Rammed earth is one of the earliest building materials used for structural walls. Stabilised rammed earth is a variant of traditional or pure rammed earth that involves addition of a small amount of cement to improve strength and durability. Rammed earth buildings experience in-plane shear forces as well as flexural stresses due to out-of-plane bending especially during earthquakes. The thesis attempts to examine the behaviour of cement stabilised rammed earth wall elements and building models subjected to lateral loads. A brief introduction to rammed earth construction followed by a review of literature on rammed earth and details of the existing codes of practice on rammed earth is provided in Chapter 1. Chapter 2 deals with the flexural strength, modulus of rupture, stress-strain relationships and free vibration characteristics of cement stabilised rammed earth (CSRE) in greater detail. Properties of raw materials used in the experimental investigations followed by a detailed description of the experimental programme, method of preparation of various types of specimens and their testing procedures are provided. Flexure strength and modulus of rupture were determined in both the orthogonal directions. Influence of (a) thickness of the specimen, (b) direction of compacted layers with respect to the flexural tension developed and (c) effect of cement slurry coating between the compacted layers on the flexural strength of CSRE were examined. The investigations show that flexure strength increases with the increase in the specimen thickness and a coat cement slurry on the compacted layers leads to improvement in flexure strength. The flexural strength parallel to compacted layers is higher when compared to flexure strength perpendicular to compacted layers. Stress-strain relationships show that the initial tangent modulus of CSRE in saturated condition is about 60% of that in dry condition. Damping ratio as obtained from the free vibration studies is found to be 0.022 in the two orthogonal directions. Dynamic characteristics of CSRE building models are presented in Chapter 3. A simple alternative to shake table called as “Shock Table” was used in the present investigation for providing base motion to the building model. A half-scale CSRE building model with R.C lintels only above door and window openings (with no earthquake resistant features) was constructed on the Shock Table. The wall thickness of the building model was 100 mm. Procedure for construction, instrumentation and testing of the CSRE building model is presented. Responses measured and damages observed are discussed in detail. Finite element (FE) analyses were performed on six different building models with different earthquake resistant features using commercially available FE software (NISA V17). Both free vibration and forced vibration analyses were performed. Natural frequencies and forced vibration responses (acceleration) of building model (BM1) obtained from experiment and FE analysis were compared. Responses (free vibration and forced vibration) of other five building models were predicted using FE analysis. Crack patterns of the building models with roof and without roof are compared. The thesis ends with a summary of the results and concluding remarks in Chapter 4.

The focus of the proposed research will be on exploring the use of nanotechnology-based nano-filaments, such as carbon nanotubes (CNTs) and nanofibers (CNFs), as reinforcement in improving the mechanical properties of portland cement paste as a construction material. Due to their ultra-high strength and very high aspect ratios, CNTs and CNFs have been used as excellent reinforcements in enhancing the physical and mechanical properties of polymer, metallic, and ceramic composites. Very little attention has been devoted on exploring the use of nano-filaments in the transportation industry. Therefore, this study aims to bridge the gap between nano-filaments and transportation materials. This will be achieved by testing the integration of CNTs and CNFs in ordinary portland cement paste through state-of-the-art techniques. Different mixes in fixed proportions (e.g. water-to-cement ratio, air content, admixtures) along with varying concentrations of CNTs or CNFs will be prepared. Different techniques commonly used for other materials (like polymers) will be used in achieving uniform dispersion of nano-filaments in the cement paste matrix and strong nano-filaments/cement bonding. Small-scale specimens will be prepared for mechanical testing in order to measure the modified mechanical properties as a function of nano-filaments concentration, type, and distribution. With 0.1 percent CNFs, the ultimate strain capacity increased by 142 percent, the flexural strength increased by 79 percent, and the fracture toughness increased by 242 percent. Furthermore, a scanning electron microscope (SEM) is used to discern the difference between crack bridging and fiber pullout. Test results show that the strength, ductility, and fracture toughness can be improved with the addition of low concentrations of either CNTs or CNFs.

