<div>This dissertation presents a strategy that incorporates nature and bio-inspired shapes to redesign turbine airfoils and stator-rotor rim seal cavity.</div><div><br></div><div>The first objective consists of the development of tools to optimize the turbine velocity triangles and then the 3D shape using 75 parameters. Design trends that minimize loss in the stator and rotor were discussed. The second objective expands on the first by incorporating wavy structures at the leading and trailing edges as well as the suction side mimicking design features of seal whiskers and tubercles of a whale. The airfoils were optimized to maximize the efficiency of a highly loaded high-pressure turbine at positive incidence.</div><div><br></div><div>The last objective addressed the design of the cavity to reduce cooling massflow and protect the turbine platform. A novel strategy was proposed to assess and optimize the shape of the cavity. In an attempt to simply the problem and identify the main physical phenomena, a slice of the flow was examined by considering a purely a 2D case in the relative frame of reference. This simplification enabled the cavity to be optimized in 2D using a geometry inspired by the meandering of rivers. The optimization produced designs that reduce the heat flux in the rear rotor platform and are less sensitive towards variations in gap and cavity total pressure. The methodology was demonstrated in 3D rotating cavity and later in a full turbine stage configuration. The strategy and design tools developed in this dissertation seek to provide understanding of the effects of bio-inspired shapes on turbine blades and lay the foundation for future experimental research into cavity flows.<br></div>

Ces travaux de thèse portent sur la conception et sur la caractérisation expérimentale de résonateurs opto-phononiques. Ces structures permettent le confinement simultané de modes optiques et de vibrations mécaniques de très haute fréquence (plusieurs dizaines jusqu’à plusieurs centaines de GHz). Cette étude a été effectuée sur des systèmes multicouches à l’échelle nanométrique, fabriqués à partir de matériaux semiconducteurs de type III-V. Ces derniers ont été caractérisés par des mesures de spectroscopie Raman de haute résolution. Grâce aux méthodes expérimentales et aux outils numériques développés, nous avons pu explorer de nouvelles stratégies de confinement pour des phonons acoustiques au sein de super-réseaux nanophononiques, à des fréquences de résonance de l’ordre de 350 GHz. En particulier, nous avons étudié les propriétés acoustiques de deux types de résonateurs planaires. Le premier est basé sur la modification adiabatique du diagramme de bande d’un cristal phononique unidimensionnel. Dans le deuxième système, nous utilisons les invariants topologiques caractérisant ces structures périodiques, afin de créer un état d’interface entre deux miroirs de Bragg phononiques. Nous nous sommes ensuite intéressés à l’étude de cavités opto-phononiques permettant le confinement tridimensionnel de la lumière et de vibrations mécaniques de haute fréquence. Nous avons mesuré par spectroscopie Raman les propriétés acoustiques de résonateurs phononiques planaires placés à l’intérieur de cavités optiques tridimensionnelles, de type micropiliers. Enfin, la dernière partie de cette thèse porte sur l’étude théorique des propriétés optomécaniques de micropiliers GaAs/AlAs. Nous avons effectué des simulations numériques par éléments finis, nous permettant d’expliquer les mécanismes de confinement tridimensionnel de modes acoustiques et optiques dans ces systèmes, et de calculer les principaux paramètres optomécaniques. Les résultats de cette étude démontrent que les micropilier GaAs/AlAs possèdent des caractéristiques prometteuses pour de futures expériences en optomécanique, telles que des fréquences de résonance acoustiques très élevées, de hauts facteurs de qualités mécaniques et optiques à température ambiante, ou encore de fortes valeurs pour les facteurs de couplage optomécaniques et pour le produit Q • f / The work carried out in this thesis addresses the conception and the experimental characterization of opto-phononic resonators. These structures enable the confinement of optical modes and mechanical vibrations at very high frequencies (from few tens up to few hundreds of GHz). This study has been carried out on multilayered nanometric systems, fabricated from III-V semiconductor materials. These nanophononic platforms have been characterized through high resolution Raman scattering measurements. The experimental methods and the numerical tools that we have developed in this thesis have allowed us to explore novel confinement strategies for acoustic phonons in acoustic superlattices, with resonance frequencies around 350 GHz. In particular, we have studied the acoustic properties of two nanophononic resonators. The first acoustic cavity proposed in this manuscript enables the confinement of mechanical