<p>The aim of third-generation photovoltaics (PV) is ultimately to achieve low-cost, high-efficiency devices. This work focused on a third-generation PV concept known as down-shifting, which is the conversion of high-energy photons into low-energy photons which are more useful for a typical solar cell. Silicon nanocrystals (Si-NCs) fabricated using electron-cyclotron resonance plasma-enhanced chemical vapour deposition (ECR-PECVD) were studied as a down-shifting material for single-junction silicon cells. A calibration was done to determine optimal deposition parameters for Si-NC formation. An experiment was then done to determine the effect of film thickness on emission, optical properties, and photoluminescence quantum efficiencies.</p> <p>Photoluminescence (PL) peaks varied depending on the stoichiometry of the films, ranging from approximately 790 nm to 850 nm. Variable-angle spectroscopic ellipsometry was used to determine the optical constants of the Si-NC films. The extinction coefficients indicated strong absorption below 500 nm, ideal for a down-shifting material. Transmission Electron Microscopy (TEM) was used to determine the size, density, and distribution of Si-NCs in two of the films. Si-NCs were seen to have an average diameter of approximately 4 nm, with larger nanocrystals more common near the surface of the film. A density of approximately 10⁵ nanocrystals per cubic micron was approximated from one of the TEM samples.</p> <p>The design and implementation of a PL quantum efficiency measurement system was achieved, using an integrating sphere to measure the absolute efficiency of Si-NC emission. Internal quantum efficiencies (IQE) as high as 1.84% and external quantum efficiencies (EQE) of up to 0.19% were measured. The EQE was found to increase with thicker films due to more intense photoluminescence; however the IQE remained relatively independent of film thickness.</p> / Master of Applied Science (MASc)

Colloidally-stable zero valent iron nanoparticles (nZVI) were synthesized through a classical redox reaction of iron sulfate with minor modifications using cellulose nanocrystals (CNCs) as stabilizers. We obtained spherical nZVI particles with high surface roughness and a mean size of 130nm. Particles remain colloidally stable after more than two months. Cellulose nanocrystals play a dual role in nZVI stability: a foreign surface to encourage stable nucleation over fast aggregation and a stabilizer to prevent iron nanoparticles aggregating into fractal colloids. Our results highlight the impact of the presence of CNCs on the rates and mechanisms of nucleation, growth, aggregation, and aging of nZVI particles, indicating promise in controlling size and morphology of similarly redox-generated nanoparticles. Cellulose nanocrystal-stabilized nZVI nanoparticles demonstrate properties well-suited for enhanced soil and groundwater remediation. //Nanocomposites composed of carboxylated cellulose nanocrystals and iron (Fe-oxCNC) were prepared through a classical redox reaction of iron sulfate using TEMPO-oxidized cellulose nanocrystals (oxCNCs) as a template and stabilizer. Morphological control over Fe-oxCNC nanoparticles was realized by varying the amount of oxCNC added to the redox process. As the molar ratio between oxCNC and Fe was increased from 1 to 8, the morphology of Fe-oxCNC nanoparticles evolved from rounded iron aggregates supported by cellulose nanocrystals to thin film iron-coatings on cellulose nanocrystals. Transmission electron microscopy (TEM), Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES), and chemical analyses (EDX, EELS) revealed that oxCNCs were coated by iron. Small changes to the density and type of functional groups on the CNC surface have large impacts on the morphology and the oxidation state of adsorbed iron nanoparticles. / Thesis / Master of Applied Science (MASc)

