Diploma thesis is focused on manufacturing process of waveguide filter. Thesis is divided to 8 chapters. There is summarized theory of possible execution of waveguide filter, used materials, their influence and risks during production. Then are described possible steps of realization and necessary relations for its design, simulation and also practical realization. At conclusion are summarized, compared and described reached results.

In this master work, we investigated the feasibility of a magnetic resonance measurement technique using magnetic nanoparticle dispersions in both liquid and solid form. The implementation is realised as a coplanar waveguide operating in the frequency range of 0.5 - 20 GHz and an electromagnet producing a static magnetic field of strength up to 1.2 T. The Gilbert magnetic damping factor is determined for polymer composites of magnetic nanoparticles and the gyromagnetic ratio is determined for both nanoparticle dispersions in liquid form and polymer composites.

The main objectives of this research are to investigate and design low profile antennas for mobile handsets applications using the balanced concept. These antennas are considered to cover a wide range of wireless standards such as: DCS (1710¿1880 MHz), PCS (1850¿1990 MHz), UMTS (1920¿2170 MHz), WLAN (2400¿2500 MHz and 5000 ¿ 5800 MHz) and UWB frequency bands. Various antennas are implemented based on built-in planar dipole with a folded arm structure. The performance of several designed antennas in terms of input return loss, radiation patterns, radiation efficiency and power gain are presented and several remarkable results are obtained. The measurements confirm the theoretical design concept and show reasonable agreement with computations. The stability performance of the proposed antenna is also evaluated by analysing the current distribution on the mobile phone ground plane. The specific absorption rate (SAR) performance of the antenna is also studied experimentally by measuring antenna near field exposure. The measurement results are correlated with the calculated ones. A new dual-band balanced antenna using coplanar waveguide structure is also proposed, discussed and tested; this is intended to eliminate the balanced feed network. The predicted and measured results show good agreement, confirming good impedance bandwidth characteristics and excellent dual-band performance. In addition, a hybrid method to model the human body interaction with a dual band balanced antenna structure covering the 2.4 GHz and 5.2 GHz bands is presented. Results for several test cases of antenna locations on the body are presented and discussed. The near and far fields were incorporated to provide a full understanding of the impact on human tissue. The cumulative distribution function of the radiation efficiency and absorbed power are also evaluated. / UK Engineering and Physical Sciences Research Council (EPSRC)

No description available.

This project investigates developing and implementing innovative indoornavigation systems by leveraging repurposed Wi-Fi infrastructure anddedicated RFM69HCW transceivers. Aimed at enhancing indoor positioningaccuracy, the study explores the viability of using Received Signal StrengthIndicator (RSSI) and dedicated device localization techniques to overcomethe limitations of existing Global Positioning System (GPS) technology inindoor environments. Through the design and testing of a printed circuit board(PCB) prototype that connects Raspberry Pi Pico (RPP) to RFM69HCWmodules and the development of custom drivers for the RP2040 processor,this research addresses the challenges of indoor navigation, such as signalvariability and environmental interference. The project also emphasizes theimportance of sustainable technology development by repurposing electronicwaste for innovative applications. Findings from the study reveal the potentialof these methodologies to improve indoor positioning accuracy despitechallenges related to hardware compatibility and the dynamic nature of indoorspaces. This research contributes to indoor navigation by demonstrating thefeasibility of using repurposed and dedicated hardware solutions, offeringinsights into future directions for enhancing indoor navigation systems, andhighlighting the role of sustainability in technological innovation.

