Processing of broadband signals induced on an antenna array using a tapped delay line filter and a set of steering delays has two problems. Firstly one needs to manipulate large matrices to estimate the filter coefficients. Secondly the use of steering delays is not only cumbersome but implementation errors cause loss of system performance. This thesis looks at both of these problems and presents elegant solutions by developing and studying a design method referred to as the DFT method, which does not require steering delays and is computationally less demanding compared to existing methods. Specifically the thesis studies and compares the performance of a time domain element space beamformer using the proposed method and that using an existing method, and develops the DFT method when the processor is implemented in partitioned form. The study presented in the thesis shows that the processors using the DFT method are robust to look direction errors and require less computation than that using the existing method for comparable performance. The thesis further introduces a broadband beamformer design which does not require any steering delays between the sensors and the tapped delay line section as is presently the case. It has the capability of steering the array in an arbitrary direction with a specified frequency response in the look direction while canceling unwanted uncorrelated interferences. The thesis presents and compares the performance of a number of techniques to synthesize an antenna pattern of a broadband array. These techniques are designed to produce isolated point nulls as well as broad sector nulls and to eliminate the need for the steering delays. Two of the pattern synthesis techniques presented in the thesis allow optimization against unwanted interferences in unknown directions. The techniques allow formulation of a beamforming problem such that the processor is not only able to place nulls in specified directions but also able to cancel directional interferences in unknown directions along with a specified frequency response in the look direction over a band of interest. The thesis also presents a set of directional constraints such that one does not need steering delays and an array can be constrained in an arbitrary direction with a specified frequency response. The constraints presented in the thesis are simple to implement. Based on these constraints a pattern synthesis technique for broadband antenna array is also presented.

Les systèmes multi-antennaires (Multiple-Input Multiple-Ouput ou MIMO) dans le domaine des communications numériques permettent d'améliorer la transmission des données selon deux principaux paramètres souvent antagonistes : le débit d'information et la fiabilité de transmission estimée en terme de probabilité d'erreurs binaire moyenne (PEB). Avec de tels systèmes, la connaissance du canal à l'émission (Channel State Information ou CSI) est un point-clé pour diminuer la PEB grâce à différentes stratégies d'allocations de puissance. Ainsi, un précodeur linéaire à l'émission associé à un décodeur linéaire à la réception peuvent optimiser un critère particulier grâce à cette information. Il en résulte une famille importante de précodeurs dénommée «précodeurs diagonaux» : le système MIMO est équivalent à des sous-canaux SISO indépendants. Les critères optimisés sont par exemple la minimisation de l'erreur quadratique moyenne (EQMM), la maximisation de la capacité (WF), obtenir des PEB égales pour tous les flux de données (EE), la maximisation du RSB post-traitement (max-SNR) ou la qualité de service (QdS). L'équipe TST a récemment élaboré un nouveau précodeur non diagonal basé sur la maximisation de la distance minimale entre symboles de la constellation de réception (max-dmin ). L'enjeu de cette thèse est d'estimer les performances en terme de PEB de ce nouveau précodeur et de les comparer avec les méthodes existantes à savoir le code d'Alamouti et les précodeurs diagonaux. Nous nous sommes intéressés en particulier à la démonstration de l'ordre de diversité maximal du max-dmin puis à la détermination d'une bonne approximation de sa PEB. Le précodeur max-dmin est ensuite associé à de la diversité de polarisation permettant de réduire le coût et l'occupation spatiale d'un système MIMO. Malgré l'introduction de corrélation, les performances proposées par le max-dmin demeurent intéressantes. Nous avons ensuite proposé une extension du précodeur max-dmin permettant de supprimer la limitation à deux sous-canaux : les grands systèmes MIMO sont mieux exploités avec plus de deux sous-canaux.

<p>With the 1999 introduction of IEEE 802.11b, the 2.4 GHz Wireless Local Area Network (WLAN) standard, the WLAN market finally began to experience the growth levels that had been expected for so long. Now, 5 GHz solutions, with the IEEE 802.11a standard leading the way, offer higher throughput and more efficient use of the spectrum. Just as the 2.4 GHz band, the 5 GHz band is unlicensed. A common concern to all unlicensed bands is interference between devices using the spectrum. Furthermore, in the 5 GHz band, WLAN cells can interfere with radar systems operating at the same frequencies. </p><p>This report describes a software model, WOK, suitable for simulations of IEEE 802.11a WLANs operating in various environments and under various ambient conditions. The WOK model can be configured extensively with respect to topology, traffic behavior, channel models, signal attenuation, interference sources and radar systems. </p><p>Further, the concepts of Dynamic Frequency Selection (DFS) and link adaptation are explored in the context of the IEEE 802.11a standard. DFS aims to avoid channels occupied by radar systems and link adaptation aims to maximize the throughput based on current ambient conditions. A DFS algorithm and a link adaptation algorithm are implemented at the Medium Access Control (MAC) layer and evaluated using the WOK model.</p>