This study is on thermodynamics of crystalline nanoparticles of materials. It provides measurements of the equilibrium melting point of nanocrystals of zinc in a size distribution of 30 - 120 nm, as observed by using Philips CM 12 TEM and JEOL 2010F TEM/STEM, and of the heat capacity, and melting enthalpy by using Perkin-Elmer Pyris-Diamond and TA Q100 Calorimeters. The observed melting point of zinc nanoparticles is lower than that of the bulk zinc, but their heat capacity increases and enthalpy of melting decreases. During heating, the nanoparticles oxidizes and forms zinc oxide surface layer reducing the amount and size of zinc nanocrystals. Calculations based upon the Debye theory for heat capacity show that the surface atoms on the zinc nanoparticles have ~ 55 % larger vibrational amplitude and therefore increase the entropy of the surface layer over that of the interior of the particles. During cooling, the crystallization of zinc oxide encaged zinc nanodroplets occurs in two stages, which are heterogeneous and homogeneous nucleations. As the amount of zinc nanocrystals decreases and the liquid-zinc oxide interface increases, homogeneous nucleation becomes less dominant and the two-stage crystallization merges. Nano-pharmaceuticals were produced by incorporating them in a nanoporous amorphous polymer matrix by using a technique based on diffusion method. The presence of embedded nano-pharmaceuticals is shown by their lower melting point relative to the bulk pharmaceuticals and by peak-broadening of x-ray diffraction, which shows that their size lies in 70 - 100 nm range. Although no phase inversion between allotropic forms of the pharmaceutical was observed, a sample calculation for polymorphs of tin shows that such phase inversion should occur at a smaller particle size at a lower temperature. In general, these findings show the effects of the increase in the surface energy relative to bulk energy of nanoparticles, and the consequent differences between the properties of their surface atoms relative to the interior atoms. / Thesis / Master of Applied Science (MASc)

In Chapter 1, I give a basic introduction to the scientific background necessary for understanding the rest of the dissertation. I describe semiconductor nanocrystals and quantum confinement, how nanocrystals grow and a brief description of the various characterization methods. Finally, I provide some of the general considerations and chemical sources for the experiments performed in the thesis as a whole. In Chapter 2, I summarize the journey towards working with molecular precursors and show the advances and challenges in modeling and understanding conversion made a step into nanoplatelets more feasible. The chalcogenourea syntheses are not included and the modeling of the spherical nanocrystals is in a fairly summarized form here. This chapter is intended to give a brief overview of the highlights, key conclusions, and resulting questions upon which I designed my own experiments. In Chapter 3, I discuss applying precursor conversion method to nanoplatelets and focus on 3ML CdE growth. I briefly introduce nanoplatelets, explain the new conditions necessary to adapt the chalcogenourea library, demonstrate my efforts in characterizing the kinetics and growth mechanisms, and finally show the relationship of precursor reactivity and final nanoplatelet size. The “kobs catalogue” which summarizes the kinetics and sizing from STEM is an appendix at the end of the chapter. In this chapter, we put to the test the idea that we can control nanocrystal synthesis through precursor reactivity. The synthesis of nanocrystal heterostructures controlled by precursor conversion was discussed in Chapter 2. In Chapter 4, the same theory is applied to nanoplatelet synthetic conditions, but because nanoplatelet nucleation is fast compared to the total reaction time, the precursors should result in something closer to what is modeled without extraneous products. At the end of the chapter, a nanoplatelet alloy catalogue records many of the modeling and alloy experiments. Chapter 5 attempts to gather the various side projects that working with nanoplatelets has brought about. All these projects come together when thinking about how the solute supply and surface ligands might determine nanoplatelet formation, which I hope to shed some insight on. In the end, I hope to have gathered enough information to provide thoughtful answers for why nanoplatelets form, how they are ideal for studying compositional growth, and how nanocrystal alloying changes the structural and optical properties of these materials.

