can be elegantly combined with different functional materials and form a tubular shape by relaxing the intrinsic strain, thus allowing for enhanced tolerance towards stress cracking. In addition, the hollow tube center efficiently facilitates electrolyte mass flow and accommodates volume variation during cycling. In this context, such structures are promising candidates for electrode materials of LIBs to potentially address their intrinsic issues. This work focuses on the development of superior structures of Si and SnO2 for LIBs based on the rolled-up nanotech. Specifically, Si is the most promising substitute for graphite anodes due to its abundance and high theoretical gravimetric capacity. Combined with the C material, a Si/C self-wound nanomembrane structure is firstly realized. Benefiting from a strain-released tubular shape, the bilayer self-rolled structures exhibit an enhanced electrochemical behavior over commercial Si microparticles. Remarkably, this behavior is further improved by introducing a double-sided carbon coating to form a C/Si/C self-rolled structure. With SnO2 as active material, an intriguing sandwich-stacked structure is studied. Furthermore, this novel structure, with a minimized strain energy due to strain release, exposes more active sites for the electrochemical reactions, and also provides additional channels for fast ion diffusion and electron transport. The electrochemical characterization and morphology evolution reveal the excellent cycling performance and stability of such structures.

Gegenwärtige Bestrebungen materialwissenschaftlicher Forschung beschäftigen sich unter anderem mit der Überführung zweidimensionaler Elemente elektronischer, optischer, plasmonischer oder magnetischer Funktionalität in den dreidimensionalen (3D) Raum. Dieser Ansatz vermag mittels Krümmung und struktureller Topologie bereits vorhandene Eigenschaften abzuändern beziehungsweise neue Funktionalitäten bereitzustellen. Vor allem Vektoreigenschaften wie die Magnetisierung kondensierter Materie lassen sich aufgrund der Brechung der Inversionssymmetrie in gekrümmten Flächen stark beeinflussen. Neben der Entwicklung diverser Vorgänge zur Herstellung 3D magnetischer Gegenstände sind geeignete Untersuchungsmethoden wie beispielsweise tomografische Abbildungen der Magnetisierung von Nöten, die maßgeblich die physikalischen Eigenschaften bestimmen. Die vorliegende Dissertationsschrift befasst sich mit der Abbildung von magnetischen Domänen in 3D gekrümmten Dünnschichten beruhend auf dem Effekt des zirkularen magnetischen Röntgendichroismus (XMCD). Die in diesem Zusammenhang entwickelte magnetische Röntgentomografie (MXT) basierend auf weicher Röntgenmikroskopie stellt eine zu Elektronenholografie und Neutronentomografie komplementäre Methodik dar, welche großes Anwendungspotential in der elementspezifischen Untersuchung magnetischer gekrümmter Flächen mit örtlicher Auflösung im Nanometerbereich aufweist. Die Schwierigkeit der Interpretation von Abbildungen magnetischer Strukturen in gekrümmten Flächen rührt von der Dreidimensionalität und der Vektoreigenschaft der Magnetisierung her. Die hierzu notwendigen Kenntnisse sind anhand von zwei topologisch verschiedenen Flächen in Form hemisphärischer Kappen und hohler Zylinder erschlossen worden. Die praktische Anwendung von MXT ist abschließend anhand der Rekonstruktion magnetischer Domänen in aufgerollten Dünnschichten mit zylindrischer Form verdeutlicht. / One of the foci of modern materials sciences is set on expanding conventional two-dimensional electronic, photonic, plasmonic and magnetic devices into the third dimension. This approach provides means to modify conventional or to launch novel functionalities by tailoring curvature and three-dimensional (3D) shape. The degree of effect is particularly high for vector properties like the magnetization due to an emergent inversion symmetry breaking. Aside from capabilities to design and synthesize 3D magnetic architectures, proper characterization methods, such as magnetic tomographic imaging techniques, need to be developed to obtain a thorough understanding of the system’s response under external stimuli. The main objective of this thesis is to develop a visualization technique that provides nanometer spatial resolution to image the peculiarities of the magnetic domain patterns on extended 3D curved surfaces. The proposed and realized concept of magnetic soft X-ray tomography (MXT), based on the X-ray magnetic circular dichroism (XMCD) effect with soft X-ray microscopies, has the potential to become a powerful tool to investigate element specifically an entirely new class of 3D magnetic objects with virtually any shape and magnetization. Imaging curved surfaces meets the challenge of three-dimensionality and requires a profound understanding of the recorded XMCD contrast. These experiences are gained by visualizing magnetic domain patterns on two distinct 3D curved surfaces, namely magnetic cap structures and rolled-up magnetic nanomembranes with cylindrical shape. The capability of MXT is demonstrated by reconstructing the magnetic domain patterns on 3D curved surfaces resembling hollow cylindrical objects.

