A bench-scale tubular reactor with recirculation was built in order to study the efficiency of the photocatalytic oxidation of phenol on fluidized titanium oxide-coated silica gel beads. A UV-C lamp placed along the central vertical axes of the reactor was used as source of photons. A bed of silica gel beads was fluidized by means of fluid recirculation and forced to follow upward helical flow around the lamp. Anatase was successfully synthetized on silica gel particles of average diameters 224, 357 and 461 µm, as confirmed by scanning electron micrographs, through a sol-gel technique using a titanium (iv)isopropoxide / hydrochloric acid / ethanol precursor. Data was obtained from multiple 8-hours photocatalytic experiments using a determined mass of beads fluidized in an aqueous solution of known initial phenol concentration. Contaminant degradation with irradiation time was measured as COD. Beads that had been subjected to three consecutive coating procedures produced an 8-h removal efficiency 10% higher than beads with a single coat. 20 g L-1 of silica beads was found to be the optimum load for the experimental reactor configuration regardless of beads size, although efficiency increased with decreasing size of the latter. Experimental results confirmed that the efficiency of phenol photocatalytic degradation decreases with increasing pollutant concentration. Also, the highest removal was achieved with initial pH 3, and it decreased with increasing pH. When NaCl was added to the solution, COD removal increased with increasing salinity. Additionally, it was found that dissolved oxygen is indispensable for photocatalysis to proceed, and that saturation of the treated mixture with oxygen was effectively achieved by keeping the liquid surface in contact with pure oxygen at 1 atm. Finally, statistical analysis of the data showed that photocatalytic mineralization of phenol-derived COD under the experimental conditions follows exponential decay. Based on this finding, a correlation model was proposed for the accurate prediction (minimum R2 = 0.9840) of the COD removal efficiency of the reactor for any given initial COD.

Les travaux menés au cours de cette thèse ont pour objectif d’étudier l’applicabilité du procédé d’ozonation catalytique TOCCATA® au traitement avancé d’eaux résiduaires urbaines pour le contrôle des émissions en micropolluants. Ce travail couvre la détermination des propriétés physico-chimiques, structurelles et de réactivité de deux catalyseurs et l’optimisation de leur conditionnement pour le procédé d’ozonation catalytique. La caractérisation hydrodynamique du réacteur à co-courant ascendant triphasique en lit fixe utilisé pour la mise en œuvre du procédé a été également réalisée. Les processus élémentaires impliqués dans le procédé ont ensuite été étudiés séparément : transfert gaz-liquide, adsorption, ozonation simple et interaction ozone/matériau. Enfin l’ozonation catalytique a été étudiée vis-à-vis de l’élimination de la matière organique des eaux usées réelles. L’ozonation catalytique se montre moins sélective que l’ozonation simple et améliore le procédé en termes de transfert d’ozone et d’élimination du carbone organique. Des mécanismes et des lois cinétiques pour chacun des processus élémentaires ont été déterminés et une loi de vitesse globale de premier ordre pour le procédé d’ozonation catalytique est proposée. L’étude de l’influence de différentes variables opératoires a été effectuée en vue de l’optimisation du procédé. L’investigation a ensuite été élargie à l’élimination de micropolluants spécifiques (carbamazépine, diuron, kétoprofène, diclofénac, naphtalène) appliquée à des eaux synthétiques, ainsi qu’à des eaux résiduaires urbaines réelles. La plupart des composés sont dégradés après application d’une faible dose d’ozone par le procédé. L’étude de leurs propriétés et de leur affinité avec le système d’ozonation catalytique a permis d’expliquer leurs comportements. / This thesis aimed to study the application of the TOCCATA® catalytic process to urban wastewaters treatment in order to control micropolluant emissions. This work first focused on physico-chemical, structural and reactional properties of two catalysts and on the optimization of their conditioning for the use in the catalytic process. The hydrodynamic characterisation of the fixed bed triphasic co-current upflow reactor used for this study was realized. Elementary processes involved in the process were studied separately: gas-liquid transfer, adsorption, single ozonation, ozone/catalyst interactions. Catalytic ozonation was then investigated for the elimination of organic matter contained in real urban wastewaters. Catalytic ozonation appeared to be less selective than single ozonation and to improve the process in terms of ozone transfer and organic carbon removal efficiency. Mechanisms and kinetic laws were determined for each elementary process and a global first order kinetic law was proposed for catalytic ozonation. The study of various operating conditions (liquid and gas flows, ozone dose …) was conducted in order to optimize the process efficiency.Investigations were then extended towards specific micropollutants elimination (carbamazepine, diuron, ketoprofen, diclofenac, naphtalene) onto synthetic waters as well as real urban wastewaters. Most of the compounds were eliminated with low dose ozonation by the TOCCATA® catalytic ozonation process. The properties of the micropollutants and their affinities with the catalytic ozonation system were studied in order to explain their behaviours.

