Dans la pratique actuelle du génie géotechnique, les essais de pénétration tels que les CPT, SPT, Panda sont largement utilisés pour caractériser mécaniquement les sols, au travers notamment d’une caractéristique de rupture appelée résistance de pointe. Par ailleurs, les dernières évolutions technologiques apportées aux essais de pénétration dynamique (Panda 3) permettent d’obtenir pendant chaque impact une courbe charge–enfoncement donnant la charge en pointe en fonction de l’enfoncement à partir de la mesure et du découplage des ondes générées durant l’essai. L’exploitation de cette nouvelle courbe fournit des informations non seulement sur la résistance de pointe dynamique mais également sur des paramètres mécaniques complémentaires mis en jeu pendant l’enfoncement de la pointe. L’objectif de cette thèse est de développer un modèle numérique en 2D capable de reproduire les signaux pénétrométriques obtenus expérimentalement par essais de type statique ou dynamique. Ce modèle est basé sur la méthode des éléments discrets avec une loi de contact linéaire simple. Une fois le modèle validé, une étude paramétrique a été réalisée en jouant essentiellement sur les modes d’application de la sollicitation (vitesse d’impact ou de pénétration), la granulométrie du matériau ainsi que l’arrangement granulaire (variation de la densité). Outre l’influence de ces paramètres sur les signaux pénétrométriques et la résistance de pointe mesurée, une attention particulière est portée sur l’analyse micromécanique : dissipation d’énergie dans le milieu, évolution des chaines de force, orientations des contacts. Cette analyse nécessite de développer des outils numériques spécifiques afin de mieux comprendre le mécanisme de l’enfoncement et tenter d’expliquer la réponse mécanique macroscopique obtenue. L’effet de la vitesse n’influence significativement que sur les essais de pénétration statiques et dynamiques en régime d’écoulement dense. A vitesse d’enfoncement comparable, il n’y a aucune différence significative au niveau microscopique entre les deux modes de sollicitation statique et dynamique. En ce qui concerne l’influence des caractéristiques du matériau, les résultats obtenus par le modèle numérique conforment aux celui réel lors que le frottement entre particules ou la compacité du milieu varie. Concernant la granulométrie, la variation de la courbe charge-enfoncement et la force de pointe dynamique augmente lorsque le diamètre moyen augmente. / In the field of in situ mechanical characterization of soils, penetration tests are commonly used. Penetration tests measure the properties of soils in the domain of large deformations. The tip resistances, deduced from pile driving theory, can be measured either in dynamic conditions (q d ) either in static conditions (q c ). Recently, the measurement technique in dynamic conditions has been improved and it is now possible to record the whole response of the soil during one impact in terms of tip force and penetration distance. The exploitation of this new curve provides information not only on dynamic tip resistance but also on additional mechanical parameters involved during the driving of the tip. The objective of this work is to develop a numerical model in 2D able to reproduce the penetrometric record obtained experimentally by static or dynamic penetration tests. This model is based on the discrete element method with a simple linear contact model. After the validation of the model, a parametric study was performed essentially on the loading type (static or dynamic), the penetration rate, the particle size of the granular material and the arrangement (density variation). Besides the influence of these parameters on the penetrometer signals and the tip resistance, a particular attention was focused on micromechanical analysis: energy dissipation in the medium, force chain evolution, contact orientation. This analysis requires the development of specific numerical tools to better understand the penetration mechanism and try to explain the macroscopic mechanical response obtained. The penetration rate influences significantly only in the dense flow regime on the static and dynamic penetration tests. There is no significant microscopic difference between static and dynamic penetration tests with similar penetration rates. Regarding the influence of the characteristics of the material, the numerical results obtained conform to the real results when the particle friction or the compactness of the medium varies. Concerning the particle size, the dynamic signal variation and the dynamic tip force increases when the average particle diameter increases.