Sol-gel titania particles were investigated, primarily by optical techniques, by systematically varying synthesis, sample handling, and annealing variables. The material phases investigated were amorphous titania, anatase TiO2, and rutile TiO2. Annealing-induced phase transformations from amorphous TiO2 to anatase to rutile were studied by Raman scattering, infrared reflectivity, infrared absorption, x-ray diffraction, and electron energy-loss spectroscopy (EELS). Detailed experiments were carried out on the effects of annealing on the Raman and infrared spectra of anatase nanocrystals. The frequencies of the zone-center transverse optical (TO) and longitudinal-optical (LO) phonons of anatase were determined and were used in analyzing the results obtained on composites consisting of annealed solgel particles. The TO and LO frequencies of anatase were obtained from polarization-dependent far-infrared reflectivity measurements on single crystals. These results, which determined the dielectric functions of anatase, were used to explain infrared (IR) reflectivity spectra of titania nanoparticles pressed into pellets, as well as the grazing-incidence IR reflectivity observed for titania thin films. Because of the polycrystalline character of the titania nanoparticles, the surface roughness of the pressed pellets, and the island-structure character of the thin films, effective-medium theories (appropriate for composites) were used, along with the anatase dielectric functions, to interpret the experimental results. The titania nanoparticles were prepared by the hydrolysis/condensation of Ti(OC2H5)4. A polymeric steric stabilizer was used in the sol-gel synthesis in order to prevent continued agglomeration during the condensation process. This yielded particles with a relatively narrow size distribution. The amount of water used in the reaction determines the final particle size. Particles as small as 80 nm and as large as 300 nm were used throughout this work. From the colloidal suspension, loose powders, pressed pellets, and thin films were formed. These samples were subjected to different annealing processes at temperatures ranging from room temperature up to 1000 C. Two different annealing atmospheres were used: air (oxygen-containing) and argon (no oxygen). The amorphous to anatase transformation was followed by in-situ IR transmission measurements carried out during annealing. The particles as prepared are amorphous and the anatase phase could be detected, using this sensitive IR technique, at temperatures as low as 150 C. This phase transition was shown to be particle size dependent. It was also shown that introducing the stabilizer by means of the alkoxide flask instead of the water flask (during the sol-gel synthesis) decreases the anatase to rutile transformation temperature. Loose powders were found to transform more readily than dense pellets, while island-structure films were found to be the hardest to transform. Even at 1000 C, most of these films did not transform to rutile. X-ray diffraction experiments were used to determine nanocrystal sizes in anatase samples obtained by air and argon anneals at temperatures from 300 to 800 C. A correlation was found between Raman band shape (peak position and linewidth) and crystallite size, but this correlation was different for air anneals and for argon anneals. These experiments called for an interpretation based on a stoichiometric effect rather than a finite size effect. Based on this interpretation, the as-prepared particles are slightly oxygen-deficient, with a stoichiometry corresponding to TiO1.98. In the electron energy-loss experiments, a special data-analysis technique was used to extract the EELS spectrum of the titania nanoparticles from the observed substrate-plus-particles signal. This technique successfully resolved the titania absorption-edge peak. Which was found to be momentum independent. For low electron momentum, the results were consistent with the reported optical absorption edge. / Ph. D.

Inkjet printing has generated considerable interest as a technique for the patterning of functional materials in the liquid phase onto a substrate. Despite its high promise, the phenomena associated with inkjet printing remain incompletely understood. This research project investigates inkjet printing of cellulose nanocrystals (CNCs) as a possible method for the fabrication of cellulose micropatterns. CNCs were prepared from wood pulp by H₂SO₄ hydrolysis and characterized in terms of length, width, and thickness distributions by atomic force microscopy (AFM) and dynamic light scattering. Aqueous CNC suspensions were characterized in terms of shear viscosity with a rheometer. Glass substrates were cleaned with a detergent solution, aqua regia, or a solvent mixture, and characterized in terms of surface chemical composition, surface free energy, polarity, roughness, ζ-potential, and surface charge distribution in air by X-ray photoelectron spectroscopy, contact angle measurements, AFM, streaming potential, and scanning Kelvin probe microscopy (SKPM). Additionally, poly(ethylene glycol)-grafted glass substrates were prepared and characterized in terms of surface free energy, polarity, and roughness. Aqueous CNC suspensions were printed in different patterns onto the different glass substrates with a commercial, piezoelectric drop-on-demand inkjet printer. Inkjet deposited droplet residues and micropatterns were analyzed by AFM, scanning electron microscopy, and polarized-light microscopy. At low CNC concentrations (0.05 wt %), inkjet-deposited droplets formed ring-like residues due to the "coffee drop effect". The "coffee drop effect" could be suppressed by the use of higher CNC concentrations. The resulting dot-like droplet residues exhibited Maltese cross interference patterns between crossed polarizers, indicating a radial orientation of the birefringent, elongated CNCs in these residues. The observed Maltese cross interference patterns represent unprecedented indirect evidence for a center-to-edge radial flow in drying droplets. The degree of definition of the micropatterns depended strongly on the surface properties of the glass substrates. Well-defined micropatterns were obtained on aqua regia-cleaned substrates. In addition to the surface free energy and polarity, other factors seemed to play a role in the formation of the inkjet-printed micropatterns. If these factors can be identified and controlled, inkjet deposition of CNCs could become an attractive method for the fabrication of cellulose micropatterns. / Ph. D.