Cette étude porte sur l’application de différents procédés d’oxydation avancée, POA (plasma d'air humide, électro-Fenton, photo-Fenton et oxydation anodique avec BDD) pour le traitement des colorants de textile. La particularité de ces procédés tient à la génération dans le milieu d’entités très réactives et très oxydantes, les radicaux hydroxyles •OH qui sont capables d’oxyder n’importe quelle molécule organique jusqu’au stade ultime d'oxydation, c'est-à-dire la minéralisation (transformation en CO2 et H2O). Le plasma d'air humide a été appliqué pour l'oxydation d'un colorant azoïque, l'OD 61. Différents catalyseurs (Fe2+, Fe3+ et TiO2) ont été ajoutés dans leurs conditions optimisées afin d'améliorer les performances du système Glidarc. La combinaison des deux catalyseurs: Fe2+ et TiO2 a permis de décolorer 91% de l'OD 61 au bout de 3 heures et d'atteindre un taux d'abattement du COT de l'ordre de 52% après 10 heures de traitement. La méthodologie de la recherche expérimentale a été appliquée dans ce mémoire afin d'étudier l'influence de: l'intensité du courant, la concentration du colorant et le temps d'électrolyse sur la vitesse de disparition de l'OD 61 et afin de déterminer les conditions optimales de sa minéralisation. Dans les conditions optimales obtenues ([colorant] = 0,53.10-3 mol.L-1, I = 250 mA), le procédé électro-Fenton (EF) permet d'atteindre des taux de minéralisation de l'ordre de 98% dans le cas de l'OD 61 et l'AO 7 et de 88% dans le cas de l'indigo carmine. L’identification des produits intermédiaires au cours de l’électrolyse a permis de proposer un mécanisme de minéralisation de l'AO7. Les constantes cinétiques apparentes et absolues ont été déterminées. La dégradation de l'indigo a été étudiée par oxydation anodique avec BDD (OA-BDD) et par procédé photo-Fenton (PF). Cette étude a montré que l'électrolyse de l'indigo suit une cinétique de pseudo premier ordre et que le taux d'abattement du COT était de l'ordre de 97% et 63% respectivement avec OA-BDD et PF. Une étude comparative pour l'oxydation de l'AO 7 a été menée par trois procédés d'oxydation avancée: PF, OA- BDD et EF-Pt et EF-BDD. Cette étude a montré que le procédé photo-Fenton permet d'atteindre des taux d'abattement supérieurs à 90% après seulement 2 heures de traitement. Toutefois, le PF s'est révélé le plus coûteux suite à l'utilisation de la lumière artificielle UV et l'ajout des réactifs. Par ailleurs, le traitement d'un effluent réel issu de l'industrie de textile par le procédé électro-Fenton avec une anode de platine a permis la minéralisation presque totale du rejet initial (94% du COT initial ont été éliminés) / This study concerns the application of various advanced oxidation processes, AOP (humid air plasma, electro-Fenton, photo-Fenton and anodic oxidation with BDD) to treatment of wastewater containing the persistent organic pollutants such as textile dyes. The characteristic of these processes is due to the generation of very reactive and very oxidizing species, hydroxyl radicals •OH which are able to oxidize any organic molecule until the ultimate oxidation stage, i.e. mineralization (transformation into CO2 and H2O). The humid air plasma was applied for DO 61degradation. Various catalysts (Fe2+, Fe3+ and TiO2) were added under their optimized conditions in order to improve the performances of Glidarc system. The combination of Fe2+and TiO2 lead to reach 91% of DO 61 degradation after 3 hours and 52% of TOC abatement after 10 H of treatment. The experimental design methodology was applied in this work in order to investigate the influence of experimental parameters (current intensity, dye concentration and electrolysis time) on the degradation rate of DO 61 dye and then for determining the optimal mineralization conditions. Under the optimal obtained conditions ([dye] = 0.53 10-3 mol.L-1, I = 250 mA), electro-Fenton process can lead to a complete mineralization of dyes: 98% of TOC abatement are obtained in the case of the DO 61 and the AO 7 and 88% in the case of indigo carmine. The identification of the intermediates during electrolysis permitted to propose a mineralization of AO 7 dye under examination. The apparent and absolute kinetic constants were determined. The degradation of indigo dye was studied by anodic oxidation with BDD (AO-BDD) and photo-Fenton process (PF). This study shows a pseudo first order reaction kinetics for indigo degradation. The mineralization efficiency is about 97% and 63% of TOC abatement, respectively with OA-BDD and PF A comparative study of the mineralization efficiency of AO 7 dye was been investigated by different advanced oxidation processes (PF, AO-BDD, EF-Pt, EF-BDD). This study shows that PF process lead to reach more than 95% of TOC abatement after only 2 hours. Nevertheless, this process is the most expensive due to the use artificial UV light and the addition of reagents. The treatment of an industrial textile effluent by electro-Fenton process lead to a complete mineralization (94% of initial TOC were eliminated)

