Today Atlas Copco Rock Drills AB hasn’t got any method to determine how many warning alarms they need on their machines and how they should be mounted to use their full potential. At the moment a travel alarm is usually placed in the front of the machine and a reverse alarm in the back. Then a measurement of the sound pressure level around the machine is performed to see if it is enough to pass the limit according to different ISO-standards. Otherwise they have to mount some extra alarms and then do the measurements again until the standards are fulfilled. The aim of this thesis work is to develop a method for determine how many alarms Atlas Copco Rock Drills AB need on the machines, and also how they should be mounted to fulfil the different criteria according to ISO-standards in the early phase of construction. From the different divisions within Atlas Copco Rock Drills AB (LHD, SDE and TME) arrived four different alarms, which are used on their machines. Sound pressure level measurements were conducted on these, in the anechoic chamber at audiological research centre at the university hospital in Örebro. In the LMS Test.Lab software a measurement sphere was built around the horns and based on the data obtained at the anechoic chamber sound directivity plots were made. Together with earlier machine measurement data from Atlas Copco Rock Drills AB, an Excel program was made constituting an example of how the horns should be mounted. LHD = Loaders and trucks/underground rock excavation SDE = Surface drilling equipment TME = Tunnelling and mining equipment / Idag har Atlas Copco Rock Drills AB inte någon metod för att bestämma hur många varningsalarm som behövs på sina maskiner samt var de ska placeras så de utnyttjar sin fulla potential. I nuläget monteras ett signalhorn vid främre delen och ett backlarm i bakre delen av maskinen. Sedan utförs en ljudtrycksmätning runt maskinen för att kontrollera om man uppfyller kraven från olika ISO-standader. Annars monteras fler alarm och mätningen utförs på nytt tills standarderna uppfylls. Detta examensarbete har som mål att ta fram en metod som bestämmer hur många alarm Atlas Copco Rock Drills AB behöver på sina maskiner, samt hur de skall placeras för att uppfylla kriterierna från olika ISO-standarder redan i konstruktionsstadiet.  Från de olika avdelningarna inom Atlas Copco Rock Drills AB (LHD, SDE och TME) mottogs fyra olika alarm, som används på maskinerna. På dessa utfördes ljudtrycksmätningar i det ekofria rummet vid audiologiskt forskningscentrum på universitetssjukhuset i Örebro. I programmet LMS Test.Lab byggdes en sfär av mätpunkter runt alarmen och baserat på insamlade data från det ekofria rummet konstruerades direktivitetsdiagram. Tillsammans med data som Atlas Copco Rock Drills AB redan hade från tidigare mätningar på maskiner gjordes ett Excel-program, som ger ett exempel på hur alarmen bör monteras. LHD = Loaders and trucks/underground rock excavation SDE = Surface drilling equipment TME = Tunnelling and mining equipment

Vertical axis wind turbines (VAWTs) have with time been outrivaled by the today common and economically feasible horizontal axis wind turbines (HAWTs). However, VAWTs have several advantages such as the possibility to put the drive train at ground level, lower noise emissions and better scaling behavior which still make them interesting for research. The work within this thesis is made in collaboration between the Department of Construction and Energy Engineering at Halmstad University and the Division for Electricity at Uppsala University. A 200 kW VAWT owned by the latter and situated close to Falkenberg in the southwest of Sweden has been the main subject of the research even if most learnings has been generalized to fit a typical vertical turbine. This particular turbine has a wooden tower which is semi-guy-wired, i.e. the tower is both firmly attached to the ground and supported by guy-wires. This thesis has two main topics both regarding VAWTs: eigenfrequency of the tower and the noise generated from the turbine. The eigenfrequency of a semi-guy-wired tower is studied and an analytical expression describing this is produced and verified by experiments and simulations. The eigenfrequency of the wire itself and how it is affected by wind load are also studied.  The noise characteristics of VAWTs have been investigated, both theoretically and by noise measurement campaigns. Both noise emission and frequency distribution of VAWTs has been studied. The work has resulted in analytical expressions for tower and wire eigenfrequency of a semi-guy-wired tower as well as recommendations for designing future towers for VAWTs. The noise emission of VAWTs has been studied and proven low compared to HAWTs. The noise frequency distribution of the 200 kW VAWT differs significantly from that of a similar size HAWTs with for example lower levels for frequencies below 3000 Hz.

