Wind energy is identified a promising energy resource in Sri Lanka. Therefore, it is important to use proper technologies for efficient energy capturing in order to minimize cost of energy. Small scale wind turbines are usually installed in constricted places (particularly in urban areas) where wind flow is turbulent and difficult to predict. Savonious type vertical axis wind turbines are important due to several reasons such as good response to turbulent winds, high initial torque, low cost, low noise, less maintenance.In this study, a modified flat plate type Savonius wind rotor was proposed to cost effectively harness wind energy in constricted places. Generally, vertical axis wind turbines (VAWT) are less efficient than horizontal axis wind turbines, one reason behind this issue is wind force difference between the 2 sides of the axis is small and due to this reason torque is small and power generation capacity is less.A prototype of the proposed VAWT was fabricated and the performance was determined by acquiring experimental data. Artificial wind blow which was generated by a huge fan was used to measure rotational speed and torque characteristics at varying wind speeds. Data were collected with 1-second sampling time and a data acquisition system was developed under this study. In the proposed design one side of the turbine blades are facing the wind direction in order to capture maximum force while other side is edging the blades to have minimum opposite torque. With this concept it is expected to maximize the torque of the axis and generate more power. A sort of a passive pitch mechanism is therefore utilized in order to save energy and simplify the system. Turbine blades are simple flat plates and it eliminates usage of complex aero foils. Due to the simplicity of this design it would be possible to use this turbine for domestic electricity generation at affordable costs.Nowadays, net metering systems are being promoted in Sri Lanka and it would be beneficial to introduce low cost VAWT which operates at low winds as well as turbulent wind conditions. Based on typical household hourly load profile, viability of proposed vertical axis wind turbine was evaluated by considering rural and urban wind regimes in Sri Lanka. The costs of wind energy at two selected locations were determined in the context of net metering.

This thesis describes a conceptual design of a support frame for a synchronousgenerator used in a vertical axis wind power plant. In this system the generator isplaced on ground level. The thesis also considers the design of housing for thesupport frame and generator. The concept presented in this report is based on anearlier design. Besides geometric design, simplified simulations has been run in orderto optimize some of the parts included in the construction considering naturalfrequencies and structural strength. The result is presented as CAD-models andan assembly drawing.

Vertical axis wind turbine, developed as one of the main methods to utilize the wind energy, has a promising future; however, the major issue to limit its performance is the uneven loading on the blade during operation. Flow control mechanisms have been employed in the aerodynamic field to improve the performance of airfoils. In this study, two types of leading-edge structures, including flexible leading-edge and leading-edge roughness, are experimentally investigated to analyze their effects on altering the aerodynamic characteristics of NACA 0018 airfoil under steady flow condition and dynamic pitching condition. Current experimental results indicate that 1) during the steady flow condition, both of leading-edge structures contribute to the delay of the static stall; 2) for the dynamic pitching process, the leading-edge structures either delayed the dynamic stall angle or increased the area of the coefficient of pressure loop as a function of angle of attack.

The wind energy conversion system considered in this thesis is based on a vertical axis wind turbine with a cable wound direct drive PM generator. Diode rectifiers are used to connect several such units to a single DC-bus and a single inverter controls the power flow from the DC-bus to a utility grid. This work considers the described system from a generator perspective i.e. the turbine is primarily seen as a torque and the inverter is seen as a controlled load. A 12 kW VAWT prototype with a single turbine has been constructed within the project. The power coefficient of this turbine has been measured when the turbine is operated at various tip speed ratios. This measurement determines both how much energy the turbine can convert in a given wind and at what speed the turbine should be operated in order to maximise the energy capture. The turbine torque variation during the revolution of the turbine has also been studied. A PM generator prototype has been constructed in order to study power loss in the stator core at low electrical frequencies. Heat exchange between the stator and the air-gap between the stator and the rotor has been studied. Heat exchange between the stator and the air-gap is increased by turbulence caused by the rotor. The generator was also used in a demonstration of a DC-grid where two diode rectified PM generators supplied power to a single DC load.  An initial study of an inverter suitable for grid connection of the 12 kW PM generator has been performed. Several turbine control strategies are evaluated in simulations. The control strategies only require the parameter "turbine speed" to determine the optimal system load.