O lixiviado de aterro sanitário possui constituição complexa e é altamente poluente. Neste contexto, os processos oxidativos avançados se destacam como pré-tratamento, objetivando a remoção ou diminuição da recalcitrância do lixiviado. Neste trabalho foram utilizados os Processos Oxidativos Avançados (POAs) foto-Fenton, ozônio e ozônio combinado com peróxido de hidrogênio. Avaliou-se a influência do pré-tratamento por air-stripping, a variação na produção de ozônio em 80 e 100%, a melhor dose de peróxido de hidrogênio correspondente a 20, 40 e 80% da dose de 6g O3/L empregada nos tratamentos com ozônio, a remoção de matéria orgânica, nitrogênio amoniacal total (NAT), alcalinidade, sólidos dissolvidos totais (SDT) (cloretos), produção de nitrito e nitrato, melhor razão molar [H2O2]/[Fe2+] para o tempo de contato de 80 min no foto-Fenton, uso do número médio de oxidação do carbono (NMOC) e a quantificação do ácido oxálico formado após a aplicação dos POAs. O tratamento por O3/H2O2 (1,2 g H2O2/L e produção de O3 em 80%) obteve a maior remoção de matéria orgânica, 0,14 g massa removida de Carbono Orgânico Total (COT) / massa consumida de O3 e 0,43 g/g para a Demanda Química de Oxigênio (DQO). Quanto ao foto-Fenton, averiguou-se o máximo de 74% remoção de COT e 65% remoção DQO para a razão molar [H2O2]/[Fe2+] igual a 2. Também se notou formação de sólidos sedimentáveis neste processo aplicado ao lixiviado bruto. O pré-tratamento por air-stripping não promoveu incremento na remoção de matéria orgânica. As concentrações de NAT, alcalinidade, SDT (cloretos) se mantiveram elevadas após a aplicação dos POA. Ocorreu formação de nitrato em todos os tratamentos. O uso do NMOC foi adequado e demonstrou ocorrência de oxidação nos processos. A quantificação do ácido oxálico formado após a aplicação dos POAs não foi apropriada nesta pesquisa. / The landfill leachate is a major waste produced by the landfill and its constitution complex and highly polluting motivate research in order to adapt their disposal on the environment. In this context, the advanced oxidation processes stand out as a pretreatment, in order to remove or decrease the recalcitrance of the leachate. In this work we used the photo-Fenton AOPs, ozone and ozone combined with hydrogen peroxide. We evaluated the effect of pretreatment for air-stripping, the variation in the production of ozone 80 and 100%, the best dose of hydrogen peroxide equal to 20, 40 and 80% of the dose of 6g O3/ L used in the treatments with ozone, the removal of organic matter, total ammonia nitrogen, alkalinity, dissolved solids (chlorides), production of nitrite and nitrate, best molar ratio [H2O2]/[Fe2+] to the contact time of 80 min in the photo-Fenton, average number of carbon oxidation use and the measurement of oxalic acid formed after application of the AOPs. The AOP O3/H2O2 (1.2g H2O2/L and O3 production by 80%) had the highest removal of organic matter, 0.14 g of TOC removed mass/ mass consumed O3 and 0.43 g/g for COD. As for the photo-Fenton, it was found a maximum of 74% removal of TOC and 65% for COD removal molar ratio [H2O2]/[Fe2+] equal to 2. It was also noted the formation of settle able solids in the process applied to the raw leachate. Pretreatment by air-stripping did not promote an increase in organic matter removal. Total ammonia nitrogen concentrations, alkalinity, dissolved solids (chlorides) remained high after application of the AOP, indicating possible oxidant demand. For nitrate formation occurred in all treatments, while only the photo-Fenton was no formation of nitrite. The use of average number of carbon oxidation was adequate and showed occurrence of oxidation processes. The quantification of oxalic acid formed after the application of AOPs was not appropriate in this research.

