Yes / In order to improve the efficiency of the structural lateral resistance system, a new type of Grid tubular-Double Steel Plate (GDSP) concrete composite shear walls is proposed and investigated in this paper. Six test specimens, namely one reinforced concrete (RC) shear wall, three GDSP concrete composite shear walls, one concrete-filled steel tube (CFST) frame, one CFST frame and GDSP concrete composite shear wall combined system were physically tested to failure. The seismic performance of the six test specimens, including hysteresis behavior, ductility, energy dissipation, degradation of stiffness and strength, are recorded and compared. The results show that the GDSP concrete composite shear walls exhibited typical bending failure under low reversed cycle loading, achieving good seismic performance with full hysteresis curve, high bearing capacity, excellent ductility, slow degradation of stiffness and bearing capacity. Under the same axial compression ratio, the yield load of GDSP concrete composite shear wall was about 2.73 times, whilst the peak load was 3.23 times, respectively, of those of RC shear wall. On the other hand, the peak displacement of GDSP concrete composite shear wall was 5 times while ultimate displacement was 3.86 times, respectively, of those of RC shear wall. For GDSP concrete composite shear walls, with the increase of axial compression ratio, the peak load of the new types of concrete composite shear wall increases, but the ductility decreases, gradually. The CFST frame and GDSP concrete composite shear wall can work together co-ordinately. The hysteretic curve of the combined system is fuller, the ductility is improved, the degradation of stiffness and strength are slow when compared with GDSP concrete composite shear wall. Under reversed cyclic loading, the GDSP concrete composite shear wall exhibits low stiffness degradation characteristics and excellent fatigue resistance. / The authors would like to acknowledge the financial support to the work by the Natural Science Foundation of Jiangsu Province, China (BK20201436), the Open Foundation of Jiangsu Province Engineering Research Center of Prefabricated Building and Intelligent Construction (2021), the Science and Technology Project of Jiangsu Construction System (2018ZD047, 2021ZD06), the Science and Technology Project of Gansu Construction System (JK2021-19), the Science and Technology Cooperation Fund Project of Yangzhou City and Yangzhou University (YZU212105), the Science and Technology Innovation Fund of Yangzhou University (2020-65) and the Blue Project Youth Academic Leader of Colleges and Universities in Jiangsu Province (2020).

Yes / In order to promote the utilization of high strength materials and application of prefabricated structures, flexural behaviour of section steel-precast UHPC (Ultra-High performance concrete) slab composite beams prefabricated with bolt shear connectors are numerically simulated by the finite element (FE) software ABAQUS. The model is verified by three prefabricated steel-concrete composite beams tested. Numerical analysis results are in good accordance with experimental results. Furthermore, parametric studies are conducted to investigate the effects of strength of section steel and concrete of precast slab, thickness of section steel, width and height of precast concrete slab, diameters of steel bars and bolt shear connectors. The flexural behaviour of composite beams, in terms of bearing capacity, deflection, ductility and energy dissipation, are compared. The numerical results indicate that the improvement of strength of section steel results in a decrease of ductility, but a significant increase of the ultimate load and energy dissipation. Compared with composite beam made of section steel with thickness of 10 mm, the ultimate load of beams made of section steel with thickness of 14 and 18 mm improve by 29.0% and 58.8%, respectively, the ductility enhance by 2.8% and 8.3%, respectively, and the energy dissipation improve by 8.0% and 12.3%, respectively. With the increase of concrete strength, the ultimate load, deflection and energy dissipation gradually increase. The ductility of steel-UHPC composite beam is the highest, that of steel-HSC composite beam is the lowest. The effect of reinforcement ratio of concrete slab and diameter of shear bolts on the ultimate load of composite beam is limited. Simplified formulae for two different sectional types of proper-reinforced section steel-precast UHPC slab composite beams occurred bending failure are proposed, and the predicted results fit well with the simulated results. The results can be taken as a reference for the design and construction of section steel-precast UHPC slab composite beams.

