Introduction 76Br is of interest for in vivo PET imaging applications. Its relatively long half-life (16.1 h) allows use not only on small molecules but also proteins which have slow excretion as carrier molecules. Irradiation using a low energy proton beam (~ 20 MeV) on an enriched Cu276Se target, followed by dry distillation with thermal chromatography, is one of the best methods to obtain sufficient amounts of 76Br for clinical applications1,2. However, the thermal chromatography is plagued by poor reproducibility and appears unsuitable for automation of its production, leading us to remove the thermal chroma-tography from the dry distillation. In this investigation we employed H2O solution to collect 76Br and optimized the distillation condition using a small amount of 77Br (57.0 h). We also produced large amount of 76Br under the optimized conditions to evaluate the dry distillation method. Material and Methods Target preparation and dry distillation were conducted based on the methods described in previous reports1,2. To produce 77Br, Cu2natSe target was irradiated with 20 MeV proton beams (5 µA) accelerated by AVF cyclotron in the Japan Atomic Energy Agency. The following two systems were used in the dry distillation optimization studies; (1) an initial system was composed of two furnaces, a main and an auxiliary furnace. Temperature of each furnace was set at 1050 °C (main) and 200 °C (auxiliary) respectively; (2) the second system was made of one large furnace composed of heating and cooling area. Temperature of the heating area was varied from 1050 to 1120 °C. In both systems PTFE tubing, leading to a H2O solution (15 mL), was inserted into the apparatus. The irradiated target was heated under streaming Ar gas (30 mL/min.). An enriched Cu276Se target (76Se enrichment: 99.67%) was used for 76Br production. Radioactivity was measured on a high-purity germanium (HPGe) detector coupled to a multichannel analyzer. TLC analyses were conducted on Al2O3 plates (Merck) using 7:1 acetone:H2O as the eluting solvent. Results and Conclusion Low efficiency (33 %) of 77Br recovery was ob-served in the initial system. Distribution of radioactivity inside the apparatus showed that 35 % was trapped in the PTFE tube and the quartz tube. The recovery yield was increased up to 54 % when the auxiliary furnace was turned off, indicating that the temperature gradient inside the quartz tube is suitable to carry 77Br effectively to the H2O trap. We initially used a quartz boat to place the irradiated target in the furnace, but found that using a reusable tungsten backing was better. However, we found that recovery yield was dramatically reduced to 18 %. The studies where the temperature was varied showed that releasing efficiency was increased up to 100 % at the temperature of 1120 °C. Good recovery yield (~ 77 %) was achieved after optimizing the temperature gradient (FIG. 1b). Using the optimized setup, 76Br production runs (n = 6) have been conducted, allowing us to recover up to 39.8 MBq/µAh (EOB) of 76Br. High specific activity (~4400 GBq/µmol) was obtained in the final solution. TLC analysis showed that chemical form obtained was bromide. We concluded that the dry distillation using H2O trap is capable of providing enough high purity 76Br for clinical applications.

Introduction Monte-Carlo simulations can be used to assess isotope production on small medical cyclotrons. These simulations calculate the particle interactions with electric and magnetic fields, as well as the nuclear reactions. The results can be used to predict both yields and isotopic contaminations and can aid in the optimum design of target material and target geometry [1,2]. FLUKA is a general-purpose tool widely used in many applications from accelerator shielding to target design, calorimetry, activation, dosimetry, detector design, neutrino physics, or radiotherapy [3,4]. In this work, we applied the Monte-Carlo code FLUKA to determine the accuracy of predicting yields of various isotopes as compared to experimental yields. Material and Methods The proton beam collimation system, as well as the liquid and solid target of the TR13 cyclotron at TRIUMF, has been modeled in FLUKA. The proton beam parameters were initially taken from the cyclotron design specifications and were optimized against experimental measurements from the TR13. Data from irradiations of different targets and with different beam currents were collected in order to account for average behavior, see FIG. 1. Yields for a pencil proton beam as well as a beam spread out in direction and energy have been calculated and have been compared to experimental results obtained with the TR13. Results and Conclusion The reactions listed in TABLE 1 were assessed. For most reactions a good agreement was found in the comparison between experimental and simulated saturation yield. TABLE 1 only shows the yields simulated with a proton beam with a spread in both direction and energy. In most cases, the simulated yield is slightly larger or comparable. Only the calculated yield for 55Co was significantly lower by a factor of 4.2. This is still a good agreement considering that FLUKA was originally a high-energy physics code. It may indicate that the FLUKA internal cross-section calculation for this isotope production needs some optimization. In summary, we conclude that FLUKA can be used as a tool for the prediction of isotope production as well as for target design.