Oxidation reactions are of prime importance at an industrial level and correspond to a huge market. Oxidation reactions are widely practiced in industry and are thoroughly studied in academic and industrial laboratories. Achievements in oxidation process resulted in the development of many new selective oxidation processes. Environmental protection also relies mainly on oxidation reactions. Remarkable results obtained in this field contributed to promote the social image of chemistry which gradually changes from being the enemy of nature to becoming its friend and savior. This study dealt with two aspects regarding oxidation process. The first aspect represented an experimental study for the partial oxidation of benzene to phenol using Pd membrane in the gaseous phase. The second part was a theoretical study for some of the advanced oxidation process (AOPs) which are applied for contaminant destructions in polluted waters. Niwa and coworkers reported a one step catalytic process to convert benzene to phenol using Pd membrane. According to their work, this technique will produce a higher yield than current cumene and nitrous oxide based industrial routes to phenol. A similar system to produce phenol from benzene in one step was studied in this work. Results at low conversion of benzene to phenol were obtained with a different selectivity from the reported work. High conversion to phenol was not obtained using the same arrangement as the reported one. High conversion to phenol was obtained using a scheme different from the one reported by Niwa et al1. It was found that producing phenol from benzene is not related to Pd-membrane since phenol was produced by passing all reactants over a Pd catalyst. Within the studied experimental conditions, formation of phenol was related to Pd catalyst since Pt catalyst was not capable of activating benzene to produce phenol. Other evidence was the result of a blank experiment, where no catalyst was used. From this experiment no phenol was produced. A kinetic model for the advanced oxidation process using ultraviolet light and hydrogen peroxide (UV/H2O2) in a completely mixed batch reactor has been tested for the destruction of humic acid in aqueous solutions. Known elementary chemical reactions with the corresponding rate constants were taken from the literature and used in this model. Photochemical reaction parameters of hydrogen peroxide and humic acid were also taken from the literature. Humic acid was assumed to be mainly destroyed by direct photolysis and radicals. The rate constant for the HA- reaction was optimized from range of values in the literature. Other fitted parameters were the rate constant of direct photolysis of hydrogen peroxide and humic acid. A series of reactions were proposed for formation of organic byproducts of humic acid destruction by direct photolysis and radicals. The corresponding rate constants were optimized based on the best fit within the range of available published data. This model doesn't assume the net formation of free radicals species is zero. The model was verified by predicting the degradation of HA and H2O2 for experimental data taken from the literature. The kinetic model predicted the effect of initial HA and H2O2 concentration on the process performance regarding the residual fraction of hydrogen peroxide and nonpurgeable dissolved organic carbon (NPDOC). The kinetic model was used to study the effect of the presence of carbonate/bicarbonate on the rate of degradation of NPDOC using hydrogen peroxide and UV (H2O2/UV) oxidation. Experimental data taken from literature were used to test the kinetic model in the presence of carbonate/bicarbonate at different concentrations. The kinetic model was able to describe the trend of the experimental data. The kinetic model simulations, along with the experimental data for the conditions in this work, showed a retardation effect on the rate of degradation of NPDOC due to the presence of bicarbonate and carbonate. This effect was attributed to the scavenging of the hydroxyl radicals by carbonate and bicarbonate. A kinetic model for the degradation of methyl tert-butyl ether (MTBE) in a batch reactor applying Fenton's reagent (FeII/ H2O2) and Fenton-like reagent (Feo/ H2O2) in aqueous solutions was proposed. All of the rate and equilibrium constants for hydrogen peroxide chemistry in aqueous solutions were taken from the literature. Rate and equilibrium constants for ferric and ferrous ions reactions in this model were taken from the reported values in the literature, except for the rate constant for the reaction of ferric ions with hydrogen peroxide where it was fitted within the range that was reported in the literature. Rate constant for iron dissolution was also a fitted parameter. The mechanism of MTBE degradation by the hydroxyl radicals was proposed based on literature studies. The kinetic model was tested on available experimental data from the literature which involved the use of Fenton's reagent and Fenton-like reagent for MTBE degradation. The degradation of MTBE in Fenton's reagent work was characterized to proceed by two stages, a fast one which involved the reaction of ferrous ions with hydrogen peroxide (FeII/H2O2 stage) and another, relatively, slower stage which involved the reaction of ferric ions with hydrogen peroxide (FeIII/H2O2 stage). The experimental data of MTBE degradation in the FeII/H2O2 stage were not sufficient to validate the model, however the model predictions of MTBE degradation in the FeIII/H2O2 stage was good. Also, the model was able to predict the byproducts formation from MTBE degradation and their degradation especially methyl acetate, and tert-butyl alcohol. The effect of each proposed reaction on MTBE degradation and the byproducts formation and degradation was elucidated based on a sensitivity analysis. The kinetic model predicted the degradation of MTBE for Fenton-like reagent for the tested experimental data. Matlab (R13) was used to solve the set of ordinary nonlinear stiff differential equations that described rate of species concentrations in each advanced oxidation kinetic model. Niwa, S. et al., Science 295 (2002) 105