The interest in sustainable forms of energy is being driven by the anticipated scarcity of traditional fossil fuels over the coming decades. There is also a growing concern about the effects of fossil fuel emissions on human health and the environment. Many sources of renewable energy are being researched and implemented for power production. In particular, wind power generation by horizontal- and vertical-axis wind turbines is very popular. Vertical-axis wind turbines (VAWTs) have a relative construction simplicity compared to horizontal-axis wind turbines (HAWTs). However, VAWTs present specific challenges that may hinder their performance. For instance, they are strongly affected by dynamic stall. A significant part of the kinetic energy contained in the oncoming wind is lost in swirl and vortices. As a result, VAWTs have lower power production compared to HAWTs. First, the present work is aimed at the study of the aerodynamics of straight-bladed VAWTs (SB-VAWTs). Empirical calculations are conducted in a preliminary work. Then a two-dimensional double multiple streamtube (DMST) approach supported by a two-dimensional numerical study is implemented. The dynamic stall and aerodynamic performance of the rotor are investigated. A VAWT-fitted dynamic stall model is implemented. Computational fluid dynamics (CFD) simulations are conducted to serve as reference for the DMST calculations. This three-pronged approach allows us to efficiently explore multiple configurations. The dynamic stall phenomenon is identified as a primary cause of performance loss. The results in this section validate the DMST model as a good replacement for CFD analysis in early phase design provided that a good dynamic stall model is used. After having identify the primary cause of performance loss, the goal is to investigate the use to dual-element blades for alleviating the effect of dynamic stall, thereby improving the performance of the rotor. The desirable airfoil characteristics are defined and a parametric analysis conducted. In the present study the parameters consists of the size of the blade elements, the space between them, and their relative orientation. The performance of the rotor is calculated and compared to the baseline. The results highlight the preeminence of the two-element configuration over the single-element provided that the adequate parametric study is conducted beforehand. A performance enhancement is obtained over a large range of tip speed ratios. The starting characteristics and the operation stability are also improved. Finally, an economic analysis is conducted to determine the cost of energy and thus the financial viability of such a project. The Great Coast of Senegal is selected as site of operation. The energy need and sources of this region are presented along with its wind energy potential. The cost evaluation shows the economic viability by comparing the cost of energy to the current energy market prices.

In a world where money often is the main controlling factor, everything that can be tends to be more and more optimized. Regarding electrical machines, developers have always had the goal to make them better. The latest trend is to make machines as efficient as possible, which calls for accurate simulation models where different designs can be tested and evaluated. The finite element method is probably the most popular approach since it makes it possible to, in an easy and accurate way, get numerical solutions to a variety of physics problems with complex geometries and non-linear materials. This licentiate thesis includes two different projects in which finite element methods have had a central roll. In the first project, the goal was to develop a simulation model to be able to predict demagnetization of permanent magnets. It is of great importance to be able to predict if a permanent magnet will be demagnetized or not in a certain situation. In the worst case, the permanent magnets will be completely destroyed and the machine will be completely useless. However, it is more probable that the permanent magnets will not be completely destroyed and that the machine still will be functional but not as good as before. In a time where money is more important than ever, the utilization has to be as high as possible. In this study the demagnetization risk for different rotor geometries in a 12 kW direct driven permanent magnet synchronous generator was studied with a proprietary finite element method simulation model. The demagnetization study of the different rotor geometries and magnet grades showed that here is no risk for the permanent magnets in the rotor as it is designed today to be demagnetized. The project also included experimental verification of the simulation model. The simulation model was compared with experiments and the results showed good agreement. The second project treated the redesign of the rotor in the generator previously mentioned. The goal was to redesign the surface mounted NdFeB rotor to use a field concentrating design with ferrite permanent magnets instead. The motivation was that the price on NdFeB magnets has fluctuated a lot the last few years as well as to see if it was physically possible to fit a ferrite rotor in the same space as the NdFeB rotor. A new rotor design with ferrite permanent magnets was presented together with an electromagnetic and a mechanical design.

