We have investigated the impact of strain on the incorporation and the properties of extended and point defects in (Mg,Zn)O thin films by means of photoluminescence, X-ray diffraction, deep-level transient spectroscopy (DLTS), and deep-level optical spectroscopy. The recombination line Y2, previously detected in ZnO thin films grown on an Al-doped ZnO buffer layer and attributed to tensile strain, was exclusively found in (Mg,Zn)O samples being under tensile strain and is absent in relaxed or compressively strained thin films. Furthermore a structural defect E3′ can be detected via DLTS measurements and is only incorporated in tensile strained samples. Finally it is shown that the omnipresent deep-level E3 in ZnO can only be optically recharged in relaxed ZnO samples.

The sun provides us with a surplus of energy convertible to electricity using solar cells. This thesis focuses on solar cells based on chalcopyrite (CIGSe) as well as kesterite (CZTS(e)) absorber layers. These materials yield record efficiencies of 20.4 % and 11.1 %, respectively. Especially for CZTS(e), the absorber layers often do not consist of one single desired phase but can exhibit areas with deviating material properties, referred to as secondary phases. Furthermore, several material layers are required for a working solar cell, each exhibiting interfaces. Even though secondary phases and interfaces represent a very small fraction of the solar cell they can have a profound influence on the over-all electrical solar cell characteristics. As such, it is crucial to understand how secondary phases and interfaces influence the local electrical characteristics. Characterising secondary phases and interfaces is challenging due to their small sample volume and relatively small differences in composition amongst others. This is where electronmicroscopy, especially transmission electron microscopy, offers valuable insight to material properties on the microscopic scale. The main challenge is, however, to link these material properties to the corresponding electrical characteristics of a solar cell. This thesis uses electron beam induced current imaging and introduces a new method for JV characterisation of solar cells on the micron scale. Combining microscopic structural and electrical characterisation techniques allowed identifying and characterising local defects found in the absorber layer of CIGS solar cells after thermal treatment. Furthermore, CZTSe solar cells in this thesis exhibited a low photo-current density which is traced to the formation of a current blocking ZnSe secondary phase at the front contact interface. The electron microscopy work has contributed to an understanding of the chemical stability of CZTS and has shown the need for an optimised back contact interface in order to avoid chemical decomposition reactions and formation of detrimental secondary phases. With this additional knowledge, a comprehensive picture of the material properties from the macroscopic down to the microscopic level can be attained throughout all required material layers.

A variety of benefits motivate the development of epitaxial metals, among which include the ability to design fully integrated layer structures where metallic films and nanostructures can be embedded into the cores of optoelectronic devices. Applications include high-performance tunnel-junctions, epitaxial transparent Ohmic contacts, photomixer material, and thermoelectrics. Additionally, the integration of metallic nanostructures and films into optoelectronic devices has shown potential for improving device performance and functionality through sub-wavelength confinement of plasmonic modes and enhancement of light/matter interactions. The rare-earth monopnictide (RE-V) material system can be integrated epitaxially with conventional zincblende III-V substrates under normal growth conditions, resulting in high-quality, thermodynamically stable interfaces. The RE-V semimetals span a range of optical, electrical, and structural properties, making them ideal for integration into III-V-based optoelectronic devices and applications. In this dissertation, high-quality epitaxial LuAs, LaAs and La(x)Lu(1-x)As films and nanostructures were grown and characterized for their structural, electrical, optical, and plasmonic properties. Through a sweep of alloy film compositions of the RE-V alloy material La(x)Lu(1-x)As, the ability to produce tunable epitaxial metals was demonstrated, with a range of peak transmission spectra from near- to mid-infrared wavelengths, plasmonic response in the mid-infrared, moderate resistivity, and lattice-matching potential to many relevant III-V substrates. Additionally, there is a great deal of interest in developing techniques to produce optoelectronic devices that are not restricted by substrate lattice constant. Many epitaxial approaches have been tried, with moderate success; however, growing low defect-density heteroepitaxial materials with differing crystal structures and highly-mismatched lattice parameters is extremely challenging, and such structures suffer from poor thermal properties and reliability issues. A general approach is needed for thin metamorphic buffer layers with minimal threading dislocations that simultaneously have low thermal resistance for effective heat-sinking and device reliability. An investigation was conducted into the use of RE-V nanostructure superlattices towards the reduction of dislocation density in highly-mismatched III-V systems. / text

