No description available.

No description available.

Studies were conducted to evaluate the impact of landfill leachate discharge on the operation of waste water treatment plants (WWTPs). Two aspects of interferences were found: one is UV quenching substances, which are bio-refractory and able to penetrate the biological treatment processes, consequently interfere the UV disinfection in WWTPs. The other one is organic nitrogen, which can pass the nitrification-denitrification process and contribute to the effluent total nitrogen (TN). Also, treatability study was conducted for landfill gas (LFG) condensate. In a laboratory study, leachate samples were fractionated into humic acids (HA), fulvic acids (FA) and Hydrophilic (Hpi) fractions, the specific UV254 absorbance (SUVA254) of the three fractions follows: HA > FA > Hpi. However, the overall UV254 absorbance of the Hpi fraction was important because there was more hydrophilic organic matter than humic or fulvic acids. It was found that the size distribution of the three fractions follows: HA > FA > Hpi. This indicates that membrane separation following biological treatment is a promising technology for the removal of humic substances from landfill leachates. Leachate samples treated in this manner could usually meet the UV transmittance requirement of the POTWs. Also, nitrogen species in landfill leachates under various stabilization states were investigated. Although the effect of landfill stabilization state on the characteristics of organic matter and ammonia is well documented, there are few investigations into the landfill leachate organic nitrogen under different stabilization stages. Ammonia was found to leach out slower than organic matter and can maintain a constant level within the first a couple of years (< 10 years). The concentration and biodegradability of organic nitrogen were found to decrease with landfill age. A size distribution study showed that most of organic nitrogen in landfill leachates is < 1 kDa. The protein concentration was analyzed and showed a strong correlation with the organic nitrogen. Different slopes of regression curves of untreated and treated leachates indicate that protein is more biodegradable than the other organic nitrogen species in landfill leachates. XAD-8 resin was employed to isolate the hydrophilic fraction of leachate samples, hydrophilic organic nitrogen was found to be more biodegradable/bioavailable than the hydrophobic fractions. Furthermore, biological and physical-chemical treatment methods were applied to a landfill biogas (LFG) condensate to explore the feasible treatment alternatives for organic contaminant and arsenic removal efficiency. Sequencing batch reactor (SBR) showed effectiveness for the degradation of organic matter, even in an environment containing high levels of arsenic. This indicated a relatively low toxicity of organic arsenic as compared to inorganic arsenic. However, for arsenic removal, oxidation-coagulation, including biological oxidation, conventional oxidation and advanced oxidation followed by ferric salt coagulation, and carbon adsorption were not effective for what is believed to be tri-methyl arsenic. Among these, advanced oxidation-coagulation showed the best treatment efficiency (15.1% removal). Only reverse osmosis (RO) could reduce the arsenic concentration to an acceptable level to meet discharge limits. These results implied high stability and low toxicity of organic arsenic. / Ph. D.

