No description available.

Six poly(ether ketone ketone)/carbon composite panels were manufactured from powder coated towpreg. All six panels were initially processed using a hot press equipped with controlled cooling. Four of the panels were used to investigate the effect of cooling rate on crystallinity. A fifth panel was used to investigate the effect of annealing the composite after completion of the standard fabrication process. The sixth panel was used to investigate changes in toughness due to manufacturing towpreg with polymer that had been reclaimed from the towpreg fabrication system’s air cleaner. Cooling rates of 2°C/min, 4°C/min, 6°C/min, and 8°C/min resulted in composites with crystallinities of 33%, 27%, 24%, and 23%, respectively. The principal investigation of the effect of cooling rate on crystallinity and mode I and mode II strain energy release rates, G_Ic and G_IIc, respectively, showed that G_Ic and G_IIc values increase with increasing cooling rate. Comparison of the toughness values as a function of crystallinity showed that the dependence of toughness on crystallinity is approximately equivalent to the dependence of toughness on cooling rate. Comparison of the data from the annealed panel to that from the analogous principal panel showed that annealing increased the crystallinity and decreased the mode I strain energy release rate. There was no effect, however, on the mode II strain energy release rate. Comparison of the data from the panel made with reclaimed polymer to that from its analogous principal panel showed that the reclaimed polymer panel had equivalent crystallinity and G_Ic values. On the other hand, the G_IIc values in this panel were lower than in the analogous principal panel. / Master of Science

[pt] O uso de todos os tipos de amianto na construção civil tem diminuído drasticamente devido a problemas sérios de saúde associados a sua manipulação. De fato é previsto banir totalmente o seu uso, dentro de um curto espaço de tempo, nos países desenvolvidos bem como nos em desenvolvimento. Na necessidade de se encontrar um substituto adequado para o amianto, tem-se pesquisado compósitos de argamassa reforçada com fibras vegetais e polpas celulósicas. Devido ao processo de polpação, que remove as impurezas não celulósicas, como a lignina e a hemicelulose, diminuindo o ataque às fibras, sem a necessidade de recorrer a modificações na matriz cimentícia, as polpas celulósicas podem ser o substituto ideal para o amianto. Assim sendo, o principal objetivo desta dissertação é determinar experimentalmente as características mecânicas e os parâmetros de fratura de compósitos de matriz cimentícia reforçada por polpa de bambu refinada e sem refino. As polpas celulósicas foram utilizadas nas porcentagens de 8 e 14 por cento em relação à massa do cimento, porcentagens estas que, conforme a literatura, são associadas à otimização da energia absorvida no ensaio de flexão. A avaliação do comportamento mecânico dos compósitos considerados neste trabalho foi realizada através de ensaios de compressão e impacto, bem como de flexão em três pontos em espécimes não entalhados e em outros contendo entalhes de raios de curvatura diferentes. Propriedades mecânicas, tais como módulo de elasticidade, resistência à compressão, ao impacto e à flexão, bem como integral J na carga máxima, são apresentadas e discutidas em termos de aspectos microestruturais e fractográficos dos corpos de prova ensaiados. / [en] As handling and manipulation of asbestos pose grave health hazards, its use in civil construction has been drastically dwindling and will in fact be completely prohibited, in a few years, in developed countries. With the need arising to find an adequate substitute, vegetable fibers and cellulosic pulps have been considered to be viable alternatives. Taking into account the fact that the process for pulp production entails the removal of impurities, such as lignin and hemicellulose, cellulosic pulps seem to be the ideal substitute to asbestos, as their use does not necessitate modifications in the cementitious matrix. Accordingly, the purpose of this work is to experimentally determine basic mechanical characteristics and pertinent fracture parameters of bamboo pulp reinforced cement. Refined and non-refined pulps were used in the proportions of 8 and 14 percent of the weight of dry cement. These percentages were adopted as they imply, according to literature, in optimizing the energy absorbed by the composite in bend loading. Evaluation of the mechanical behavior of the composites considered in this work was realized by means of compression and impact testing. Three point bend tests were also carried out using unnotched as well as notched specimens of different notch root radii. Mechanical properties such as modulus of elasticity, compressive, impact and bend strengths, and J integral at maximum load are presented and discussed in terms of pertinent microstructural and fractographic aspects of test specimens.