A presença de antibióticos no meio ambiente aquático tem causado crescente preocupação mundial. Além dos relatos de resistência de bactérias a antibióticos, essa classe de fármacos também pode causar efeitos tóxicos e atuar como perturbadores endócrinos em diversos organismos vivos e, possivelmente, em humanos. Dentre os antibióticos comumente usados destacam-se as sulfonamidas, detectadas em águas subterrâneas e superficiais. Os processos avançados de oxidação (POA) têm sido apontados como tecnologias eficientes para tratamento de poluentes recalcitrantes em diferentes matrizes aquosas. Dentre os POA, o processo foto-Fenton é uma alternativa para a degradação de compostos não biodegradáveis, incluindo fármacos. Uma vez que a principal limitação do processo é o intervalo de pH (2,5- 4,0), a reação pode ser vantajosamente conduzida empregando-se substâncias bio-orgânicas solúveis (BOS) como agentes complexantes de Fe3+ em condições ligeiramente ácidas (pH 5). Por sua vez, o emprego da energia ultrassônica tem sido menos estudado. Nesse contexto, o objetivo deste trabalho é estudar a degradação do antibiótico sulfadiazina (SDZ) por meio do processo foto-Fenton na presença de substâncias bio-orgânicas solúveis (UVvis/ Fe3+/H2O2/BOS) e do processo de cavitação por meio de ultrassom (US). Os resultados obtidos mostram que a sulfadiazina é eficientemente degradada por ultrassom de alta frequência. As maiores porcentagens e taxas de remoção são obtidas usando menor frequência de operação (580 kHz), maior potência dissipada e em pH ligeiramente ácido (melhor condição: pH 5,5). Além disso, a reação de Fenton, combinada com o tratamento US, melhorou notavelmente a degradação da SDZ, particularmente quando quantidades extras de H2O2 foram adicionadas ao sistema. Por sua vez, o uso de BOS como aditivos no processo foto-Fenton apresenta influência marcante na fotodegradação da SDZ em condições ligeiramente ácidas (pH 5). Os BOS podem estabilizar espécies de ferro em solução aquosa em pH próximos ao neutro, o que constitui uma propriedade de grande interesse. Sob as condições estudadas, o BOS CVT230 foi mais eficiente do que FORSUD, provavelmente devido às diferenças nos grupos funcionais presentes na composição destas substâncias. Finalmente, foram calculados os indicadores de consumo de energia elétrica por ordem de grandeza (EEO) para o processo de ultrassom (1572 kW h m-3 ordem-1) e área do coletor por ordem de grandeza (ACO) para o processo foto-Fenton (8,07 m2 m-3 ordem-1). / The potential impacts of antibiotic residues in the environment have become an emerging concern during recent years due to their relation with the development of resistant bacteria, and in some cases to their ability to cause toxic and endocrine disrupting effects in humans and other living organisms. Highlighted among the commonly used antibiotics are the sulfonamides, detected in groundwater and surface water. Advanced oxidation processes (AOP) might constitute an important alternative to deal with pharmaceuticals degradation. Among them, the photo-Fenton process has been widely used. One of its major drawbacks is the highly acidic pH needed (2,5-4,0) to avoid the formation of photochemically inactive iron oxides and hydroxides. The ability of soluble bio-organic substances (SBO) to complex metal cations such as iron is useful for the development of photo-Fenton at mild acidic conditions (pH 5). In turn, the use of ultrasonic energy has been less studied. In this context, the aim of this work is to study the degradation of the antibiotic sulfadiazine (SDZ) by the photo-Fenton process in the presence of soluble bio-organic substances (UV-vis/Fe3+/H2O2/SBO) and by ultrasonic cavitation (US). The results confirm that SDZ is effectively degraded by highfrequency ultrasound. Higher SDZ percent removals and removal rates were observed for the lowest operating frequency (580 kHz), higher dissipated power, and in slightly acidic solution (pH 5.5). On the other hand, SDZ degradation is highly improved in the case of the US/ Fe(II)/H2O2 system. The use of the SBO as Fenton additives in turn has a remarkable influence in SDZ photodegradation at slightly acid conditions (pH 5). This could be ascertained to the complexation of iron by the SBO, hence maintained in the reaction medium as a photoactive species. Under the studied conditions, the BOS CVT230 was more efficient than FORSUD, probably due to differences in the functional groups present in the composition of these substances. Finally, the figures-of merit electrical energy per order (EEO) and collector area per order (ACO) were calculated for the ultrasound (1572 kW h m-3 ordem-1) and photo-Fenton (8,07 m2 m-3 ordem-1) processes respectively.