Introduction The TR-24 is relatively new to the cyclotron market and its advantages over lower energy PET cyclotrons have not yet been fully realized. A new high current [18F] fluoride production target that takes advantage of the higher energy and current afforded by the TR-24 has been developed. Material and Methods The TR-24 cyclotron presents challenges of producing conventional PET isotopes even with its variable energy capability (18–25 MeV). Simultaneous irradiation of two targets that require different proton energies is possible only using beam energy degrader. Due to the relatively wide energy window, the degrader design is not trivial, especially for the high current operation. For example, reduction of beam energy from 24 to 18 MeV would require the use of an approximately 1.5 mm thick aluminum degrader. At 100 μA this degrader would have to be capable of dissipating 700 W of beam power, which would be challenging to achieve with no cooling or using a conventional helium cooling window. However, cooling water used as a beam energy degrader can dissipate several kilowatts of beam energy and provide additional cooling for target material and window foils. FIGURE 1 demonstrates the concept of the water cooled target window. A standard 18F- water target with a 2.5 mL fill volume and a 30 degree beam incident angle was modified to accept the new water window. A 1 mm thick region of circulating cooling water was inserted between the vacuum and the product foil. The combined beam energy degradation caused by the vacuum foil (0.00012“ Havar), the cooling water (1 mm) and the target foil (0.00012“ Havar) was approximately 7 MeV for a 24 MeV incident proton energy. The target was installed on a target selector mounted directly on the TR-24 cyclotron. No additional beam focusing or steering devices were used to defocus or correct beam shape. A small recirculation water system was setup to supply cooling water for the degrader. A mixed bed ion exchange column was installed on the return line to trap N-13 and radioactive metal ions that could possibly be etched from the Havar foils. The water in the degrader was continually circulated in a closed loop providing cooling to the vacuum and target foils. An 800mL/min water flow through the degrader was generated by a low pressure water pump. Results Several tests were performed with O-16 water to establish current – pressure curve and to determine “burn through” current (FIGURE 2). Conclusion Initial tests demonstrated that the new F-18 target with a 1 mm water degrader is capable of accepting power levels in excess of 3.6 kW, operating at 150 μA. More testing is under way, including testing with H218O to determine the F-18 production capacity of this target. We will look into adapting this concept to all ACSI PET targets, including the high current F-18 produc-tion target which can potentially reach an operational current of 200 μA.

Introduction The established methods for the production of 99Mo, based on fission in nuclear reactors, continue to present problems as a result of the plant’s aging and the significant investments needed for maintenance or for their renewal. Much research work is thus in progress on the study of alternative methods for the production of 99mTc in quantities and with the degree of purity required for the clinical use. Between them, the cyclotron production of 99mTc via the 100Mo(p,2n)99mTc reaction has turned out as the most attractive alternative. One critical aspect regarding the production of 99mTc with cyclotron is the need for a robust and reliable target production process. Several techniques have been indicated as extremely promising such has plasma spray and laser cladding; however these methods require specialized instrumentation and complex operations to be performed handling activated materials in order to recover irradiated Mo. In this work we report the development of the work done at the University of Bologna, as a part of a wider INFN project, as regards the methods of preparation of solid targets suitable for the production of 99mTc irradiating a target of 100Mo, employing a cyclotron for biomedical use, normally operated for the production of PET radionuclides. Material and Methods Irradiations were performed with a 16.5 MeV GE PETtrace cyclotron equipped with a solid target station previously developed by our group (1). In initial tests, a stack of 1–3 metallic foils, 100 μm thick, of natMo were irradiated with protons in the 15.9→9.8 MeV energy range. Foils were then dissolved in a HNO3-HCl solution and samples were analyzed with high resolution gamma-ray spectrometry (Canberra, including a HPGe detector with a 30% relative efficiency and a resolution of 1.8 keV at 1332 keV) using Genie2000 software; the measurement campaign lasted several weeks to take into account the different half-lives of the produced radionuclides. Results were extrapolated to a highly enriched 100Mo target and compared to Monte Carlo simulations previously performed with FLUKA and TALYS codes (2). In order to investigate a method of preparation of the target that would make easier the recovery of the enriched material and recycling for the preparation of a new target, it was subsequently studied the preparation of pellets of Molybdenum trioxide. MoO3 powder (Sigma Aldrich, 99.9% trace metals basis, particle size < 150 μm) was used to prepare pellets using a 10 ton press. Pellets obtained in this way were then sintered on a Platinum support using a CARBOLITE furnace under a controlled atmosphere; the temperature was ramped according to a controlled and reproducible temperature cycle. Sintered pellets were subjected to visual inspection, mechanical tests of resistance to loading and downloading in the cyclotron target station, thermal tests and then irradiated at increasing current. The irradiated targets were again visually inspected then weighed, dissolved and subjected to gamma-ray spectrometry analysis. Results and Conclusion The experimental saturation yield for 99mTc calculated on the basis of the gamma-ray analysis of irradiated metal foils, gave an extrapolated yield of 1.115 ± 0.015 GBq/μA for a 100 μm thick 100Mo enriched target, in accordance with the value of 1.107 ± 0.002 GBq/μA obtained in Monte Carlo simulations. On these bases, an irradiation of 3 h at 50 μA is expected to produce 16.3 ± 0.2 GBq of 99mTc; considering the use of an efficient purification system, a radionuclidic purity > 99.9 % 2 h after the EndOfBombardment and a specific activity comparable with the actual standards are expected as achievable. Experiments on sintering pellets are still on going at the time of writing this report; initial results showed that addition of proper aggregating materials allows for suitable pellets preparation. The sintering process allows to obtain pellets having sufficient mechanical strength to withstand loading and downloading operations. Initial irradiation tests with beam current up to 25 μA were performed successfully with no changes in mass and mechanical properties of the pellet. These encouraging results suggest that sintered pellets may be a relatively inexpensive and easy solution to prepare 100Mo targets for the cyclotron production of 99mTc. Further experimental tests at higher beam current will be performed in order to assess the maximum current achievable with no damage of the target. At the same time, a prototype automated module based on standard industrial components is in testing phase as regards performance in the separation and purification processes.