Cette étude porte sur la mise en forme des matériaux composites renforcés par des fibres ou des mèches de fibres courtes tels que les SMC ou les BMC. Un travail expérimental a dans un premier temps été réalisé à l’échelle macroscopique. Ce travail a permis de mettre au point un rhéomètre de compression lubrifiée ainsi que des méthodes d’essais et de dépouillement. Ceci permet de mieux caractériser la rhéologie des compounds SMC et BMC en traitant les problématiques de leur compressibilité et des frottements éventuels entre les parois du rhéomètre et la matière déformée. Un travail numérique a ensuite permis de simuler la mise en forme d’un BMC après l’identification des paramètres d’un modèle rhéologique simple à partir des données expérimentales obtenues sur le rhéomètre. Enfin, un travail expérimental à l’échelle microscopique a permis d’une part de caractériser finement les microstuctures de SMC modèles à partir de microtomographies à rayons X, et d’autre part de caractériser et de modéliser par le biais d’essais d’extraction de fibres les interactions entre les mèches formant le renfort fibreux de ces matériaux. / This study focuses on the processing of composite materials reinforced with short fibres or fibres bundles such as SMC or BMC. Firstly, an experimental work was carried-out at the macroscopic scale. This work led to the development of a lubricated compression rheometer and associated analysis methods to better characterize the rheology of SMC and BMC compounds, by accounting for the compressibility of compounds and the possible friction between the rheometer wall and the flowing composite. Numerical simulation was then achieved in order to simulate the forming of a BMC. For that purpose, the constitutive parameters of a simple tensorial rheological model were determined from experimental data obtained with the rheometer. Finally, an experimental work at the microscopic level allowed (i) the microstuctures of SMC models from X-ray microtomography micrographs and (ii) fibre pull-out experiment to be characterized, and the interaction mechanisms between the fiber bundles forming the fiber reinforcement of these materials to be modelled.

<div>Laser-to-composite interactions are becoming increasingly common in diverse applications such as diagnostics, fabrication and machining, and weapons systems. Lasers are capable of not only performing non-contact diagnostics, but also inducing seemingly imperceptible structural damage to materials. In safety-critical venues like aerospace, automotive, and civil infrastructure where composites are playing an increasingly prominent role, it is desirable to have means of sensing laser exposure on a composite material. Self-sensing materials may be a powerful method of addressing this need. Herein, we present an exploratory study on the potential of using changes in electrical measurements as a way of detecting laser exposure to a carbon nanofiber (CNF)-modified glass fiber/epoxy laminate. CNFs were dispersed in liquid epoxy resin prior to laminate fabrication via hand layup. The dispersed CNFs form a three-dimensional conductive network which allows for electrical measurements to be taken from the traditionally insulating glass fiber/epoxy material system. It is expected that damage to the network will disrupt the electrical pathways, thereby causing the material to exhibit slightly higher resistance. To test laser sensing capabilities, a resistance baseline of the CNF-modified glass fiber/epoxy specimens was first established before laser exposure. These specimens were then exposed to an infra-red laser operating at 1064 nm, 35 kHz, and pulse duration of 8 ns. The specimens were irradiated for a total of 20 seconds (4 exposures each at 5 seconds). The resistances of the specimens were then measured again post-ablation. In this study, it was found that for 1.0 wt.