In this article, we report an attempt of extending the InGaAsN materials towards 1.3µm and 1.55µm wavelength. All these InGaAsN samples are grown in a plasma-assisted solid-source molecular-beam epitaxy (SS-MBE) system. Our experiments revealed that the nitrides could be grown with both direct nitrogen beam and dispersive nitrogen. The nitrogen incorporation rate could be reduced by the presence of indium flux. The interaction between nitrogen and indium might lead to 3D growth mode and growth dynamics. It is proved that the increasing growth rate reduces the nitrogen incorporation efficiency. The data for nitrogen sticking coefficient are somewhat contradictive. The growth with dispersive nitrogen source causes the improvement of material quality. Fixed indium flux is a better way for the wavelength control. Also, we report some growth optimization work for better PL property and the annealing effect on the samples. Literature is sometimes reviewed for comparison. / Singapore-MIT Alliance (SMA)

Electron transport and relaxation may be substantially different in low-dimensional systems compared to that observed in bulk material. In the present work, Monte Carlo models are used for the solution to the Boltzmann transport equation, with scattering rates calculated quantum mechanically for superlattice and quantum wells. Carrier relaxation following optical excitation is examined in multiple quantum well systems. Simulated results of the carrier relaxation process in coupled asymmetric wells and modulation doped wells are in good agreement with published experimental results on similar structures. Scattering rates in superlattices due to polar optical phonons, intervalley phonons, ionized impurities and carrier-carrier scattering are derived. Carrier transport through high energy superlattice minibands is examined in superlattice base hot electron transistors. Additionally, transport in the ballistic limit in periodic quantum wire structures, including geometric superlattices, is examined utilizing a mode matching method. / Graduation date: 1992

This dissertation explores the development of commercial entertainments and film exhibition in the urban South around the turn of the last century through the growth and decline of Jake Wells Enterprises. A former professional baseball player, Wells invested in a wide variety of public amusements, with the core of his early business centered on establishing and organizing a string of vaudeville, popularly priced, and legitimate theaters throughout the largest cities in the region, a network he later transitioned to showing exclusively motion pictures. A thorough analysis of period newspapers, trade journals, and some business records covering Wells’ career provides much-needed evidence for film and cultural historians wishing to understand the genesis and evolution of public amusements in the region, and its negotiation of traditional social and cultural institutions. In the 1890s, Wells played and managed several professional baseball teams in the South. The sport educated players and spectators alike to both the values and creed of New South progress, and to rising tensions confronting the intersection of modern and traditional forms of culture. Using his experiences and contacts gained in baseball, Wells helped foster a culture of entrepreneurship and innovation required for the progress of media industries in the region, establishing social networks of knowledge and improving distribution flows of entertainment. The dissertation explores how race and the genteel emerged as regional characteristics most influential to the success of this conversion in many urban areas. Protestants and evangelical culture served as the bulkhead supporting opposition to new amusements. Wells’ expansion plans and violations of Sabbath day laws evoked a “spatial” battle between commercialism and religion where political, social, and cultural power drawn from place and identity were challenged and reconfigured. Another chapter explores the exhibition and reception of early Civil War films in the region. Wells and other exhibitors were influential in their production and circulation nationwide, and positioned cinema as an alternative shrine to commemorate the Lost Cause in many communities. The last chapter shows how Wells failed to meet local demands and consumer desires in competition with the rise of national chain theaters and Hollywood’s vertical integration.

This thesis analyzes H. G. Wells’s The Island of Doctor Moreau and Joseph Conrad’s Heart of Darkness within the context of nineteenth-century evolutionary theory. I explore how Charles Darwin and Thomas Huxley used evolution by natural selection to develop differing explanations of the origins of ethics and how this impacted the place each scientist gave morality in civilization. By exploring how Huxley and Darwin understood morality to derive from the phenomena of sympathy and restrain, I illustrate how Wells’s and Conrad’s novellas interrogate these discourses of altruism.

Fractured reservoirs have been traditionally idealized using dual-porosity models. In these models, all matrix and fractures systems have identical properties. However, it is not uncommon for naturally fractured reservoirs to have orthogonal fractures with different properties. In addition, for hydraulically fractured reservoirs that have preexisting natural fractures such as shale gas reservoirs, it is almost certain that these types of fractures are present. Therefore, a triple-porosity (dual-fracture) model is developed in this work for characterizing fractured reservoirs with different fractures properties. The model consists of three contiguous porous media: the matrix, less permeable micro-fractures and more permeable macro-fractures. Only the macro-fractures produce to the well while they are fed by the micro-fractures only. Consequently, the matrix feeds the micro-fractures only. Therefore, the flow is sequential from one medium to the other. Four sub-models are derived based on the interporosity flow assumption between adjacent media, i.e., pseudosteady state or transient flow assumption. These are fully transient flow model (Model 1), fully pseudosteady state flow model (Model 4) and two mixed flow models (Model 2 and 3). The solutions were mainly derived for linear flow which makes this model the first triple-porosity model for linear reservoirs. In addition, the Laplace domain solutions are also new and have not been presented in the literature before in this form. Model 1 is used to analyze fractured shale gas horizontal wells. Non-linear regression using least absolute value method is used to match field data, mainly gas rate. Once a match is achieved, the well model is completely described. Consequently, original gas in place (OGIP) can be estimated and well future performance can be forecasted.