A deeper understanding of Cu(In,Ga)Se2 (CIGS) solar cells is important for the further improvement of these devices. This thesis is focused on the use of electrical modelling as a tool for pursuing this aim. Finished devices and individual layers are characterized and the acquired data are used as input in the simulations. Band gap gradients are accounted for when modelling the devices. The thesis is divided into two main parts. One part that treats the influence of cadmium free buffer layers, mainly atomic layer deposited (Zn,Mg)O, on devices and another part in which the result of CIGS absorber layer modifications is studied. Recombination analysis indicates that interface recombination is limitting the open circuit voltage (Voc) in cells with ZnO buffer layers. This recombination path becomes less important when magnesium is introduced into the ZnO giving a positive conduction band offset (CBO) towards the CIGS absorber layer. Light induced persistent photoconductivity (PPC) is demonstrated in (Zn,Mg)O thin films. Device modelling shows that the measured PPC, coupled with a high density of acceptors in the buffer-absorber interface region, can explain light induced metastable efficiency improvement in CIGS solar cells with (Zn,Mg)O buffer layers. It is shown that a thin indium rich layer closest to the buffer does not give any significant impact on the performance of devices dominated by recombination in the CIGS layer. In our cells with CdS buffer the diffusion length in the CIGS layer is the main limitting factor. A thinner CIGS layer improves Voc by reducing recombination. However, for thin enough absorber layers Voc deteriorates due to recombination at the back contact. Interface recombination is a problem in thin devices with Zn(O,S) buffer layers. This recombination path is overshadowed in cells of standard thickness by recombination in the CIGS bulk. Thin cells with Zn(O,S) buffer layers have a higher efficiency than CdS cells with the same absorber thickness.

Parmi les différentes cellules photovoltaïques existantes, les technologies à base de CIGS représentent aujourd'hui une alternative sérieuse à celles basées sur le silicium. De même, les technologies organiques émergent en vue d'applications sur le marché de la faible puissance. Afin d'être parfaitement concurrentielle, ces cellules doivent s'affranchir au maximum de la présence d'indium (surcoût) au sein de leurs structures (TCO, couche absorbante), ou de matériaux toxiques comme le CdS utilisé en tant que couche tampon. Les chalcogénures de zinc tels que le Zn1-xMgxO ou le ZnOzS1-z peuvent être employées à la place du CdS grâce à leurs propriétés semi-conductrices. En dopant le Zn1-xMgxO par un ou plusieurs atomes métalliques trivalents, on peut également créer des électrodes transparentes (TCO) pouvant substituer les électrodes traditionnelles à base d'indium (ITO). Les couches minces synthétisées au cours de ce travail ont été réalisées par spray-CVD, une technique de dépôt hybride et innovante utilisant un mode de chauffage radiatif. Les améliorations apportées au réacteur expérimental et les avantages qu'elles dégagent en font une alternative crédible aux techniques traditionnelles. Les couches de Zn1-xMgxO ainsi synthétisées exhibent de très bonnes propriétés, dont une énergie de gap facilement ajustable, une forte mobilité électronique et une très bonne transparence. De même, des couches de ZnS ont été réalisées par l'usage d'un précurseur original, permettant de s'affranchir du ZnCl2 (corrosif) couramment utilisé en spray pyrolyse. Les différents TCO étudiés ont montré de faibles résistivités (10-3 Ω.cm) et ont pu être testés dans des cellules solaires organiques en structures inverses. / In the field of photovoltaic devices, organic and CIGS-based solar cells are both promising way to compete with silicon-based technologies for low and high power generation. In order to provide safe and cost-effective thin films for these devices, zinc chalcogenides layers represent interesting opportunities to replace indium (expensive) and cadmium-based (toxic) layers. Semiconductors like Zn1-xMgxO and ZnS had been synthesized using an infrared assisted spray-CVD apparatus. The interaction between an aerosol and the infrared radiation is the main innovation in this process and sparked off many advantages. With this simple, vacuum-free and chemical soft technique, Zn1-xMgxO thin films exhibit excellent optical transparency, high electrical conductivity and an easily band gap adjustment. The obtained properties, compared with those reported by other traditional techniques, classed infrared assisted spray-CVD as an interesting and promising alternative technique in order to deposit thin films for such applications. ZnS thin films had been prepared with an original chemical precursor which enable to work without ZnCl2, the traditional corrosive chemical precursor in spray pyrolysis. In addition to that, some transparent conductive oxides (TCO) had been investigated by doping ZnO and Zn1-xMgxO layers with aluminum and/or gallium. With a very high optical transparency and a resistivity as low as 10-3 Ω.cm, ZnO:Al exhibit workable properties as transparent electrodes. Indeed, inverted organic solar cells had been realized with those TCO and proved their well-functioning into such devices.

No description available.