The knowledge about the shear strength of a soil is important because it is a key parameter that is used in many calculations in construction engineering. Some examples of what’s possible to calculate are slope stability, the soil pressure against retaining walls and the carrying capacity of building foundations. Great economic losses or, in the worst case scenario the risk for human lives, could be the result if the geotechnical properties of the soil are ignored. This report considers the undrained shear strength of clay from Uppsala. There are different methods based on empirical experiences which are used to determine the undrained shear strength of a clay. In this project the methods and the results in undrained shear strength are compared between CPT-probing, which is carried out in-situ, and the drop cone test which is done in a laboratory. The reason for this comparison is that they usually don’t show the same results.The tests had already been made before this project started and therefore it is only the comparison of the results between the methods that has been done. The comparison was done by creating charts in Excel where the results from CPT and the drop cone test from was put together from the same point. The shear strength values from the methods were also statistically analysed with a t-test to see if they show the same hypothetical expected value with 95 % significance in every test point / Kunskap om skjuvhållfastheten är viktig då den används för beräkningar inom byggoch anläggningsbranschen. Exempel på vad som kan beräknas är släntstabilitet, jordtrycket mot en spont eller bärförmågan hos en byggnadsgrund. Stora ekonomiska förluster och i värsta fall fara för människoliv kan bli resultatet om jordens geotekniska egenskaper ignoreras. Denna rapport tar upp den odränerade skjuvhållfastheten i Uppsalalera. Det finns olika metoder som bygger på empiriska erfarenheter som kan användas för att ta reda på den odränerade skjuvhållfastheten i lera. I föreliggandeprojekt jämförs metoderna och resultaten i odränerad skjuvhållfasthet mellan CPT-sondering som utförs in-situ och fallkonförsök som utförs på lerprover i ett laboratorium. Anledningen till studien är att metoderna inte alltid ger samma mätvärden. Undersökningarna utfördes innan projektet började. Jämförelsen har gjorts genom den statistiska jämförelsen t (student)-test. Resultatet från t-testet visar att skjuvhållfasthetsvärdena från CPT respektive fallkonförsöken från samma undersökningspunkt och från samma nivå har samma hypotetiska förväntade värde på 95 % signifikansnivå. Genom sammanställda grafer syns att metoderna i de flesta fall överensstämmer till ett djup på minst 20 m.

This study examines the use of performance-based engineering in earthquake liquefaction hazard analysis with Cone Penetration Test data (CPT). This work builds upon previous research involving performance-based liquefaction analysis with the Standard Penetration Test (SPT). Two new performance-based liquefaction triggering models are presented herein. The two models used in this liquefaction analysis are modified from the case-history based probabilistic models proposed by Ku et al. (2012) and Boulanger and Idriss (2014). Using these models, a comparison is made between the performance-based method and the conventional pseudo-probabilistic method. This comparison uses the 2014 USGS probabilistic seismic hazard models for both methods. The comparison reveals that, although in most cases both methods predict similar liquefaction hazard using a factor of safety against liquefaction, by comparing the probability of liquefaction, the performance-based method on average will predict a smaller liquefaction hazard.