Shallow foundations are widely used in different types of soils for supporting the loads from the lightly loaded superstructures of various civil infrastructures both on level and sloping ground. Design of shallow foundations in geotechnical engineering practice is widely based on the principles of saturated soil mechanics because they are relatively simple. However, the soil near the ground surface (i.e., vadose zone) in which the shallow foundations are typically placed is in an unsaturated state. The water content variation in unsaturated soils is influenced by hydrological events such as the snow melt, rainfall infiltration, evaporation, and the plant transpiration. Due to this reason, the hydro-mechanical properties (i.e., coefficient of permeability, shear strength and volume change) of unsaturated soils are sensitive to the variation in soil suction associated with water content changes. These properties in turn have a significant impact on the bearing capacity and settlement behavior of the shallow foundations. Therefore, it is rational to investigate shallow foundations’ behavior extending the principles of unsaturated soil mechanics. During the last two decades, there has been a significant interest towards investigating shallow foundations based on unsaturated soil mechanics. Laboratory, field, and model studies highlight that matric suction variation in unsaturated soils has a significant influence on the bearing capacity and settlement behavior of shallow foundations. However, the focus of most of the presently available studies in the literature consider mostly vertical loading conditions on level soil ground. There are limited studies related to the design of shallow foundations on sloping ground and subjected to inclined and eccentric loading conditions. Also, there are only few studies that consider the effect of the steady state and transient flow conditions on the foundation bearing capacity evaluation. Therefore, one of the key objectives of this thesis is directed toward developing rational tools for investigating shallow foundations considering the steady state and transient flow conditions associated with water infiltration and evaporation in unsaturated soils. Comprehensive investigation studies are undertaken to interpret the influence of the steady state and transient flow conditions on the shallow foundations related to: (i) bearing capacity on the sloping ground in different types of soils including expansive soils, and (ii) bearing capacity under the inclined and eccentric loading conditions with homogeneous soil properties and considering spatial variation of soil properties. Succinct details related to investigated studies are summarized below: (1) An analytical method is proposed for quantifying the bearing capacity of the shallow foundations on unsaturated soil slopes considering different rainfall infiltration conditions. The proposed method is a novel tool for considering the simultaneous influence of several parameters that include the flow rates, the infiltration duration, the foundation set-back distance and the ground water table depth on the foundation bearing capacity. (2) Another analytical method is proposed for evaluating the foundation bearing capacity under inclined and eccentric loading considering both the steady state and transient flow conditions. Semi-empirical equations are proposed for describing the failure envelops in vertical and horizontal (V - H) loading space and in the vertical and moment (V - M) loading space. These equations are capable to describe the variation of failure envelops considering the influence of the groundwater table depth variation, internal friction angles, surface flux boundary conditions and different infiltration durations. (3) The influence of infiltration on the combined performance of both the foundation and the slope in cracked expansive soils is evaluated with the aid of a numerical technique. A semi-empirical model that describes the elastic modulus and the matric suction is implemented into the numerical model. Bimodal soil water characteristic curve is used as a tool for understanding the influence of surface cracks in the numerical study in a simplified manner. The influence of the rainfall intensity, rainfall duration, foundation setback distance and foundation loading on the combined performance of foundation and slope were investigated. Results combined with some suggestions for rational design procedures are presented that can be useful for geotechnical engineers in practice applications. (4) Numerical analyses are conducted for shallow foundations under vertical and combined loading subjected to different flow conditions. A numerical code procedure is exclusively developed as a part of this study to: (i) consider the variation of soil properties along with the matric suction fluctuations in the commercial software ABAQUS with the aid of a user developed subroutine USDFLD; (ii) incorporate the spatial variability of soil properties into the finite element model. Comparisons are provided between the numerical study and other methods such as the experimental investigations, the analytical methods, and the semi-empirical equations for bearing capacity failure envelopes. In addition, comparisons are also made between the failure envelopes and the failure mechanisms contour using the model considering soil spatial variability and homogeneous soil properties. The proposed methods in this thesis are simple to use for evaluating bearing capacity of shallow foundations that are subjected to steady state and transient state flow conditions considering two scenarios: (i) foundation on sloping ground (ii) foundation under inclined and eccentric loading. The results from the above studies reveal that it is the relationship between the soil permeability and the rainfall characteristics that mainly control the water infiltration rates. The soil suction and the effective degree of saturation are influenced by the water infiltration rates and have a significant impact on the foundation as well as the slope behavior. More importantly, the investigations undertaken in this thesis contribute towards addressing the research gaps related to the behavior of foundations in unsaturated soils. Various scenarios considered in this thesis include the influence of unsaturated flow have not been considered earlier in the literature. The results of the studies summarized in this thesis are expected to be useful for practicing geotechnical engineers in the optimal design of shallow foundations extending the principles of unsaturated soil mechanics for various soils. Moreover, the proposed methods can be used for interpreting the foundation behavior for their entire life span service. In addition, these methods can be employed to rationally explain the field-measured data and can also be used in the forensics analyses of failed slopes and shallow foundations.

