Engineers proposed the idea that arching action present may be present in bridge deck cantilever slab overhangs, stiffened along their longitudinal free edge via a traffic barrier, subjected to a wheel load. The experimental research program consisted of the design, construction, and static as well as fatigue destructive testing of a full-scale innovative bridge deck slab complete with two traffic barrier walls. The observed experimental data provided extremely interesting findings that indicated a very strong presence of arching action in edge-stiffened cantilever slab overhangs subjected to static and fatigue wheel loads. Deflection profiles indicated curvatures that contradict classical flexural behavior. Large tensile strain magnitudes on the bottom reinforcing mat in all cantilever test locations as well as cracking patterns dictate behavior typical to arching action. Top transverse strains measured did not agree with flexural theory and patterns confirmed earlier research finding that the quantity of top transverse reinforcement may be reduced. Compressive strains measured on the top surface of the cantilever contradicted flexural theory and confirmed the presence of arching action. Punching shear modes of failure observed in all test locations also strengthened the argument for the presence of arching action. Theoretical and analytical modeling techniques were able to validate and confirm the experimental test results. Based on experimental research findings and analytical modeling researchers were able to confirm a major presence of arching action in edge-stiffened cantilever slab overhangs subjected to static and fatigue wheel loads. Recommendations include a proposed reduction in top transverse reinforcement provided in the adjacent internal panel due to the presence arching action that could contribute to a significant initial capital cost savings. Based on the research findings, the report also suggests potential provisions to design codes that take into account the presence of arching action. Further research and theoretical modeling is still required to better understand the presence of arching action in edge-stiffened cantilever slab overhangs. Additional testing and a demonstration project complete with civionics and structural health monitoring will aid engineers in the implementation of the break-through findings highlighted in this study. / February 2016

The main goal of this research is to develop new and innovative designs for insulated rail joints for improved life cycle and higher cost effectiveness. The research focuses on using electrically insulating materials that replace the epoxy used in current bonded insulated joints. Insulated joints (commonly known as "IJ") are widely used on railways to electrically insulate rail segments from each other, while mechanically connecting them together. The electrical insulation is necessary for accommodating track signals. The mechanical strength is needed to ensure the rail and IJs are able to withstand the vertical, longitudinal, and lateral forces that commonly occur on track. Insulating materials that can replace the epoxy used in bonded insulated joints are researched. The electrical insulation properties and mechanical strength of different materials are examined to determine the suitability of different materials for use in insulated joint. The most promising materials for use are determined to be fiber reinforced polymers and ceramics. Insulated joint designs are developed to accentuate the strengths of these two materials. The Insulating Metal Composite (IMC) insulated joint design that uses ceramics is determined to be the most promising of the new designs and is pursued through prototype fabrication. This particular joint design is analyzed structurally using both closed form analysis and FEA analysis using the software package ABAQUS. Electrical analysis using PSPICE is carried out on the joint. Prototypes of several design iterations of the insulating metal composites are built and tested. A proof of concept static bending test of the insulating metal composites used to build the IMC insulated joint is performed using a Tinius Olsen compressive tester. A rolling-wheel load test is performed on a prototype IMC component installed in rail. Finally, a prototype of a complete IMC insulated joint is fabricated and installed on the FAST test track at TTCI facility in Pueblo, Colorado for field evaluation. Electrical testing using a megohmmeter is performed on a complete prototype joint. Structural analysis shows that the components used to construct the IMC insulated joint can withstand the vertical and longitudinal loads applied to them. Electrical analysis shows that the joint can provide adequate electrical insulation and provides the required dielectric strength in the AREMA Manual for Railway Engineering. The proof of concept test shows that an IMC component can withstand 100 kips of static load without damage. The rolling-wheel load test shows that the ceramic in the IMC components can withstand a large shock load and that the rail used in the IMC insulated joints can survive repeated and shock loads. The testing of the prototype joint on the FAST track, which is ongoing at this time has shown that the new joint concept is fully capable of providing adequate electrical insulation and mechanical strength throughout the expected life of IJs. / Master of Science