Increasing awareness of the issues of climate change and sustainable energy use has led to growing levels of interest in small-scale, decentralised power generation. Small-scale wind power has seen significant growth in the last ten years, partly due to the political support for renewable energy and the introduction of Feed In Tariffs, which pay home owners for generating their own electricity. Due to their ability to respond quickly to changing wind conditions, small-scale vertical axis wind turbines (VAWTs) have been proposed as an efficient solution for deployment in built up areas, where the wind is more gusty in nature. If VAWTs are erected in built up areas they will be inherently close to people; consequently, public acceptance of the turbines is essential. One common obstacle to the installation of wind turbines is noise annoyance, so it is important to make the VAWT rotors as quiet as possible. To date, very little work has been undertaken to investigate the sources of noise on VAWTs. The primary aim of this study was therefore to gather experimental data of the noise from various VAWT rotor configurations, for a range of operating conditions. Experimental measurements were carried out using the phased acoustic array in the closed section Markham wind tunnel at Cambridge University Engineering Department. Beamforming was used in conjunction with analysis of the measured sound spectra in order to locate and identify the noise sources on the VAWT rotors. Initial comparisons of the spectra from the model rotor and a full-scale rotor showed good qualitative agreement, suggesting that the conclusions from the experiments would be transferable to real VAWT rotors. One clear feature observed in both sets of spectra was a broadband peak around 1-2kHz, which spectral scaling methods demonstrated was due to laminar boundary layer tonal noise. Application of boundary layer trips to the inner surfaces of the blades on the model rotor was found to eliminate this noise source, and reduced the amplitude of the spectra by up to 10dB in the region of the broadband peak. This method could easily be applied to a full-scale rotor and should result in measurable noise reductions. At low tip speed ratios (TSR) the blades on a VAWT experience dynamic stall and it was found that this led to significant noise radiation from the upstream half of the rotor. As the TSR was increased the dominant source was seen to move to the downstream half of the rotor; this noise was thought to be due to the interaction of the blades in the downstream half of the rotor with the wake from the blades in the upstream half. It was suggested that blade wake interaction is the dominant noise source in the typical range of peak performance for the full-scale QR5 rotor. Different solidity rotors were investigated by using 2-, 3- and 4-bladed rotors and it was found that increasing the solidity had a similar effect to increasing the TSR. This is due to the fact that the induction factor, which governs the deflection of the flow through the rotor, is a function of both the rotor solidity and the TSR. With a large body of experimental data for validation, it was possible to investigate computational noise prediction methods. A harmonic model was developed that aimed to predict the sound radiated by periodic fluctuations in the blade loads. This model was shown to agree with similar models derived by other authors, but to make accurate predictions very high resolution input data was required. Since such high resolution blade loading data is unlikely to be available, and due to the dominance of stochastic sources, the harmonic model was not an especially useful predictive tool. However, it was used to investigate the importance of the near-field components of the sound radiated by the wind tunnel model to the acoustic array. It was shown that the near-field terms were significant over a wide range of frequencies, and the total spectrum was always greater than that of the far-field component. This implied that the noise levels measured by the acoustic array represented an upper bound on the sound radiated to the far-field, and hence that the latter would also be dominated by stochastic components. An alternative application of the harmonic model, which attempted to determine the blade loading harmonics from the harmonics in the sound field was proposed. This inversion method utilised a novel convex optimisation technique that was found to generate good solutions in the simulated test cases, even in the presence of significant random noise. The method was found to be insensitive at low frequencies, which made it ineffective for inverting the real microphone data, although this was shown to be at least partly due to the limitations imposed by the array size. In addition to the harmonic models, an empirical noise prediction method using the spectral scaling laws derived by \citet*{Brooks_1989} was trialled, and was found to be capable of making predictions that were in agreement with the measured data. The model was shown to be sensitive to the exact choice of turbulence parameters used and was also found to require good quality aerodynamic data to make accurate noise predictions. If such data were available however, it is expected that this empirical model would be able to make useful predictions of the noise radiated by a VAWT rotor.