This thesis is concerned with fused filament fabrication (FFF) of cellulose nanocrystal (CNC) and thermoplastic polyurethane (TPU) nanocomposites, focusing on preliminary optimization of a processing window for 3D printing of mechanically responsive composites and the influence of temperature on mechanical adaptivity, thermal stability, and rheology. CNC thermoplastic nanocomposites are a water responsive, mechanically adaptive material that has been gaining interest in additive manufacturing for 4D-printing applications. Using a desktop FlashForge Pro 3D printer, we first established a viable processing window for a nanocomposite comprising 10 wt% CNCs in a thermoplastic urethane (TPU) matrix, formed into a filament through the combination of masterbatch solvent casting and single screw extrusion. Printing temperatures of 240, 250, and 260°C and printing speeds of 600, 1100, and 1600 mm/min instituted a consistent 3D-printing process that produced characterizable CNC/TPU nanocomposite samples. To distinguish the effects of these parameters on the mechanical properties of the printed CNC/TPU samples, a design of experiments (DOE) with two factors and three levels was implemented for each combination of printing temperature and speed. Dynamic mechanical analysis (DMA) highlighted 43 and 66% increases in dry-state storage moduli values as printing speed increases for 250 and 260°C, respectively. 64 and 23% increases in dry-state storage moduli were also observed for 600 and 1100 mm/min, respectively, as temperature decreased from 260 to 250°C. For samples printed at 240°C and 1600 mm/min, it was determined that that parameter set may have fallen out of the processing window due to inconsistent deposition and lower dry-state storage moduli than what the slower speeds exhibited. As a result, the samples printed at 240°C did not follow the same trends as 250 and 260°C. Further analysis helped determine that the thermal energy experienced at the higher end printing temperatures coupled with the slower speeds decreased the dry-state storage moduli by nearly 50% and lead to darker colored samples, suggesting CNC degradation. Isothermal thermogravimetric analyses (TGA) demonstrated that the CNC/TPU filament would degrade at relative residence times in the nozzle for all the chosen printing temperatures. However, degradation did not eliminate the samples' ability to mechanically adapt to a moisture-rich environment. DMA results verified that mechanical adaptivity was persistent for all temperature and speed combinations as samples were immersed in water. However, for the higher temperatures and slower speeds, there was about a 15% decrease in adaptability. Optimal parameters of 250°C and 1600 mm/min provided the highest dry-state storage modulus of 49.7 +/- 0.5 MPa and the highest degree of mechanical adaptivity of 51.9%. To establish the CNC/TPU nanocomposite's use in 4D printing applications, shape memory analysis was conducted on a sample printed at the optimal parameters. Multiple wetting, straining, and drying steps were conducted to highlight 76% and 42% values for shape fixity and shape recovery, respectively. Furthermore, a foldable box was printed to serve as an example of a self-deployable structure application. The box displayed shape fixity and recovery values of 67% and 26%, respectively, further illustrating significant promise and progress for CNC/TPU nanocomposites in 4D-printed, shape adaptable structures. Further analysis of the effect of degradation during FFF of the CNC/TPU nanocomposite was conducted using rotational rheometry, Fourier-Transform Infrared Spectroscopy (FTIR), and polymer swelling experiments. A temperature ramp from 180 to 270°C showed a significant increase in complex viscosity (h*) at the chosen printing temperatures (240, 250, and 260°C). Moreover, h* of neat TPU suddenly increases at 230°C, indicating a potential chemical crosslinking reaction taking place. 