<p>Metamorphic buffer (MB) layers were studied as a means to grow epilayers on top of a GaAs substrate which have different lattice constant than the GaAs. Growths were done by molecular beam epitaxy on a GaAs (001) substrate. The growths of step-graded InGaAs and InGaAsP MBs have been investigated using both linear and logarithmic grading profiles. The logarithmic grading profile shows slight improvement in the crystal quality over the linear grading profiles. This is an indication that instead of increasing the strain with the same grading rate, it may be helpful to have higher grading rate at the beginning and lower grading rate at the end of the buffer. InGaAsP graded buffers were grown where group III ratio was kept fixed. However due to the existence of phase separation and lower relaxation the quaternary growths exhibited no performance improvement as might have been expected from growths with only group V grading. Also, the effects of using an InGaP layer grown at low temperature before the MB were determined. Quantum wells (QW), which were grown on top of the MBs, were used to probe the optical emission properties. No significant difference was observed in photoluminescence between the samples with a low temperature layer and without a low temperature layer. Annealing enhanced the PL intensity but the crystal quality degraded due to the appearance of surface defects. Surface undulations, known as “cross-hatch” (CH), were observed in the top MB layers. Atomic force microscopy (AFM) was used to analyze the surface morphology and degree of polarization (DOP) measurement was used to analyze the strain features in the final MB layer. Similar patterns of both surface morphology and strain field indicate a correlation between these two. From analysis of the periodicity of strain field and the CH, evidence was found in the support of one of the existing models of CH evolution which implies that the CH appears before the formation of MDs and subsequently MDs form at some troughs in the undulation.</p> / Master of Applied Science (MASc)

Die vorliegende Arbeit beschäftigt sich mit der Entwicklung neuer Schichtsysteme für die Realisierung biaxial texturierter hochtemperatursupraleitender Bandleiter. Bisher sind eine Vielzahl von Bandleiterarchitekturen bekannt, die sowohl durch physikalische Depositionsmethoden als auch mittels Abscheidung aus der chemischen Lösung hergestellt werden können. Während die Funktion von YBCO-Bandleitern mit Hilfe physikalischer Depositionsmethoden in den letzten Jahren demonstriert werden konnte, zeigen auf chemischem Wege deponierte Bandleiter schlechtere Eigenschaften. Seitens der Industrie besteht ein starkes Interesse, die hohen Produktionskosten, die im Hinblick auf physikalische Depositionsmethoden mit einem hohen Anlagenaufwand verbunden sind, anhand der kostengünstigen chemischen Synthese von Einzelschichten oder der gesamten Bandleiterarchitektur zu senken. Gelöst wurde diese Aufgabe innerhalb der vorliegenden Arbeit durch die Entwicklung metallorganischer Vorstufenlösungen zur Deposition von CaTiO3-, SrTiO3-Pufferschichten und supraleitender YBa2Cu3O7-Schichten.