As a consequence of the 2010 – 2011 Canterbury earthquake sequence, Christchurch experienced widespread liquefaction, vertical settlement and lateral spreading. These geological processes caused extensive damage to both housing and infrastructure, and increased the need for geotechnical investigation substantially. Cone Penetration Testing (CPT) has become the most common method for liquefaction assessment in Christchurch, and issues have been identified with the soil behaviour type, liquefaction potential and vertical settlement estimates, particularly in the north-western suburbs of Christchurch where soils consist mostly of silts, clayey silts and silty clays. The CPT soil behaviour type often appears to over-estimate the fines content within a soil, while the liquefaction potential and vertical settlement are often calculated higher than those measured after the Canterbury earthquake sequence. To investigate these issues, laboratory work was carried out on three adjacent CPT/borehole pairs from the Groynes Park subdivision in northern Christchurch. Boreholes were logged according to NZGS standards, separated into stratigraphic layers, and laboratory tests were conducted on representative samples. Comparison of these results with the CPT soil behaviour types provided valuable information, where 62% of soils on average were specified by the CPT at the Groynes Park subdivision as finer than what was actually present, 20% of soils on average were specified as coarser than what was actually present, and only 18% of soils on average were correctly classified by the CPT. Hence the CPT soil behaviour type is not accurately describing the stratigraphic profile at the Groynes Park subdivision, and it is understood that this is also the case in much of northwest Christchurch where similar soils are found. The computer software CLiq, by GeoLogismiki, uses assessment parameter constants which are able to be adjusted with each CPT file, in an attempt to make each more accurate. These parameter changes can in some cases substantially alter the results for liquefaction analysis. The sensitivity of the overall assessment method, raising and lowering the water table, lowering the soil behaviour type index, Ic, liquefaction cutoff value, the layer detection option, and the weighting factor option, were analysed by comparison with a set of ‘base settings’. The investigation confirmed that liquefaction analysis results can be very sensitive to the parameters selected, and demonstrated the dependency of the soil behaviour type on the soil behaviour type index, as the tested assessment parameters made very little to no changes to the soil behaviour type plots. The soil behaviour type index, Ic, developed by Robertson and Wride (1998) has been used to define a soil’s behaviour type, which is defined according to a set of numerical boundaries. In addition to this, the liquefaction cutoff point is defined as Ic > 2.6, whereby it is assumed that any soils with an Ic value above this will not liquefy due to clay-like tendencies (Robertson and Wride, 1998). The method has been identified in this thesis as being potentially unsuitable for some areas of Christchurch as it was developed for mostly sandy soils. An alternative methodology involving adjustment of the Robertson and Wride (1998) soil behaviour type boundaries is proposed as follows:  Ic < 1.31 – Gravelly sand to dense sand  1.31 < Ic < 1.90 – Sands: clean sand to silty sand  1.90 < Ic < 2.50 – Sand mixtures: silty sand to sandy silt  2.50 < Ic < 3.20 – Silt mixtures: clayey silt to silty clay  3.20 < Ic < 3.60 – Clays: silty clay to clay  Ic > 3.60 – Organics soils: peats. When the soil behaviour type boundary changes were applied to 15 test sites throughout Christchurch, 67% showed an improved change of soil behaviour type, while the remaining 33% remained unchanged, because they consisted almost entirely of sand. Within these boundary changes, the liquefaction cutoff point was moved from Ic > 2.6 to Ic > 2.5 and altered the liquefaction potential and vertical settlement to more realistic ii values. This confirmed that the overall soil behaviour type boundary changes appear to solve both the soil behaviour type issues and reduce the overestimation of liquefaction potential and vertical settlement. This thesis acts as a starting point towards researching the issues discussed. In particular, future work which would be useful includes investigation of the CLiq assessment parameter adjustments, and those which would be most suitable for use in clay-rich soils such as those in Christchurch. In particular consideration of how the water table can be better assessed when perched layers of water exist, with the limitation that only one elevation can be entered into CLiq. Additionally, a useful investigation would be a comparison of the known liquefaction and settlements from the Canterbury earthquake sequence with the liquefaction and settlement potentials calculated in CLiq for equivalent shaking conditions. This would enable the difference between the two to be accurately defined, and a suitable adjustment applied. Finally, inconsistencies between the Laser-Sizer and Hydrometer should be investigated, as the Laser-Sizer under-estimated the fines content by up to one third of the Hydrometer values.

Liquefaction-induced lateral spread displacements cause severe damage to infrastructure, resulting in large economic losses in affected regions. Predicting lateral spread displacements is an important aspect in any seismic analysis and design, and many different methods have been developed to accurately estimate these displacements. However, the inherent uncertainty in predicting seismic events, including the extent of liquefaction and its effects, makes it difficult to accurately estimate lateral spread displacements. Current conventional methods of predicting lateral spread displacements do not completely account for uncertainty, unlike a performance-based earthquake engineering (PBEE) approach that accounts for the all inherent uncertainty in seismic design. The PBEE approach incorporates complex probability theory throughout all aspects of estimating liquefaction-induced lateral spread displacements. A new fully-probabilistic PBEE method, based on results from the cone penetration test (CPT), was created for estimating lateral spread displacements using two different liquefaction triggering procedures. To accommodate the complexity of all probabilistic calculations, a new seismic hazard analysis tool, CPTLiquefY, was developed. Calculated lateral spread displacements using the new fully-probabilistic method were compared to estimated displacements using conventional methods. These comparisons were performed across 20 different CPT profiles and 10 cities of varying seismicity. The results of this comparison show that the conventional procedures of estimating lateral spread displacements are sufficient for areas of low seismicity and for lower return periods. However, by not accounting for all uncertainties, the conventional methods under-predict lateral spread displacements in areas of higher seismicity. This is cause for concern as it indicates that engineers in industry using the conventional methods are likely under-designing structures to resist lateral spread displacements for larger seismic events.