In 1995, the Swedish government recommended the discontinuation of amalgam as restorative in paediatric dentistry. Because the mercury content in amalgam constitutes an environmental hazard, its use has declined. The use of resin composites is increasing, but the polymerisation shrinkage of the material is still undesirably high, and the handling of uncured resin can cause contact dermatitis. A new restorative material has recently been developed in Sweden as an alternative to amalgam and resin composite: a calcium aluminate cement (CAC). CAC has been marketed as a ceramic direct restorative for posterior restorations (class I, II) and for class V restorations. This thesis evaluates mechanical properties and clinical durability of the calcium aluminate cement when used for class II restorations. Hardness, in vitro wear, flexural strength, flexural modulus, and surface roughness were evaluated. A scanning electron replica method was used for evaluation of the interfacial adaptation to tooth structures in vivo. The durability was studied in a 2-year intra-individually clinical follow-up of class II restorations. Major results and conclusions from the studies are as follows: • The CAC was a relatively hard material, harder than resin-modified glass ionomer cement but within the range of resin composites. The CAC wore less than resin-modified glass ionomer cement but more than resin composite. • Flexural strength of CAC was in the same range as that of zinc phosphate cement and far below that of both resin composite and resin-modified glass ionomer cement. Flexural modulus of CAC was higher than both resin composite and resin-modified glass ionomer cement. The low flexural strength of CAC precludes its use in stress-bearing areas. • Surface roughness of CAC could be decreased by several polishing techniques. • For CAC restorations, interfacial adaptation was higher to dentin but lower to enamel compared with resin composite restorations. Fractures were found perpendicular to the boarders of all CAC restorations and may indicate expansion of the material. • After 2 years of clinical service, the class II CAC restorations showed an unacceptably high failure rate. Material fractures and tooth fractures were the main reasons for failure.

Rock grouting is performed to decrease the hydraulic conductivity around underground structures, such as tunnels and caverns. Cement grouts are often used and pumped into joint and fractures of the rock formation. Piston type pumps are mostly used for high pressure rock grouting. A pulsation effect is inevitable when using this type of pump due to the movement of the piston. The effect of this pulsation on rock grouting is yet to be known but believed to be benefi-cial for the penetration of the grout. Current flow meters used in the field are not accu-rate enough to determine the fluctuation of the flow rate when it is less than 1 l/min. In addition, currently available flow meters measure the average of the flow over a cer-tain period of time, hence the true fluctuation of the flow rate due to the pulsation of the piston remains unknown. In this paper, a new methodology, the so called ‘Ultrasound Velocity Profiling – Pressure Difference’ (UVP+PD) method has been introduced to show the pulsation effect when using a piston type pump. The feasibility of this method was successfully investigated for the direct in-line determination of the rheological properties of micro cement based grouts under field conditions (Rahman &amp; Håkansson, 2011). Subse-quently, it was also found that this method can be very efficient to measure the fluctu-ation of the flow rate for different types of pumps. From a grouting point of view the UVP+PD method can be used to synchronize the pressure and flow of a piston type pump by measuring the pulsation effect. Conse-quently it can be used as a tool for the efficiency and quality control of different types of pumps. / <p>QC 20121221</p>

In the life of a well, the cement sheath not only provides zonal isolation but also supports casing and increases casing-collapse resistance. Due to the high-pressure, high-temperature (HPHT) conditions, the cement sheath plays an important role in maintaining wellbore integrity. During the production process in HPHT wells, the pressure differential inside the casing and the surrounding formation is larger than the conventional wells. The stress induced by fluid withdrawal in highly compact reservoirs can cause the cement and the casing failure in these wells. These present a greater challenge to the wellbore integrity than the conventional wells. To have reliable data, extensive experimental work on Class G cement was carried out to measure the principal parameters for mechanical structural calculations. The experiment was also set up to simulate conditions under which cement low-cycle fatigue failure could occur. Zero-based cyclic pressure was applied to the casing in the cement low-cycle fatigue test. Three types of cement (72-lbm/ft3, 101-lbm/ft3 and 118-lbm/ft3) were cured and tested at 300ºF to study the cement mechanical properties under high-temperature conditions over the long term. The tests included a 1-year mechanical properties measurement such as compressive strength development; i.e., Young’s modulus and Poisson’s ratio. Finite element methods (FEM) were used to study the casing buckling deformation characteristics of reservoir compaction in some south Texas wells. The 2D and 3D FEM models were built to study the effects of mechanical properties and reservoir compaction on HPHT well integrity. As the confining pressure increases, the cement shows more plasticity and can withstand more pressure cycles. The cement with a higher Poisson’s ratio and lower Young’s modulus showed better low-cycle fatigue behavior. Casing collapse resistance is very sensitive to void location, cement Poisson’s ratio, cement Young’s modulus, and pore pressure. Casing eccentricity and voids shape have minor effect on the casing-collapse resistance. Casing shear failure, tension failure, and buckling failure are the most likely failure modes in reservoir compaction. For different casing wall thickness, the critical buckling strain is almost identical. This study presents a better understanding of casing failure and cement failure in HPHT wells. The results of the study will help improve cement and casing design to maintain wellbore integrity that can in turn be expected to extend throughout the life of the well.