Optical microcavities (OMs) are receiving increasing attention owing to their potential applications ranging from cavity quantum electrodynamics, optical detection to photonic devices. Recently, rolled-up structures have been demonstrated as OMs which have gained considerable attention owing to their excellent customizability. To fully exploit this customizability, asymmetric and topological rolled-up OMs are proposed and investigated in addition to conventional rolled-up OMs in this thesis. By doing so, novel phenomena and applications are demonstrated in OMs. The fabrication of conventional rolled-up OMs is presented in details. Then, dynamic mode tuning by a near-field probe is performed on a conventional rolled-up OM. Next, mode splitting in rolled-up OMs is investigated. The effect of single nanoparticles on mode splitting in a rolled-up OM is studied. Because of a non-synchronized oscillating shift for different azimuthal split modes induced by a single nanoparticle at different positions, the position of the nanoparticle can be determined on the rolled-up OM. Moreover, asymmetric rolled-up OMs are fabricated for the purpose of introducing coupling between spin and orbital angular momenta (SOC) of light into OMs. Elliptically polarized modes are observed due to the SOC of light. Modes with an elliptical polarization can also be modeled as coupling between the linearly polarized TE and TM mode in asymmetric rolled-up OMs. Furthermore, by adding a helical geometry to rolled-up structures, Berry phase of light is introduced into OMs. A -π Berry phase is generated for light in topological rolled-up OMs so that modes have a half-integer number of wavelengths. In order to obtain a deeper understanding for existing rolled-up OMs and to develop the new type of rolled-up OMs, complete theoretical models are also presented in this thesis.

Following the intensive development of isolated (i.e., not coupled with on-chip waveguide) vertically rolled-up microtube ring resonators (VRU-MRRs) for both active and passive applications, a variety of microtube-based devices has been realized. These include microcavity lasers, optical sensors, directional couplers, and active elements in lab-on-a-chip devices. To provide more advanced and complex functionality, the focus of tubular geometry research is now shifting toward (i) refined vertical light transfer in 3D stacks of multiple photonic layers and (ii) to make microfluidic cooling system in the integrated optoelectronic system. Based on this motivation, this PhD research is devoted to the demonstration and the implementation of monolithic integration of VRU-MRRs with photonic waveguides for 3D photonic integration and their optofluidic applications. Prior to integration, high-quality isolated VRU-MRRs on the flat Si substrate are firstly fabricated by the controlled release of differentially strained titanium-dioxide (TiO2) bilayered nanomembranes. The fabricated microtubes support resonance modes for both telecom and visible photonics. The outcome of the isolated VRU-MRRs is a record high Q (≈3.8×10^3) in the telecom wavelength range with optimum tapered optical fiber resonator interaction. To further study the optical modes in the visible and near infrared spectral range, μPL spectroscopy is performed on the isolated VRU-MRRs, which are activated by entrapping various sizes of luminescent nanoparticles (NPs) within the windings of rolled-up nanomembranes based on a flexible, robust and economical method. Moreover, it is realized for the first time, in addition to serving as light sources that NPs-aggregated in isolated VRU-MRRs can produce an optical potential well that can be used to trap optical resonant modes. After achieving all the required parameters for creating a high-quality TiO2 VRU-MRR, the monolithic integration of VRU-MRRs with Si nanophotonic waveguides is experimentally demonstrated, exhibiting a significant step toward 3D photonic integration. The on-chip integration is realized by rolling up 2D pre-strained TiO2 nanomembranes into 3D VRU-MRRs on a microchip which seamlessly expanded over several integrated waveguides. In this intriguing vertical transmission configuration, resonant filtering of optical signals at telecom wavelengths is demonstrated based on ultra-smooth and subwavelength thick-walled VRU-MRRs. Finally, to illustrate the usefulness of the fully integrated VRU-MRRs with photonic waveguides, optofluidic functionalities of the integrated system is investigated. In this work, two methods are performed to explore optofluidic applications of the integrated system. First, the hollow core of an integrated VRU-MRR is uniquely filled with a liquid solution (purified water) by setting one end of the VRU-MRRs in contact with a droplet placed onto the photonic chip via a glass capillary. Second, the outside of an integrated VRU-MRR is fully covered with a big droplet of liquid. Both techniques lead to a significant shift in the WGMs (Δλ≈46 nm). A maximum sensitivity of 140 nm/refractive index unit, is achieved. The achievements of this PhD research open up fascinating opportunities for the realization of massively parallel optofluidic microsystems with more functionality and flexibility for analysis of biomaterials in lab-on-a-tube systems on single chips. It also demonstrates 3D photonic integration in which optical interconnects between multiple photonic layers are required.

