The main objective of this thesis is to review the problems of stone facades according to the performance criteria determined with codes and standards and to propose solutions for proper application. In this process the codes, standards, other documents and the knowledge of the researcher all served to determine the inadequacies present in this field. The thesis also aims at clarifying the terminolgy confusion related to stone cladding and stone curtain wall.

Devido à demanda de aumento de produtividade na indústria, a utilização de materiais mais leves, busca por processos de reparos com melhor custo, em conjunto com o avanço das tecnologias, evolução dos processos de soldagem, e esses fatores aliados aos benefícios de uma maior taxa de fusão, melhor controle da penetração, faz com que o processo MIG/MAG com polaridade variável apresente consideráveis avanços tecnológicos nos dias de hoje. Porém, a seleção dos parâmetros da curva típica de corrente do processo (composta por corrente de pico, corrente de base positiva e corrente negativa), é ainda um desafio. Buscando um melhor entendimento da influência da polaridade negativa no processo de soldagem, em especial para aplicações de revestimento, este trabalho tem como objetivo analisar os parâmetros da polaridade negativa individualmente em relação a geometria do cordão de solda, utilizando aço ao carbono como metal base e aço inoxidável como metal de adição. O planejamento e execução do experimento foi realizado com base na metodologia de projeto de experimentos Box-Behnken, variando três fatores: tempo de corrente negativa, intensidade de corrente negativa e tempo de corrente de base positiva, em três níveis cada um. Primeiramente alcançou-se a minimização da diluição, onde o tempo de corrente negativa apresentou efeito significativo no resultado final, sendo seu nível máximo (15 ms) o responsável pelos menores valores de diluição, aproximadamente 12%, recomendado em soldagem para revestimento. Posteriormente, foi avaliado o efeito dos parâmetros em relação à penetração, altura e largura do cordão de solda, sendo o tempo de corrente negativa em 15 ms e corrente negativa em -150 A os níveis que apresentaram melhores resultados. Após, os parâmetros da polaridade negativa utilizados foram comparados com os termos proporcionais sugeridos pela literatura (%EN). E, por fim, avaliou-se uma forma de curva de corrente sem a corrente de base positiva, onde foi concluído que não há significância das diferentes formas de curva de corrente sobre os resultados na penetração do cordão de solda, assim como a necessidade da corrente de base na estabilidade do arco elétrico do processo. / Due to the demand to increase productivity in the industry, use lighter materials, search for repair processes with better cost, in combination with advancement of technologies, evolution of welding processes, connected with the benefits of a higher melting rate and better control of the process penetration, it was possible to verify advances in the MIG / MAG Variable Polarity welding technique. However, the selection of the parameters of the typical process current curve (composed by peak current, positive current and negative current), is still a challenge today. The aim of this work is to analyze the negative polarity parameters individually in relation to the weld bead geometry, using carbon steel as base metal and stainless steel as addition metal. The planning and execution of the experiment was performed based on the Box-Behnken design methodology, varying three factors: negative current time, negative current intensity and positive base current time, at three levels each one. Firstly, dilution minimization was achieved, which showed that the negative current time had a strong influence on the final result, and the maximum level (15 ms) was responsible for the lowest dilution values, nearby 12%, ideal for welding cladding. Then, the parameters were evaluated in relation to penetration, height and width of the weld bead, which for welding cladding, the negative current time 15 ms and negative current -150 A presented better results. Next, the negative polarity parameters were compared with the proportional terms suggested by the literature (%EN). Finally, a form of current curve without positive base current was evaluated, where it can be concluded that the current curve form does not have significance on the penetration results, as well as the necessity of the base current in the arc electric stability.

O Brasil, no mercado mundial, ocupa lugar de destaque na extração e comercialização das rochas ornamentais e de revestimento, demonstrado pela produção mensal de chapas que é da ordem de 4 milhões de metros quadrados. Dentre suas as diversas formas de aplicações na construção civil, observa-se um incremento do uso em revestimentos de fachadas de edifícios, principalmente nos grandes centros urbanos. A forma de fixação das placas nas fachadas dos edifícios é feita com o auxílio de inserts metálicos, técnica desenvolvida na Alemanha e nos Estados Unidos. O presente trabalho trata da especificação e normatização das rochas ornamentais e, no caso específico dos revestimentos de fachadas, são apresentados diversos aspectos da seleção das placas de rocha e dos inserts metálicos e também o cálculo estrutural de um sistema de revestimento / Brazil procedures more than 4 million 'M POT.2'/month of dimension stones panels. Façades applications increases in last years. The stone façades cladding is accomplished with the use of metallic anchor, that was developed in German and U.S.A. The present work presents the requirements for selection of the stones and the anchor system, a methodology for the calculation of the stone and the anchor and main aspects of standardization regarding dimension stone