A group of researchers, engineers, and government transportation officials have teamed up to design two bridges with simply-supported FRP composite structural beams. The Toms Creek Bridge, located in Blacksburg, Virginia, has been in service for six years. Meanwhile, the Route 601 Bridge, located in Sugar Grove, Virginia, has been in service for two years. Researchers have conducted load tests at both bridges to determine if their performance has changed during their respective service lives. The key design parameters under consideration are: deflection, wheel load distribution, and dynamic load allowance. The results from the latest tests in 2003 yield little, yet statistically significant, changes in these key factors for both bridges. Most differences appear to be largely temperature related, although the reason behind this effect is unclear. For the Toms Creek Bridge, the largest average values from the 2003 tests are 440 me for service strain, 0.43 in. (L/484) for service deflection, 0.08 (S/11.1) for wheel load distribution, and 0.64 for dynamic load allowance. The values for the Route 601 Bridge are 220 me, 0.38 in. (L/1230), 0.34 (S/10.2), and 0.14 for the same corresponding paramters. The recommended design values for the dynamic load allowance in both bridges have been revised upwards to 1.35 and 0.50 for the Toms Creek Bridge and Route 601 Bridge, respectively, to account for variability in the data. With these increased factors, the largest strain in the toms Creek Bridge and Route 601 Bridge would be less than 13% and 12%, respectively, of ultimate strain. Therefore, the two bridges continue to provide a large factor of safety against failure. / Master of Science

No description available.

The wheel-rail contact mechanics and dynamics that are of great importance to the railroad industry are evaluated by applying statistical methods to the large volume of data that is collected on the VT-FRA state-of-the-art roller rig. The intent is to use the statistical principles to highlight the relative importance of various factors that exist in practice to longitudinal and lateral tractions and to develop parametric models that can be used for predicting traction in conditions beyond those tested on the rig. The experiment-based models are intended to be an alternative to the classical traction-creepage models that have been available for decades. Various experiments are conducted in different settings on the VT-FRA Roller Rig at the Center for Vehicle Systems and Safety at Virginia Tech to study the relationship between the traction forces and the wheel-rail contact variables. The experimental data is used to entertain parametric and non-parametric statistical models that efficiently capture this relationship. The study starts with single regression models and investigates the main effects of wheel load, creepage, and the angle of attack on the longitudinal and lateral traction forces. The assumptions of the classical linear regression model are carefully assessed and, in the case of non-linearities, different transformations are applied to the explanatory variables to find the closest functional form that captures the relationship between the response and the explanatory variables. The analysis is then extended to multiple models in which interaction among the explanatory variables is evaluated using model selection approaches. The developed models are then compared with their non-parametric counterparts, such as support vector regression, in terms of "goodness of fit," out-of-sample performance, and the distribution of predictions. / Master of Science / The interaction between the wheel and rail plays an important role in the dynamic behavior of railway vehicles. The wheel-rail contact has been extensively studied through analytical models, and measuring the contact forces is among the most important outcomes of such models. However, these models typically fall short when it comes to addressing the practical problems at hand. With the development of a high-precision test rig—called the VT-FRA Roller Rig, at the Center for Vehicle Systems and Safety (CVeSS)—there is an increased opportunity to tackle the same problems from an entirely different perspective, i.e. through statistical modeling of experimental data. Various experiments are conducted in different settings that represent railroad operating conditions on the VT-FRA Roller Rig, in order to study the relationship between wheel-rail traction and the variables affecting such forces. The experimental data is used to develop parametric and non-parametric statistical models that efficiently capture this relationship. The study starts with single regression models and investigates the main effects of wheel load, creepage, and the angle of attack on the longitudinal and lateral traction forces. The analysis is then extended to multiple models, and the existence of interactions among the explanatory variables is examined using model selection approaches. The developed models are then compared with their non-parametric counterparts, such as support vector regression, in terms of "goodness of fit," out-of-sample performance, and the distribution of the predictions. The study develops regression models that are able to accurately explain the relationship between traction forces, wheel load, creepage, and the angle of attack.