We study numerical methods for solving the nonlinear porous medium and Navier-Lame problems. When coupled together, these equations model the flow of exhaust through a porous medium, soil, and the effects that the pressure has on the soil in terms of spatial displacement. For the porous medium equation we use the Crank-Nicolson time stepping method with a spectral discretization in space. Since the Navier-Lame equation is a boundary value problem, it is solved using a finite element method where the spatial domain is represented by a triangulation of discrete points. The two problems are coupled by using approximations of solutions to the porous medium equation to define the forcing term in the Navier-Lame equation. The spatial displacement solutions can be used to approximate the strain and stress imposed on the soil. An analysis of these physical properties shows whether or not the material ceases to act as an elastic material and instead behaves like a plastic which will tell us if the soil has failed and a crater has formed. Analytical as well as experimental tests are used to find a good balance for solving the porous medium and Navier-Lame equations both accurately and efficiently.

No description available.

Quarry fines are by-products of the aggregate extraction and productionprocesses. Because such fine material cannot be marketed, it becomes aburden for the aggregate industry, resulting in stockpiles of financiallyunexploited material. Even though previous research has been focused onminimizing the generation of quarry fines, far too little attention has beenpaid to maximizing their utilization instead. The aim of this thesis is toinvestigate whether 0/2 mm and 0/4 mm quarry fines can be utilized asalternative materials in the construction industry, specifically in theunbound layer of a road or as filling against a bridge. The methodologyconsisted of four laboratory tests that investigated the water content,particle size distribution and percentage of filler content, optimummoisture content (OMC) and maximum dry density (MDD) relationshipas well as bearing capacity of the materials. The results show that theamount of filler content (<0.063 mm) can significantly impact thematerial’s water-holding capacity as well as its compaction capabilities.After comparing the bearing capacity measurements to the technicalrequirements of the Swedish Transport Administration, it was found thatthe 0/2 mm fits the necessary requirements for use in the unbound layerof either a flexible or rigid pavement but not as filling against a bridge.Further research is needed to determine the material’s relationship towater absorption and resistance to freezing and thawing cycles, as it isdifficult to assess its suitability for road construction solely on theseresults; however, despite its limitations, the study provides some valuableinsights into the potential applications of quarry fines.

Yes / To investigate the flexural performance of steel-UHPC (ultra-high performance concrete) composite beams with welded steel shear keys (SSK), eight specimens were experimental studied by four-point bending test. The finite element (FE) models were established based on the experimental results, then, the failure mode, load, deflection, strain and relative interface slip were parametric analyzed. The influences of strength, dimensions and configuration of upper concrete slab, steel beams as well as SSK on flexural performance, in terms of load-deflection response, ductility and ultimate energy dissipation, were studied. The experimental results show that steel-UHPC composite beams have superior bearing capacity, deformation capacity, ductility and energy dissipation ability when compared with steel-NSC (normal strength concrete) composite counterparts. Increasing the height of upper concrete slab has a significant effect on improving bending capacity and flexural stiffness, while increasing the width has a significant effect on enhancing deformation, ductility and ultimate energy dissipation. Increasing the yield strength, thickness of web and flange of steel beams has significant effect on improving bending capacity. Reducing the SSK spacing or increasing the yield strength of SSK, height and thickness slightly improve the cracking, yield and ultimate loads, reduce deflections, enhance the flexural stiffness, slightly weakens the ductility and ultimate energy dissipation. Besides, four types of failure modes were defined, based on reasonable assumptions, formulae for bearing capacity were proposed, and the predicted results fit well with experimental results. The results can be taken as reference for the design and application of steel-UHPC composite beams in long-span and heavy-load structures. / The authors would like to acknowledge the financial support to the work by the Natural Science Foundation of Jiangsu Province, China (BK20201436), High-End Foreign Experts Project of Ministry of Science and Technology, China (G2022014054L), Science and Technology Project of Jiangsu Construction System (2021ZD06, 2018ZD047), Science and Technology Cooperation Fund Project of Yangzhou City and Yangzhou University (YZU212105, YZ2022194), Science and Technology Project of Yangzhou Construction System (202309, 202312, 202204). / The full text of this article will be released for public view at the end of the publisher embargo on 11th Aug 2024.