Liquefaction-induced lateral spread displacements cause severe damage to infrastructure, resulting in large economic losses in affected regions. Predicting lateral spread displacements is an important aspect in any seismic analysis and design, and many different methods have been developed to accurately estimate these displacements. However, the inherent uncertainty in predicting seismic events, including the extent of liquefaction and its effects, makes it difficult to accurately estimate lateral spread displacements. Current conventional methods of predicting lateral spread displacements do not completely account for uncertainty, unlike a performance-based earthquake engineering (PBEE) approach that accounts for the all inherent uncertainty in seismic design. The PBEE approach incorporates complex probability theory throughout all aspects of estimating liquefaction-induced lateral spread displacements. A new fully-probabilistic PBEE method, based on results from the cone penetration test (CPT), was created for estimating lateral spread displacements using two different liquefaction triggering procedures. To accommodate the complexity of all probabilistic calculations, a new seismic hazard analysis tool, CPTLiquefY, was developed. Calculated lateral spread displacements using the new fully-probabilistic method were compared to estimated displacements using conventional methods. These comparisons were performed across 20 different CPT profiles and 10 cities of varying seismicity. The results of this comparison show that the conventional procedures of estimating lateral spread displacements are sufficient for areas of low seismicity and for lower return periods. However, by not accounting for all uncertainties, the conventional methods under-predict lateral spread displacements in areas of higher seismicity. This is cause for concern as it indicates that engineers in industry using the conventional methods are likely under-designing structures to resist lateral spread displacements for larger seismic events.

No description available.

Cone penetration in sands is a complex process: it contains several challenges that geomechanicians face, such as large displacements, large strains, strain localization, and microscale phenomena such as particle crushing and sand fabric evolution. In order to gain a deeper understanding of the penetration process and the mechanisms controlling penetration resistance, capturing these displacement and strain fields and microscale phenomena is necessary. Furthermore, as more sophisticated theoretical models become available for the simulation of the cone penetration problem, the experimental validation of those methods becomes vital.<br><div><br></div><div>This dissertation presents a multiscale study of the cone penetration process in silica sands. The penetration problem is investigated using a combinational approach consisting of calibration chamber experiments, digital image correlation (DIC) analysis, and X-ray computed Tomography (XCT) scans. Three silica sands with different particle characteristics are used in the experimental program. These three sands have similar particle size distributions; however, they differ in particle morphologies and particle strengths. These differences allow a study of the effect of microscale sand properties on the macroscale response of the sands to the cone penetration process. The three silica sands used in this research are fully characterized using laboratory experiments to obtain particle size distributions, particle morphologies, particle crushing strengths, minimum and maximum packing densities, and critical-state friction angles. Subsequently, both dense and medium-dense samples of the three sands are compressed in a uniaxial loading device placed inside an X-ray microscope (XRM) and scanned at multiple stress levels during uniaxial compression. Results from uniaxial compression experiments indicate that: (1) the compressibility of the sands is closely tied to particle morphology and strength, and (2) the anisotropy in the orientations of interparticle contact normals generally increases with axial stress; however, this increase is limited by the occurrence of particle crushing in the sample.<br></div><div><br></div><div>Subsequently, cone penetration experiments are performed under different confinement levels on dense samples of the three sands in aspecial half-cylindrical calibration chamber equipped with DIC capabilities. For each penetration experiment, incremental displacement fields around the cone penetrometer are obtained using DIC analysis, and these incremental displacement fields are further analyzed to compute the incremental strain fields. A novel methodology is developed to obtain the shear-band patterns that develop around the penetrometer automatically. Furthermore, differences in the shear-band patterns in deep and shallow penetration environments are also investigated. Results show that strain fields tend to localize intensely near the penetrometer tip, and the shear bands tend to develop along the inclined face and near the shoulder of the penetrometer. Significant differences in the shear band patterns in deep and shallow penetration environments are also observed.