% CNF by weight the average resistance increased by about 18 percent. However, this values varied for specimens with different weight fractions. This established that the laser was indeed causing damage to the specimen sufficient to evoke a change in electrical properties. In order to expand on this result, electrical impedance tomography (EIT) was employed for localization of laser exposures of 1, 3, and 5 seconds on a larger specimen, a 3.25” square plate. EIT was used to measure the changes in conductivity after each exposure. EIT was not only successful in detecting damage that was virtually imperceptible to the human-eye, but it also accurately localized the exposure sites. The post-ablation conductivity of the exposure sites decreased in a manner that was comparable to the resistance increase obtained during prior testing. Based on this preliminary study, this research could lead to the development of a real-time exposure detection and tracking system for the measurement, fabrication, and defense industries.</div>

The launch environment experiences many vibration, shock, and acoustic loads. A great concern is the high random vibration levels that can damage components and spacecraft structures, which can cause a mission failure. An effective method of reducing high frequency energy is using isolators. Overall, the need for vibration isolation has been increasing because there has been an increase in the use of mechanisms in which vibrations are prevalent. In addition, there has not been extensive research on the effects of isolators that are outgassed and cured. Therefore, it is important to investigate and understand the vibrational effects on isolators. It is convenient to outgas and cure isolators for the benefit of some components because that eliminates contamination, but outgassing and bake-out could potentially affect the frequency response of the isolator system in a negative way. It is valuable to investigate how much outgassing and bake-out might affect the performance, if any, of the vibration isolator in order to benefit companies who may need that kind of information. The vibration isolators used for the purpose of this research were twenty E22-02-40 isolators provided by Barry Controls, a Hutchinson Group Company. The E22-02-40 isolators were outgassed and cured (heated at high temperatures) in order to be turned from grade C into grade A level for outgassing. Then the vibrational performance of those isolators were tested and compared to the isolators that were not outgassed and not cured. Vibration tests were run in the flat frequency spectrum and high frequency spectrum. The maximum percent difference occurred in the grade A level isolators, in which the first frequency mode increased by 33.3 % in the z direction from the grade C isolators. A numerical finite element analysis was performed on Abaqus/CAE in order to verify the experimental results. In addition, a swelling test was conducted on the isolators to test their physical characteristics change after they were outgassed and cured.

The current dissertation, titled “Fire Response of Composite aerostructures” deals with a crucial subject of the aeronautics industry that is the fire response of composite aerostructures, more specifically the issue of interest in this work is the fuselage fire burnthrough from an external liquid jet-fuel pool fire. Other fire issues that “bother” the aeronautics industry are the fire spread inside the cabin, smoke generation and toxicity of the fumes, but these are not handled in the current dissertation. Aircraft structures are designed to withstand various loading scenarios during their operational life. These loading scenarios are associated to a great extent with normal aircraft operation (flight manoeuvres, take-off and landing). However there are situations where the aircraft structures are required to assure the safety of the passengers and crew. In the case of an emergency crash landing, the threat of an external jet-fuel fire always exists. Considering that the aircraft structure survives the impact, the survivability of the passengers and crew onboard the aircraft depends solely on the fire resistance of the aircraft structure. A measure