Hydraulic fracturing has recently been the completion of choice for most tight gas bearing formations. It has proven successful to produce these formations in a commercial manner. However, some considerations have to be taken into account to design an optimum stimulation treatment that leads to the maximum possible productivity. These considerations include, but not limited to, non-Darcy flow and multiphase flow effects inside the fracture. These effects reduce the fracture conductivity significantly. Failing to account for that results in overestimating the deliverability of the well and, consequently, to designing a fracture treatment that is not optimum. In this work a thorough investigation of non-Darcy flow and multi-phase flow effects on the productivity of hydraulically fractured wells is conducted and an optimum fracture design is proposed for a tight gas formation in south Texas using the Unified Fracture Design (UFD) Technique to compensate for the mentioned effects by calculating the effective fracture permeability in an iterative way. Incorporating non-Darcy effects results in an optimum fracture that is shorter and wider than the fracture when only Darcy calculations are considered. That leads to a loss of production of 5, 18 percent due to dry and multiphase non-Darcy flow effects respectively. A comparison between the UFD and 3D simulators is also done to point out the differences in terms of methodology and results. Since UFD incorporated the maximum dimensionless productivity index in the fracture dimensions design, unlike 3D simulators, it can be concluded that using UFD to design the fracture treatment and then use the most important fracture parameters outputs (half length and CfDopt) as inputs in the simulators is a recommended approach.

One of the issues with multilateral wells is determining the contribution of each lateral to the total production that is measured at the surface. Also, if water is detected at the surface or if the multilateral well performance declines, then it is difficult to identify which lateral or laterals are causing the production decline. One way to estimate the contribution from each lateral is to run production Logging Tools (PLT). Unfortunately, PLT jobs are expensive, time-consuming, labor-intensive and involve operational risks. An alternative way to measure the production from each lateral is to use Distributed Temperature Sensing (DTS) technology. Recent advances in DTS technology enable measuring the temperature profile in horizontal wells with high precision and resolution. The changes in the temperature profile are successfully used to calculate the production profile in horizontal wells. In this research, we develop a computer program that uses a multilateral well model to calculate the pressure and temperature profile in the motherbore. The results help understand the temperature and pressure behaviors in multilateral wells that are crucial in designing and optimizing DTS installations. Also, this model can be coupled with an inversion model that can use the measured temperature and pressure profile to calculate the production from each lateral. Our model shows that changing the permeability or the water cut produced from one lateral results in a clear signature in the motherbore temperature profile that can be measured with DTS technology. However, varying the length of one of the lateral did not seem to impact the temperature profile in the motherbore. For future work, this research recommends developing a numerical reservoir model that would enable studying the effect of lateral inference and reservoir heterogeneity. Also recommended is developing an inversion model that can be used to validate our model using field data.

We haved studied the magneto-transport properties of two dimensional electron gas (2DEG) in Si £_-doped In0.22Ga0.78As/AlGaAs single quantum wells ( QWs ) by using Shubnikov-de Haas ( SdH ) measurements . From the SdH measurement , we can clearly observe the SdH oscillations and obtain the SdH frequencies. It indicates the 2DEG in these QWs was confirmed . We also obtain the deep level binding energies¡G 104.4 meV and 9.6 meV for sample 1 and 50.2meV for sample2 by T-dependent Van der Pauw Hall effect measure- ment at magnetic field 0.3T. The difference of these two samples was the In0.1Ga0.9As layer of sample 2 was inserted between In0.22Ga0.78As well and the GaAs spacers . So in this paper , we tried to propose a model to interpret the deep-level traps in the QWs and studied the effect of In0.1Ga0.9As inserted-layer on the In0.22Ga0.78As/GaAs Single Quantum Wells.

<p>Long-wavelength (1.3-μm) vertical-cavity surface-emitting lasers (VCSELs) are of great interest as low-cost, high performance light sources for fiber-optic metro and access networks. During recent years the main development effort in this field has been directed towards all epitaxial GaAs-based structures by employing novel active materials. Different active region candidates for GaAs-based 1.3-μm VCSELs such as GaInNAs/GaAs QWs, GaAsSb QWs or InAs/InGaAs QDs have been investigated. However, the difficult growth and materials properties of these systems have so far hampered any real deployment of the technology. More recently, a new variety of VCSELs have been developed at KTH as based on highly strained InGaAs QWs and negative gain cavity detuning to reach the 1.3-μm wavelength window. The great benefit of this approach is that it is fully compatible with standard materials and processing methods.</p><p>The aim of this thesis is to investigate long-wavelength (1.3-μm) VCSELs using ~1.2-μm In0.4GaAs/GaAs Multiple Quantum Wells (MQWs). A series of QW structures, DBR structures and laser structures, including VCSELs and Broad Area lasers (BALs) were grown by metal-organic vapor phase epitaxy (MOVPE) and characterized by various techniques: Photoluminescence (PL), high-resolution x-ray diffraction (XRD), atomic force microscopy (AFM), high accuracy reflectance measurements as well as static and dynamic device characterization. The work can be divided into three parts. The first part is dedicated to the optimization and characterization of InGaAs/GaAs QWs growth for long wavelength and strong luminescence. A strong sensitivity to the detailed growth conditions, such as V/III ratio and substrate misorientation is noted. Dislocations in highly strained InGaAs QW structure and Sb as surfactant assisted in InGaAs QW growth are also discussed here. The second part is related to the AlGaAs/GaAs DBR structures. It is shown that the InGaAs VCSELs with doped bottom DBRs have significantly lower slope efficiency, output power and higher threshold current. By a direct study of buried AlGaAs/GaAs interfaces, this is suggested to be due to doping-enhanced Al-Ga hetero-interdiffusion. In the third part, singlemode, high-performance 1.3-μm VCSELs based on highly strained InGaAs QWs are demonstrated. Temperature stable singlemode performance, including mW-range output power and 10 Gbps data transmission, is obtained by an inverted surface relief technique.</p>

Thesis (Ph. D.)--University of Washington, 2000. / Vita. Includes bibliographical references (p. 97-104).