This Master´s thesis deals with principles of determination of the sound power level. At the very beginning there is an explanation of important concepts. Afterwards there is an overview of standards that deal with the sound power level determination, including the ČSN EN ISO 9614-1 standard which is used for the experiment. Last but not least, there is described the experiment, consisting of several measurements of the same object, but every time with different configuration of measuring and sound reflective surfaces.

Vertical axis wind turbines (VAWTs) have with time been outrivaled by the today common and economically feasible horizontal axis wind turbines (HAWTs). However, VAWTs have several advantages such as the possibility to put the drive train at ground level, lower noise emissions and better scaling behavior which still make them interesting for research. The work within this thesis is made in collaboration between the Department of Construction and Energy Engineering at Halmstad University and the Division for Electricity at Uppsala University. A 200 kW VAWT owned by the latter and situated close to Falkenberg in the southwest of Sweden has been the main subject of the research even if most learnings has been generalized to fit a typical vertical turbine. This particular turbine has a wooden tower which is semi-guy-wired, i.e. the tower is both firmly attached to the ground and supported by guy-wires. This thesis has two main topics both regarding VAWTs: eigenfrequency of the tower and the noise generated from the turbine. The eigenfrequency of a semi-guy-wired tower is studied and an analytical expression describing this is produced and verified by experiments and simulations. The eigenfrequency of the wire itself and how it is affected by wind load are also studied.  The noise characteristics of VAWTs have been investigated, both theoretically and by noise measurement campaigns. Both noise emission and frequency distribution of VAWTs has been studied. The work has resulted in analytical expressions for tower and wire eigenfrequency of a semi-guy-wired tower as well as recommendations for designing future towers for VAWTs. The noise emission of VAWTs has been studied and proven low compared to HAWTs. The noise frequency distribution of the 200 kW VAWT differs significantly from that of a similar size HAWTs with for example lower levels for frequencies below 3000 Hz.

Vertical-axis wind turbines (VAWTs) have with time been outrivaled by the today more common and economically feasible horizontal-axis wind turbines (HAWTs). However, VAWTs have several advantages which still make them interesting, for example, the VAWTs can have the drive train at ground level and it has been argued that they have lower noise emission. Other proposed advantages are suitability for both up-scaling and floating offshore platforms. The work within this thesis is made in collaboration between Halmstad University and Uppsala University. A 200-kW semi-guy-wired VAWT H-rotor, owned by Uppsala University but situated in Falkenberg close to Halmstad, has been the main subject of the research although most results can be generalized to suit a typical H-rotor. This thesis has three main topics regarding VAWTs: (1) how the wind energy extraction is influenced by turbulence, (2) aerodynamical noise generation and (3) eigenfrequencies of the semi-guy-wired tower. The influence from turbulence on the wind energy extraction is studied by evaluating logged operational data and examining how the power curve and the tip-speed ratio for maximum Cp is impacted by turbulence. The work has showed that the T1-turbine has a good ability to extract wind energy at turbulent conditions, indicating an advantage in energy extraction at turbulent sites for VAWTs compared to HAWTs.The noise characteristics are studied experimentally, and models of the two most likely aerodynamic noise mechanisms are applied. Here, inflow-turbulence noise is deemed as the prevailing noise source rather than turbulent-boundary-layer trailing-edge noise (TBL-TE) which is the most important noise mechanism for HAWTs. The overall noise emission has also been measured and proven low compared to similar sized HAWTs. The eigenfrequencies of a semi-guy-wired tower are also studied. Analytical expressions describing the first-mode eigenfrequency of both tower and guy wire has been derived and verified by experiments and simulations.