Mechanomyography (MMG) has been proposed as a control modality for alternative access technologies for individuals with disabilities. However, MMG recordings are highly susceptible to contamination from limb movements. Pressure-based transducers are touted to be the most robust to external movement although there is some debate about their optimal chamber geometry, in terms of low frequency gain and spectral flatness. To investigate the question of preferred geometry, transducers with varying chamber shapes were designed, manufactured and tested. The best performance was achieved with a transducer consisting of a low-frequency MEMS microphone, a 4 micron thick aluminized mylar membrane and a rigid conical chamber 7 mm in diameter and 5 mm in height. Furthermore, microphone-derived MMG spectra were found to be less influenced by motion artifact than corresponding accelerometer-derived spectra. However, artifact harmonics were present in both spectra, suggesting that bandpass filtering may not remove artifact influences permeating into MMG frequency bands.

Mechanomyography (MMG) has been proposed as a control modality for alternative access technologies for individuals with disabilities. However, MMG recordings are highly susceptible to contamination from limb movements. Pressure-based transducers are touted to be the most robust to external movement although there is some debate about their optimal chamber geometry, in terms of low frequency gain and spectral flatness. To investigate the question of preferred geometry, transducers with varying chamber shapes were designed, manufactured and tested. The best performance was achieved with a transducer consisting of a low-frequency MEMS microphone, a 4 micron thick aluminized mylar membrane and a rigid conical chamber 7 mm in diameter and 5 mm in height. Furthermore, microphone-derived MMG spectra were found to be less influenced by motion artifact than corresponding accelerometer-derived spectra. However, artifact harmonics were present in both spectra, suggesting that bandpass filtering may not remove artifact influences permeating into MMG frequency bands.