20-minute time sweeps further verified that h* increases along with steady increases in storage (G') and loss (G'') moduli. From these results, it was hypothesized that crosslinking is occurring between CNCs and TPU. Preliminary characterization with FTIR was used to probe the molecular structure of thermally crosslinked samples. At 1060 and 1703 cm-1, there are significant differences in intensities (molecular vibrations) as the temperature increases from 180 to 260°C related to primary alcohol formation and hydrogen bonded carbonyl groups, respectively. The hypothesis is the disassociation of TPU carbamate bonds into soft segments with primary alcohols and hard segments with isocyanate groups. The subsequent increasing peaks at 1060 and 1703 cm-1 may indicate crosslinking of CNCs with these disassociated TPU segments. To quantify potential crosslinking, polymer swelling experiments were implemented. After being submerged in dimethylformamide (DMF) for 24 hours, CNC/TPU samples thermally aged for 15 minutes at 240, 250, and 260°C retained their filament shape and did not dissolve. The 240 and 250°C aged samples had relatively similar crosslink densities close to 900 mole/cm3. However, from 250 to 260°C, there was about a 36% increase in crosslink density. These results suggest that crosslinking is occurring at these printing temperatures because both CNCs and TPU are thermally degrading into reactive components that will lead to covalent crosslinks degradation. Additional characterization is needed to further verify the chemical structure of these CNC/TPU nanocomposites which would provide significant insight for CNC/TPU processing and 3D printing into tunable printed parts with varying degrees of crosslinking. / Master of Science / This thesis is concerned with the development of a processing window for mechanically adaptive cellulose nanocrystal (CNC) and thermoplastic polyurethane (TPU) nanocomposites with fused filament fabrication (FFF) and, evaluating the influence of elevated temperatures on the mechanical, thermal, and rheological properties of said nanocomposite. CNC thermoplastic nanocomposites are a water responsive, mechanically adaptive material that has been gaining interest in additive manufacturing for 4D-printing. Using a desktop 3D-printer, an initial processing window for a 10 wt% CNC in TPU was established with printing temperatures of 240, 250, and 260°C and printing speeds of 600, 1100, and 1600 mm/min. A design of experiments (DOE) was implemented to determine the effects of these parameters on the mechanical properties and mechanical adaptability of printed CNC/TPU parts. Dynamic mechanical analysis (DMA) suggests that combinations of higher temperatures and lower speeds result in reduced storage moduli values for printed CNC/TPU parts. However, mechanical adaptation, or the ability to soften upon water exposure, persists for all the printed samples. Additionally, there was significant discolorations of the printed samples at the higher temperature and slower speed combinations, suggesting thermal degradation is occurring during the printing process. The decrease in storage moduli and discoloration is attributed to thermal energy input, as thermogravimetric analysis indicated thermal degradation was indeed occurring during the printing process regardless of printing temperature. Using the parameters (250°C and 1600 mm/min) that displayed the superior mechanical properties, as well as mechanical adaptivity, shape memory analysis was conducted. The optimal printed part was able to hold 76% of the shape it was strained to, while recovering 42% of the original unstrained shape once immersed in water, indicating potential for shape memory and 4D-printing applications. Furthermore, a foldable box was printed with the optimal parameters and it displayed similar shape memory behavior, illustrating promise for CNC/TPU self-deployable shape adaptable structures. To further study the effect of degradation on the CNC/TPU system, melt flow properties, molecular structure, and polymer swelling were investigated. At the printing temperatures (240, 250, and 260°C), the complex viscosity of the CNC/TPU filament experienced an exponential increase, indicating potential network formation between the CNCs and TPU. Fourier-Transform Infrared Spectroscopy (FTIR) highlighted changes in the molecular structure for the CNC/TPU filament as temperature increased from 240 to 260°C, which suggests that chemical structure changes are occurring because of degradation. The hypothesis is TPU is disassociated into free soft and hard segments that the CNCs can covalently crosslink with, which can potentially be explained by the increases in the FTIR intensities relating to TPU and CNC's chemical structure. To further quantify potential crosslinking between CNCs and TPU, polymer swelling experiments were implemented. The results from these experiments suggest that increasing printing temperatures from 240 to 260°C will lead to higher degrees of crosslinking. Further investigation could yield the validity of this crosslinking and additional optimization of FFF printing with CNC/TPU nanocomposites.