This diploma thesis deals with comparing noise levels of three side vents of different constructions, which are used for distribution and directing of ventilation air in a cabin of an automobile. The fundamental knowledge of the physical and physiological acoustics is described in the introduction part of this study. Following the introduction part there is a brief explanation of the car air conditioning system (HVAC system) as well as are explained the acoustic properties of specific elements of this system. The study also deals with dividing ventilation vents and describes the vast traceable types of automobile vents. Prior to the description of the experiment, which was conducted as a part of this study, the procedures and results of the measurements carried out in other theses are explained. Measurement of noise levels of the compared vents was carried out in a semi-anechoic chamber under the ČSN ISO 3475 standardization. To clarify increase of noise generated by the vent in an interior of an automobile, additional measurement of noise was carried out in a cabin of Porsche Cayenne 2018. From the gathered results we can conclude that under the constant flow, (of 60 square meters per hour) louder vents are those with higher pressure loss. This pressure loss is dependant primarily on the speed of the flow in the vent, as well as on the number and the adjustment of the deflectors. In a cabin of an automobile, the noise produced by the vent is negligible in comparison with total noise in an interior of a car. However, in the area surrounding the air flowing out from the vent, (approximately 0,7 meters from it) the level of acoustic pressure increases significantly.

Gurtförderanlagen werden im Bergbau und anderen Industriezweigen zum Transport von Schüttgütern eingesetzt. Der Anlagenbetrieb ist mit Geräuschemissionen verbunden. Dies kann bei Kontrolle und Wartung eine erhöhte Lärmbelastung für betroffene Mitarbeiter hervorrufen. Im Umfeld von Wohnbebauungen oder schutzbedürftigen Objekten kann die Überschreitung von Immissionsrichtwerten zu einer zeitlichen Betriebseinschränkung der hocheffizienten Anlagen führen. Zur Lärmminderung an der Quelle oder deren Nähe erfordert dies technische Schallschutzmaßnahmen. Die Tragrollen im Obertrum der Gurtförderanlagen sind bei der akustischen Wirkung von entscheidender Bedeutung. Mit einem Prüfstand für Tragrollen ist deren Schallleistung bei unterschiedlichen Geschwindigkeiten bestimmbar. Die Ergebnisse lassen Rückschlüsse auf die mechanische Belastung und die Schallemission beim Betrieb in einer Förderanlage zu. Die Arbeit benennt die Ursachen der Geräuschemissionen beim Ablauf der Rollen und stellt diese in Verbindung mit den Eigenschaften der Oberfläche und der Außermittigkeit der Drehachse dar. Die Prüfung beider Parameter basiert auf einer Rundlaufmessung. Die gewonnenen winkelabhängigen Daten erlauben eine Berechnung der Exzentrizität der Drehachse und des Verlaufs der Kreisformabweichung auf dem Rollenmantel. Daraus abgeleitete Kennwerte dienen als Vorgaben zur Anpassung und Entwicklung von Herstellungsverfahren sowie zur gezielten Auswahl geräuscharmer Tragrollen für Gurtförderanlagen. / Belt conveyor systems are used in mining operations and other industry sectors to transport bulk material. The plant operation is being linked to noise emissions. During inspections and maintenance this can cause an increased noise exposure for affected employees. In the environment of residential buildings or areas in need of protection the exceedance of immission guideline values can lead to a temporary operational limitation of these highly efficient plants. Noise abatement measures primarily at the source or in the vicinity are required to reduce noise immission. The idlers on the carrying belt side of the belt conveyor systems are of crucial importance to the acoustical properties. Their sound power level is determinable at different belt speeds with a test stand for idlers. The results allow conclusions about the mechanical stress and sound emissions during operation in a belt conveyor system. The thesis identifies the sources of noise during the roll process and places them in conjunction with the properties of the surface and the centre offset of the axis. The examination of these two parameters is based on a total indicator reading (TIR) measurement. The angle-dependent data obtained allow a calculation of the eccentricity of the axis and the curve of the circular deviation of the roller tubes. Therefrom derived characteristic values serve as specifications for the adaptation and development of manufacturing processes as well as for a careful selection of low noise idlers for belt conveyors.