of the fire resistance of an aircraft structure is the time needed for the flames to penetrate the fuselage and spread inside the cabin, the so-called, burn-through time. So far, the aircraft fire resistance has been extensively studied by conducting lab, medium and full scale tests. The early lab scale tests were performed by the Federal Aviation Administration (FAA) and involved the Bunsen-burner flammability test of coupons for developing fire safe interior materials. As the application of polymer materials on aircrafts kept increasing, the problem of fire burn-through due to external fire emerged. Marker was one of the first to perform full-scale fuselage burn-through tests to access the insulating performance of materials. Also a statistical analysis was performed by Cherry and Warren that accessed and analyzed data from past accidents and their work resulted in proving the importance of fuselage fire hardening and the passengers’ lives that could be saved using low-cost solutions. These works led the FAA to proposed new fire testing procedures for aircraft materials. The scope of this dissertation was to assess the performance of various structural materials in a pool-fire scenario. A simplified approach is made, approximating the pool-fire conditions with a flat panel burn-through test in accordance to the ISO2685:1998(E) Standard. The originality of the present work comes from the fact that it incorporates a multistage approach in order to investigate the behaviour and response of composite aircraft structures in the possibility of a fire event. The current approach goes down on material level in order to investigate and model the deterioration (decomposition) of the polymer composite. Thus, it investigates and proposes a methodology of how the thermophysical properties of the composite are deteriorated due to the fire event. It proceeds into developing a progressive-damage material model (material properties varying with the deterioration degree) and finally implementing this custom material model into a commercial FE package and solving the loading scenarios. Being more specific the current work begins with a quick review of the literature where incidents and work done on the burnthrough event for the past 20-30 years are summarized. It progresses then to presenting the various types of polymers used in the aircraft industry and their basic decomposition mechanisms, from the unsaturated polyesters to the epoxies and phenolics and in the end reference to the thermoplastics is made. Every organic material, hence, polymers used in aerospace applications, present a set of response characteristics when subjected to fire, specifically the heat release rate, thermal stability index, limiting oxygen index, flammability index, time-to-ignition, surface flame spread, mass loss, smoke density and smoke toxicity. Following is the backbone of this dissertation, the kinetics modelling. Two approaches are made, one simplified using single stage kinetics where the decomposition degree a is calculated based on the Arrhenius reaction theory and using the kinetic triplets (kinetic parameters) extracted from thermogravimetry, TGA, data using the Friedman multi-curve method. The second approach is more complicated and considers multi-stage decomposition of the polymer composite. Specifically a 3-stage reaction network is considered for every material, the LY-Ref, and the two modified batches, one with ammonium polyphosphate AP423 and the other both with AP423 and multi-wall carbon nanotubes MWCNT. Again the kinetic parameters, activation energy EA, frequency factor A, and reaction order n, are extracted for every step using the van Krevelen methodology. In the end using the reaction rates equations the reconstruction of the TGA curves is achieved with an error of less than 5% from the test data. Correlations that consider the material deterioration and affect the thermophysical properties of the materials are proposed. Those expressions are being developed for both of the two kinetic approaches, the