The goal of this research is to test the design constraints of active dpp-bridged RuII,RhIII (dpp = 2,3-bis(2-pyridyl)pyrazine)) supramolecular photocatalysts for water reduction to H2 and provide mechanistic insights into the catalytic cycle. Two member of a new RuII,RhIII motifs with only one Rh-'Cl bond, [(bpy)2Ru(dpp)RhCl(tpy)](PF6)4 ( bpy = 2,2'-bipyridine, tpy = 2,2':6,2"-terpyridine) and [(bpy)2Ru(dpp)RhCl(tpm)](PF6)4, (tpm = tris(1-pyrazolyl)methane), and a cis-RhCl2 model system, [(bpy)2Ru(dpp)RhCl2(bpy)](PF6)3, were prepared. This new motif was to test whether two Rh-'Cl bonds on RhIII are required for the photocatalytic water reduction. 1H NMR spectroscopic analysis of complexes prepared using deuterated ligands was used to characterize these three RuII,RhIII supramolecular complexes. Electrochemical studies suggested that replacing bpy with a tridentate ligand on RhIII shifts the RhIII/II and RhII/I reduction couples positively, which can modulate the orbital energetics of the RhIII LUMO (lowest-unoccupied molecular orbital). This substitute also changes the rate of ligand dissociation following the reduction of RhIII. In tpm and bpy systems, RhII intermediate is more stable than that in the tpy system. All three complexes were good light absorbers in the visible region and weak emitters from their emissive Ru(dπ)-'dpp(π*) 3MLCT (metal-to-ligand charge transfer) excited states at room temperature. The population of a low-lying 3MMCT (metal-to-metal charge transfer) ES (excited state) from the 3MLCT ES contributed to the weak emission, indicating an important intramolecular electron transfer process from dpp' to RhIII upon photoexcitation. The lower-lying 3MMCT excited state in the tpm and tpy systems relative to the bpy system result in a higher rate constant (ket = 2.6 x 10^7 vs 1.7 x 10^7 s-1) for intramolecular electron transfer. Spectrophotochemical analysis suggested that all three complexes were photoinitiated electron collectors capable of collecting two electrons on the RhIII center to generate the RuII,RhI species in the presence of DMA (N,N-dimethylaniline). The observed H2 production from water using [(bpy)2Ru(dpp)RhCl(tpm)](PF6)4 and [(bpy)2Ru(dpp)RhCl(tpy)](PF6)4 established that two halides on RhIII are not necessary in the dpp-bridge RuII,RhIII supramolecular photocatalytic-water-reduction system. This new discovery opens a new approach to the design of different RuII,RhIII motifs for photocatalysis. The active species for water reduction is proposed to be [(bpy)2Ru(dpp)RhICl(TL)]3+ from [(bpy)2Ru(dpp)RhCl(TL)](PF6)4 (TL (terminal ligand) = tpy or tpm) and [(bpy)2Ru(dpp)Rh(bpy)]3+ from [(bpy)2Ru(dpp)RhCl2(bpy)](PF6)3 respectively. Included here is the design and study of a RuII,RhI complex, [(bpy)2Ru(dpp)RhCl(COD)](PF6)3 (COD =1,5-cyclooctadiene) to provide more insights into the photophysical and photochemical properties of polypyridyl RuII,RhI species. Electrochemical and photophysical studies revealed a dpp-based LUMO in this RuII,RhI complex, suggesting dpp reduction upon photoexcitation. Photochemical study found that [(bpy)2Ru(dpp)RhCl(COD)](PF6)3 is an active photocatalyst for water reduction and that additional reduction(s) is (are) required after the generation of the RuII,RhI active species in the RuII,RhIII supramolecular photocatalytic H2 production system. This hypothesis was supported by the electrocatalytic behaviors of the RuII,RhIII supramolecular complexes for proton reduction. Cyclic voltammetry results in the presence of an acid suggested that the protonolysis of the RuII,RhIIH and RuII,RhIH species are electrocatalytic H2-evolution pathways. The mechanism is acid-dependent and influenced by terminal ligand. The studies of electrocatalytic proton reduction on these RuII,RhIII complexes suggested several possible intermediates involved in the photocatalytic water reduction cycle. The insights gained from this research can provide guidance in designing new type of RuII,RhIII and RuII,RhI complexes with better photocatalytic and/or electrocatalytic H2 production performance. / Ph. D.