The goal of this research study was to create an artificial annulus fibrosus similar to that of the natural intervertebral disc, as well as find preliminary results for vertebral endplate connection and nucleus pulposus internal pressure, for the correction of disc degeneration in the spine. The three-part composite samples needed to demonstrate good shock absorption and load distribution while maintaining strength and flexibility, and removing the need for metal in the body, something of which no current total disc replacement or spinal fusion surgery can offer. For this study, the spinal disc was separated into its three different components, the annulus fibrosus, the nucleus pulposus, and the vertebral endplates, each playing a vital role in the function of the disc. Two low-cost materials were selected, a Covestro polyurethane and cellulose nanocrystals, for the purpose of creating a polymer composite spinal disc implant. A methodology was established for creating the cast composite material for use as an annulus fibrosus, while also investigating its mechanical properties. The same composite material was used to acquire preliminary results for vertebral endplate connection to the synthesized annulus, however no additional material was used to determine or mimic the mechanical properties of these endplates, due to time constraints. Also because of time constraints, the nucleus used in this study was only comprised of water with no other additives for preliminary testing since the natural nucleus is comprised of about 80-90% water. These properties were then compared to the mechanical properties of the natural disc, so that they could be finely tuned to emulate the natural disc. It is shown in this study that the composite material, when swelled in water, was able to mimic the annulus fibrosus in tensile strength and modulus, however showed higher compressive strength and modulus than ideal. The samples also did not undergo any permanent deformation within the realm of force actually introduced to the natural disc. The vertebral endplates showed decent adhesion to the synthesized annulus, however there were slight defects that became failure concentrators during compression testing. The nucleus showed promising results maintaining good internal pressure to the system causing better compressive load distribution, with barreling of the samples. / Master of Science / Spinal disc degeneration is a very prevalent problem in today’s society, effecting anywhere from 12% to 35% of a given population. It usually occurs in the lumbar section of the spine, and when severe enough, can cause bulging and herniation of the intervertebral disc itself. This can cause immense lower back pain in individual’s stricken with this disease, and in the US, medical costs associated with lower back pain to exceed $100 billion. Current solutions to this problem include multiple different treatment options of which, spinal fusion surgery and total disc replacement (TDR) are among the most common. Although these treatments cause pain relief for the majority of patients, there are multiple challenges that come with these options. For example, spinal fusion surgery severely limits the mobility of its patients by fusing two vertebrae together, disallowing any individual movement, and TDR can cause hypermobility in among the vertebrae and offer little to no shock absorption of loads. Therefore, a better treatment option is needed to relieve the pain of the patients, as well as maintain equal motion, shock absorption, and load cushioning to that of the normal intervertebral disc and remaining biocompatible. The goal of this research study was to create a three-component system, like that of the natural intervertebral disc, for the use of spinal disc replacement and to replace current options. The fabricated system was comprised of the three components found in the natural intervertebral disc; the annulus fibrosus, the nucleus pulposus, and the vertebral endplates. Because the system will need to go in-body, the materials used were all characterized as biocompatible materials; the polyurethane currently being used in medical devices and implants, and the cellulose nanocrystals (CNCs) coming from natural cellulose in sources such as wood and plants. The results determined that the mechanical properties of the system can be fine-tuned in order to mimic the natural strength and cushioning capabilities of the natural disc, based on CNC content added to the polyurethane, and when all three components of the system are added together, the compressive stress-strain is most similar to the natural disc in compression. However, the system did show failure in the connection between the annulus fibrosus and vertebral endplates, causing herniation of the nucleus similar to the initial problem attempting to be solved. For this, more ideal fabrication methods should be researched in the future including 3D printing techniques, injection molding, and roll milling. As well as alternate fabrication techniques, cell grow and viability should be determined to show that cells don’t die once the system in implanted.