single and multi stage. Another crucial part of this work is the measurement and calibration of the applied fire load. Again two fire load approaches are used, one according to the ISO2685 Standard where a propane burner was manufactured and calibrated according to the Standard for medium scale samples testing and a lab scale butane burner for small samples. The ISO2685 burner was also CFD simulated and the models calibrated against analytical expressions, ISO requirements and real measurements. The CFD simulations were performed so the heat flux or heat transfer coefficient to be extracted and used as input for the later thermal FE burnthrough models. The heat flux distribution of the lab-scale AML burner on the specimen surface was measured via a water cooled Schmit-Boelter SBG01 heat flux sensor manufactured by Hukseflux. Manufacturing and material details are presented concerning the samples used for every test campaign. Metallic (AL2024-T3) samples, CFRP neat and modified, and hybrid GLARE ones where manufactured. Also the experimental work performed is described. Cone calorimetry testing data are available, results from thermogravimetry tests, differential scanning calorimetry, and finally the burnthrough tests with both the testing apparatuses, the ISO2685 one and the AML lab-scale burner. The modelling work in this dissertation involved thermal models that were developed into a commercial FE package. It was not part of this work to develop a thermal solver so a commercial one was selected and all the developed methodology was adapted to its requirements and specifications. The boundary conditions on the models are presented both for the ‘hot’ front surface and the rear ‘cooling’ one. For the ‘hot’ one the heat flux distribution is used and for the ‘cooling’ one an equivalent convection is applied that accounts for both convective and radiative cooling. The decomposing material model is implemented into to FE solver via user defined subroutines for the single stage kinetics and the multi-stage approach. Finally the simulations were run and the results and models were compared against the available experimental results. Since so far the burnthrough response of aerostructures was limited to coupon, samples and medium size flat panels. A more realistic approach was performed by developing a mathematical model of a real size test. The certification tests conducted by the FAA are for full size fuselage sectors under the fire load of a burning jet-fuel pan pool-fire. A burning jet-fuel pool fire is a complex phenomenon on its own, combining it with a decomposing fuselage structure make the modeling approach even more difficult to simulate if not impossible. Required data for the pool-sizes under investigation were not available, so data for large external hydrocarbon pool fires from literature were used. Also, because the main characteristic of a jet-fuel (kerosene) pool fire is that the flames are not clear, on the contrary, great amount of shoot is produced making combustion modeling and radiative heat transfer to the fuselage even more of a challenge to model, it was decided to try and tackle this full-scale approach by a simplified the modeling approach. Instead of liquid fuel combustion, an equal hot air stream with mass flow, velocity and temperature properties extracted from literature correlation data was performed. Conclusively, in terms of completeness the benefit analysis performed by Cherry and Warren is presented in brief. The objective of their analysis was to assess the potential benefits, in terms of reduction of fatalities and injuries, resulting from improvements in fuselage burnthrough resistance to ground pool fires. Fire hardening of fuselages will provide benefits in terms of enhanced occupant survival and may be found to be cost beneficial if low-cost solutions can be found. The maximum number of lives saved per year in worldwide transport aircraft accidents, over the period covered by the data, if hardening measures were applied, was assessed to be 12.5 