Les industries automobile et aéronautique sont confrontées dans le futur proche à une raréfaction des carburants fossiles, ainsi qu’au problème de pollution de l’environnement émis par les systèmes propulsifs. Pour s’affranchir de ces problèmes, l’utilisation de carburants alternatifs censés apporter rendement et préservation de l’environnement, s’est considérablement développée ces derniers temps. Cependant, leurs impacts sur la pollution, consommation et rendement de combustion ne sont toujours pas clairement établis. En particulier, il est nécessaire de quantifier leurs effets sur les phénomènes physiques clés à la base des processus que sont l’évaporation du carburant liquide et le mélange carburant vapeur/air. L’analyse expérimentale de ces processus physiques nécessite alors l’emploi de diagnostics lasers non-intrusifs et quantitatifs, permettant de mesurer des grandeurs physiques comme les distributions spatiales instantanées de température et de concentration du carburant en phase vapeur. Parmi les techniques optiques les plus attrayantes, l’imagerie de fluorescence induite par laser (PLIF) offre de nombreux avantages. L’objectif de la thèse a été, dans un premier temps, de caractériser les propriétés spectroscopiques de quatre carburants multi-composants, le kérosène (Jet A1), le Biomass-to-Liquid (BtL), le Diesel et l’Ester Méthylique Huile Végétale (EMHV) qui, mis à part le premier, possèdent des propriétés spectroscopiques encore peu connues. L’exploitation de leurs propriétés de fluorescence a ensuite permis d’évaluer leurs capacités à fournir des signaux autorisant la mesure de la température et de la concentration du carburant en phase vapeur. Dans un second temps, un étude exhaustive des propriétés de fluorescence de plusieurs cétones (3-pentanone, benzophénone) et aromatiques (fluoranthène, acénaphtène, naphtalène, 1,2,4-triméthylbenzène…) en fonction de la température et du quenching de l’oxygène moléculaire, a été réalisée à pression atmosphérique pour identifier les traceurs fluorescents potentiellement adaptés au dosage optique des quatre carburants. Les données photophysiques collectées ont ensuite été utilisées pour parfaire l’établissement des couples carburants/traceurs fluorescents ainsi que les stratégies de mesures de température et de concentration de carburant associées. L’exploitation des données acquises lors de différentes campagnes de mesures a ainsi mis en évidence la possibilité de détecter simultanément la fluorescence de plusieurs molécules aromatiques (mono-, di- et/ou tri-aromatique) naturellement présentes ou ajoutées artificiellement dans les carburants. Le cas du Diesel a nécessité le développement d’un carburant modèle pour permettre une étude de son évaporation. L’application de cette nouvelle approche PLIF a été validée sur un injecteur hélicoptère LPP de nouvelle génération fonctionnant avec trois carburants spécifiques que sont le Jet A1, le BtL et un mélange Jet A1/BtL / The automotive and aviation industries are presently confronted with the twin crises of fossil fuel depletion and environmental degradation. Research for alternative fuels, which promise a harmonious correlation with sustainable development, energy conservation, efficiency and environmental preservation, has become highly pronounced in the present context. However, their influence on pollution, consumption and combustion yield are not clearly defined yet. In particular, their effects on key physical processes that initiate these phenomena like fuel evaporation and mixing processes between fuel vapour and air have to be quantified. Experimental analysis of these processes requires the use of non-intrusive and quantitative laser diagnostics, allowing the measurement of key physical parameters like instantaneous spatial distribution of temperature and fuel vapour concentration. Among the optical techniques available thus far, planar laser-induced fluorescence (PLIF) offers many advantages for the study such processes in combustors. The objective of this thesis is then to propose and to develop innovative PLIF strategies to measure fuel distribution and mixture formation when fossil fuels and biofuels are used in aeronautical and automotive combustion chambers. In particular, the fluorescence of various fossil fuels like kerosene (Jet A1) and Diesel, the biodiesel fuel containing Esters (FAME) and the Biomass-To-Liquid fuel (BtL) are investigated. The exploitation of their fluorescence was then used to analyse their capacity to generate signals providing from fluorescent tracers (either present naturally in the fuel or chemically added) that could be used as probe molecules for the measurement of temperature and fuel vapour concentration. To select theses tracers, an exhaustive study of the fluorescence properties of various ketones (3-pentanone, benzophenone) and aromatic molecules (fluoranthene, acenapthene, naphthalene, 1,2,4-trimethylbenzene) with temperature and quenching with molecular oxygen was performed at atmospheric pressure. The photophysical data collected during these experiments have been then used to associate the various fuels with specific fluorescent tracers and to elaborate the strategies of measurement of temperature and fuel concentration associated. Exploitation of the data collected during this thesis thus highlighted the possibility to detect simultaneously the fluorescence of various aromatic molecules (mono-, di-, tri-aromatics) naturally present or artificially seeded in fuels. The specific case of Diesel required the development of a surrogate fuel which allows the study of its evaporation process. An application of these innovative strategies of PLIF measurements has been finally performed on a new generation LPP helicopter injection system running at atmospheric pressure with the following fuels: Jet A1, BtL and a mixture of Jet A1 and BtL. Results obtained allowed the validation of the PLIF strategies defined in this thesis.