Vertical axis wind turbines (VAWTs) have with time been outrivaled by the today common and economically feasible horizontal axis wind turbines (HAWTs). However, VAWTs have several advantages such as the possibility to put the drive train at ground level, lower noise emissions and better scaling behavior which still make them interesting for research. The work within this thesis is made in collaboration between the Department of Construction and Energy Engineering at Halmstad University and the Division for Electricity at Uppsala University. A 200 kW VAWT owned by the latter and situated close to Falkenberg in the southwest of Sweden has been the main subject of the research even if most learnings has been generalized to fit a typical vertical turbine. This particular turbine has a wooden tower which is semi-guy-wired, i.e. the tower is both firmly attached to the ground and supported by guy-wires. This thesis has two main topics both regarding VAWTs: eigenfrequency of the tower and the noise generated from the turbine. The eigenfrequency of a semi-guy-wired tower is studied and an analytical expression describing this is produced and verified by experiments and simulations. The eigenfrequency of the wire itself and how it is affected by wind load are also studied.  The noise characteristics of VAWTs have been investigated, both theoretically and by noise measurement campaigns. Both noise emission and frequency distribution of VAWTs has been studied. The work has resulted in analytical expressions for tower and wire eigenfrequency of a semi-guy-wired tower as well as recommendations for designing future towers for VAWTs. The noise emission of VAWTs has been studied and proven low compared to HAWTs. The noise frequency distribution of the 200 kW VAWT differs significantly from that of a similar size HAWTs with for example lower levels for frequencies below 3000 Hz.

Vertical axis wind turbines (VAWTs) have with time been outrivaled by the today common and economically feasible horizontal axis wind turbines (HAWTs). However, VAWTs have several advantages such as the possibility to put the drive train at ground level, lower noise emissions and better scaling behavior which still make them interesting for research. The work within this thesis is made in collaboration between the Department of Construction and Energy Engineering at Halmstad University and the Division for Electricity at Uppsala University. A 200 kW VAWT owned by the latter and situated close to Falkenberg in the southwest of Sweden has been the main subject of the research even if most learnings has been generalized to fit a typical vertical turbine. This particular turbine has a wooden tower which is semi-guy-wired, i.e. the tower is both firmly attached to the ground and supported by guy-wires. This thesis has two main topics both regarding VAWTs: eigenfrequency of the tower and the noise generated from the turbine. The eigenfrequency of a semi-guy-wired tower is studied and an analytical expression describing this is produced and verified by experiments and simulations. The eigenfrequency of the wire itself and how it is affected by wind load are also studied.  The noise characteristics of VAWTs have been investigated, both theoretically and by noise measurement campaigns. Both noise emission and frequency distribution of VAWTs has been studied. The work has resulted in analytical expressions for tower and wire eigenfrequency of a semi-guy-wired tower as well as recommendations for designing future towers for VAWTs. The noise emission of VAWTs has been studied and proven low compared to HAWTs. The noise frequency distribution of the 200 kW VAWT differs significantly from that of a similar size HAWTs with for example lower levels for frequencies below 3000 Hz.

The growing global demand for clean energy is critical, and wind power plays a crucial role in addressing this need. The increasing demand is driving advancements in the field of offshore wind power and one promising innovation is the counter-rotating vertical axis turbines (CRVT), specifically designed for floating wind power installations. The aim of this project was to develop a dynamic simulation and 3D visualization of a floating wind turbine using CRVT technology. In this project, simplified force models were created with the aim to incorporate more complex models from experts in wind and water dynamics in the future. The simplified force calculations included gravity, buoyancy, the Morison equation, as well as forces from a simple mooring and a generator. The implemented aerodynamic forces were obtained from a complex model developed by an expert in aerodynamics. The simulation was conducted in Matlab, utilizing first-principal physics for dynamics calculations. All the measurements used to compute the geometry of the wind turbine were imported from a CSV file. Finally, the RK4 method was employed to compute the steps, and a Maya model was created for the visualization of the wind turbine. In conclusion, the simulation successfully enabled the wind turbine's motion in all six degrees of freedom and provided a visual representation of the results. However, significant approximations were made, and additional validation is necessary to ensure the accuracy of the simulation.