The present research seeks to study the decrease in diffusivity rate as relative humidity (RH) decreases and modeling drying shrinkage of hardened cement paste as a poroviscoelastic respose. Thin cement paste strips of 0.4 and 0.5 w/c at age 3 and 7 days were measured for mass loss and shrinkage at small RH steps in an environmental chamber at constant temperature. Non-linear drying diffusion rate of hardened cement was modeled with the use of Fick's second law of diffusion by assuming linearity of diffusion rate over short drops of ambient relative humidity. Techniques to determine drying isotherms prior to full equilibration of mass loss, as well as converting mass loss into concentration of water vapor were developed. Using the measured water vapor diffusivity, drying shrinkage strain was modeled by the theory of poroviscoelasticity. This approach was validated by determining viscoelastic properties from uniaxial creep tests considering the effect of aging by the solidification theory. A change in drying diffusion rate at different RH was observed in the 0.4 and 0.5 w/c pastes at different ages. Drying diffusion rate decreases as RH drops. This can be attributed to a change in diffusion mechanisms in the porous media at smaller pore radius. Shrinkage modeling with an average diffusion coefficient and with determined viscoelastic parameters from creep tests agreed well compared to the shrinkage data from experiments, indicating that drying shrinkage of cement paste may be considered as a poroviscoelastic reponse.

¡uStructure Reinforcement¡v is necessary when the load of a building or bridge has exceeded that for which it was originally designed. Reinforcement is required when there are changes in the function of a building, poor or incorrect design, flood or earthquake damage, revision of government regulations resulting in new specifications for construction materials, or changes in job practices. The concept of structure reinforcement developed in Japan in the 1970¡¦s, and was introduced into Taiwan at the end of the decade. Short operating times, high strength, and economy of space are among the advantages which make the concept attractive. Higher cost, however, has slowed its implementation. The current ratio of new to reinforced construction in developing countries is 6:4; in developed countries 4:6. As Taiwan is now considered a developed country lacking land resources but with strict building regulations, structure reinforcement is more and more in demand. China, on the other hand, is still ranked a developing country, but, due to the current construction boom and weak infrastructure, recent structures often need reinforcement. During the design and calculation of structure reinforcement, the usual choice of reinforcing materials is epoxy resin, special cement, carbon fiber sheets, and carbon steel plates. SB Construction is a medium sized company subject to the natural rise and fall in construction demand. In the past, SB used only special cement as reinforcement material as it had no production line for epoxy resin or carbon fiber steel. This report concerns itself mainly with how, from a business angle, environment analysis and internal management ability can establish a competitive advantage adapted to its own business model and how to evaluate the effectiveness of this strategy. Section One: background and motivation for research, purpose and structure. Section Two: research design, discussion of theory, method and procedures. Section Three: industry analysis, development of structure reinforcement, analysis and comparison of Taiwan and China, and analysis of superior products. Section Four: case study, introduction to the company, changes in strategy, expectations and goals. Last: conclusion and suggestions for adapting to changes in the environment, discussion of strategies for future consideration and further development.

The need for economical, sustainable, safe, and secure shelter is an inherent global problem and numerous challenges remain in order to produce environmentally friendly construction products which are structurally safe and durable. The use of sisal, a natural fiber with enhanced mechanical performance, as reinforcement in a cement based matrix has shown to be a promising opportunity. This work addresses the development and advances of strain hardening cement composites using sisal fiber as reinforcement. Sisal fibers were used as a fabric to reinforce a multi-layer cementitious composite with a low content of Portland cement. Monotonic direct tensile tests were performed in the composites. The crack spacing during tension was measured by image analysis and correlated to strain. Local and global deformation was addressed. To demonstrate the high performance of the developed composite in long term applications, its resistance to tensile fatigue cycles was investigated. The composites were subjected to tensile fatigue load with maximum stresses ranging from 4 to 9.6 MPa at a frequency of 2 Hz. The composites did not fatigue below a maximum fatigue level of 6 MPa up to 106 cycles. Monotonic tensile testing was performed for composites that survived 106 cycles to determine its residual strength.

Thesis (M. Phil.)--Hong Kong University of Science and Technology, 2003. / Includes bibliographical references (leaves 213-216). Also available in electronic version. Access restricted to campus users.

Calcium aluminate cement (CAC) is a rapid hardening cementitious material often used in niche concrete repairs where high early-age strength and robust durability are required. This research project characterized the implications of the additions of various mineral and chemical admixtures to plain CAC to mitigate strength reductions associated with conversion, an inevitable strength reduction associated with the densification of metastable hydrates (CAH10 and C2AH8) to stable hydrates (C3AH6 and AH3). The effect of these admixtures on early-age strength development, volume change, and the correlation to macro-scale performance were reported in this dissertation. Various mixtures of CAC were investigated including: pure CAC, binary blends of CAC with fly ash (Class C) or CaCO3, and ternary blends of CAC with slag and silica fume. Characterization of the influence of these admixtures on hydration was completed using x-ray diffraction, isothermal calorimetry, and chemical shrinkage. Investigations on the implications of early-age volume change were conducted for autogenous deformation. In addition to laboratory testing, the final phase of the project was to correlate and elucidate the data generated in the laboratory to real-world field performance. Field trials were conducted to evaluate and monitor the behavior of CAC systems and investigate the link between laboratory generated research and actual large scale behavior. / text