Devido à demanda de aumento de produtividade na indústria, a utilização de materiais mais leves, busca por processos de reparos com melhor custo, em conjunto com o avanço das tecnologias, evolução dos processos de soldagem, e esses fatores aliados aos benefícios de uma maior taxa de fusão, melhor controle da penetração, faz com que o processo MIG/MAG com polaridade variável apresente consideráveis avanços tecnológicos nos dias de hoje. Porém, a seleção dos parâmetros da curva típica de corrente do processo (composta por corrente de pico, corrente de base positiva e corrente negativa), é ainda um desafio. Buscando um melhor entendimento da influência da polaridade negativa no processo de soldagem, em especial para aplicações de revestimento, este trabalho tem como objetivo analisar os parâmetros da polaridade negativa individualmente em relação a geometria do cordão de solda, utilizando aço ao carbono como metal base e aço inoxidável como metal de adição. O planejamento e execução do experimento foi realizado com base na metodologia de projeto de experimentos Box-Behnken, variando três fatores: tempo de corrente negativa, intensidade de corrente negativa e tempo de corrente de base positiva, em três níveis cada um. Primeiramente alcançou-se a minimização da diluição, onde o tempo de corrente negativa apresentou efeito significativo no resultado final, sendo seu nível máximo (15 ms) o responsável pelos menores valores de diluição, aproximadamente 12%, recomendado em soldagem para revestimento. Posteriormente, foi avaliado o efeito dos parâmetros em relação à penetração, altura e largura do cordão de solda, sendo o tempo de corrente negativa em 15 ms e corrente negativa em -150 A os níveis que apresentaram melhores resultados. Após, os parâmetros da polaridade negativa utilizados foram comparados com os termos proporcionais sugeridos pela literatura (%EN). E, por fim, avaliou-se uma forma de curva de corrente sem a corrente de base positiva, onde foi concluído que não há significância das diferentes formas de curva de corrente sobre os resultados na penetração do cordão de solda, assim como a necessidade da corrente de base na estabilidade do arco elétrico do processo. / Due to the demand to increase productivity in the industry, use lighter materials, search for repair processes with better cost, in combination with advancement of technologies, evolution of welding processes, connected with the benefits of a higher melting rate and better control of the process penetration, it was possible to verify advances in the MIG / MAG Variable Polarity welding technique. However, the selection of the parameters of the typical process current curve (composed by peak current, positive current and negative current), is still a challenge today. The aim of this work is to analyze the negative polarity parameters individually in relation to the weld bead geometry, using carbon steel as base metal and stainless steel as addition metal. The planning and execution of the experiment was performed based on the Box-Behnken design methodology, varying three factors: negative current time, negative current intensity and positive base current time, at three levels each one. Firstly, dilution minimization was achieved, which showed that the negative current time had a strong influence on the final result, and the maximum level (15 ms) was responsible for the lowest dilution values, nearby 12%, ideal for welding cladding. Then, the parameters were evaluated in relation to penetration, height and width of the weld bead, which for welding cladding, the negative current time 15 ms and negative current -150 A presented better results. Next, the negative polarity parameters were compared with the proportional terms suggested by the literature (%EN). Finally, a form of current curve without positive base current was evaluated, where it can be concluded that the current curve form does not have significance on the penetration results, as well as the necessity of the base current in the arc electric stability.