With advances in modern technology, satellite-based data is rapidly becoming a viable option for geotechnical site characterization. Commercial satellite data offers high resolution (~25-200 cm), increased spatial coverage on the order of kilometers, short revisit times leading to high temporal coverage, and allows for data to be analyzed rapidly and remotely without the need for physical site access. These advantages are particularly attractive for characterizing coastal sites, where both the strength properties and moisture content can change rapidly in response to tidal stages, wave runup, and storm events. To date, there have been limited investigations into the use of satellite-based data for characterizing geotechnical properties of sandy beach sediments. Furthermore, the use of these moisture contents to estimate the soil strength of beaches has been limited. The goal of this research was to develop pathways to estimate the moisture content of sandy beach sites utilizing satellite-based data. For this study, both optical and synthetic aperture radar (SAR) images were collected at two sites: the Atlantic beach near the US Army Corps of Engineers Field Research Facility in Duck, North Carolina and three distinct sites located near Yakutat, Alaska (Cannon Beach, Ocean Cape, and Point Carrew). During satellite overflight, ground measurements of moisture content, grain size, unit weight, porosity, and bearing capacity were collected. Using the field measurements, this research (1) developed a framework to estimate the moisture content of sandy beach sediments from satellite-based optical images; (2) investigated the necessary collection parameters to estimate the moisture content from SAR images; and (3) developed a framework to estimate the bearing capacity of sandy beaches using moisture contents derived from satellite-based images. The results of this study demonstrated that optical images can produce reasonable estimates of the moisture content when compared to field measurements and are strongly influenced by local morphology. Additionally, SAR images with incidence angles of 30°-50° produced the best results when compared to field measurements. Finally, using the spatial estimates moisture content produced from satellite data and standard sediment, maps of bearing capacity can be developed to predict beach trafficability. / Doctor of Philosophy / The strength of sandy beaches is impacted by the density, particle size and shape, distribution of grain sizes, mineralogy, and moisture content. For coastal sites, which typically have a dominant mineralogy and a limited range of grain sizes, a main factor changing is the moisture content. This varying moisture content can result in the increase or decrease in soil strength, and impacts modelling for coastal challenges such as erosion or beach trafficability (i.e., the ability to drive on the beach) on large scales. It is common to measure moisture content through sampling or moisture probes, but these represent point measurements and may not accurately capture the spatial and temporal moisture contents at a beach. Recently, satellite-based images have become popular for assessing processes and environmental changes over large areas. However, their use for mapping moisture content at sandy beaches has been limited, and the proper models are unknown. As such, the goal of this research is to investigate the use of satellite images to map moisture content over large areas. For this study, measurements were conducted at two sites: an Atlantic beach located near the US Army Corps of Engineers Field Research Facility in Duck, North Carolina and three distinct sites located near Yakutat, Alaska (Cannon Beach, Ocean Cape, and Point Carrew). Simultaneously with ground measurements, two different types of images were collected. The first, optical data, collects data over the visible (400-700 nm) and near infrared (700-1300 nm) regions of the electromagnetic spectrum. These satellites use the sun to light the scene and the amount of energy reflected back to the satellite is used to estimate the moisture content. The second, X-band synthetic aperture radar (SAR) data (wavelengths of 3.1 cm), sends its own energy source to the ground and uses the returned energy to estimate the moisture content. Both optical and SAR are able to produce reasonable estimates of moisture content when compared to field measurements. These estimated values of moisture content are then tested in a model to estimate the sand strength, with those estimated values also following the expected trends. Ultimately, this work can be used to contribute to understanding how moisture content varies at sandy beaches and improve trafficability predictions in sandy beach environments.