for the aircraft in its actual configuration (when the accidents occurred) and 10.5 for the aircraft configured to later airworthiness requirements. These figures are completely significant and give an extra confirmation that this work on investigating the fire response of composite aerostructures is on the right track. As the work of Cherry and Warren concluded, the fire hardening measures in order to be applicable need to be cost efficient. The concept under which this whole dissertation stepped on was to investigate the fire response of composite aerostructures and the possibility of hardening the structure itself without the use of extra protective layers that add cost and weight to the overall aircraft and its maintenance. In the end it was concluded that there is the possibility of hardening the fuselage structure by design and by material. Incorporating composites into the structure it is possible to prolong the burnthrough time at least for 4-5 minutes before auto ignition occurs on the inner side of the fuselage. Auto ignition of the inner side fuselage cabin materials is mentioned since in NONE of the burnthrough tests of the CFRP composites and the GLARE samples flame penetration was observed. / Στην παρούσα διατριβή με τίτλο «Ανάλυση της απόκρισης σύνθετων πολυμερών υλικών υπό συνθήκες φωτιάς. Εφαρμογή σε αεροπορικές κατασκευές» πραγματοποιείται εργασία στην αριθμητική προσομοίωση και πειραματική διερεύνηση της συμπεριφοράς αεροπορικών κατασκευών σε συνθήκες φωτιάς. Στην μέχρι τώρα βιβλιογραφία οι διάφοροι έλεγχοι για πιστοποίηση των αεροπορικών υλικών αλλά και των αεροσκαφών στο σύνολό τους αποτελούνταν από εκτενείς πειραματικές δοκιμές σε μεσαία κλίμακα καθώς και σε πλήρους κλίμακας κατασκευές. Οι προδιαγραφές των ελέγχων ορίζονται από την Ομοσπονδιακή Διεύθυνση Αεροπλοΐας των Ηνωμένων Πολιτειών της Αμερικής, Federal Aviation Administration FAA. Όπως γίνεται αντιληπτό πλήρους κλίμακας δοκιμές είναι χρονοβόρες αλλά και οικονομικά ασύμφορες, για τον λόγο αυτό τα τελευταία χρόνια πραγματοποιούνται προσπάθειες από την FAA για καθιέρωση Προτύπων ελέγχου μικρής κλίμακας τα οποία σε συνδυασμό με αριθμητικά μοντέλα θα είναι σε θέση να προβλέπουν την συμπεριφορά των αεροπορικών κατασκευών σε συνθήκες φωτιάς από την φάση του σχεδιασμού τους. Θα εξασφαλίζεται έτσι καλύτερη διαχείριση οικονομικών και υλικών πόρων. Στην βιβλιογραφία ο μεγαλύτερος όγκος αριθμητικής μοντελοποίησης έχει πραγματοποιηθεί στους τομείς της ναυπηγικής και των θαλάσσιων κατασκευών καθώς επίσης και τα τελευταία χρόνια στον τομέα της αστικής δόμησης. Αριθμητική δουλεία πάνω στην συμπεριφορά των αεροπορικών κατασκευών είναι υπερβολικά περιορισμένη και εκεί στοχεύει να συμβάλει η παρούσα διατριβή. Οι αεροπορικές κατασκευές εκτός των περιορισμών και προδιαγραφών που θέτουν οι άλλες εφαρμογές απαιτούν την ελαχιστοποίηση του προστιθέμενου βάρους στην κατασκευή. Διάφοροι τύποι πολυμερών συνθέτων υλικών χρησιμοποιούνται στην βιομηχανία, διακρινόμενα σε θερμοσκληρυνόμενα και θερμοπλαστικά. Αρχικά παρουσιάζονται τα θερμοσκληρυνόμενα ξεκινώντας από τους ευρέως χρησιμοποιούμενους πολυεστέρες και βινυλεστέρες, στις φαινολικές και εποξικές ρητίνες καταλήγοντας στους υψηλής θερμοκρασίας κυανεστέρες. Εν συνεχεία γίνεται αναφορά στα συνήθη χρησιμοποιούμενα θερμοπλαστικά, πολυπροπυλένιο PP, Poly-ether ether-ketone PEEK και polyphenylene Sulphide PPS. Φυσικά δεν παραλείπεται να γίνει σύντομη αναφορά και στις τυπικές διεργασίες θερμικής αποσύνθεσης των προαναφερθέντων πολυμερών. Η συμπεριφορά των σύνθετων πολυμερών υλικών σε συνθήκες φωτιάς περιγράφεται από κάποια χαρακτηριστικά μεγέθη τα οποία χρησιμοποιούνται για την ποιοτική και ποσοτική σύγκριση των διαφόρων υποψήφιων αεροπορικών υλικών. Συγκεκριμένα τα μεγέθη αυτά είναι: Heat Release Rate HRR, Thermal Stability Index TSI, Limited Oxygen Index LOI, Extinction Flammability Index ESI, Time-to-Ignition, Surface Flame Spread, Mass Loss, Smoke Density, Smoke Toxicity. Οι διαδικασίες ελέγχου και τα υπολογιζόμενα μεγέθη γίνονται βάσει διεθνών Προτύπων που κυρίως για τον τομέα της