<br></div><div><br></div><div>After each cone penetration experiment, a specially developed agar-impregnation technique is used to collect minimally disturbedsand samples from around the penetrometertip. These agar-impregnated sand samples are scanned in the XRM to obtain 3D tomography data, which are further analyzed to quantify particle crushing around the penetrometer tip. The results show that: (1) for a given sample density, the amount of crushing around the cone penetrometer depends on the confinement and the sand particle characteristics, (2) the level of crushing is not uniform around the penetrometer tip, with more severe crushing observed near the shoulder of the penetrometer, and (3) the regions with more severe particle crushing around the penetrometer approximately overlap with regions of high shear strain and volumetric contraction. A framework is also proposed to obtain the ratio of penetration resistance in more crushable sands to penetration resistance in less crushable sands. Furthermore, a novel resin-impregnation technique is also developed to collect undisturbedsand samples from around the penetrometer tip. The resin-impregnated sand sample collected after one of the penetration experiments is scanned in the XRM to obtain the 3D tomography data, which is then analyzed to obtain the distribution of interparticle contact normal orientations at multiple locations around the penetrometer tip. These analyses indicate that the interparticle contact normals tend to orient themselves with the incremental principal strains around the penetrometer: below the penetrometer tip, the interparticle contact normals orient vertically upwards, while closer to the shoulder of the penetrometer, the interparticle contact normals become more radially inclined.<br></div><div><br></div><div>Data presented in this dissertation on penetration resistance, incremental displacement fields, incremental strain fields, particle crushing, and interparticle contact normal orientations around the cone penetrometer are aimed to be useful to researchers working on the multiscale modeling of penetration processes in granular materials and aid in the further development of our understanding of penetration processes in sands.<br></div>

This study assessed implementation status of collaborative TB/HIV services in Addis Ababa City Administration aiming to promote better implementation strategies. The study employed mixed research methods and was descriptive. The study design used both quantitative and qualitative data using structured questionnaires and semi-structured interview guides, respectively. The study population for the quantitative design included 1,683 TB/HIV patients from 10 conveniently selected health facilities: Zewditu and Menelik Hospitals, health centres of Lideta, Yeka, Kazanchis, NifaSilk-Lafto-No1, Woreda-7, Kality, Bole and Gulele. All the patients who were on their follow-up cares during the data collection period were interviewed. Participants for qualitative design were 1,650 TB/HIV patients for short answered questions; 8 FGDs among patients; interview of 10 TB/HIV care facility coordinators/health workers and one regional TB/HIV care coordinator, all purposively selected. Quantitative data was analysed using SPSS 15.0, while qualitative data were thematically analysed manually. Majority of HIV patients (92.8%) self-reported that they had been screened for TB; of which, 11.2% were diagnosed for active TB during their follow-up cares. Whereas, 87.1% of TB patients had been offered for HIV test; 79.8% tested; 20.2% tested positive. Knowledge on TB and HIV diseases, transmission and prevention was found to be low. However, participants appreciated the support of the healthcare delivery system in improving their health. Collaborative TB/HIV activities brought additional on-the-job training for healthcare workers; improved flow of logistics and re-arrangement of infrastructures of facilities. The study revealed that, implementation of collaborative TB/HIV activities in Addis Ababa need boosting. The study recommends the need for coordinated efforts of all stakeholders for improving implementation of collaborative TB/HIV care services, as identified by this study. The contribution of this study developed pocket-guide for healthcare workers on collaborative TB/HIV care services, which provides guidance in promoting better TB/HIV care / Health Studies / D. Litt. et Phil. (Health Studies)