Η διαμόρφωση με πολύπλεξη συχνότητας ορθογωνίων φερουσών (Orthogonal Frequency Division Multiplexing - OFDM) έχει εδραιωθεί ως μία από τις επικρατέστερες μεθόδους διαμόρφωσης για την υψηλού ρυθμού μετάδοση πληροφορίας μέσω ασύρματων μέσων. Σε ένα σύστημα OFDM, ένα από τα βασικότερα και υπολογιστικά πολυπλοκότερα τμήματα είναι ο υπολογισμούς του Ταχύ Μετασχηματισμού Fourier. Αντικείμενο της εργασίας αυτής είναι η μελέτη της χρήσης εναλλακτικής αριθμητικής για την υλοποίηση κυκλωμάτων FFT. Τυπικά, τέτοιου είδους κυκλώματα υλοποιούνται χρησιμοποιώντας κάποια γραμμική αναπαράσταση σταθερής υποδιαστολής. Στη βιβλιογραφία έχουν προταθεί υλοποιήσεις του FFT με χρήση του Λογαριθμικού Συστήματος Αρίθμησης (Logarithmic Numbering System – LNS) και έχουν αναφερθεί κέρδη για συγκεκριμένους παράγοντες όπως το σφάλμα κβαντισμού, η επιφάνεια ολοκλήρωσης και η κατανάλωση ισχύος. Η αποδοτικότητα αυτών των λύσεων ερευνάται για τη συγκεκριμένη περίπτωση της εφαρμογής του FFT σε OFDM modems. Εστιάζοντας στην περίπτωση του FFT 64 σημείων για OFDM modem για ασύρματα δίκτυα 802.11a, μία από τις πλέον επιτυχημένες αρχιτεκτονικές που έχουν προταθεί για την υλοποίηση του, στηρίζεται στη λογική του FFT γραμμής – στήλης και παρουσιάζει έναν τρόπο πραγματοποίησης του υπολογισμού χωρίς κανένα ψηφιακό πολλαπλασιαστή. Με το βασικό πλεονέκτημα της λογαριθμικής αναπαράστασης να είναι η απλοποίηση των κυκλωμάτων πολλαπλασιασμού (με ταυτόχρονη όμως αύξηση του κόστους για την πραγματοποίηση προσθέσεων), δείχνεται ότι τελικά η υλοποίηση ενός FFT αμιγώς σε LNS δεν είναι προτιμητέα. Αν και η αρχιτεκτονική του FFT γραμμής – στήλης μπορεί να προσφέρει υψηλή απόδοση με χαμηλό κόστος υλοποίησης, παρουσιάζει μια σειρά από αδυναμίες, που σχετίζονται κυρίως με τη χρήση ειδικών κυκλωμάτων για την εκτέλεση των πολλαπλασιασμών με τις σταθερές που εμφανίζονται στον FFT (twiddle factors). Για την αντιμετώπιση αυτών των περιορισμών προτείνεται η εισαγωγή του LNS σε κάποια τμήματα του κυκλώματος του FFT, οδηγώντας έτσι στη δημιουργία ενός συστήματος μικτής αναπαράστασης. Σε τέτοιου είδους υβριδικά συστήματα τίθενται δύο βασικά ζητήματα. Το πρώτο αφορά τον ορισμό της ισοδυναμίας μεταξύ των διαφορετικών αναπαραστάσεων και το δεύτερο τον αποδοτικό τρόπο υλοποίησης των κυκλωμάτων μετατροπής από το ένα αριθμητικό σύστημα στο άλλο. Τυπικά, τα κριτήρια ισοδυναμίας που επιλέγονται είναι αυστηρά μαθηματικά ορισμένα, όπως για παράδειγμα ο Λόγος Σήματος προς Θόρυβο (Signal-to-Noise Ratio - SNR) ή το Μέσο Σχετικό Σφάλμα Αναπαράστασης (Average Relative Representation Error – ARRE). Στη συγκεκριμένη εργασία ακολουθείται μια λιγότερο δεσμευτική προσέγγιση, ορίζοντας την ισοδυναμία δύο αναπαραστάσεων με βάση την τελική απόδοση του συστήματος OFDM όσον αφορά το ρυθμό λαθών στο δέκτη (Bit Error Rate - BER). Με βάση αυτή τη λογική, αποδεικνύεται ότι μπορούν να χρησιμοποιηθούν αναπαραστάσεις πολύ μικρού μεγέθους λέξης και οι προσεγγίσεις που χρειάζεται να γίνουν κατά τις μετατροπές μεταξύ των δύο συστημάτων δεν είναι ανάγκη να είναι ιδιαίτερα ακριβείς. Έτσι, τα σχετικά κυκλώματα μπορούν να υλοποιηθούν αποδοτικά και με μικρό κόστος. Η υλοποίηση δύο συστημάτων για τον FFT 64 σημείων, ένα βασισμένο αποκλειστικά σε γραμμική αναπαράσταση σταθερής υποδιαστολής και ένα υβριδικό που χρησιμοποιεί γραμμική και λογαριθμική αναπαράσταση, δείχνει ότι χωρίς διαφορές όσον αφορά το BER και την καθυστέρηση (delay), η υβριδική προσέγγιση απαιτεί μικρότερη επιφάνεια ολοκλήρωσης και παρουσιάζει σημαντικά χαμηλότερη κατανάλωση ισχύος. / Orthogonal Frequency Division Multiplexing (OFDM) has been established as one of the most prevalent methods for high data rate transmission through wireless channels. In an OFDM communication system, one of the fundamental and most computationally intensive parts is the computation of the Fast Fourier Transform (FFT). The subject of this thesis is to investigate the use of alternative arithmetic representation systems for the implementation of FFT circuits. Typically, these circuits are implemented using linear fixed-point representations. In literature, implementations of the FFT using the Logarithmic Numbering System (LNS) have been proposed and significant gains in quantization errors, chip area and power consumption have been reported. The effectiveness of these proposals in the case of the FFT for OFDM systems is investigated. Focusing on the case of the 64-point FFT for an OFDM modem for an 802.11a wireless network, one of the most efficient architectures proposed is based on the concept of row-column FFT and presents a way of implementing the computation without using any digital (non-fixed input) multiplier. The most important feature of the LNS representation is the fact that multiplication operations turn to mere additions, thus there are significant implementation gains. On the downside though, addition in LNS is very expensive. Combining the aforementioned, it is shown that the implementation of the whole FFT computation in LNS is not a preferable solution. Although the row-column FFT architecture may offer high performance and low implementation cost, it presents a number of deficiencies mainly due to the fact that special purpose circuits are used to perform the multiplications with the complex constants (twiddle factors) that appear in the computation. In order to alleviate these deficiencies, it is proposed to use the LNS representation in some parts of the FFT circuit, thus forming a hybrid-representation system. In hybrid-representation systems two major issues are raised. The first one is how to define equivalence between the arithmetic representation systems used and the second one is related to the cost of the circuits required to perform the conversions between the numbers of the different arithmetic systems. Typically, the equivalence criterion used is mathematically defined and metrics like the Signal-to-Noise Ratio (SNR) or Average Relative Representation Error (ARRE) are commonly used. In this report, a less restrictive metric is used: two arithmetic representations are defined to be equal if the Bit Error Rate (BER) performance of the overall OFDM system is equal. Using this approach, it is shown that short word-length representations may be used and the conversions between the linear and logarithmic systems need not be very accurate. This results in great simplification of the conversion process and the respected circuits can be implemented with low cost. For comparison, two 64-point FFT systems have been implemented, one using a linear fixed-point 2’s complement representation and one using both linear and LNS representation. Without any differences in BER performance and circuit delay, the hybrid-representation system requires less chip area and consumes significantly lower power.