La métrologie laser basée sur l’analyse de la fluorescence de traceurs moléculaires est devenue l’un des outils clefs pour l’étude expérimentale de la dynamique des fluides réactifs. Une étude spectroscopique des propriétés photophysiques de fluorescence dans le domaine spectral UV-visible de plusieurs molécules fluorescentes appartenant aux cétones aliphatiques et aux aromatiques mono- et bicycliques a permis d’approfondir la compréhension de l’influence de la température, de la pression et de la concentration d’oxygène sur leur fluorescence. Les résultats expérimentaux obtenus ont ensuite permis le développement d’un modèle de simulation du rendement de fluorescence pour les espèces aromatiques (naphtalène et toluène), qui fournit des résultats très proches de ceux mesurés.De ces résultats, le développement de la technique d’imagerie de fluorescence (PLIF) sur la phase vapeur d’un carburant multi-composant a conduit à étendre cette analyse spectrale de fluorescence au cas du kérosène (Jet A-1). La comparaison entre les propriétés de fluorescence du kérosène et des traceurs aromatiques étudiés a notamment permis d’établir une stratégie de mesure de la concentration de la phase vapeur du kérosène dans des environnements où la teneur en oxygène est variable. Les signaux de fluorescence provenant des espèces mono- et di-aromatiques contenues dans le kérosène soulignent des évolutions différentes avec les conditions de température et teneur en oxygène. L’utilisation de filtres optiques appropriés associés à deux caméras ICCD permet alors une mesure bidimensionnelle de la température et de la concentration de kérosène en phase vapeur. La thèse débouche finalement sur l’application de cette technique PLIF-kérosène en combinaison avec la technique PLIF du radical OH en sortie d’un système d’injection industriel multi-point de nouvelle génération intégré dans une chambre de combustion haute pression. / Planar laser-induced fluorescence (PLIF) diagnostic based on the optical excitation of fluorescence tracers has become a key tool for the experimental study of fluid dynamics in reactive flows. A spectroscopic fluorescence study of several organic molecules from aliphatic ketones and mono- and bi-cyclic aromatics in gas-phase was performed in a high-pressure high temperature optical cell. The experimental measurements allowed the understanding of the influence of temperature, pressure and oxygen concentration on the photophysics of these molecules in the UV/visible domain. These results were then used to successfully develop a model of fluorescence yield of the naphthalene and toluene aromatic molecules permitting the simulation of the fluorescence signals with temperature, pressure and species composition in large domains of temperature and pressure.This study has been extended to the case of a multi-component aeronautical fuel (kerosene – jet A1) containing natural aromatics. The comparison of the spectroscopic data recorded in the optical cell to those of the aromatic tracers initially probed has then permitted the definition of a kerosene-PLIF excitation/detection strategy for kerosene vapour concentration measurements in reactive gaseous flowfield containing variable oxygen concentration. Fluorescence signals from mono- and di-aromatic species in kerosene highlight significant differences in evolution with temperature and oxygen concentration. With appropriate optical filters applied to two ICCD cameras, the two-dimensional instantaneous distribution of temperature and concentration of kerosene vapour is then possible to measure in reactive flows. Finally, the kerosene-PLIF diagnostic has been applied at the exit of an innovative multi-point aeronautical injection system integrated to high-pressure kerosene/air combustor test rig. The kerosene-PLIF, combined with the radical OH-PLIF confirmed their implementation in realistic high-pressure flowfields and delivered experimental fruitful experimental information on the effect of the fuel/air mixing on the flame structure in the combustion chamber.

