Thesis (M.S.)--State University of New York at Binghamton, Thomas J. Watson School of Engfineering and Applied Science, Department of Systems Science and Industrial Engineering, 2009. / Includes bibliographical references.

This dissertation focuses on high-performance LC-tank CMOS VCO design at 2 GHz. The high-Q inductors are realized using wiring metal lines in advanced packages. Those inductors are used in the resonator of the VCO to achieve low phase noise, low power consumption, and a wide frequency tuning range. In this dissertation, a fine-pitch ball-grid array (FBGA) package, a multichip module (MCM)-L package, and a wafer-level package (WLP) are incorporated to realize the high-Q inductor. The Q-factors of inductors embedded in packages are compared to those of inductors monolithically integrated on Si and GaAs substrates. All the inductors are modeled with a physical, simple, equivalent two-port model for the VCO design as well as for phase noise analysis. The losses in an LC-tank are analyzed from the phase noise perspective. For the implementation of VCOs, the effects of the interconnection between the embedded inductor and the VCO circuit are investigated. The VCO using the on-chip inductors is designed as a reference. The performance of VCOs using the embedded inductor in a FBGA and a WLP is compared with that of a VCO using the on-chip inductor. The VCO design is optimized from the high-Q perspective to enhance performance. Through this optimization, less phase noise, lower power consumption, and a wider frequency tuning range are obtained simultaneously.

La technologie flip chip est de plus en plus répandue dans l'industrie électronique [trois dimensions (3D) System in Package] et est principalement utilisée pour la fabrication de réseaux détecteurs de grand format (mégapixels) et faible pas. Pour étudier la fiabilité de ces assemblages, des simulations numériques basées sur des méthodes d'éléments finis semblent être l'approche la moins chère. Cependant, de très grands assemblages contiennent plus d'un million de billes de brasure, et le processus d'optimisation de ces structures par des simulations numériques se révèle être une tâche très fastidieuse. Dans de nombreuses applications, la couche d'interconnexion de tels assemblages flip chip se compose de microbilles de brasure noyées dans de l'époxy. Pour ces configurations, nous proposons une approche alternative, qui consiste à remplacer cette couche d'interconnexion hétérogène par un matériau homogène équivalent (MHE). Un modèle micromécanique pour l'estimation de ses propriétés thermoélastiques équivalentes a été mis au point. La loi de comportement obtenue pour le MHE a ensuite été implémentée dans le logiciel par éléments finis (Abaqus®). Les propriétés élastiques des matériaux de l'assemblage sont définies par la littérature et également déterminées expérimentalement par une méthode de caractérisation mécanique : la nano-indentation. Les réponses thermomécaniques des assemblages testés soumis à des chargements correspondant aux conditions de fabrication ont été analysées. La technique d'homogénéisation-localisation a permis d'estimer les valeurs moyennes des contraintes et des déformations dans chaque phase de la couche d'interconnexion. Pour accéder plus précisément aux champs de contraintes et déformations dans ces phases, deux modèles de zoom structurel (couplage de modèles et submodeling), en tenant compte de la géométrie réelle de la bille de brasure, ont été testés. Les champs de contrainte et de déformation locaux obtenus corroborent avec les initiations de dommage observées expérimentalement sur les billes de brasure / Flip chip technology is increasingly prevalent in electronics assembly [threedimensional (3D) system in package] and is mainly used at fine pitch for manufacture of megapixel large focal-plane detector arrays. To estimate the reliability of these assemblies, numerical simulations based on finite-element methods appear to be the cheapest approach. However, very large assemblies contain more than one million solder bumps, and the optimization process of such structures through numerical simulations turns out to be a very time-consuming task. In many applications, the interconnection layer of such flip-chip assemblies consists of solder bumps embedded in epoxy filler. For such configurations, we propose an alternative approach, which consists in replacing this heterogeneous interconnection layer by a homogeneous equivalent material (HEM). A micromechanical model for the estimation of its equivalent thermoelastic properties has been developed. The constitutive law of the HEM obtained was then implemented in finite-element software (Abaqus®). Elastic properties of materials that compose the assembly were found in literature and by using mechanical characterization method especially nano-indentation. Thermomechanical responses of tested assemblies submitted to loads corresponding to manufacturing conditions have been analyzed. The homogenization-localization process allowed estimation of the mean values of stresses and strains in each phase of the interconnection layer. To access more precisely to the stress and strain fields in these phases, two models of structural zoom (model coupling and submodeling), taking into account the real solder bump geometry, have been tested. The local stress and strain fields obtained corroborate the experimentally damage initiation of the solder bumps observed

Graduation thesis is specialized on dilemma of the integrated circuits with ball grid array. Chapter two describes several types of packages and confrontation of their characteristics. Chapter three considers possibilities of corrections these boards bedded with packages, mounting and demounting of these packages, method of camera control and also inspection of the soldering process. Chapter four attend to practical measuring of thermal profiles and their optimalization.

This thesis is focused on BGA packages and fault detection after rework using X – Ray. There is a description of BGA packages by carrier substrate, techniques of connecting on chip, from mounting packages to repair printed circuit boards (hereafter PCB). Thesis summarizes description of defects, which are created after rework process. There is also description of X – Ray as method for analyzing defects. X – PLANE method used to detect internal structure of BGA packages and it was confirmed by microsection and by software for reconstruction. Description of automatic and manual measurement is follow.

This diploma thesis is focused on detecting of defects on BGA (Ball Grid Array) components using of X-ray. Defects are formed during reflow BGA components during assembly, but also later due to mechanical and thermal stress. Therefore, there is an overview of defects and methods of diagnosis of BGA packages eg .: modern X-ray defect detection or micro sections. There is disclosed a device NORDSON DAGE XD7600NT its operation and setup. The device enables advanced methods of scanning called X-plane. For creating 3D models used reconstructive software called CERA, which uses raw data from the method of X-Plane.