No description available.

Boundary conditions for the cable equation - such as voltage-clamped or sealed cable ends, branchpoints, somatic shunts, and current clamps - result in multi-exponential series representations of the voltage or current. Each term in the series expansion is characterized by a decay rate (eigenvalue) and an initial amplitude (Fourier coefficient). The eigenvalues are determined numerically and the Fourier coefficients are subsequently given by the residues at the eigenvalues of the Laplace transform of the solution. In this paper, we introduce an alternative method for estimating the Fourier coefficients which works for all types of boundary conditions and is practical even when analytic expressions for the Fourier coefficients become intractable. It is shown that terms in the analytic expressions for the Fourier coefficients result from derivatives of the equation for the eigenvalues, and that simple numerical estimates for the amplitude coefficients are easily derived by replacing analytical derivatives by numerical eigenslope. The physical quantity represented by the slope is identified as effective neuron capacitance.

No description available.

A parallel domain decomposition Laplace transform Boundary Element Method, BEM, algorithm for the solution of large-scale transient heat conduction problems will be developed. This is accomplished by building on previous work by the author and including several new additions (most note-worthy is the extension to 3-D) aimed at extending the scope and improving the efficiency of this technique for large-scale problems. A Laplace transform method is utilized to avoid time marching and a Proper Orthogonal Decomposition, POD, interpolation scheme is used to improve the efficiency of the numerical Laplace inversion process. A detailed analysis of the Stehfest Transform (numerical Laplace inversion) is performed to help optimize the procedure for heat transfer problems. A domain decomposition process is described in detail and is used to significantly reduce the size of any single problem for the BEM, which greatly reduces the storage and computational burden of the BEM. The procedure is readily implemented in parallel and renders the BEM applicable to large-scale transient conduction problems on even modest computational platforms. A major benefit of the Laplace space approach described herein, is that it readily allows adaptation and integration of traditional BEM codes, as the resulting governing equations are time independent. This work includes the adaptation of two such traditional BEM codes for steady-state heat conduction, in both two and three dimensions. Verification and validation example problems are presented which show the accuracy and efficiency of the techniques. Additionally, comparisons to commercial Finite Volume Method results are shown to further prove the effectiveness.

京都大学 / 新制・課程博士 / 博士(理学) / 甲第24177号 / 理博第4868号 / 新制||理||1697(附属図書館) / 京都大学大学院理学研究科化学専攻 / (主査)教授 北川 宏, 教授 有賀 哲也, 教授 吉村 一良 / 学位規則第4条第1項該当 / Doctor of Science / Kyoto University / DGAM

Resistive random access memory (RRAM), based on a two-terminal resistive switching device with a switching element sandwiched between two electrodes, has been an attractive candidate to replace flash memory owing to its simple structure, excellent scaling potential, low power consumption, high switching speed, and good retention and endurance properties. However, due to the current limited understanding of the device mechanism, RRAMs research are still facing several issues and challenges including instability of operation parameters, the relatively high reset current, the limited retention and the unsatisfactory endurance. In this study, we investigated the switching mechanisms, conditions and applications of oxygen vacancy (Vo) filament formation in resistive memories. By studying the behavior of conductive Vo nanofilaments in several metal/oxide/metal resistive devices of various thicknesses of oxides, a resulting model supported by the data postulates that there are two distinct modes of creating oxygen vacancies: i) a conventional bulk mode creation, and ii) surface mode of creating oxygen vacancies at the active metal-dielectric interface. A further investigation of conduction mechanism for the Vo CF only based memories is conducted through insertion of a thin layer of titanium into a Pt/ Ta2O5/Pt structure to form a Pt/Ti/ Ta2O5/Pt device. A space charge limited (SCL) conduction model is used to explain the experimental data regarding SET process at low voltage ranges. The evidence for existence of composite copper/oxygen vacancy nanofilaments is presented. The innovative use of hybrid Vo/Cu nanofilament will potentially overcome high forming voltage and gas accumulation issues. A resistive floating electrode device (RFED) is designed to allow the generation of current/voltage pulses that can be controlled by three independent technology parameters. Our recent research has demonstrated that in a Cu/TaOx/Pt resistive device multiple Cu conductive nanofilaments can be formed and ruptured successively. Near the end of the study, quantized and partial quantized conductance is observed at room temperature in metal-insulator-metal structures with graphene submicron-sized nanoplatelets embedded in a 3-hexylthiophene (P3HT) polymer layer. As an organic memory, the device exhibits reliable memory operation with an ON/OFF ratio of more than 10. / Ph. D.