No description available.

L'augmentation de l'interaction lumière-matière aux échelles micro et nanométriques est un des fers de lance de la nanophotonique. En effet, le contrôle de la répartition spatiale de la lumière grâce à l'interaction résonante entre nanostructures et ondes électromagnétiques a conduit aux développements de nombreuses applications dans des domaines variés tels que les télécommunications,la spectroscopie et la détection d'objets. Le ralentissement de la lumière, sujet de la thèse, obtenue grâces à l'interférence d'ondes contre-propageantes dans des milieux périodiques ou le confinement sub-longueur d'onde dans des guides d'ondes plasmoniques, est associé à une compression des pulses lumineux et une forte augmentation du champ électrique, deux phénomènes clés pour la miniaturisation de composées optiques et l'augmentation de l'interaction lumière matière. / Enhancing light-matter interactions at micro and nanoscales is one of the spearheads of nanophotonics. Indeed, the control of the field distribution due to the resonant interaction of nanostructures with electromagnetic waves has prompted the development of numerous optical components for many applications in telecommunication, spectroscopy or sensing. A promising approach lies in the control of light speed in nanostructures. Light slowdown, obtained by wave interferences in periodic structures or subwavelength confinement in plasmonic waveguides, is associated to pulse compressions and large field enhancements,which are envisioned as key processes for the miniaturization of optical devices and the enhancement of light-matter interactions.The thesis studies both fundamental aspects and possible applications related to slow light in photonic and plasmonic nanostructures. In particular, we study the impact of periodic system sizes on the group velocity reduction and propose a novelfamily of resonators that implement slow light on very small spatial scales. We then investigate the role of fabrication disorder in slow periodic waveguides on light localization and demonstrate how modal properties influence the confinement of localized modes. Also we propose a new hollow-core photonic crystal waveguide that provides efficient and remote couplings between the waveguide and atoms thatare trapped away from it. Finally we demonstrate the important role played by slow plasmons on the emission of quantum emitters placed in nanogap plasmonic antennas and explain how large radiation efficiency can be achieved by overcoming quenching in the metal. Additionally, one part of the thesis is devoted to thederivation of a novel modal method to accurately describe the dynamics of plasmonic resonators under short pulse illumination.

La thérapie photodynamique (PDT) est une technique utilisée cliniquement pour traiter certaines maladies de la peau, la dégénérescence maculaire liée à l’âge et certains types de cancer. Elle fait intervenir trois composants : une molécule photosensible ou photosensibilisateur (PS), la lumière et l’oxygène. Après administration du PS, celui-ci va se localiser plus ou moins sélectivement dans les zones tumorales où il est alors activé par irradiation lumineuse à une longueur d’onde et une puissance données. Ceci engendre la formation d’espèces réactives de l’oxygène (ROS) très réactives, dont l'oxygène singulet1 O2, qui entraînent la destruction des tissus tumoraux par nécrose ou apoptose. Afin d’améliorer la sélectivité du traitement, différentes pistes sont actuellement exploitées dont l’élaboration de « photodynamic molecular beacons » (PMB). Dans un PMB, le photosensibilisateur (PS) est associé via un peptide à un inhibiteur 1O2, appelé quencher. Ce quencher inhibe la formation d’1O2 tant que le composé n’a pas atteint sa cible. Une fois la zone cancéreuse atteinte, des enzymes spécifiques clivent le peptide, libérant ainsi le PS qui retrouve alors sa capacité à former de l’1O2. Trouver un couple PS/quencher adéquat reste un challenge en PDT. Les propriétés photophysiques particulières des caroténoïdes et leur aptitude à inhiber la production d’1O2 font de ces derniers des quenchers potentiellement utilisables pour l’élaboration de PMBs. Chez les plantes, les caroténoïdes (carotènes et xanthophylles) sont des pigments associés à la photosynthèse, qui ont deux rôles principaux : un rôle de collecteur de lumière et un rôle photoprotecteur en protégeant