Este trabalho apresenta uma revisão bibliográfica a respeito dos rejuntes para revestimento cerâmico. A nomenclatura internacional é explorada e os tipos de rejunte e seus empregos são enumerados. Para embasar o leitor sobre o reves-timento cerâmico, os principais conceitos a ele relacionados são exibidos de forma sucinta. Uma vez que o rejunte é um componente importante do revestimento ce-râmico, suas funções dentro desse subsistema são abordadas em detalhes. O as-pecto de alívio de tensões é amplamente comentado, uma vez que essa é uma função essencial do rejunte, particularmente no caso de fachadas. Ao final, são abordados os aspectos de preparo e aplicação dos rejuntes, particularmente os produtos cimentícios. O rejuntamento de locais específicos, como encontros com selantes e interfaces com aparelhos sanitários são detalha-dos com vistas à diminuição da ocorrência de manifestações patológicas futuras. No trabalho experimental, painéis em forma de laje revestidos com placas cerâmicas são submetidos à flexão até a ocorrência de desplacamento, objeti-vando detectar qual a influência da largura da junta e do tipo de argamassa ade-siva na ruptura do corpo-de-prova. Os resultados indicam que a largura das juntas de assentamento assumem importância apenas quando a argamassa adesiva apresenta alta resistência de aderência. / This study presents a bibliographical revision regarding the ceramic tile grouts. Here, the international nomenclature is explored and the types of grouts as well as its employments are enumerated. To base the reader on the ceramic tile cladding, its main concepts are shown succinctly. Being the grout an important component of the ceramic tile cladding, its functions in this subsystem are broached in details. The aspect of stress relief is widely mentioned, for this is an essential function of grout, particularly in the case of facades. In the end, the aspects of the preparation and the application of grouts are broached, particularly the cementitious products. The grouting of specific places such as meetings of sealants and interfaces with sanitary devices is detailed viewing the decrease of the occurrence of future problems. In the experimental study, panels in flagstone form tiled with ceramic plates are submitted to flexion until the occurrence of rupture of these panels, aiming to detect the influence of the joint thickness and of the type of the adhesive mortar in the rupture of the sample. The results indicate that the nesting joint thickness only assumes importance when the adhesive mortar presents high resistance of adherence.

Mechanical components operating at elevated temperatures can be identified in the aerospace industry as well as in metal forming. Hot stamping is a metal forming technique utilized for manufacturing high strength lightweight components for the automotive industry. Three types of Ni-based hardfacings doped with solid lubricants were manufactured using laser cladding. An additional hardfacing was also manufactured using the Ni-based alloy only as a reference. Solid lubricants added were Ag+WS2, WS2 and Cu+MoS2. These hardfacings were manufactured and tribologically evaluated for potential application in hot stamping tooling. Direct diode laser was used for the cladding process. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used for characterization of the microstructure after deposition. Tribological testing was done using a reciprocating pin-on-disk tribometer under dry sliding conditions at temperatures in the range between RT and 600°C. Bearing steel ball and a flat pin made of the same material were used as counterbodies. Wear volume loss was measured using a 3D optical interferometer. For identification of the wear mechanisms SEM/EDS techniqueswere used. Formation of a lubricious CrxSy phase was detected after deposition, additionally encapsulation of silver particles by CrxSy was also observed. Reduction of friction coefficient was observed for every self-lubricating hardfacing compared to the reference. Lowest friction coefficient (0.23-0.3) was observed when the testing temperature was set to 400°C using a pin-on-flat configuration. Lowest wear rate was observed at 400°C, with the coating containing Ag and WS2 having a specific wear rate of 3.04 · 10−5mm3/Nm. The lubricity of the self-lubricating hardfacings was attributed to the CrxSy phase observed on the worn surface. At low to moderate temperatures abrasive wear is the main wear mechanism. At the highest testing temperature, oxidative wear was dominant.

The diploma thesis deals with a new building of a single-storey production object, which is made as a precast concrete frame with a lightweight cladding. Part of the new building is also facilities for employees and its administrative staff, which is also based on precast concrete frame divided into two floors. Cladding is made as masonry with ventilated facade. The internal division of buildings is made by plasterboard partitions. The project is located in the industrial zone Košíkov near Velká Bíteš.

Thesis focuses on the principles and properties of the tilted Bragg fiber gratings. Two models of the principal cladding mode behaviour are proposed and ther respective results compared with experimental data. The experimental setup for the preparation of the tilted gratings is described. The thesis shows the evaluation of the gratings parameters for the set of prepared gratings. Application of the tilted gratings in the sensors is discussed

The purpose of the dissertation is to develop selected parts of technologically – building project of residential houses in Rosice. The building will be used for living. The building has nine building sites, in the dissertation eight building sites are solved. Main building site SO 01 – Apartment house first and second is solved in detail. The dissertation includes a technical report about technologically-building project, the time and financial plan, a study of the realization of the main stage of its construction. The coordination of the building and site equipment including the principles of organisation building are solved graphically. The dissertation also includes a suggestion of the major building machine, plan of securing material source, technological regulations and the check and test plan for performing piles. A part of the dissertation is the budget of the building and safety risks on the building site and during performing piles.

Diploma thesis studies the layers created by laser cladding and method of testing abrasion resistance of these layers using the method of dynamic shock impactor. In the theoretical part describes laser technologies and their applications, hardness testing and methods of testing of coatings. Proposed by the mechanical testing of the selected materials were carried out and evaluated in the experimental part. The conclusion summarizes final results of the experiment.