Im Rahmen der vorliegenden Arbeit wurden zwei verschiedene Klassen oxidischer Nanomaterialien nasschemisch synthetisiert und strukturell-morphologisch charakterisiert. Zum einen betrifft dies TiO2-, TiO2/SiO2-, Ag/TiO2- und Pd/TiO2-Sole, welche die photokatalytisch aktive Modifikation Anatas in nanokristalliner Form enthalten und über einen solvothermalen Sol-Gel-Prozess hergestellt werden konnten. Im Hinblick auf eine potentielle Anwendung in der Desinfektionstechnologie und für den Abbau organischer Umweltschadstoffe wurde die photokatalytische Aktivität von Pulvern und Beschichtungen auf Textil durch E. coli-Abtötung bzw. Modellfarbstoffabbau untersucht. Im Weiteren wurde die antimikrobielle Aktivität pyroelektrischer LiNbO3- und LiTaO3-Pulvermaterialien unter zyklischer thermischer Anregung nachgewiesen. Diese als Pyroelektrokatalyse bezeichnete Nutzung des pyroelektrischen Effektes in einem katalytischen bzw. elektrochemischen Prozess ist dabei von grundlegender Neuheit. Aufsetzend auf den physiko-chemischen Grundlagen dieses Phänomens wurde eine Hypothese des Mechanismus entwickelt und in Analogie zur Photokatalyse diskutiert. / This thesis deals with two classes of oxidic nanomaterials that were synthesized by chemical solution routes and characterized with respect to structure and morphology. Sols of TiO2, TiO2/SiO2, Ag/TiO2 and Pd/TiO2 containing the photocatalytically active modification anatase in nanocrystalline form were prepared via a solvothermal sol-gel process. With regard to potential application in disinfection and environmental remediation technology the photocatalytic activity of powders and coatings on textile was investigated by means of E. coli decomposition and organic dye degradation. Further the antimicrobial activity of pyroelectric LiNbO3 and LiTaO3 powder materials under cyclical thermal excitation was demonstrated. In this context the application of the pyroelectric effect in a catalytic or electrochemical process – termed as pyroelectrocatalysis – is of fundamental novelty. Based on the physico-chemical principles of the phenomenon a hypothesis of the mechanism was developed and discussed in analogy with photocatalysis.