vibrations by adiabatically changing the acoustic band-diagram of a one-dimensional phononic crystal. In the second system, we take advantage of the topological invariants characterizing one dimensional periodic structures, in order to create an interface state between two phononic distributed Bragg reflectors. We have then focused on the study of opto-phononic cavities allowing the simultaneous confinement of light and of high frequency mechanical vibrations. We have measured, by Raman scattering spectroscopy, the acoustic properties of planar nanophononic structures embedded in three-dimensional micropillar optical resonators. Finally, in the last sections of this manuscript, we investigate the optomechanical properties of GaAs/AlAs micropillar cavities. We have performed numerical simulations through the finite element method that allowed us to explain the three-dimensional confinement mechanisms of optical and mechanical modes in these systems, and to calculate the main optomechanical parameters. This work shows that GaAs/AlAs micropillars present very interesting properties for future optomechanical experiments, such as very high mechanical resonance frequencies, large optical and mechanical quality factors at room temperature, and high values for the vacuum optomechanical coupling factors and for the Q • f products

A great deal of attention has been paid to brown carbon aerosol in the troposphere because it can both scatter and absorb solar radiation, thus affecting the Earth’s climate. However, knowledge of the optical and chemical properties of brown carbon aerosol is still limited. In this thesis, we have investigated different aspects of the optical and physicochemical properties of various brown carbon aerosol samples of potential atmospheric importance. First, reactions involving the di-carbonyl species methylglyoxal (MG) have been previously suggested as an important pathway for the production of secondary organic aerosol (SOA) in the atmosphere. Reaction in an aqueous inorganic salt solution, such as ammonium sulfate (AS), leads to the formation of light-absorbing brown carbon (BrC) product. In this thesis work, we employed a variety of experimental approaches to investigate the optical and physicochemical properties of BrC aerosol generated from this AS-MG reaction (BrC (AS/MG)). Optical properties of the dried BrC (AS/MG) aerosol particles were studied by Fourier transform infrared (FTIR) extinction spectroscopy in the mid-infrared region, cavity ring-down spectroscopy (CRDS) at 403 nm in the visible, and by measuring the light scattering phase function and polarization profiles at two different visible wavelengths, 532 and 402 nm. In addition, we used UV−vis spectroscopy to measure the mass absorption coefficient (MAC) of the solution-phase reaction products. The different optical properties were measured as a function of reaction time for a period of up to 22 days. The UV-vis absorption spectra showed a clear increase in measured MAC in the visible and near UV as the solution aged. However, analysis of the light scattering data showed no significant differences between AS and BrC aerosol in the derived refractive indices at either 532 or 402 nm, even for the longest reaction times. The FTIR extinction spectra was modeled in a Mie theory simulation to derive the complex refractive index in the mid-IR range (7000-800 cm−1); the results showed no significant changes in either the real or the imaginary parts of the refractive indices for BrC (AS/MG) aerosol particles when compared to unreacted AS aerosol. From the CRDS extinction data, the optical constants for BrC (AS/MG) particles at 403 nm were also determined through a Mie theory based analysis. The retrieved real index of refraction at 403 nm is n = 1.551 ± 0.005, with an imaginary index value of k = 0.000 ± 0.002; these values do not appear to change significantly with aging time over the course of 22 days and are not markedly different from the AS aerosol values. The small imaginary index value suggests that BrC (AS/MG) aerosol formed from this pathway may not significantly contribute to warming. In addition, CRDS measurements of the BrC (AS/MG) aerosol extinction at 403 nm as a function of particle size show a significant deviation from Mie theory simulations for particles with diameters of ≳500 nm, probably as a result of non-spherical particle shape effects. We also employed atomic force microscopy (AFM)-based IR spectroscopy to investigate the morphology and chemical composition of single SOA particles. AFM analysis of the particle morphology shows that a significant fraction of BrC (AS/MG) particles with diameters of ≳500 nm are non-spherical in shape, consistent with our observed breakdown in the applicability of Mie theory for larger particles. In addition to these measurements, we have characterized additional physicochemical properties of the BrC (AS/MG) aerosol particles including hygroscopic growth using a tandem-differential