le(s) système(s) photosynthétique(s) contre les dommages photooxydatifs liés à une exposition trop intense à la lumière. Ceci s’opère, entre autre, via le cycle des xanthophylles. Cette aptitude à capter de l’énergie présente un intérêt potentiel à ne pas négliger dans la perspective de la conception de PMB utilisables en thérapie photodynamique. Dans le cadre de cette thèse en co-tutelle avec la Faculté des Sciences de Bizerte nous avons ciblé les caroténoïdes présents dans trois fruits produits en Tunisie à savoir les kakis (Diospyros kaki L.), les abricots (Prunus armeniaca L.) et les pêches (Prunus persica L.) connus pour leur richesse globale en ces pigments. Divers procédés d’extractions ont été étudiés : (i) L’extraction de type Soxhlet par solvants organiques à pression atmosphérique, utilisée comme référence, (ii) l'extraction accélérée par solvant organique (ASE : Accelerated solvent Extraction) effectuée sous pression, enfin (iii) l'extraction par CO2 supercritique avec l’éthanol comme cosolvant. Pour ces deux derniers procédés, une approche par plan d’expériences (surfaces de réponses) a été utilisée pour identifier les facteurs clé et les conditions optimales d’extractions de divers caroténoïdes (pression, température, débit, % de cosolvant, temps, nombre de cycles). L'analyse par chromatographie liquide à haute performance couplée à la détection UV-Visible et à la spectrométrie de masse a ensuite permis l'identification et la quantification des caroténoïdes présents dans les extraits obtenus, permettant ainsi de comparer les profils caroténoïdiques propres à chaque fruit et les performances de chaque procédé d’extraction. Cette étude ayant révélé un profil caroténoïdique particulièrement intéressant chez le kaki par rapport aux autres fruits, une extraction et une purification des caroténoïdes de ce fruit par chromatographie liquide haute pression préparative a ensuite été effectuée afin de disposer d’une quantité suffisante de chaque caroténoïde, et parfois de leurs isomères conformationnels, en vue de l’étude de leurs propriétés photophysiques (absorption, émission de fluorescence, inhibition d’1O2) et de l’évaluation de leur intérêt potentiel en tant que quencher d’1O2 dans un édifice de type PMB / Photodynamic therapy (PDT) is a clinically used technique for treating skin diseases, age-relatedmacular degeneration but mainly some types of cancer. PDT involves three components: a photosensitive molecule named photosensitizer (PS), light and oxygen. After administration of the PS, this one will be located more or less selectively in tumoral regions where it is activated by light irradiation at appropriate wavelength and power. This leads to the formation of highly reactive and cytotoxic reactive oxygen species (ROS), especially singlet oxygen, resulting in the destruction of the tumor by necrosis or apoptosis. To improve the treatment selectivity, different strategies are being exploited, one of which is the development of "photodynamic molecular beacons" (PMB). In PMB the photosensitizer is linked via a peptide to an inhibitor of 1O2 (quencher). This quencher inhibits the formation of 1O2 as long as the compound has not reached its target, namely cancer cells. In order to inhibit the toxicity of the PS in non-target cells and restore toxicity only close to the biological target, it is necessary to find an adequate PS/quencher couple. This remains a challenge for PDT. Carotenoids are interesting candidates due to their specific photophysical properties and ability to inhibit 1O2, which makes them potential quenchers for building PMBs. In plants, carotenoids (carotenes and xanthophylls) are pigments involved in the photosynthesis, in which they play two main roles: a light collecting role and a protecting role by preserving the photosynthetic systems against photoxydative damages induced by a too intense light exposure. This protection can for instance occur via the well-known xanthophylls cycle. This capacity to catch energy presents a potential interest that should not be neglected in the framework of the design of PMBs usable in photodynamic therapy. Within the framework as part of this PhD thesis in Cotutelle with the Faculty of Sciences of Bizerte, we focused on carotenoids from three fruits produced in Tunisia: persimmon (Diospyros kaki L.), apricot (Prunus armeniaca L.) and peache (Prunus persica L.), known for their global richness in these