This thesis is a user study within library and information science on participatory practices of a professional group in work activity. This has been investigated only to a minor extent in previous library and information science research. The qualitative empirical focus alternates between physicians‟ engagements in work practice and workplace learning within patient care. The overall research problem was to learn how people in workplaces interacted with information that was embedded, intricately intertwined, and tightly bound to the ongoing routines of their everyday work. This thesis aims at understanding information practices of professionals in occupational settings as exemplified by a team of physicians in a Nigerian teaching hospital. In this thesis, the focus was on the collective work activity, and the specific goals identified include how physicians interact and make meaning in the context of the social activities in the workplace, how professionals individually or collectively gather, understand, produce, share and use information, and how workplace learning influences information practices. Information practices are viewed as sociocultural practices that occur inside other practices. The thesis focuses on a nuanced, contextualized understanding of the interplay between the participating actors in activity, the activity per se, and the intermediary role of tools and artefacts. The epistemological point of departure is the sociocultural perspective that emphasizes the dynamic interdependence of the individual with the social and collective development focusing on mediation through tools and artefacts in cultural, institutional, and historical situations. I have chosen cultural-historical activity theory and the practice theories to analyse the dynamic processes in the context of patient care. Their underlying principles guided the empirical study, facilitating extrapolations and illustrations in the analysis. The cultural-historical activity theory was used to understand contextual issues that influence information practices in work activity: the object and subject of activity, division of labour, rules and norms, community, tools and artefacts, as well as the activity system itself and the hierarchical structure of the activity. Theories and concepts employed from a practice perspective on learning were considered useful for understanding the participatory modes in workplace and the influence of social learning communities on diverse information processes. In so doing, the study strives to provide a holistic understanding of information practices, workplace learning, and the relationships between them.The empirical data was gathered through a qualitative case study that lasted over a period of two years. Direct observation was the dominant data collection technique 5 used throughout the preliminary and main empirical studies to capture physicians‟ information practices and experiences. The observation focused on the Clinical Pharmacology and Therapeutics (CPT) team‟s encounters with patients; the interactions they had amongst themselves, and events and situations surrounding patient care. During the main study, other data collection techniques were employed alongside the observation method. In-depth open-ended interviews were conducted with 17 physicians and 9 non-physicians who were selected to provide rich and varied descriptions of the phenomena under study. The interview time totalled at 1,535 minutes. Physical artefacts were another data collection technique employed: 30 patients‟ medical records were assessed during the empirical study. Finally, informal interactions in the research setting were an additional data collection technique used continuously throughout the two empirical periods. The results were analyzed through a combination of inductive and deductive methods of analysis. There are four parts to the empirical results in this thesis. In the first, contextual elements that showed how work environment can be an influencing factor in the information practices of a professional group are described from the perspective of cultural historical activity theory. In the second part, the nature of information access in the real-world information environment was portrayed. It was found that information sources and strategies contributed to the overarching goal of restoring patient health to normalcy. The information sources and strategies were also found useful for mediating the information environment both subjectively and intersubjectively. An equally important result concerns the authority issues related to information sources and strategies. In the third part, available tools and artefacts were presented as useful information aids that also played a mediating role. Tools were categorised into physical tools and language. Language was categorized according to the social situations or classes of speakers. The case notes were seen as useful artefact and occupied a central niche in the studied work activity. These tools and artefacts enabled affordances around which social practices were built on in the work activities. In the last part of the results, various information practices that mirror the participatory practices rather than those of isolated individuals are highlighted. Six dimensions made up and covered the most vital spectrum of the information processing: information gathering, meaning making, information sharing, information use, reading, and documentation. Furthermore, the study revealed that learning took place simultaneously with the work activity and that it influenced information practices at the same time. / <p>Academic dissertation for the Degree of Doctor of Philosophy in Library and Information Science at the University of Borås to be publicly defended on Friday 19 October 2012 at 13.00 in lecture room D 211, University of Borås, Allégatan 1, Borås.</p>