Gurtförderanlagen werden im Bergbau und anderen Industriezweigen zum Transport von Schüttgütern eingesetzt. Der Anlagenbetrieb ist mit Geräuschemissionen verbunden. Dies kann bei Kontrolle und Wartung eine erhöhte Lärmbelastung für betroffene Mitarbeiter hervorrufen. Im Umfeld von Wohnbebauungen oder schutzbedürftigen Objekten kann die Überschreitung von Immissionsrichtwerten zu einer zeitlichen Betriebseinschränkung der hocheffizienten Anlagen führen. Zur Lärmminderung an der Quelle oder deren Nähe erfordert dies technische Schallschutzmaßnahmen. Die Tragrollen im Obertrum der Gurtförderanlagen sind bei der akustischen Wirkung von entscheidender Bedeutung. Mit einem Prüfstand für Tragrollen ist deren Schallleistung bei unterschiedlichen Geschwindigkeiten bestimmbar. Die Ergebnisse lassen Rückschlüsse auf die mechanische Belastung und die Schallemission beim Betrieb in einer Förderanlage zu. Die Arbeit benennt die Ursachen der Geräuschemissionen beim Ablauf der Rollen und stellt diese in Verbindung mit den Eigenschaften der Oberfläche und der Außermittigkeit der Drehachse dar. Die Prüfung beider Parameter basiert auf einer Rundlaufmessung. Die gewonnenen winkelabhängigen Daten erlauben eine Berechnung der Exzentrizität der Drehachse und des Verlaufs der Kreisformabweichung auf dem Rollenmantel. Daraus abgeleitete Kennwerte dienen als Vorgaben zur Anpassung und Entwicklung von Herstellungsverfahren sowie zur gezielten Auswahl geräuscharmer Tragrollen für Gurtförderanlagen.:1 Veranlassung und Bedeutung des Themas 2 Stand der Technik und des Wissens 3 Weiterentwicklung von Methoden zur Erfassung der Geräuschemission an Gurtförderanlagen 4 Entwicklung und Aufbau eines Prüfstandes zur Beschreibung der akustischen Eigenschaften von Tragrollen 5 Mathematische Modellierung zur Aufnahme geometrischer Rundlaufeigenschaften von Tragrollen 6 Technikums- und Feldversuche zur Validierung des mathematischen Modells und der akustischen Wirkung 7 Schlussfolgerungen zur Geräuschminderung an Förderanlagen / Belt conveyor systems are used in mining operations and other industry sectors to transport bulk material. The plant operation is being linked to noise emissions. During inspections and maintenance this can cause an increased noise exposure for affected employees. In the environment of residential buildings or areas in need of protection the exceedance of immission guideline values can lead to a temporary operational limitation of these highly efficient plants. Noise abatement measures primarily at the source or in the vicinity are required to reduce noise immission. The idlers on the carrying belt side of the belt conveyor systems are of crucial importance to the acoustical properties. Their sound power level is determinable at different belt speeds with a test stand for idlers. The results allow conclusions about the mechanical stress and sound emissions during operation in a belt conveyor system. The thesis identifies the sources of noise during the roll process and places them in conjunction with the properties of the surface and the centre offset of the axis. The examination of these two parameters is based on a total indicator reading (TIR) measurement. The angle-dependent data obtained allow a calculation of the eccentricity of the axis and the curve of the circular deviation of the roller tubes. Therefrom derived characteristic values serve as specifications for the adaptation and development of manufacturing processes as well as for a careful selection of low noise idlers for belt conveyors.:1 Veranlassung und Bedeutung des Themas 2 Stand der Technik und des Wissens 3 Weiterentwicklung von Methoden zur Erfassung der Geräuschemission an Gurtförderanlagen 4 Entwicklung und Aufbau eines Prüfstandes zur Beschreibung der akustischen Eigenschaften von Tragrollen 5 Mathematische Modellierung zur Aufnahme geometrischer Rundlaufeigenschaften von Tragrollen 6 Technikums- und Feldversuche zur Validierung des mathematischen Modells und der akustischen Wirkung 7 Schlussfolgerungen zur Geräuschminderung an Förderanlagen