The majority of this dissertation focuses on proton conducting materials that could be used at high operating temperatures. Higher operating temperatures are desirable as they will increase fuel cell efficiency, reduce cost, and simplify the heat management system. The factors governing proton conduction including segmental mobility, protogenic group identity, and charge carrier density were investigated on a variety of polymers containing 1H-1,2,3-triazole moieties. Proton conductivity measurements were made using AC impedance spectroscopy. Random copolymers and terpolymers of triazole-containing acrylates and poly(ethylene glycol)methyl ether acrylate (PEGMEA) have been synthesized. Conductivity increased with increasing degree of PEG incorporation until reaching a maximum at 30% mole PEGMEA. In comparison to benzimidazole-functionalized polyacrylate with 35% mole PEGMEA, the triazole analog showed a higher proton conductivity, and a less pronounced conductivity temperature dependence. Further increases in conductivity was achieved through the addition of trifluoroacetic acid. To study the effect of charge carrier density on proton conduction, polyacrylates containing a different number of triazole groups per repeat unit were synthesized. The result showed that introduction of more than one triazole per repeat unit did not result in an increase in conductivity as there was an accompanying increase in Tg. To improve the thermal and mechanical properties, triazole groups were tethered to a higher Tg backbone polymer, polynorbornene. Introduction of polyhedral oligomeric silsesquioxane (POSS) into triazole-functionalized polynorbornene was also investigated. In a parallel set of investigations, poly(2-(dimethylamino)ethyl methacrylate), PDMAEMA, and copolymers of DMAEMA and methyl methacrylate (PDMAEMA-co-PMMA) were synthesized via atom transfer radical polymerization (ATRP). Fluorescently-labeled PDMAEMAs were synthesized using fluorescent ATRP initiators to ensure the presence of one dye molecule on every polymer chain. PDMAEMAs and PDMAEMA-co-PMMA with different molecular weights have been deposited onto a negatively-charged silica surface via controlled flow deposition. The results show that the polymer deposition rate depends on molecular weight, and is inversely proportional to molecular weight. A preliminary adhesion study of 1-μm negatively charged silica spheres onto these functionalized surfaces indicates that by varying the molecular weight, the adhesion threshold can be changed. System modeling is being conducted to support experimental observations.

京都大学 / 新制・課程博士 / 博士(医学) / 甲第24286号 / 医博第4902号 / 新制||医||1061(附属図書館) / 京都大学大学院医学研究科医学専攻 / (主査)教授 森本 尚樹, 教授 辻川 明孝, 教授 渡邉 大 / 学位規則第4条第1項該当 / Doctor of Medical Science / Kyoto University / DFAM

The purpose of this study is to build, test, validate, and implement two heat transfer models, and couple them to an existing fluid flow solver, which can then be used for simulating multi-disciplinary problems. The first model is for heat conduction computations, the other one is a quasi-one-dimensional cooling channel model for water-cooled jacket structural analysis. The first model employs the integral, conservative form of the thermal energy equation, which is discretized by means of a finite-volume numerical scheme. A special algorithm is developed at the interface between the solid and fluid regions, in order to keep the heat flux consistent. The properties of the solid region materials can be temperature dependent, and different materials can be used in different parts of the domains, thanks to a multi-block gridding strategy. The cooling channel flow model is developed by using uasi-one-dimensional conservation laws of mass, momentum, and energy, taking into account the effects of heat transfer and friction. It is possible to have phase changes in the channel, and a mixture model is applied, which allows two phases to be present, as long as they move at the same bulk velocity and vapor quality does not exceed relatively small values. The coupling process of both models (with the fluid solver and with each other) is handled within the Loci system, and is detailed in this study. A hot-air nozzle wall problem is simulated, and the computed results are validated with available experimental data. Finally, a more complex case involving the water-cooled nozzle of a Rocket Based Combined Cycle(RBCC) gaseous oxygen/gaseous hydrogen thruster is simulated, which involves all three models, fully coupled. The calculated temperatures in the nozzle wall and at the cooling channel outlet compare favorably with experimental data.

The current research investigates the use of solid-embedded thermocouples for determining accurate transient temperature measurements within a solid medium, with emphasis on measurements intended for use in inverse heat conduction problems. Metal casting experiments have been conducted to collect internal mold temperatures to be used, through inverse conduction methods, to estimate the heat exchange between a casting and mold. Inverse conduction methods require accurate temperature measurements for valid boundary estimates. Therefore, various sources of thermocouple measurement uncertainty are examined and some suggestions for uncertainty reduction are presented. Thermocouple installation induced bias uncertainties in experimental temperature data are dynamically corrected through the development and implementation of an embedded thermocouple correction (ETC) transfer function. Comparisons of experimental data to dynamically adjusted data, as well as the inverse conduction estimates for heat flux from each data set, are presented and discussed.