[pt] O principal objetivo deste trabalho foi avaliar a evolução microestrutural de dois tipos de nanocompósitos metal/cerâmico: Cu-10(por cento)Ni-1(por cento)Al2O3 (Cu-rich) e Ni-10(por cento)Cu-1(por cento)Al2O3 (Ni-rich) consolidadas em forma de fitas. A obtenção de nanoparticulas precursoras às fitas se deu por uma rota química, (que compreende a decomposição térmica de nitratos metálicos, originando óxidos coformados (CuO-NiO-Al2O3), seguido da redução seletiva destes por hidrogênio). O pó constituído de nanopartículas metálicas CuNi de 20nm a 100nm, com dispersão de nanopartículas ainda mais finas de Al2O3, foi submetido a pressão uniaxial a frio, em forma de pastilhas, e posteriormente sinterizado por 30 minutos. As pastilhas foram laminadas a frio com redução de espessura em 40, 60 e 80 por cento. As fitas assim produzidas foram recozidas a 600 graus Celsius nas amostras Cu-rich e a 900 graus Celsius nas Ni-rich, durante 5, 30 e 300 minutos, gerando diferentes estados microestruturais em virtude de fenômenos de recuperação, recristalização e crescimento de grão, na presença do Al2O3 na matriz metálica. O estudo detalhado da evolução microestrutural foi realizado por Microscopia Eletrônica de Varredura, Feixe de Íons Focalizado e Microscopia Eletrônica de Transmissão (MET), nos modos convencional e transmissão varredura (STEM), e em alta resolução (HRTEM). Tanto no MEV como no MET/STEM analises composicionais foram sistematicamente conduzidas por espectroscopia de dispersão de energia característica de raios x (EDXS). A preparação das amostras para MEV foi realizada por metodos metalogarficos convencionais e também submetidas a polimento por feixe de íons no instrumento MEV/FIB, quando necessário. As amostras transparentes ao feixe de elétrons para MET foram preparadas por métodos eletrolíticos convencionais e seletivos como o denominado jato duplo, assim como por feixe de íons no instrumento de precisão (PIPS) e em regiões especificas selecionadas extraindo lamelas através do FIB. Foi observado que as partículas cerâmicas não se dispersam homogeneamente na matriz metálica policristalina, mas se auto segregam em finos aglomerados seguindo o sentido da laminação e servindo como sítios preferenciais para a nucleação heterogênea de novos grãos, durante o fenômeno de recristalização no recozimento. Observa-se que nos lugares que o Al2O3 está presente o tamanho de grão, TG, é bem menor quando comparado com os lugares em ausência de Al2O3. De fato, observou-se sistematicamente que, principalmente nas amostras com alto grão de deformação ocorreram recristalização e crescimento de grão, gerando microestruturas bastante heterogêneas em quanto ao tamanho de grão, dando lugar a regiões da mostra com TG variando de 10nm a 100nm e regiões vizinhas na amostra com TG entre 1 um e 10 um. Medidas de microdureza comprovaram que as nanopartículas de Al2O3 agem como eficiente reforço, pois aumentou em até 100 porcento a dureza do material, quando comparado ao mesmo sem Al2O3. / [en] In this work it is evaluated the microstructural evolution of two types of metal/ceramic nanocomposites, Cu-10(percent)wt(percent)Ni-1(percent)Al2O3 (Cu-rich) and Ni-10Cu-1(percent)Al2O3 (Ni-rich), consolidated in ribbons. Initially, the precursor nanoparticles were obtained by a chemical route synthesis based on the thermal decomposition of Cu and Ni metal nitrates solution, as it generates co-formed oxides (CuO-NiOAl2O3). This material was selectively reduced by hydrogen in order to produce the nanocomposites. The CuNi matrix with particle size of about 20-100 nm containing a dispersion of even finer Al2O3 was uniaxially cold pressed into pellets and then aggregated by heating for 30 minutes. The treated pellets were cold rolled aiming a thickness reduction of 40, 60 and 80 (percent). The produced ribbons were then annealed at 600 degrees Celsius for Cu-rich samples and at 900 degrees Celsius for Nirich samples for periods of 5, 30 and 300 minutes. This step has produced different microstructural states due to phenomena of recovery, recrystallization and grain growth. The microstructural analysis was performed by Scanning Electron Microscopy (MEV), Focused Ion Beam (FIB), and Transmission Electron Microscopy (MET). All of