Most of the modern wireless communication systems as WiMAX, DVB-NGH, WiFi, HSPA+ and 4G have adopted the use of multiple antennas at the transmitter and the receiver, called multiple-input multiple-output (MIMO). Space time coding for MIMO systems is a promising technology to increase the data rate and enhance the reliability of wireless communications. Space-time block codes (STBCs) are commonly designed according to the rank-determinant criteria suitable at high signal to noise ratios (SNRs). In contrast, wireless communication standards employ MIMO technology with capacity-approaching forward-error correcting (FEC) codes like turbo codes and low-density parity-check (LDPC) codes, ensuring low error rates even at low SNRs. In this thesis, we investigate the design of STBCs for MIMO systems with capacity-approaching FEC codes. We start by proposing a non-asymptotic STBC design criterion based on the bitwise mutual information (BMI) maximization between transmitted and soft estimated bits at a specific target SNR. According to the BMI criterion, we optimize several conventional STBCs. Their design parameters are shown to be SNR-dependent leading to the proposal of adaptive STBCs. Proposed adaptive STBCs offer identical or better performance than standard WiMAX profiles for all coding rates, without increasing the detection complexity. Among them, the proposed adaptive trace-orthonormal STBC can pass continuously from spatial multiplexing, suitable at low SNRs and therefore at low coding rates, to the Golden code, optimal at high SNRs. Uncorrelated, correlated channels and transmit antenna selection are considered. We design adaptive STBCs for these cases offering identical or better performance than conventional non-adaptive STBCs. In addition, conventional STBCs are designed in a way achieving the asymptotic DMT frontier. Recently, the finite-SNR DMT has been proposed to characterize the DMT at finite SNRs. Our last contribution consists of the derivation of the exact finite-SNR DMT for MIMO channels with dual antennas at the transmitter and/or the receiver. Both uncorrelated and correlated Rayleigh fading channels are considered. It is shown that at realistic SNRs, achievable diversity gains are significantly lower than asymptotic values. This finite-SNR could provide new insights on the design of STBCs at operational SNRs.

Multipath propagation and mobility in wireless communication systems give rise to variations in the amplitude and phase of the transmitted signal, commonly referred to as fading. Many wireless applications are affected by slowly varying fading, where the channel is non-ergodic, leading to non-reliable transmission during bad channel realizations. These communication scenarios are well modeled by the block-fading channel, where the reliability is quantatively characterized by the outage probability. This thesis focuses on the analysis and design of adaptive transmission schemes to improve the outage performance of both single- and multiple-antenna transmission over the block-fading channel, especially for the cases where discrete input constellations are used. Firstly, a new lower bound on the outage probability of non-adaptive transmission is proposed, providing an efficient tool for evaluating the performance of non-adaptive transmission. The lower bound, together with its asymptotic analysis, is essential for efficiently designing the adaptive transmission schemes considered in the thesis. Secondly, new power allocation rules are derived to minimize the outage probability of fixed-rate transmission over block-fading channels. Asymptotic outage analysis for the resulting schemes is performed, revealing important system design criteria. Furthermore, the thesis proposes novel suboptimal power allocation rules, which enjoy low-complexity while suffering minimal losses as compared to the optimal solution. Thus, these schemes facilitate power adaptation in low-cost devices. Thirdly, the thesis considers incremental-redundancy automatic-repeat-request (INR-ARQ) strategies, which perform adaptive transmission based on receiver feedback. In particular, the thesis concentrates on multi-bit feedback, which has been shown to yield significant gains in performance compared to conventional single-bit ARQ schemes. The thesis proposes a new information-theoretic framework for multi-bit feedback INR-ARQ, whereby the receiver feeds back a quantized version of the accumulated mutual information. Within this framework, the thesis presents an asymptotic analysis which yields the large gains in outage performance offered by multi-bit feedback. Furthermore, the thesis proposes practical design rules, which further illustrates the benefits of multi-bit feedback in INR-ARQ systems. In short, the thesis studies the outage performance of transmission over block-fading channels. Outage analysis is performed for non-adaptive and adaptive transmission. Improvements for the existing adaptive schemes are also proposed, leading to either lower complexity requirements or better outage performance. Still, further research is needed to bring the benefits offered by adaptive transmission into practical systems. / Thesis (PhD)--University of South Australia, 2010