The main objectives of this research are to investigate and design low profile antennas for mobile handsets applications using the balanced concept. These antennas are considered to cover a wide range of wireless standards such as: DCS (1710-1880 MHz), PCS (1850-1990 MHz), UMTS (1920-2170 MHz), WLAN (2400-2500 MHz and 5000-5800 MHz) and UWB frequency bands. Various antennas are implemented based on built-in planar dipole with a folded arm structure. The performance of several designed antennas in terms of input return loss, radiation patterns, radiation efficiency and power gain are presented and several remarkable results are obtained. The measurements confirm the theoretical design concept and show reasonable agreement with computations. The stability performance of the proposed antenna is also evaluated by analysing the current distribution on the mobile phone ground plane. The specific absorption rate (SAR) performance of the antenna is also studied experimentally by measuring antenna near field exposure. The measurement results are correlated with the calculated ones. A new dual-band balanced antenna using coplanar waveguide structure is also proposed, discussed and tested; this is intended to eliminate the balanced feed network. The predicted and measured results show good agreement, confirming good impedance bandwidth characteristics and excellent dual-band performance. In addition, a hybrid method to model the human body interaction with a dual band balanced antenna structure covering the 2.4 GHz and 5.2 GHz bands is presented. Results for several test cases of antenna locations on the body are presented and discussed. The near and far fields were incorporated to provide a full understanding of the impact on human tissue. The cumulative distribution function of the radiation efficiency and absorbed power are also evaluated.

EDELWEISS est une expérience de détection directe de matière noire froide non-baryonique sous forme de particules massives et faiblement interagissantes (connues sous l'acronyme de WIMPs), qui constituent actuellement les candidats les plus populaires pour rendre compte de la masse manquante de l'Univers. Dans ce but, EDELWEISS utilise des bolomètres de germanium opérés à température cryogénique (20 mK environ) dans le Laboratoire Souterrain de Modane (LSM) à la frontière franco-italienne. En particulier, depuis 2008, un nouveau type de détecteur est en fonctionnement, équipé d'électrodes concentriques pour optimiser le rejet des évènements de surface (détecteurs à grilles coplanaires). Cette thèse se décompose en plusieurs axes de recherche. Tout d'abord, nous avons réalisé des mesures concernant la collecte des charges dans les cristaux. Les lois de vitesse des porteurs (électrons et trous) ont été déterminées dans le germanium à 20 mK dans la direction <100>, et une étude complète de la répartition des charges a été menée, avec une évaluation de l'anisotropie du transport et de la diffusion transverse des porteurs. Ces résultats permettent d'avoir une meilleure compréhension du fonctionnement interne des détecteurs d'Edelweiss. Ensuite, des études portant sur l'amélioration des performances ont été effectuées. Nous avons en particulier permis d'optimiser la procédure de régénération des cristaux et améliorer le rejet passif des évènements de surface (β). Le volume utile de détection des détecteurs a été évalué en utilisant les raies de deux radio-isotopes activés cosmiquement, le 68Ge et le 65Zn. Enfin, une étude exhaustive portant sur l'étude des spectres à basse énergie a été menée, ce qui permet de mettre au point une méthode d'analyse systématique pour la recherche de WIMPs de basse masse dans EDELWEISS. / EDELWEISS is a direct non-baryonic cold dark matter detection experiment in the form of weakly interacting massive particles (also known as WIMPs), which currently constitute the most popular candidates to account for the missing mass in the Universe. To this purpose, EDELWEISS uses germanium bolometers at cryogenic temperature (20 mK approximately) in the Underground Laboratory of Modane (LSM) at the French-Italian border. Since 2008, a new type of detector is operated, equipped with concentric electrodes to optimize the rejection of surface events (coplanar-grid detectors). This thesis work is divided into several research orientations. First, we carried out measurements concerning charge collection in the crystals. The velocity laws of the carriers (electrons and holes) have been determined in germanium at 20 mK in the <100> orientation, and a complete study of charge sharing has been done, including an evaluation of the transport anisotropy and of the straggling of the carriers. These results lead to a better understanding of the inner properties of the EDELWEISS detectors. Then, studies relating to the improvement of the performances were carried out. In particular, we have optimized the space-charge cancellation procedure in the crystals and improved the passive rejection of surface events (β). The fiducial volume of the detectors has been evaluated using two X-ray lines from cosmically activated radionuclides: 68Ge and 65Zn. Lastly, an exhaustive study of the low energy spectra has been carried out, which makes it possible to develop a systematic analysis method for the search of low-mass WIMPs in EDELWEISS.