L’aigua és un bé escàs i finit, i degut a factors com l’increment de la població i el canvi climàtic, les previsions indiquen que a mig termini un 40% de la població viurà amb un estès hídric significatiu. Això podria tenir efectes molt greus en el desenvolupament i en el benestar a les àrees afectades. És normal doncs, que els darrers anys hagi acrescut considerablement l’interès en l’obtenció de recursos hídrics alternatius i sostenibles com la regeneració d’aigua i la reutilització. Els avenços tecnològics per al tractament d’aigües estan fent possible l’obtenció d’aigua regenerada de qualitat que pot ser utilitzada per a restauració ambiental, per al reg en general i per a usos urbans no potables. Tot i així, aquesta activitat podria suposar un perill per la presència de patògens d’origen entèric (bacteris, virus i protozous) i també per la presència de microcontaminants com productes farmacèutics, hormones o subproductes de desinfecció. El RD 1620/2007 estableix el marc legal de la reutilització, i es basa en E. coli com a indicador de qualitat microbiològica de l’aigua regenerada (AR). Tot i així, E. coli pot no ser suficient en relació a la presència de patògens vírics o protozous. Un exemple és Cryptosporidium, que s’ha convertit en un patogen de referència ja que ha causat nombrosos brots de criptosporidiosi d’origen hídric. L’ús de microorganismes indicadors alternatius com bacteriòfags (SOMCPH o FRNAPH) o espores de clostridis reductors del sulfit (SRC), pot ser molt útil per a indicar la presència o per modelar el comportament de patògens vírics o de protozous. En aquesta tesi s’estudia d’una banda, la qualitat microbiològica de l’AR que produeixen cinc plantes de tractament, analitzant E. coli, indicadors alternatius, i Cryptosporidium com a patogen de referència. Es fan assajos de QMRA lligats a Cryptosporidium en les EDARs estudiades, i finalment s’estudien les implicacions, d’un procés de reutilització per a augmentar el cabal del riu Llobregat uns Km més a munt del punt de captació de la potabilitzadora. Els resultats d’aquesta part indiquen que la reutilització per a potabilització en l’escenari estudiat, no hauria de suposar cap risc per a la salut de les persones des de la perspectiva de les malalties infeccioses. S’observa que l’ús d’un altre indicador, a part d’E. coli, significaria una millora en la gestió de l’AR ja que permetria fer un seguiment molt més acurat tant de la qualitat de l’aigua com de l’eficiència dels diferents tractaments. És recomanable l’ús de tractaments multibarrera durant la regeneració per poder garantir una aigua segura, i en aquest sentit, la inclusió de llum UV és vital en la prevenció del risc associat a Cryptosporidium en AR. D’altra banda s’estudien processos fotocatalítics d’oxidació avançada (POAs) com a processos de regeneració en l’eliminació de microorganismes d’efluents secundaris reals. D’una banda, amb l’ús de làmpades d’UV i de l’altra amb l’ús de la radiació solar com a font de llum UV. Per fer-ho es va analitzar la inactivació de diferents indicadors (SOMCPH, FRNAPH, CB390PH i SRC) davant alguns POA: H2O2/UV, TiO2/UV i foto-Fenton. Els resultats indiquen que l’ús de POA té un gran potencial com a tractaments terciaris en el futur, especialment si estan basats en la radiació solar, ja que podrien ser una opció ambientalment sostenible i alhora eficaç en el tractament d’aigua. Tot i així, és necessari segui investigant la possible aplicació d’aquestes tecnologies ja que encara hi ha certes limitacions que fan que de moment no es facin servir de manera més estesa. Finalment, els resultats pel que fa a la inactivació de microorganismes ratifiquen que l’ús d’un altre indicador seria útil per assegura la qualitat microbiològica de l’aigua. / Population growth and climate change may worsen the current water scarcity problems, which could have serious effects on the development and on the public health of the affected areas. Therefore, there is an increasing interest in the improvement of sustainable water resources such as water reclamation. Technological advances in water treatment are making it possible to obtain reclaimed water (RW), which can be used for instance, for environmental restoration or for irrigation. However, water reuse may represent a health risk due to the presence of enteric pathogens or micropollutants. Spanish regulations on RW are based on E. coli, but it may not be useful to protect against viral o protozoan diseases. Cryptosporidium has become a reference pathogen since it has caused numerous waterborne outbreaks. Thus, the use of alternative indicators such as somatic coliphages (SOMCPH) or spores of sulphite reducing clostridia (SRC) may be better to monitor presence and behaviour of certain pathogens. The aims of this thesis were: (i) to study the microbiological quality of RW analysing Cryptosporidium as the reference pathogen and different microbial indicators such as E. coli, SOMCPH and SRC; (ii) to perform QMRA analysis related to the presence of Cryptosporidium in RW; (iii) to analyse the implications of planned-IPR (indirect potable reuse) in the Llobregat River; (iv) to test the effect of different AOP (advanced oxidation processes) on indicator microorganisms for water reclamation purposes. From the infectious diseases point of view, the health risks due to waterborne pathogens linked to planned-IPR in the Llobregat River can be safely managed. Furthermore, the use of another indicator, besides E. coli, would improve RW management. Multi-barrier systems including UV for water treatment are recommended to ensure RW quality, especially with regard to Cryptosporidium inactivation. AOPs have a great potential for water reclamation in the future, especially those based on solar light, because they are sustainable and effective technologies for the removal of microorganisms as well as for the mineralisation of emerging micropollutants. Within the solar based procedures, photo-Fenton showed the best performance in microbial inactivation during the experiments. However, it is necessary to further investigate this AOP to overcome some of its actual limitations.