The purpose of this research was to determine the effects of cellulose nanocrystals (CNCs), as potential additives, on the properties and performance of phenol–formaldehyde (PF) adhesive resin. The steady-state viscosity of a commercial PF resol resin and three CNC–resin mixtures, containing 1–3 wt % CNCs, based on solids content, was measured with a rheometer as a function of shear rate. The viscosity of the PF resin itself was independent of shear rate. The viscosity–shear rate curves of the CNC–resin mixtures showed two regions, a shear thinning region at lower shear rates and a Newtonian region at higher shear rates. The low-shear-rate viscosity of the resin was greatly increased by the CNCs. The structure of the CNC–resin mixtures under quiescent conditions was analyzed by polarized light microscopy. The mixtures contained CNC aggregates, which could be disrupted by ultrasound treatment. The curing progressions of the resin and CNC–resin mixtures were analyzed by non-isothermal differential scanning calorimetry (DSC). The DSC curves showed two exotherms followed by an endotherm. The energy of activation for the first exotherm was reduced by the CNCs whereas the energy of activation for the second exotherm was not affected by the CNCs. Increasing CNC contents caused higher degrees of reaction conversion during the first curing stage and a greater loss of sample mass, attributed to formaldehyde release during resin cure. For analysis of the mechanical properties during and after cure, sandwich-type test specimens were prepared from southern yellow pine strips and the resin and CNC–resin mixtures. The mechanical properties of the test specimens were measured as a function of time and temperature by dynamic mechanical analysis (DMA). The time to incipient storage modulus increase decreased and the rate of relative storage modulus increase increased with increasing CNC content. The ultimate sample stiffness increased with increasing CNC content for CNC contents between 0 and 2 wt %, which was attributed to mechanical reinforcement of the resin by the CNCs. At a CNC content of 3 wt %, the ultimate sample stiffness was lower than at a CNC content of 2 wt % and the second tan δ maximum occurred earlier in the experiment, indicating an earlier onset of vitrification. The lower ultimate sample stiffness was attributed to premature quenching of the curing reactions through CNC-induced depression of the vitrification point. For analysis of the fracture performance, double cantilever beam test specimens were prepared from southern yellow pine beams and the resin and CNC–resin mixtures, using different hot-pressing times. Fracture energies were measured by mode I cleavage tests. Bondline characteristics were analyzed by light microscopy. At a hot-pressing time of 10 min, the fracture energy decreased with increasing CNC content, whereas it stayed constant for CNC contents between 1 and 3 wt % at a hot-pressing time of 8 min. The bondlines of resin mixtures containing CNCs exhibited voids, whereas those of the pure resin did not. CNCs had both benefitial and detrimental effects on the properties and performace of PF resin. / Master of Science

Ultra-fine grained materials with sub-micrometer grain size exhibit superior mechanical properties when compared with conventional fine-grained material as well as coarse-grained materials. Severe plastic deformation (SPD) techniques have been shown to be an effective way to modify the microstructure in order to improve the mechanical properties of the material. Crystalline materials require dislocations to accommodate plastic strain gradients and maintain lattice continuity. The lattice curvature exists due to the net dislocation that left behind in material during deformation. The characterization of such defects is important to understand deformation accumulation and the resulting mechanical properties of such materials. However, traditional techniques are limited. For example, the spatial resolution of EBSD is insufficient to study materials processed via SPD, while high dislocation densities make interpretations difficult using conventional diffraction contrast techniques in the TEM. A new technique, precession electron diffraction (PED) has gained recognition in the TEM community to solve the local crystallography, including both phase and orientation, of nanocrystalline structures under quasi-kinematical conditions. With the assistant of precession electron diffraction coupled ASTARÔ, the structure evolution of equal channel angular pressing processed commercial pure titanium is studied; this technique is also extended to two-phase titanium alloy (Ti-5553) to investigate the existence of anisotropic deformation behavior of the constituent alpha and beta phases.