Inexhaustible solar energy, which provides a clean, economic and green energy, seems to be an alternative solution, for current and future energy demands. Harvesting solar energy presents a challenge in using eco-friendly, earth abundant and inexpensive materials. Although present CdTe and Cu (In, Ga)Se2 (CIGS) technologies, provide light-to-electricity comparable to silicon technology, toxicity of Cd and scarcity of In limits the widespread utilization. Future tera-watt level module capacity would then be feasible by the low-cost technologies. The chalcogenide thin film technology would therefore provide the exceptional utilization in the large-area module monolithic integrations benefitting from the low material consumption owing to the direct band gap. The current thesis presents the results obtained from the quest of other thin film materials and their utilization to an unconventional Cd-free buffer layer. The films suitability for the future applications was assessed through photovoltaics device studies in a comparative manner. Chapter-1 deals with the motivation for the solar energy and the importance of thin film photovoltaics. Alternative materials which are abundantly available would help to reach the future tera watt level production, where the conventional silicon technology alone cannot satisfy the global energy demand. The utilization of non-conventional thin film based solar cells and their working principles were elucidated. The histories of the copper based alternative materials were introduced. Chapter-2 deals with the versatile thin film growth technique that has been designed fabricated and installed further which can handle the growth of the absorber and the top TCO layers with insitu sulphurisation. The methodology of the absorber deposition was discussed in detail. The experimental details for the co-sputtering of CuInAl alloy were presented. A novel selenization method, assisted by the combination of inert gases was developed for the annealing of CuInAl alloyed precursor films. Chapter-3 deals with the presentation of the results obtained on buffer and window layers. Chemical Bath deposition technique was employed for the growth and optimization of the conventional CdS and non-toxic buffer ZnS buffer layers. A) Cadmium sulphide thin films suitable for the utilization of high efficiency solar cells were optimized. Optimization of the buffer involved the effects of cadmium precursors, ammonia concentration and buffer capsule effect. A green route was presented so as to consume the precursors to the maximum extent possible. B) The alternative non-toxic buffer Zinc Sulphide (ZnS) thin films were successfully grown using the above optimized conditions. Moreover the window layer was also optimized for better device partner. Zinc Oxide was used as a n-type partner for the p-type CIS films. The ZnO films were grown by the RF-sputtering from the single cathode exhibited good crystallinity with Zincite structure (hexagonal ZnS, a= 3.249A0 and c= 5.205A0). All the grown films showed high resistivity. Al: ZnO thin films were optimized in two methods 1) by dc co-sputtering from the elemental cathodes, Zinc and Aluminum, 2) dc-sputtering from the single 2% Al-doped ZnO cathode. Low resistivity Al:ZnO thin films were deposited in both the cases. Effect of Aluminum doping into ZnO crystal lattice upon the optical and electrical properties were discussed. Chapter-4 deals with the synthesis of various absorber materials, characterizations and some properties. Briefly the A) Optimization of the CuIn1-xAlxSe2 phase with better adhesion and better crystallinity. Aluminum doping into the crystal lattice of CuInSe2 aided the wide band gap tuning of CIAS thin films. Morphological investigations were carried out for the different set of thin films before and after selenization. Effects of copper and Aluminum concentrations on the lattice parameter of the selenized thin films were addressed. The present chapter deals with the A) electrical properties of CIAS films and its heterojunction partners. Resistivity measurements and effects of Cu/In ratio and the effect of Al doping were described in detail. The CIAS/ZnO heterostructure, CIAS/Al:ZnO heterostructure junction properties as a function of different sun illuminations were discussed. B) The alternative earth abundant, eco-friendly, non-toxic elements Cu2ZnSnS4, absorber thin films synthesis and characterizations. Photo conductive photo measurements showed CZTS a potential candidate for near infra-red photodectection. C) Cu2CoSnS4 (CCTS) nanostructures and quantum dots were synthesized via simple chemical routes. CCTS quantum dots were tuned to exhibit the red edge effect and cold white phosphors. D) Cu3BiS3 nano rods were synthesized and characterized structurally and optically. The transport properties of Cu3BiS3 nanorods were tailored for showing the metallic to semiconducting transitions. Chapter-5 Discusses the A) Efforts made in understanding the CIAS based solar cells through interfaces such as CIAS/ZnO, Mo/CIAS, CIAS/CdS/i-ZnO/Al:ZnO and improving the open circuit voltage VOC upon a rotating substrate, involving the inline and in situ processes, for fabricating the cell/ module were discussed. The device statistics for various set of cells were analyzed. B) Solar cells of CTS absorber with the non-toxic buffer ZnS were fabricated and device properties were analyzed. C) CCTS quantum dots embedded in the polymer matrix were utilized for making the inverted hybrid solar devices in combination of ITO/AZnO bilayered contact replacing the acidic PEDOT: PSS. D) The solar cells made of CCTS hollow spheres by spin coating the absorber in the configuration SLG/Mo/CCTS/CdS/ iZno-AZnO/Ni-Al-Al showed a lower efficiency of 0.02%. Chapter-6 concludes with the summary of present investigations and the scope for future work.

Die vorliegende Arbeit beschäftigt sich mit der Entwicklung neuer Schichtsysteme für die Realisierung biaxial texturierter hochtemperatursupraleitender Bandleiter. Bisher sind eine Vielzahl von Bandleiterarchitekturen bekannt, die sowohl durch physikalische Depositionsmethoden als auch mittels Abscheidung aus der chemischen Lösung hergestellt werden können. Während die Funktion von YBCO-Bandleitern mit Hilfe physikalischer Depositionsmethoden in den letzten Jahren demonstriert werden konnte, zeigen auf chemischem Wege deponierte Bandleiter schlechtere Eigenschaften. Seitens der Industrie besteht ein starkes Interesse, die hohen Produktionskosten, die im Hinblick auf physikalische Depositionsmethoden mit einem hohen Anlagenaufwand verbunden sind, anhand der kostengünstigen chemischen Synthese von Einzelschichten oder der gesamten Bandleiterarchitektur zu senken. Gelöst wurde diese Aufgabe innerhalb der vorliegenden Arbeit durch die Entwicklung metallorganischer Vorstufenlösungen zur Deposition von CaTiO3-, SrTiO3-Pufferschichten und supraleitender YBa2Cu3O7-Schichten.