the studies included the conventional and scanning (STEM) modes and high resolution (HRTEM). Particularly, the SEM and TEM / STEM compositional analyzes were conducted by x-ray energy dispersive spectroscopy (EDXS). The preparation of the samples for MEV was performed by conventional metallography, if required, the samples were subject to ion beam polishing in the MEV / FIB instrument. Electron transparent samples were prepared by conventional double jet electropolishing of thin foils, ion milling in precision instrument (PIPS) as well as selected lamellae prepared by Focus Ion Beam (FIB).These studies indicate that the ceramic particles are not homogeneously disperse in the polycrystalline metal matrix, but they selfsegregate in fine agglomerates following the direction of the cold rolled, and serve as preferential sites for the heterogeneous nucleation of new grains, due to recrystallization phenomenon, during annealing. It has also been observed that in the regions with the presence of Al2O3 the grain size of the nanoparticles is smaller. Actually, in the samples with high grain of deformation, recrystallization and grain growth occurred, generating highly heterogeneous size for the microstructures (range about 50nm to 10um). Microhardness measurements have showed that Al2O3 is a good reinforcement, as it increased the hardness of the material by up to 100 percent when compared with the same material without Al2O3.

.L’objectif de cette étude était, en premier lieu, de mettre en place en Thaïlande un testd’adhésion par traction-écaillage sur une machine de traction classique (test« macroscopique »), de le comparer au test « microscopique » Grenoblois fonctionnant dansla chambre du MEB et de l’utiliser pour évaluer l’adhérence des calamines de process sur desaciers industriels. Deux paramètres ont été étudiés, la vitesse de déformation et la teneur desaciers en silicium. Il apparaît que l’écaillage des calamines au cours du test augmente quandaugmente la vitesse de déformation. Une vitesse de déformation élevée entraîne unedéformation au premier écaillage plus faible, donc une adhérence mesurée plus faible. Ceteffet est lié aux phénomènes de relaxation. On a pu alors montrer que la présence d’oxyde(s)contenant Si, situé(s) à l’interface avec le métal, augmentait l’adhérence. Les étudesd’oxydation dans la vapeur d’eau qui ont aussi été réalisées ont révélé que la présence desilicium réduisait la vitesse d’oxydation. En augmentant la teneur en Si, les couches defayalite et de wüstite s’épaississent ; par contre, les couches externes s’amincissent. Pour lesaciers contenant du cuivre, la vitesse d’oxydation est réduite quand la teneur en Cu estaugmentée. De la même façon, les couches internes sont plus épaisses et on observe uneaugmentation du nombre de précipités de Cu quand la teneur en cet élément augmente. / The purpose of this study was first to develop in Thailand a “macroscopic” adhesion testusing a conventional tensile machine, to compare it to the micro-tensile test used in Grenobleand sitting in the SEM chamber, and to use it for measuring adhesion of scales grown duringprocessing on industrial steels. Parameters affecting the test, i.e. strain rate and Si content ofsteels were investigated. The results showed that spallation of scales during strainingincreased with increasing tensile strain rate. A higher strain rate resulted in lower straininitiating the first spallation and lower mechanical adhesion of scales, which could beexplained by a relaxation effect. Oxide containing Si existed at the steel-scale interface andpromoted adhesion of scales. Oxidation studies were also performed, and the behaviour inwater vapour of steels with different contents of Si and Cu was investigated. Increasing Sicontent tended to decrease oxidation rate. It also resulted in the thickening of the wüstite andfayalite layers which formed by internal oxidation. When Si in steel increased, theintermediate (FeO + Fe3O4) and outermost (Fe2O3 sitting on Fe3O4) layers formed by externaloxidation were thinner. For Cu containing steel, increasing Cu content tended to decrease theoxidation rate. It also decreased the innermost and intermediate layers and resulted in moreCu precipitates along steel-scale interface.