Multipath propagation and mobility in wireless communication systems give rise to variations in the amplitude and phase of the transmitted signal, commonly referred to as fading. Many wireless applications are affected by slowly varying fading, where the channel is non-ergodic, leading to non-reliable transmission during bad channel realizations. These communication scenarios are well modeled by the block-fading channel, where the reliability is quantatively characterized by the outage probability. This thesis focuses on the analysis and design of adaptive transmission schemes to improve the outage performance of both single- and multiple-antenna transmission over the block-fading channel, especially for the cases where discrete input constellations are used. Firstly, a new lower bound on the outage probability of non-adaptive transmission is proposed, providing an efficient tool for evaluating the performance of non-adaptive transmission. The lower bound, together with its asymptotic analysis, is essential for efficiently designing the adaptive transmission schemes considered in the thesis. Secondly, new power allocation rules are derived to minimize the outage probability of fixed-rate transmission over block-fading channels. Asymptotic outage analysis for the resulting schemes is performed, revealing important system design criteria. Furthermore, the thesis proposes novel suboptimal power allocation rules, which enjoy low-complexity while suffering minimal losses as compared to the optimal solution. Thus, these schemes facilitate power adaptation in low-cost devices. Thirdly, the thesis considers incremental-redundancy automatic-repeat-request (INR-ARQ) strategies, which perform adaptive transmission based on receiver feedback. In particular, the thesis concentrates on multi-bit feedback, which has been shown to yield significant gains in performance compared to conventional single-bit ARQ schemes. The thesis proposes a new information-theoretic framework for multi-bit feedback INR-ARQ, whereby the receiver feeds back a quantized version of the accumulated mutual information. Within this framework, the thesis presents an asymptotic analysis which yields the large gains in outage performance offered by multi-bit feedback. Furthermore, the thesis proposes practical design rules, which further illustrates the benefits of multi-bit feedback in INR-ARQ systems. In short, the thesis studies the outage performance of transmission over block-fading channels. Outage analysis is performed for non-adaptive and adaptive transmission. Improvements for the existing adaptive schemes are also proposed, leading to either lower complexity requirements or better outage performance. Still, further research is needed to bring the benefits offered by adaptive transmission into practical systems. / Thesis (PhD)--University of South Australia, 2010

With the 1999 introduction of IEEE 802.11b, the 2.4 GHz Wireless Local Area Network (WLAN) standard, the WLAN market finally began to experience the growth levels that had been expected for so long. Now, 5 GHz solutions, with the IEEE 802.11a standard leading the way, offer higher throughput and more efficient use of the spectrum. Just as the 2.4 GHz band, the 5 GHz band is unlicensed. A common concern to all unlicensed bands is interference between devices using the spectrum. Furthermore, in the 5 GHz band, WLAN cells can interfere with radar systems operating at the same frequencies. This report describes a software model, WOK, suitable for simulations of IEEE 802.11a WLANs operating in various environments and under various ambient conditions. The WOK model can be configured extensively with respect to topology, traffic behavior, channel models, signal attenuation, interference sources and radar systems. Further, the concepts of Dynamic Frequency Selection (DFS) and link adaptation are explored in the context of the IEEE 802.11a standard. DFS aims to avoid channels occupied by radar systems and link adaptation aims to maximize the throughput based on current ambient conditions. A DFS algorithm and a link adaptation algorithm are implemented at the Medium Access Control (MAC) layer and evaluated using the WOK model.