The microbial aggregates (flocs) formed during secondary biological treatment of wastewater shield microbes from exposure to ultraviolet (UV) light, and decrease the efficiency of disinfection, causing the tailing phenomena. This thesis investigates whether the formation of compact cores within flocs induces higher levels of UV resistance. Moreover, it investigates the effect of secondary treatment conditions on the physicochemical properties of flocs’, effluent quality, and UV disinfection performance. Compact cores were isolated from the flocs using hydrodynamic shearing. The UV dose response curves (DRC) were constructed for flocs and cores, and the 53-63 μm cores showed 0.5 log less disinfectability, compared to flocs of similar size. Based on a structural model developed for the UV disinfection of flocs, floc disinfection kinetics was sensitive to the core’s relative volume, their density, and viability. The UV disinfection and floc properties of a conventional activated sludge (CAS) system, and a biological nutrient removal (BNR-UCT) system, including both biological nitrogen and phosphorus removal, was compared. The 32-53 μm flocs and the final effluent from the BNR-UCT reactor showed 0.5 log and 1 log improvement in UV disinfectability, respectively, compared to those from the CAS reactor. The BNR-UCT flocs were more irregular in structure, and accumulated polyphosphates through enhanced biological phosphorus removal. Polyphosphates were found to be capable of producing hydroxyl radicals under UV irradiation, causing the photoreactive disinfection of microorganisms embedded within the BNR-UCT flocs, accelerating their UV disinfection. Comparing the UV disinfection performance and floc properties at various operating conditions showed that increasing the operating temperature from 12 ºC to 22 ºC, improved the UV disinfection of effluent by 0.5 log. P-Starved condition, i.e. COD:N:P of 100:10:0.03, decreased the average floc size and sphericity, both by 50%. Despite the higher effluent turbidity of the P-Starved reactor, the final effluent’s UV disinfection improved by at least 1 log compared to the P-Normal and P-Limited conditions. The improvement in the floc and effluent disinfectability were accompanied by a decrease in floc sphericity and a decrease in the number of larger flocs in the effluent, respectively.

The microbial aggregates (flocs) formed during secondary biological treatment of wastewater shield microbes from exposure to ultraviolet (UV) light, and decrease the efficiency of disinfection, causing the tailing phenomena. This thesis investigates whether the formation of compact cores within flocs induces higher levels of UV resistance. Moreover, it investigates the effect of secondary treatment conditions on the physicochemical properties of flocs’, effluent quality, and UV disinfection performance. Compact cores were isolated from the flocs using hydrodynamic shearing. The UV dose response curves (DRC) were constructed for flocs and cores, and the 53-63 μm cores showed 0.5 log less disinfectability, compared to flocs of similar size. Based on a structural model developed for the UV disinfection of flocs, floc disinfection kinetics was sensitive to the core’s relative volume, their density, and viability. The UV disinfection and floc properties of a conventional activated sludge (CAS) system, and a biological nutrient removal (BNR-UCT) system, including both biological nitrogen and phosphorus removal, was compared. The 32-53 μm flocs and the final effluent from the BNR-UCT reactor showed 0.5 log and 1 log improvement in UV disinfectability, respectively, compared to those from the CAS reactor. The BNR-UCT flocs were more irregular in structure, and accumulated polyphosphates through enhanced biological phosphorus removal. Polyphosphates were found to be capable of producing hydroxyl radicals under UV irradiation, causing the photoreactive disinfection of microorganisms embedded within the BNR-UCT flocs, accelerating their UV disinfection. Comparing the UV disinfection performance and floc properties at various operating conditions showed that increasing the operating temperature from 12 ºC to 22 ºC, improved the UV disinfection of effluent by 0.5 log. P-Starved condition, i.e. COD:N:P of 100:10:0.03, decreased the average floc size and sphericity, both by 50%. Despite the higher effluent turbidity of the P-Starved reactor, the final effluent’s UV disinfection improved by at least 1 log compared to the P-Normal and P-Limited conditions. The improvement in the floc and effluent disinfectability were accompanied by a decrease in floc sphericity and a decrease in the number of larger flocs in the effluent, respectively.