mobility analyzer. Compared to AS, BrC aerosol particles are found to have lower deliquescence relative humidity (DRH), efflorescence relative humidity (ERH), and hygroscopic growth at the same relative humidity values. Second, we investigated the optical properties of the water soluble products of limonene BrC generated from ozonolysis of d-limonene with further aging by AS. Optical constants for the dried limonene BrC aerosol product were measured at 403 nm by CRDS over the course of 9 days of aging. While the fresh limonene BrC aerosol showed a significant non-zero absorption index, the aged samples showed absorption index values consistent with zero. This result was somewhat unexpected because UV-vis absorption spectra of the bulk reaction solution showed a continued increase in absorption as the solution aged. One possible explanation for this result is that there could be an increase in the fraction of volatile chromophores as the solution ages, that are then removed in the aerosol drying process. Third, we investigated optical properties and chemical compositions of several humic substance (HS) reference samples including humic acid (HA) and fulvic acid (FA) standards by CRDS, UV-vis spectroscopy, elemental analysis, and 13C NMR spectroscopy. Measurements of the optical properties of HS is important in atmospheric science, because it is thought that HS samples have similar optical properties to organic materials, such as HUmic-Like Substances (HULIS), that exist in clouds, fogs, rainwater, and atmospheric aerosol. The humic acid aerosol samples generally showed higher absorption index values than the fulvic acid aerosol samples. We also found a correlation between the absorption index and chemical composition, with the value for k generally increasing with both increasing carbon-to-oxygen atomic ratio and sample aromaticity. In addition, we compared our measured optical constants for the HS aerosol samples with results from previous studies of field collected HULIS. The absorption index values for the fulvic acid aerosol samples give a better match than the humic acid samples when compared to the results from the field collected samples. Overall, these studies provide new details of the optical and physicochemical properties of a class of brown carbon organic aerosol which may have important implications for atmospheric chemistry and climate.

Sweden has a climate target to get a total renewable electricity production by 2040, in order to succeed with the goal, the proportion of solar energy needs to increase. Increased environmental awareness and increased profitability of solar cells have led to an increase. A new way of attaching solar cells to buildings is by integrating them into building materials. A solution that optimizes material, makes the installation easier and creates better design. Today, there is concern that the temperature of the solar cells may become very high as their cooling decreases. The consequences of an increased temperature in the solar cells is that the efficiency of the electricity production decreases. The purpose of this study is therefore to increase understanding of the influence of modular temperature on electricity production. The aim of the study was to find out how much electricity production [kWh/m2, year] varies in solar cells depending on whether they are applied to buildings or if they are integrated into building materials for solar cells placed in Nordic climate. In order to do this, a calculation model was built in Simulink Matlab to calculate how the modular temperature varied during the varying weather conditions that occur during a year in Gothenburg. Air flow in the gap is created by self-convection. Some periods blew the wind into the gap in the ceiling and then the wind was also assumed to contribute with an air flow. In order to describe the self-conception, a theoretical relationship was established, to describe how the wind influenced the airflow of the roof, a connection from an experimental study was used. With the help of the calculated calculation model, it was possible to determine how much electricity production varied during integrated or applied assembly in Gothenburg. The result found was an increase of 4% for ceiling-mounted and 2% respectively for wall-mounted solar cells with applied mounting compared to integrated installation. The model was also tested for a warmer and a colder climate, Rome and Luleå. The conclusion was that building-applied solar cells can increase electricity production by up to 4% for solar cells on roofs and up to 2% for solar cells placed on the wall in Nordic climate compared to fully integrated solar cells, an air gap is therefore more effective for solar cells placed on roofs than on the wall. It was found that in warmer climates, as in Rome, the corresponding increase in electricity production was about double that for both roof and wall, an air gap is therefore more efficient in a warmer climate.