Medical devices have made a big step forward in the past decades. One of the most noticeable medical events of the twenties century was the development of long-lasting, wireless electronic implants such as identification tags, pacemakers and neuronal stimulators. These devices were only made possible after the development of small scale radio frequency electronics. Small radio electronic circuits provided a way to operate in both transmission and reception mode allowing an implant to communicate with an external world from inside a living organism. Bidirectional communication is a vital feature that has been increasingly implemented in similar systems to continuously record biological parameters, to remotely configure the implant, or to wirelessly stimulate internal organs. Further miniaturisation of implantable devices to make the operation of the device more comfortable for the patient requires rethinking of the whole radio system concept making it both power efficient and of high performance. Nowadays, high data throughput, large bandwidth, and long term operation requires new radio systems to operate at UHF (ultra-high frequency) bands as this is the most suitable for implantable applications. For instance, the MICS (Medical Implant Communication System) band was introduced for the communication with implantable devices. However, this band could only enable communication at low data rates. This was acceptable for the transmission of telemetry data such as heart beat rate, respiratory and temperature with sub Mbps rates. Novel developments such as neuronal and prosthetic implants require significantly higher data rates more than 10 Mbps that can be achieved with large bandwidth communicating systems operating at higher frequencies in a GHz range. Higher operating frequency would also resolve a strong issue of MICS devices, namely the scale of implants defined by dimensions of antennas used at this band. Operation at 2.4 GHz ISM band was recognized to be the most adequate as it has a moderate absorption in the human body providing a compromise between an antenna/implant scale and a total power efficiency of the communicating system. This thesis addresses a key challenge of implantable radio communicating systems namely an efficient and small scale antenna design which allows a high yield fabrication in a microelectronic fashion. It was demonstrated that a helical antenna design allows the designer to precisely tune the operating frequency, input impedance, and bandwidth by changing the geometry of a self-assembled 3D structure defined by an initial 2D planar layout. Novel stimuli responsive materials were synthesized, and the rolled-up technology was explored for fabrication of 5.5-mm-long helical antenna arrays operating in ISM bands at 5.8 and 2.4 GHz. Characterization and various applications of the fabricated antennas are successfully demonstrated in the thesis.

Optoplasmonic microtube cavities, the combination of dielectric microcavities and noble metal layers, allow for the interactions between photonic modes and surface plasmons, leading to several novel phenomena and promising applications. In this thesis, the hybrid modes with different plasmon-types of evanescent field in the optoplasmonic microtube cavities are discussed. The basic physical mechanism for the generation of plasmon-type field is comprehensively investigated based on an effective potential approach. In particular, when the cavity wall becomes ultra-thin, the plasmon-type field can be greatly enhanced, and the hybrid modes are identified as strong photon-plasmon hybrid modes which are experimentally demonstrated in the metal-coated rolled-up microtube cavities. By designing a metal nanocap onto microtube cavities, angle-dependent tuning of hybrid photon-plasmon modes are realized, in which TE and TM polarized modes exhibit inverse tuning trends due to the polarization match/mismatch. And a novel sensing scheme is proposed relying on the intensity ratio change of TE and TM modes instead of conventionally used mode shift. In addition, localized surface plasmon resonances coupled to resonant light is explored by designing a vertical metal nanogap on microtube cavities. Selective coupling of high-order axial modes is demonstrated depending on spatial-location of the metal nanogap. A modified quasi-potential well model based on perturbation theory is developed to explain the selective coupling mechanism. These researches systematically explore the design of optoplasmonic microtube cavities and the mechanism of photon-plasmon coupling therein, which provide a novel platform for the study of both fundamental and applied physics such as the enhanced light-matter interactions and label-free sensing.