Ultra Wideband (UWB) communication has recently drawn considerable attention from academia and industry. This is mainly owing to the ultra high speeds and cognitive features it could offer. The employability of UWB in numerous areas including but not limited to Wireless Personal Area Networks, WPAN's, Body Area Networks, BAN's, radar and medical imaging etc. has opened several avenues of research and development. However, still there is a disagreement on the standardization of UWB. Two contesting radios for UWB are Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) and DS-UWB (Direct Sequence Ultra Wideband). As nearly all of the reported research on UWB hasbeen about a very narrow/specific area of the communication system, this thesis looks at the end-to-end performance of an MB-OFDM approach. The overall aim of this project has been to first focus on three different aspects i.e. interference, antenna and propagation aspects of an MB-OFDM system individually and then present a holistic or an end-to-end system analysis finally. In the first phase of the project the author investigated the performance of MB-OFDM system under the effect of his proposed generic or technology non-specific interference. Avoiding the conventional Gaussian approximation, the author has employed an advanced stochastic method. A total of two approaches have been presented in this phase of the project. The first approach is an indirect one which involves the Moment Generating Functions (MGF's) of the Signal-to-Interference-plus-Noise-Ratio (SINR) and the Probability Density Function (pdf) of the SINR to calculate the Average Probabilities of Error of an MB-OFDM system under the influence of proposed generic interference. This approach assumed a specific two-dimensional Poisson spatial/geometric placement of interferers around the victim MB-OFDM receiver. The second approach is a direct approach and extends the first approach by employing a wider class of generic interference. In the second phase of the work the author designed, simulated, prototyped and tested novel compact monopole planar antennas for UWB application. In this phase of the research, compact antennas for the UWB application are presented. These designs employ low-loss Rogers duroid substrates and are fed by Copla-nar Waveguides. The antennas have a proposed feed-line to the main radiating element transition region. This transition region is formed by a special step-generating function-set called the "Inverse Parabolic Step Sequence" or IPSS. These IPSS-based antennas are simulated, prototyped and then tested in the ane-choic chamber. An empirical approach, aimed to further miniaturize IPSS-based antennas, was also derived in this phase of the project. The empirical approach has been applied to derive the design of a further miniaturized antenna. More-over, an electrical miniaturization limit has been concluded for the IPSS-based antennas. The third phase of the project has investigated the effect of the indoor furnishing on the distribution of the elevation Angle-of-Arrival (AOA) of the rays at the receiver. Previously, constant distributions for the AOA of the rays in the elevation direction had been reported. This phase of the research has proposed that the AOA distribution is not fixed. It is established by the author that the indoor elevation AOA distributions depend on the discrete levels of furnishing. A joint time-angle-furnishing channel model is presented in this research phase. In addition, this phase of the thesis proposes two vectorial or any direction AOA distributions for the UWB indoor environments. Finally, the last phase of this thesis is presented. As stated earlier, the overall aim of the project has been to look at three individual aspects of an MB-OFDM system, initially, and then look at the holistic system, finally. Therefore, this final phase of the research presents an end-to-end MB-OFDM system analysis. The interference analysis of the first phase of the project is revisited to re-calculate the probability of bit error with realistic/measured path loss exponents which have been reported in the existing literature. In this method, Gaussian Quadrature Rule based approximations are computed for the average probability of bit error. Last but not the least, an end-to-end or comprehensive system equation/impulse response is presented. The proposed system equation covers more aspects of an indoor UWB system than reported in the existing literature.