Adaptive optics work to reduce optical losses in the LIGO detectors, making them more sensitive to gravitational wave events. Mode-mismatch between the coupled optical cavities, caused by uncertainty in the radii of curvature and orientation of the interferometer optics, is one of the main sources of loss in Advanced LIGO. Thermal actuators are used to dynamically change the radius of curvature of certain interferometer optics, allowing mode mismatches to be reduced. Finely tunable astigmatic mirrors have the potential to be very useful in gravitational wave detectors for beam reflections at non-normal incidence, but have never been tested. These astigmatic composite mirrors are constructed by bonding a fused silica mirror to a non-axially-symmetric metal plate. When heated, the mirror is differentially distorted in the x- and y-directions due to its asymmetric design, resulting in an elliptical reflected beam profile. We model and test an initial mirror design, finding that it does, in fact, act as an astigmatic mirror. This finding opens a new avenue towards development of adaptive optics for current and next-generation gravitational wave detectors.

Cavity ringdown spectroscopy (CRDS) makes use of light retention in an optical cavity to enhance the sensitivity to absorption or extinction of light from a sample inside the cavity. When light entering the cavity is stopped, the output is an exponential decay with a decay constant that can be used to determine the quantity of the analyte if the extinction or absorption coefficient is known. The precision of the CRDS is dependent on the rate at which the system it acquires and processes ringdowns, assuming randomly distributed errors. We have demonstrated a CRDS system with a ringdown acquisition rate of 1.5 kHz, extendable to a maximum of 3.5 kHz, using new techniques that significantly changed the way in which the ringdowns are both initiated and processed. On the initiation side, we combined a custom high-resolution laser controller with a linear optical feedback configuration and a novel optical technique for initiating a ringdown. Our optical injection "unlock" method switches the laser off-resonance, while allowing the laser to immediately return to resonance, after terminating the unlock, to allow for another ringdown (on the same cavity resonance mode). This part of the system had a demonstrated ringdown initiation rate of 3.5 kHz. To take advantage of this rate, we developed an optimized cost-effective FGPA-based data acquisition and processing system for CRDS, capable of determining decay constants at a maximum rate of 4.4 kHz, by modifying a commercial ADC-FPGA evaluation board and programming it to apply a discrete Fourier transform-based algorithm for determining decay constants. The entire system shows promise with a demonstrated ability to determine gas concentrations for H2O with a measured concentration accuracy of ±3.3%. The system achieved an absorption coefficient precision of 0.1% (95% confidence interval). It also exhibited a linear response for varying H2O concentrations, a 2.2% variation (1σ) for repeated measurements at the same H2O concentration, and a corresponding precision of 0.6% (standard error of the mean). The absorption coefficient limit of detection was determined to be 1.6 x 10-8 cm-1 (root mean square of the baseline residual). Proposed modifications to our prototype system offer the promise of more substantial gains in both precision and limit of detection. The system components developed here for faster ringdown acquisition and processing have broader applications for CRDS in atmospheric science and other fields that need fast response systems operating at high-precision.