Background: As a tactic of combating money laundering, auditors have been introduced asguardians and enforcers of the laws, due to their insight into company affairs. However, as shownby the Finance Police, it is rare that auditors report suspicions on money-laundering activities.That is, despite the obligations imposed on the profession, their share of total number or reportfiles each year a very small fraction. Aim: When investigating the infrequent reporting by auditors, it all boils down to a seemingexpectation gap. As such, the aim of this study has been to test that hypothesis, by conducting anattitude survey among Swedish auditors, as we believe the attitude towards the obligations tohave an impact on the tendency to report. Method: The perception of auditors on their role in combating money laundering and thehypothesized expectation gap between the audit profession and the state in its legislative capacitywas explore through the use of a questionnaire sent to 68 authorized or approved auditors withinthree different categories of firms; big-four firms, second tier firms and small local firms inStockholm and Uppsala. Conclusion: We cannot with certainty draw conclusion on whether the auditors’ perceivethemselves as having an obvious preventive role in the fight money laundering due to ambiguousanswers, but there seem to exist a somewhat opposed attitude toward the suggested duty to detectmoney laundering during audits. Nevertheless, traces of an expectation gap were found in thisstudy. However, with a sample size of 20 respondents, we cannot make generalizations withoutcareful consideration. As such, the findings of this study should be regarded as indicative ratherthan definitive.

Mapping stationary objects and tracking moving targets are essential for many autonomous functions in vehicles. In order to compute the map and track estimates, sensor measurements from radar, laser and camera are used together with the standard proprioceptive sensors present in a car. By fusing information from different types of sensors, the accuracy and robustness of the estimates can be increased. Different types of maps are discussed and compared in the thesis. In particular, road maps make use of the fact that roads are highly structured, which allows relatively simple and powerful models to be employed. It is shown how the information of the lane markings, obtained by a front looking camera, can be fused with inertial measurement of the vehicle motion and radar measurements of vehicles ahead to compute a more accurate and robust road geometry estimate. Further, it is shown how radar measurements of stationary targets can be used to estimate the road edges, modeled as polynomials and tracked as extended targets. Recent advances in the field of multiple target tracking lead to the use of finite set statistics (FISST) in a set theoretic approach, where the targets and the measurements are treated as random finite sets (RFS). The first order moment of a RFS is called probability hypothesis density (PHD), and it is propagated in time with a PHD filter. In this thesis, the PHD filter is applied to radar data for constructing a parsimonious representation of the map of the stationary objects around the vehicle. Two original contributions, which exploit the inherent structure in the map, are proposed. A data clustering algorithm is suggested to structure the description of the prior and considerably improving the update in the PHD filter. Improvements in the merging step further simplify the map representation. When it comes to tracking moving targets, the focus of this thesis is on extended targets, i.e., targets which potentially may give rise to more than one measurement per time step. An implementation of the PHD filter, which was proposed to handle data obtained from extended targets, is presented. An approximation is proposed in order to limit the number of hypotheses. Further, a framework to track the size and shape of a target is introduced. The method is based on measurement generating points on the surface of the target, which are modeled by an RFS. Finally, an efficient and novel Bayesian method is proposed for approximating the tire radii of a vehicle based on particle filters and the marginalization concept. This is done under the assumption that a change in the tire radius is caused by a change in tire pressure, thus obtaining an indirect tire pressure monitoring system. The approaches presented in this thesis have all been evaluated on real data from both freeways and rural roads in Sweden. / SEFS -- IVSS / VR - ETT

Thesis (M.S.)--University of Texas at El Paso, 2007. / Title from title screen. Vita. CD-ROM. Includes bibliographical references. Also available online.

Thesis (MScIng)--University of Stellenbosch, 2006. / Bibliography. Also available via the Internet.

Made available in DSpace on 2014-10-09T12:43:17Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:58:18Z (GMT). No. of bitstreams: 1 06443.pdf: 4052789 bytes, checksum: ad0a002c9a73bb765e639e0bde37d570 (MD5) / Dissertacao (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

No description available.