Much study has been carried out to determine the properties of Lamellar Graphite Iron (LGI) or grey iron and their relations to factors such as the cooling rate, the dendrite morphology, the pouring temperature, and so on. However, there hasn’t been much comprehensive study on the properties of LGI outside the generally used and accepted composition, with 1 to 3% Silicon. The scope of this study is to measure and evaluate the thermal conductivity and tensile strength of LGI, for a higher concentration of  Si and different carbon contents. The concentration of Si aimed for was 4% but the concentration obtained after spectroscopy was between 4.1% to 4.15%. There are two hypereutectic, one near-eutectic and three hypoeutectic samples considered and these six chemical compositions were cast under different cooling conditions . The cooling time has been varied by providing different molds of 30mm, 55mm, and 80mm diameter cylinders respectively, for all the six sample compositions. The microstructure analysis carried out studies the segregation of Si, the graphite morphology, primary austenite morphology. These factors are then compared to the thermal and tensile behavior measured in this study. It can be observed that the thermal conductivity studied in the present work has a direct correlation for a higher Si content and tends to be greater than the thermal conductivity values observed from other studies with lower content Of Si. However, the conductivity shows an inverse relation with the cooling rate and is maximum for the samples with the lowest cooling rate. The tensile strength, on the other hand, seems to have a lower value than that observed in previous studies for LGI with 1 to 3% Si, but shows a direct correlation with the cooling rate. The mean area fraction of dendrites obtained and the mean interdendritic hydraulic diameter is also measured and their influence on the properties are also studied. The addition of more Si has greatly favored the thermal behavior positively but has also reduced the tensile strength.

La thermographie infrarouge est une méthode largement employée pour la caractérisation des propriétés thermophysiques des matériaux. L’avènement des diodes laser pratiques, peu onéreuses et aux multiples caractéristiques, étendent les possibilités métrologiques des caméras infrarouges et mettent à disposition un ensemble de nouveaux outils puissants pour la caractérisation thermique et le contrôle non desturctif. Cependant, un lot de nouvelles difficultés doit être surmonté, comme le traitement d’une grande quantité de données bruitées et la faible sensibilité de ces données aux paramètres recherchés. Cela oblige de revisiter les méthodes de traitement du signal existantes, d’adopter de nouveaux outils mathématiques sophistiqués pour la compression de données et le traitement d’informations pertinentes. Les nouvelles stratégies consistent à utiliser des transformations orthogonales du signal comme outils de compression préalable de données, de réduction et maîtrise du bruit de mesure. L’analyse de sensibilité, basée sur l’étude locale des corrélations entre les dérivées partielles du signal expérimental, complète ces nouvelles approches. L'analogie avec la théorie dans l'espace de Fourier a permis d'apporter de nouveaux éléments de réponse pour mieux cerner la «physique» des approches modales.La réponse au point source impulsionnel a été revisitée de manière numérique et expérimentale. En utilisant la séparabilité des champs de température nous avons proposé une nouvelle méthode d'inversion basée sur une double décomposition en valeurs singulières du signal expérimental. Cette méthode par rapport aux précédentes, permet de tenir compte de la diffusion bi ou tridimensionnelle et offre ainsi une meilleure exploitation du contenu spatial des images infrarouges. Des exemples numériques et expérimentaux nous ont permis de valider dans une première approche cette nouvelle méthode d'estimation pour la caractérisation de diffusivités thermiques longitudinales. Des applications dans le domaine du contrôle non destructif des matériaux sont également proposées. Une ancienne problématique qui consiste à retrouver les champs de température initiaux à partir de données bruitées a été abordée sous un nouveau jour. La nécessité de connaitre les diffusivités thermiques du matériau orthotrope et la prise en compte des transferts souvent tridimensionnels sont complexes à gérer. L'application de la double décomposition en valeurs singulières a permis d'obtenir des résultats intéressants compte tenu de la simplicité de la méthode. En effet, les méthodes modales sont basées sur des approches statistiques de traitement d'une grande quantité de données, censément plus robustes quant au bruit de mesure, comme cela a pu être observé. / Infrared thermography is a widely used method for characterization of thermophysical properties of materials. The advent of the laser diodes, which are handy, inexpensive, with a broad spectrum of characteristics, extend metrological possibilities of infrared cameras and provide a combination of new powerful tools for thermal characterization and non destructive evaluation. However, this new dynamic has also brought numerous difficulties that must be overcome, such as high volume noisy data processing and low sensitivity to estimated parameters of such data. This requires revisiting the existing methods of signal processing, adopting new sophisticated mathematical tools for data compression and processing of relevant information.New strategies consist in using orthogonal transforms of the signal as a prior data compression tools, which allow noise reduction and control over it. Correlation analysis, based on the local cerrelation study between partial derivatives of the experimental signal, completes these new strategies. A theoretical analogy in Fourier space has been performed in order to better understand the «physical» meaning of modal approaches.The response to the instantaneous point source of heat, has been revisited both numerically and experimentally. By using separable temperature fields, a new inversion technique based on a double singular value decomposition of experimental signal has been introduced. In comparison with previous methods, it takes into account two or three-dimensional heat diffusion and therefore offers a better exploitation of the spatial content of infrared images. Numerical and experimental examples have allowed us to validate in the first approach our new estimation method of longitudinal thermal diffusivities. Non destructive testing applications based on the new technique have also been introduced.An old issue, which consists in determining the initial temperature field from noisy data, has been approached in a new light. The necessity to know the thermal diffusivities of an orthotropic medium and the need to take into account often three-dimensional heat transfer, are complicated issues. The implementation of the double singular value decomposition allowed us to achieve interesting results according to its ease of use. Indeed, modal approaches are statistical methods based on high volume data processing, supposedly robust as to the measurement noise.