natural pigments. Three extraction processes were investigated: (i) the Soxhlet extraction based on the use of organic solvent at atmospheric pressure and used as reference, (ii) the accelerated solvent extraction (ASE) using organic solvent under high pressure, and (iii) the supercritical fluid extraction (SFE) using supercritical CO2 and ethanol as cosolvent. For these two last processes, a design of experiments (Surface Response Design) was used to identify the key factors and optimal extraction conditions of various carotenoids (pressure, temperature, flow, % cosolvent, time, number of cycles). Then, HPLC-PDA coupled with mass spectrometry (MS) enabled the identification and quantification of carotenoids from the extracts. Thus it was possible to compare the profiles in carotenoids content from each fruit as well as the performances of each extraction process. This study showed that the carotenoidic profile in the persimmon was the most interesting as compared to the profiles in the two other fruits. Extraction and purification of the carotenoids from persimmon by preparative high pressure liquid chromatography were then performed in order to have a sufficient amount of each carotenoid and sometimes of their conformational isomers. We finally performed a study of their photophysical properties (absorption, fluorescence emission, 1O2 inhibition) in order to evaluate their potential as 1O2 quencher in molecular construction such as a PMB

This thesis presents an experimental and theoretical study of the collision dynamics of OH(A²Σ⁺) with Kr and Xe. These two systems both exhibit a significant degree of electronically non-adiabatic behaviour, and a particular emphasis of the work presented here is to characterise the competition and interplay between electronic quenching on the one hand, and electronically adiabatic collisional processes on the other. Quenching takes place close to the bottom of the deepest potential well for both systems. In collisions that remain in the excited electronic state, this same region of the potential is also largely responsible for rotational energy transfer (RET) and the collisional depolarisation of angular momentum. Therefore, the direct competition between these processes suppresses the cross-sections for RET and collisional depolarisation from their expected value in the absence of quenching. To investigate this, experiments were carried out to measure cross-sections for the collisional transfer of electronic, vibrational and rotational energy in OH(A, v=0,1) + Kr and OH(A, v=0) + Xe. In addition, measurements were made of the j-j' correlation -- that is, the relationship between the angular momentum of the OH radical before and after a collision -- in collisions with Kr and Xe, using the experimental technique of Zeeman quantum beat spectroscopy. Collisions with both Kr and Xe tend to effectively depolarise the angular momentum of the OH radical, due to the very anisotropic character of the potential on which the process occurs. Electronic quenching, which plays an essential role in both systems, is more prevalent with xenon as the crossing to the ground state potential is located in a more accessible location. These experimental results were compared with single surface quasi-classical trajectory (QCT) calculations, where the overestimate of rotational energy transfer or collisional depolarisation helps to elucidate the degree to which the presence of quenching suppresses these processes. Surface hopping QCT was then used to account for non-adiabatic transitions in the theory, which led to an improvement in agreement with experiment. However, standard surface hopping QCT theory failed to account for the full extent of quenching in these two systems. A major focus of this work is therefore on the development of an extension to standard surface hopping QCT theory to incorporate rovibronic couplings. In non-linear configurations, the excited state of the OH + Kr, Xe systems has A' symmetry, while the ground state is split into symmetric (A') and antisymmetric (A'') components. For these symmetry reasons, coupling is restricted to the two states of the same symmetry, however a rotation of the correct (A'') symmetry can induce transitions to the A'' state too. Inclusion of all three electronic states, and the relevant couplings between them, is found to be crucial for a proper description of experimental reality.