Scientists have been observing a change in the climate since the beginning of the 20th century that cannot be attributed to any of the natural influences of the past. Natural and anthropogenic substances and processes perturb the Earth's energy budget, contributing to climate change. In particular, aerosols (particles suspended in air) have long been recognized to be important in processes throughout the atmosphere that affect climate. They directly influence the radiative balance of the Earth's atmosphere, affect cloud formation and properties, and are also key air pollutants that contribute to a variety of respiratory and cardiovascular diseases. Despite their importance, aerosol particles are less well-characterized than greenhouse gases with respect to their sources, temporal and spatial concentration distribution, and physical and chemical properties. This uncertainty is mainly caused by the variable and insufficiently understood sources, formation and transformation processes, and complex composition of atmospheric particles. Instruments that can precisely and accurately measure and characterize the aerosol physical and chemical properties are in great demand. Atmospheric relative humidity (RH) has a crucial impact on the particles' optical properties; the RH dependence of the particle extinction coefficient is an important parameter for radiative forcing and thus climate change modeling. In this work a Humidity-Controlled Cavity Ring-Down (HC-CRD) aerosol optical instrument is described and its ability to measure RH dependent extinction coefficients and related hygroscopicity parameters is characterized. The HC-CRD is capable of simultaneously measuring the aerosol extinction coefficient at three wavelengths (λ = 355, 532, and 1064 nm) and three different RHs (typically 20%, 50%, and 80%). A range of chemicals and their mixtures were used to produce laboratory generated aerosols. Three mixture systems include one inorganic salts mixture system consisting of (NH4)2SO4, NH4HSO4, Na2SO4, NaHSO4 serve as surrogates of the ionic salts found in the atmosphere. Two organic mixture systems were investigated: mixtures of NaCl, D-glucose, sucrose, and glycine are benchmarks for compounds emitted from biomass burning. Finally, mixtures of (NH4)2SO4 (ammonium sulfate, AS) with a series of dicarboxylic acids including malonic acid, adipic acid, and azelaic acid are used as benchmarks to mimic urban pollutants. The extinction coefficients were obtained as a function of RH from the HC-CRD measurements, from which optical growth factors f(RH) and γ(RH) values can be determined to examine their dependence on chemical composition. A volume mixing rule was used to calculate the effective refractive index of the binary substrate mixtures, since both size and composition change during water uptake. The SDA/FMC algorithm developed by O'Neill, et al. 2005 is used to extract the van de Hulst phase shift parameter (Ρeff) from three-wavelength measurements of extinction. The fine mode fraction of extinction (η) and fine mode effective radius (Reff) of laboratory generated aerosol particles can be then determined. An iterative algorithm was developed to retrieve the change in refractive index of particles as function of RH. The calculated Reff of aerosols at different RHs were used to obtain the physical size growth factor (gf), and κ(RH). The size changes as a function of water uptake describe the dependence of aerosol optical properties on chemical composition. This work demonstrates the capability of conducting aerosol optical measurements using HC-CRD to determine the RH dependence of aerosol optical properties. The HC-CRD measurements combined with the SDA/FMC method to retrieve aerosol size for laboratory generated aerosols establish the connection between the optical properties and the aerosol particles' chemical compositions. It also underlines the importance and need for future investigation on the hygroscopic properties of atmospheric aerosols. This work is successfully developed a method that enables using the aerosols optical measurements to predict the compositions; it will greatly contribute to the atmospheric aerosol measurement and global climate modelling.

Dans cette thèse, une étude des microstructures périodiques et de leurs applications à la modulation optique par ondes acoustiques est présentée. Plus spécifiquement, le sujet traite du couplage opto-mécanique dans les cavités des cristaux phoXoniques. Cette étude montre comment la théorie des perturbations fournit un outil efficace d’analyse et de prédiction du comportement de la modulation dans de telles structures. Cette méthode permet également d’économiser du temps de calcul en comparaison aux calculs numériques purs. L'étude théorique de la propagation des ondes dans les milieux périodiques est d'abord introduite, puis les paramètres de l'existence simultanée des bandes interdites photoniques et phononiques sont déduites. Le développement d’une méthode semi-analytique ayant pour but d’analyser l'efficacité du couplage acousto-optique dans les structures périodiques artificielles est ensuite réalisé. La théorie des perturbations est développée jusqu'au 2ème ordre. Celle-ci, associée à des considérations de symétrie, est utilisée pour l'interprétation des résultats. Une illustration de la versatilité de la méthode, basée d'une cavité ponctuelle L1 sur substrat silicium, est présentée. Les résultats obtenus sont en accord avec ceux donnés par une méthode purement numérique. / In this thesis, a study of periodic microstructures and their applications to optical modulation by acoustical waves is presented. More specifically, it deals with opto-mechanical coupling in phoXonic crystal cavities. This study shows how the perturbation theory provides an efficient tool to analyse and predict the behaviour of modulation in such structures. Moreover, when compared to pure numerical ones, this method leads to calculation time saving. The theory of periodic media is first introduced and then we derive the parameters for the simultaneous existence of photonic and phononic bandgaps. We end up by the development of a semi-analytical method to analyze acousto-optical coupling efficiency in artificial periodic structures. The perturbation theory is developed up to 2nd order and is used together with symmetry considerations for interpretations. An illustration of the versatility of the developed method is presented using an L1 point defect cavity on silicon substrate and validated with classical numerical results.