The Tom's Creek Bridge is a small-scale demonstration project involving the use of fiber-reinforced polymer (FRP) composite girders as the main load carrying members. The project is intended to serve two purposes. First, by calculating bridge design parameters such as the dynamic load allowance, transverse wheel load distribution and deflections under service loading, the Tom's Creek Bridge will aid in modifying current AASHTO bridge design standards for use with FRP composite materials. Second, by evaluating the FRP girders after being exposed to service conditions, the project will begin to answer questions about the long-term performance of these advanced composite material beams when used in bridge design. This thesis details the In-Service analysis of the Tom's Creek Bridge. Five load tests, at six month intervals, were conducted on the bridge. Using mid-span strain and deflection data gathered from the FRP composite girders during these tests the above mentioned bridge design parameters have been determined. The Tom's Creek Bridge was determined to have a dynamic load allowance, IM, of 0.90, a transverse wheel load distribution factor, g, of 0.101 and a maximum deflection of L/488. Two bridge girders were removed from the Tom's Creek Bridge after fifteen months of service loading. These FRP composite girders were tested at the Structures and Materials Research Laboratory at Virginia Tech for stiffness and ultimate strength and compared to pre-service values for the same beams. This analysis indicates that after fifteen months of service, the FRP composite girders have not lost a significant amount of either stiffness or ultimate strength. / Master of Science

more funding must be allocated for their rehabilitation or replacement. The Federal Highway Administration's (FHWA) Long-Term Bridge Performance (LTBP) Program has been developed to help bridge stakeholders make the best decisions concerning the allocation of these funds. This is done through the use of high quality data obtained through numerous testing processes. As part of the LTBP Pilot Program, researchers have performed live load tests on the U.S. Route 15 Southbound bridge over Interstate-66. The main performance and behavior characteristics focused on are service strain and deflection, wheel load distribution, dynamic load allowance, and rotational behavior of bridge bearings. Data from this test will be used as a tool in developing and refining a plan for long-term bridge monitoring. This includes identifying the primarily loaded girders and their expected range of response under ambient traffic conditions. Information obtained from this test will also aid in the refinement of finite element models by offering insight into the performance of individual bridge components, as well as overall global behavior. Finally, the methods and results of this test have been documented to allow for comparison with future testing of this bridge, which will yield information concerning the changes in bridge behavior over time. / Master of Science

The Route 601 Bridge in Sugar Grove, Virginia spans 39 ft over Dickey Creek. The Bridge is the first to use the Strongwell 36 in. fiber reinforced polymer (FRP) double web beam (DWB) in its superstructure. Replacement of the old bridge began in June 2001, and construction of the new bridge was completed in October 2001. The bridge was field tested in October 2001 and June 2002. This thesis details the field evaluation of the Rt. 601 Bridge. Using mid span deflection and strain data from the October 2001 and June 2002 field tests, the primary goal of this research was to determine the following AASHTO bridge design parameters: wheel load distribution factor g, dynamic load allowance IM, and maximum deflection. The wheel load distribution factor was determined to be S/5, a dynamic load allowance was determined to be 0.30, and the maximum deflection of the bridge was L/1500. Deflection results were lower than the AASHTO L/800 limit. This discrepancy is attributed to partial composite action of the deck-to-girder connections, bearing restraint at the supports, and contribution of guardrail stiffness. Secondary goals of this research were to quantify the effect of diaphragm removal on girder distribution factor, determine torsion and axial effects of the FRP girders, compare responses to multiple lane symmetrical loading to superimposed single lane response, and compare the field test results to a finite element and a finite difference model. It was found that diaphragm removal had a small effect on the wheel load distribution factor. Torsional and axial effects were small. The bridge response to multilane loading coincided with superimposed single lane truck passes, and curb-stiffening effects in a finite difference model improved the accuracy of modeling the Rt. 601 Bridge behavior. / Master of Science

No description available.