This work deals with the most famous constructions of planar antennas. The work analyses selected methods of connecting planar antennas' charging with the possibility of impedance adaptation. An important part of the work consists of description of techniques for increasing bandwidth and conversely techniques for reducing the dimensions which are important for the design of planar antennas for mobile devices. The antennas were designed by means of theoretical basis and their properties were examined in the electromagnetic field simulator. The selected antenna model was constructed and its parameters were measured experimentally. The matching circuit for the antenna to tune it to different resonant frequencies was designed and constructed.

A 5 GHz continuous unlicensed bandwidth is available at millimeter-wave (mm-wave) frequencies around 60 GHz and offers the prospect for multi gigabit wireless applications. The inherent atmospheric attenuation at 60 GHz due to oxygen absorption makes the frequency range ideal for short distance communication networks. For these mm-wave wireless networks, the low noise amplifier (LNA) is a critical subsystem determining the receiver performance i.e., the noise figure (NF) and receiver sensitivity. It however proves challenging to realise high performance mm-wave LNAs in a silicon (Si) complementary metal-oxide semiconductor (CMOS) technology. The mm-wave passive devices, specifically on-chip inductors, experience high propagation loss due to the conductivity of the Si substrate at mm-wave frequencies, degrading the performance of the LNA and subsequently the performance of the receiver architecture. The research is aimed at realising a high performance mm-wave LNA in a Si BiCMOS technology. The focal points are firstly, the fundamental understanding of the various forms of losses passive inductors experience and the techniques to address these issues, and secondly, whether the performance of mm-wave passive inductors can be improved by means of geometry optimising. An associated hypothesis is formulated, where the research outcome results in a preferred passive inductor and formulates an optimised passive inductor for mm-wave applications. The performance of the mm-wave inductor is evaluated using the quality factor (Q-factor) as a figure of merit. An increased inductor Q-factor translates to improved LNA input and output matching performance and contributes to the lowering of the LNA NF. The passive inductors are designed and simulated in a 2.5D electromagnetic (EM) simulator. The electrical characteristics of the passive structures are exported to a SPICE netlist which is included in a circuit simulator to evaluate and investigate the LNA performance. Two LNAs are designed and prototyped using the 13μ-m SiGe BiCMOS process from IBM as part of the experimental process to validate the hypothesis. One LNA implements the preferred inductor structures as a benchmark, while the second LNA, identical to the first, replaces one inductor with the optimised inductor. Experimental verification allows complete characterization of the passive inductors and the performance of the LNAs to prove the hypothesis. According to the author's knowledge, the slow-wave coplanar waveguide (S-CPW) achieves a higher Q-factor than microstrip and coplanar waveguide (CPW) transmission lines at mm-wave frequencies implemented for the 130 nm SiGe BiCMOS technology node. In literature, specific S-CPW transmission line geometry parameters have previously been investigated, but this work optimises the signal-to-ground spacing of the S-CPW transmission lines without changing the characteristic impedance of the lines. Optimising the S-CPW transmission line for 60 GHz increases the Q-factor from 38 to 50 in simulation, a 32 % improvement, and from 8 to 10 in measurements. Furthermore, replacing only one inductor in the output matching network of the LNA with the higher Q-factor inductor, improves the input and output matching performance of the LNA, resulting in a 5 dB input and output reflection coefficient improvement. Although a 5 dB improvement in matching performance is obtained, the resultant noise and gain performance show no significant improvement. The single stage LNAs achieve a simulated gain and NF of 13 dB and 5.3 dB respectively, and dissipate 6 mW from the 1.5 V supply. The LNA focused to attain high gain and a low NF, trading off linearity and as a result obtained poor 1 dB compression of -21.7 dBm. The LNA results are not state of the art but are comparable to SiGe BiCMOS LNAs presented in literature, achieving similar gain, NF and power dissipation figures. / Dissertation (MEng)--University of Pretoria, 2012. / Electrical, Electronic and Computer Engineering / unrestricted