αεροναυπηγικής ορίζονται από την Ομοσπονδιακή Διεύθυνση Αεροπλοΐας FAA. Η αριθμητική προσομοίωση προυποθέτει γνώση της συμπεριφοράς των πολυμερών υλικών σε συνθήκες υψηλής θερμοκρασίας, για τον σκοπό αυτό πραγματοποιήθηκαν πειράματα απώλειας μάζας με χρήση θερμογραβιμετρίας TGA κατά την διάρκεια της οποίας η απώλεια μάζας καθώς και ο ρυθμός αυτής παρακολουθούνται και καταγράφονται σαν συνάρτηση του ρυθμού θέρμανσης. Μέσα από αυτά τα δεδομένα μπορεί να πραγματοποιηθεί εκτίμηση του τρόπου αποσύνθεσης του πολυμερούς. Αρχικά πραγματοποιήθηκε η θεώρηση της μονοβάθμιας αντίδρασης (single-stage reaction) που αποτελεί και την πλέον απλουστευμένη προσέγγιση. Στην θεώρηση αυτή θεωρείται πως η πολυμερής μήτρα περνάει από την «παρθένα» κατάσταση στην απανθρακομένη μέσα σε ένα βήμα. Η περιγραφή της αντίδρασης αυτής γίνεται με μια μονοβάθμια αντίδραση τύπου Arrhenius. Σε δεύτερο βήμα χρησιμοποιήθηκε κινητική θεωρία πολλαπλών σταδίων (multi-stage kinetics) σύμφωνα με την οποία πραγματοποιήθηκε ακριβέστερη προσέγγιση της απόσύνθεσης της πολυμερούς μήτρας των συνθέτων υλικών με απόκλιση μικρότερη του 5% από τα πειραματικά δεδομένα της θερμογραβιμετρείας (thermogravimetry). Και στις δύο προσεγγίσεις της αποσύνθεσης υπολογίσθηκαν οι κινηματικές παράμετροι: συντελεστής συχνότητας A (frequency factor), ενέργεια ενεργοποίησης ΕΑ (activation energy), τάξη αντίδρασης n (reaction order) για κάθε στάδιο. Με την ολοκλήρωση αυτού του σταδίου υπήρχε μια αξιόπιστη δυνατότητα αναπαράστασης της διαδικασίας αποσύνθεσης στο πείραμα της θερμογραβιμετρίας. Είναι γνωστό ότι οι διακυμάνσεις της θερμοκρασίας επηρεάζουν της τιμές των θερμοφυσικών ιδιοτήτων των υλικών. Αναλογιζόμενοι ότι στην διαρκεία της επιβολής της φλόγας στα σύνθετα υλικά όχι μόνο η θερμοκρασία αλλά και η σύσταση μεταβάλλεται συνεχώς λόγω της αποσύνθεσης κρίθηκε αναγκαία η ανάπτυξη μιας μεθοδολογίας που θα συμπεριλαμβάνει την επίδραση της αποσύνθεσης στην μεταβολή των θερμοφυσικικών ιδιοτήτων (θερμική αγωγιμότητα, ειδική θερμοχωρητικότητα και πυκνότητα) της πολυμερούς μήτρας και κατά συνέπεια του συνθέτου υλικού. Οι εξαγόμενες μαθηματικές σχέσεις χρησιμοποιήθηκαν στην αριθμητική προσομοίωση που ακολούθησε. Με σκοπό την ορθή αριθμητική μοντελοποίηση κρίνεται αναγκαία η μέτρηση και βαθμονόμηση του θερμικού φορτίου τον πειραματικών δοκιμών. Το μετρούμενο θερμικό φορτίου χρησιμοποιήθηκε εν συνεχεία ως φόρτιση στα αναπτυχθέντα μοντέλα. Χρησιμοποιήθηκαν δύο πειραματικές διατάξεις εφαρμογής φλόγας, μία μεσαίας κλίμακας σύμφωνα με τις διατάξεις του FAA Standard, που περιγράφεται στο ISO2685:1998(E) “Aircraft – Environmental test procedure for airborne equipment – Resistance to fire in designated fire zones” και μίας εργαστηριακής κλίμακος. Πραγματοποιήθηκε μέτρηση με θερμοζεύγη και καλορίμετρο νερού καθώς και αριθμητική μοντελοποίηση με χρήση CFD για την πρώτη διάταξη. Ενώ για την εργαστηριακής κλίμακας έγινε μέτρηση με θερμοζεύγη και ενός αισθητήρα θερμικού φορτίου «water-cooled Hukseflux Schmit-Boelter SBG01 sensor». Εν συνεχεία πραγματοποιήθηκε η κατασκευή των δοκιμίων των υποψήφιων υλικών καθώς και οι πειραματικές δοκιμές και έλεγχοι τους. Συγκεκριμένα πραγματοποιήθηκε: Θερμιδομετρία κώνου (cone calorimetry), Θερμογραβιμετρία (thermogravimetry), Θερμιδομετρία Διαφορικής Ανίχνευσης (Differencial Scanning Calorimetry, DSC), Μέτρηση Θερμικής αγωγιμώτητας, Δοκιμή διείσδυσης φλόγας (Fire burnthrough penetration). Καθώς ο χαρακτηρισμός της αποσύνθεσης των πολυμερών υλικών, η μεταβολή των θερμοφυσικών ιδιοτήτων, η μέτρηση και βαθμονόμηση του επιβαλλόμενου θερμικού φορτίου καθώς και οι πειραματικές δοκιμές έχουν ολοκληρωθεί ακολουθεί η αριθμητική προσομοίωση. Οι συνοριακές συνθήκες θερμικού φορτίου και ψύξης επιλέχθησαν ως εξής. Ως φόρτιση θεωρήθηκε η κατανομή του θερμικού φορτίου (σε kW/m2) στην εμπρός επιφάνεια του πάνελ. Στην ψύξη της πίσω επιφάνειας λήφθηκε υπόψη τόσο η ελεύθερη μεταφορά θερμότητας με επαφή όσο και η ακτινοβολία. Το μοντέλο της συμπεριφοράς του υλικού διαμορφώθηκε κατάλληλα ώστε να γίνει κατανοητό από τις απαιτήσεις ενός εμπορικού κώδικα Πεπερασμένων