Over the past 50 years, several advancements have been made in the research area of the mechanics of unsaturated soils. These advancements can be categorized into two groups; (i) development (or improvement) of testing techniques (or apparatus) to determine the mechanical properties of unsaturated soils and (ii) development of (numerical, empirical or semi-empirical) models to estimate the variation of mechanical properties of unsaturated soils with respect to suction based on the experimental results. Implementation of the mechanics of unsaturated soils in conventional geotechnical engineering practice, however, has been rather limited. The key reasons for the limited practical applications may be attributed to the lack of simple and reliable methods for (i) measuring soil suction in the field quickly and reliably and (ii) estimating the variation of mechanical properties of unsaturated soils with respect to suction. The main objective of this thesis research is to develop simple and reliable techniques, models or approaches that can be used in geotechnical engineering practice to estimate sol suction and the mechanical properties of unsaturated soils. This research can be categorized into three parts. In the First Part, simple techniques are proposed to estimate the suction values of as-compacted unsaturated fine-grained soils using a pocket penetrometer and a conventional tensiometer. The suction values less than 300 kPa can be estimated using a strong relationship between the compressive strength measured using a pocket penetrometer and matric suction value. The high suction values in the range of 1,200 kPa to 60,000 kPa can be estimated using the unique relationship between the initial tangent of conventional tensiometer response versus time behavior and suction value. In the Second Part, approaches or semi-empirical models are proposed to estimate the variation of mechanical properties of unsaturated soils with respect to suction, which include: - Bearing capacity of unsaturated fine-grained soils - Variation of bearing capacity of unsaturated fine-grained soils with respect to matric suction - Variation of initial tangent elastic modulus of unsaturated soils below shallow foundations with respect to matric suction - Variation of maximum shear modulus with respect to matric suction for unsaturated non-plastic sandy soils (i.e. plasticity index, Ip = 0 %) In the Third Part, approaches (or methodologies) are suggested to simulate the vertically applied stress versus surface settlement behavior of shallow foundations in unsaturated coarse-grained soils assuming elastic-perfectly plastic behavior. These methodologies are extended to simulate the stress versus settlement behavior of both model footings and in-situ plates in unsaturated coarse-grained soils. The results show that there is a reasonably good comparison between the measured values (i.e. soil suction, bearing capacity, elastic and shear modulus) and those estimated using the techniques or models proposed in this thesis research. The models (or methodologies) proposed in this thesis research are promising and encouraging for modeling studies and practicing engineers to estimate the variation of mechanical behavior of unsaturated soils with respect to matric suction.

The objective of this thesis was to advance understanding in the field of biolubrication, finding inspiration from the human synovial joints. This was addressed by investigating the association of key biolubricants and the resulting lubrication performance. Techniques employed during the course of this work were Atomic force microscopy (AFM), Quartz crystal microbalance with dissipation monitoring (QCM-D), X-ray reflectivity (XRR). Key synovial fluid and cartilage components like dipalmitoylphosphatidylcholine (DPPC), hyaluronan (HA), lubricin, and cartilage oligomeric matrix protein (COMP) have been used in the investigations. Focus was towards two lubrication couples; DPPC-hyaluronan and COMP-lubricin. DPPC-hyaluronan mixtures were probed on hydrophilic silica surfaces and COMP-lubricin association structures were explored on weakly hydrophobic poly (methyl methacrylate) (PMMA) surfaces. Investigations of the COMP-lubricin pair revealed that individually these components are unable to reach desired lubrication. However in combination, COMP facilitates firm attachment of lubricin to the PMMA surface in a favourable confirmation that imparts low friction coefficient. DPPC and hyaluronan combined impart lubrication advantage over lone DPPC bilayers. Hyaluronan provides a reservoir of DPPC on the surface and consequently self-healing ability. Other factors like temperature, presence of calcium ions, molecular weight of hyaluronan, and pressure were also explored. DPPC bilayers at higher temperature had higher load bearing capacity. Association between DPPC Langmuir layers and hyaluronan was enhanced in the presence of calcium ions, and lower molecular weight hyaluronan had a stronger tendency to bind to DPPC. At high pressures, DPPC-hyaluronan layers were more stable compared to lone DPPC bilayers. / <p>QC 20170210</p>