Spacecraft in orbit experience temperature swings close to 240 K as the craft passes from the shadow of the Earth into direct sunlight. To regulate the craft’s internal energy, large radiators eject unwanted energy into space using radiation transfer. The amount of radiation emitted is directly related to the topology of the radiator design. Deformable structures such as those made with origami tessellation patterns offer a mechanism to control the quantity of energy being emitted by varying the radiator shape. Three such patterns, the Waterbomb, Huffman Waterbomb, and Huffman Stars-Triangles, can be folded into tubes. Origami tubes offer greater control and simplicity of design than flat radiators. Using FLUENT, Origami Simulator, and Solidworks to first simulate and then analyze the flow of a thermal fluid through the patterns and the radiation emitted from the created bodies, it was determined that the Waterbomb pattern achieved a 17.6 percent difference in emitted radiation, over a 2 percent change in fold. The Huffman Waterbomb pattern displayed a 42.7 percent difference in emitted radiation over a 20 percent change of fold. The simulations demonstrated both the feasibility and benefits of the origami designed tubes.

Cette thèse, à la fois numérique et expérimentale, porte sur l’étude du transfert de chaleur par convection naturelle qui apparait au sein d’une cavité hémisphérique en régime stationnaire. L’enceinte est remplie d’eau ou de nanofluide de type eau / ZnO. La fraction volumique varie entre 0 (eau pure) et 10%. La coupole de la cavité est maintenue à température froide. Ce travail s’applique au domaine de l’ingénierie électronique et plus particulièrement au refroidissement des composants actifs de différentes formes. Trois géométries de sources de chaleur sont étudiées : la première est plane et circulaire (disque) et les suivantes, centrées sur le disque, de même surface d’échange, sont cubique et hémisphérique. L’angle d’inclinaison du disque varie entre 0 (coupole orientée vers le haut) et 180° (coupole orientée vers le bas) par rapport au plan horizontal. Les sources de chaleur génèrent des puissances qui conduisent à des Rayleigh importants. L’approche numérique est effectuée à l’aide de la méthode des volumes finis basée sur l’algorithme SIMPLE et un modèle monophasique. Pour chaque source active, le transfert de chaleur convectif est analysé et quantifié par l’intermédiaire d’une corrélation du type Nusselt-Rayleigh-Prandtl-angle d’inclinaison. D’un point de vue expérimental, la fabrication des sources de chaleur est minutieusement décrite étape par étape et le calcul du coefficient de transfert convectif moyen expérimental est détaillé. La comparaison mesures-corrélations remet en question l’efficacité du nanofluide en termes de refroidissement. / This numerical and experimental thesis deals with natural convective heat transfer that occurs in a hemispherical cavity in steady state. The enclosure is filled with water or ZnO / water nanofluid. The volume fraction varies between 0% (pure water) and 10%. The coupola of the cavity is kept at a cold temperature. This work corresponds to the field of electronics and the cooling of different actives composants. Three active heating sources are studied: the first one is plane and circular (the disc) and the followings, centered on the disc with the same surface, are cubical and hemispherical. The tilted angle varies between 0 (dome facing upwards) and 180° (dome facing downwards) with respect to the horizontal plane. Heat sources generate important heat fluxes leading to high Rayleigh numbers values. Numerical approach is done by means of the volume control method based on the SIMPLE algorithm and using monophasic model. For each active source, the convective heat transfer is analyzed and quantified by means of a correlation of the Nusselt-Rayleig-Prandtl-tilt angle type. Experimentally, the heat sources are built step by step and the average convective heat transfer coefficient is calculated. The comparison measures-correlations questions on the cooling nanofluid’s efficiency.