Στοιχείων επίλυσης θερμικών προβλημάτων και προσομοιώθηκαν οι πειραματικές δοκιμές διείσδυσης φλόγας των δύο πειραματικών διατάξεων, μεσαίας και εργαστηριακής κλίμακος. Πλέον της αριθμητικής προσομοίωσης της συμπεριφοράς σε φωτιά επίπεδων δοκιμίων αεροπορικών κατασκευών, πραγματοποιήθηκε προσπάθεια απλουστευμένης μοντελοποίησης των συνθηκών φλόγας ενός λιμνάζοντος όγκου καυσίμου αεροσκαφών στο εξωτερικό μιας ατράκτου. Δημιουργήθηκε ένα τρισδιάστατο ρευστομηχανικό μοντέλο πρόβλεψης του θερμικού φορτίου στην επιφάνεια μιας τυπικής ατράκτου σύμφωνα με τις προδιαγραφές γεωμετρίας του Προτύπου “Full-scale test evaluation of Aircraft fuel fire burnthrough resistance improvements” DOT/FAA/AR-98/52,1999. Τα ρευστομηχανικά αποτελέσματα συγκρίθηκαν με δεδομένα βιβλιογραφίας για μεγάλες φλεγόμενες δεξαμενές λιμνάζοντος καυσίμου. Εκτός από την μελέτη της απόκρισης των αεροπορικών κατασκευών σε συνθήκες φλόγας σκοπός της παρούσας εργασίας είναι και η παρουσίαση λύσεων οι οποίες θα έχουν την δυνατότητα της βελτίωσης της συμπεριφοράς των υπαρχουσών δομών καθώς και των μελλοντικών σύνθετων δομών. Ενδεικτικά αναφέρεται η δυνατότητα χρήσης νανοεγκλεισμάτων, και βελτιωμένων μονωτικών υλικών, π.χ. aerogels. Όπως έχει ήδη αναφερθεί οι αεροπορικές κατασκευές θέτουν τον περιορισμό της ελαχιστοποίησης του προστιθέμενου βάρους, για τον λόγο αυτό η ενίσχυση των συνθέτων υλικών θα πρέπει να πραγματοποιηθεί σε επίπεδο υλικού και σχεδιασμού. Πρέπει δηλαδή η ίδια η κατασκευή που είναι ικανή να φέρει τα μηχανικά φορτία να εξασφαλίζει και την πιστοποίηση της FAA για συνθήκες φωτιάς. Συνοψίζοντας, η παρούσα διατριβή πραγματοποιεί μια καινοτόμο, γρήγορη και αρκετά ακριβή προσέγγιση του σημαντικότατου ζητήματος της συμπεριφοράς των πολυμερικών σύνθετων αεροπορικών δομών σε συνθήκες φωτιάς Η πολυπλοκότητα του όλου φαινομένου επέβαλε την πραγματοποίηση παραδοχών και απλουστεύσεων. Καθώς όμως με την αυξανόμενη χρήση των συνθέτων υλικών στις αεροπορικές κατασκευές, ο τομέας της ασφάλειας σε συνθήκες φλόγας είναι συνεχώς αυξανόμενος και απαιτητικός. Για αυτό οι παραδοχές και θεωρήσεις της παρούσας διατριβής μπορούν να βελτιωθούν με χρήση νέων υπολογιστικών μεθόδων και πειραματικών δεδομένων με στόχο την ακόμα ακριβέστερη πρόβλεψη της συμπεριφοράς τον αεροπορικών δομών σε συνθήκες φλόγας.

The challenges faced in today’s industry require materials capable of working in chemically aggressive environments at elevated temperature, which has fueled the development of oxidation resistant materials. All-Oxide Ceramic Matrix Composites (OCMC) are a promising material family due to their inherent chemical stability, moderate mechanical properties, and low weight. However, limited information exists regarding their behavior when in contact with other high-temperature materials such as superalloys. In this work three sets of tribological tests were performed: two at room temperature and one at elevated temperature (650 °C). The tests were performed in a pin-on-disk configuration testing Inconel 718 (IN-718) pins against disks made with an aluminosilicate geopolymeric matrix composite reinforced with alumina fibers (N610/GP). Two different loads were tested (85 and 425 kPa) to characterize the damage on both materials. Results showed that the pins experienced ~ 100 % wear increase when high temperature was involved, while their microstructure was not noticeably affected near the contact surface. After high temperature testing the OCMC exhibited mass losses two orders of magnitude higher than the pins and a sintering effect under its wear track, that led to brittle behavior. The debris generated consists of alumina and suggests a possible crystallization of the originally amorphous matrix which may destabilize the system. The data suggests that while the composite’s matrix is stable, wear will not develop uncontrollably. However, as soon as a critical load/temperature combination is attained the matrix is the first component to fail exposing the reinforcement to damage which drastically deteriorates the integrity of the component.