The designs of various feeding networks for microstrip antennas have been investigated in this dissertation. In the active microstrip antenna designs, an amplifier-type microstrip antenna integrates a two- port amplifier circuitry to the various passive antennas through a 50£[ inset microstrip feed line which can function in broadband operation¡ACP operation and dual-frequency operation. As for the broadband circularly polarized microstrip antenna with a dual-perpendicular feed design, antenna with a dual-perpendicular feed which was formed by a Wilkinson power divider with a quarter-wavelength section of microstrip line for providing equal splitting of the input power and 90¢X phase difference to the two feed points has been presented. The broadband CP bandwidth can be achieved due to the good isolation between the two output lines of the feed network. In the microstrip antennas with CPW feed designs, we first proposed a microstrip antenna with three-dimensional CPW feed. A separate feed substrate is used which can provide a large-area space for the layout of complicated microwave circuitry. In addition, the feed substrate can also be oriented to the patch substrate with various angles, resulting in more flexibility in the proposed three-dimensional feed design. Finally, we proposed a design with two slot lines located at both sides of the coupling slot which can lengthen the excited patch surface current path, thus the resonant frequency is reduced and an antenna size reduction up to 40% has been obtained.

This thesis presents the rectifying antenna potential for infrared and millimeter wave energy conversion. Infrared imaging is one of the emerging technologies that have attracted considerable attention in the next generation of military, medical, and commercial applications. Moreover, with the ever-increasing congestion of the electromagnetic spectrum at RF and microwave frequencies and the establishment of firm civilian and military requirements best met by millimeter wave systems, the interest in the technology has grown and is now firmly established. During this work a 2.5GHz slot antenna, a 2.5GHz Schottky diode detector, a CPW-to-Microstrip transition, a fully integrated Rectenna element, and a 94GHz slot antenna were designed, fabricated, and tested. Results on the performance of the devices show a great deal of correlation between the simulated and measured data. To perform an initial study, the CPW-fed narrow slot antenna is designed at 2.5GHz and implemented on an FR-4 board. This investigation serves as the basis for the development of the Rectenna element at millimeter wave frequencies. In order to increase the bandwidth of the slot antenna, a 2.5GHz CPW-fed wide slot antenna with U-shaped tuning stub is realized, which provides a 60% increase in bandwidth while keeping the same radiation characteristics. In addition, a set of simulations is performed to show how a reflector plate affects the radiating properties of the slot antenna. A 2.5GHz square-law detector is also designed, fabricated, and tested in order to rectify the RF signal delivered by the antenna. The fabricated detector presents a well matched condition at the design frequency with a dynamic range found to be from --17dBm to --50dBm. The low frequency Rectenna element prototype is then integrated within a single FR-4 board. This is accomplished by implementing a compact via-less CPW-to-Microstrip transition. Finally, a 94GHz CPW-fed wide slot antenna is realized on a 10μm high resistivity silicon membrane. This antenna shows a great deal of similarity to the 2.5GHz slot antenna. This low profile antenna presents at least a 10dB return loss over the entire W band frequency window. Simulated antenna efficiencies of up to 99% were achieved assuming a perfect conductor.

Thesis (MSc (Applied Mathematics))--University of Stellenbosch, 2010. / ENGLISH ABSTRACT: This thesis provides an introduction to the statistical modeling technique known as graphical models. Since graph theory and probability theory are the two legs of graphical models, these two topics are presented, and then combined to produce two examples of graphical models: Bayesian Networks and Markov Random Fields. Furthermore, the max-sum, sum-product and junction tree algorithms are discussed. The graphical modeling technique is then applied to the specific problem of finding coplanar points in stereo images, taken with an uncalibrated camera. Although it is discovered that graphical models might not be the best method, in terms of speed, to use for this appliation, it does illustrate how to apply this technique in a real-life problem. / AFRIKAANSE OPSOMMING: Hierdie tesis stel die leser voor aan die statistiese modelerings-tegniek genoemd grafiese modelle. Aangesien grafiek teorie en waarskynlikheidsleer die twee bene van grafiese modelle is, word hierdie areas aangespreek en dan gekombineer om twee voorbeelde van grafiese modelle te vind: Bayesian Netwerke en Markov Lukrake Liggaam. Die maks-som, som-produk en aansluitboom algoritmes word ook bestudeer. Nadat die teorie van grafiese modelle en hierdie drie algoritmes afgehandel is, word grafiese modelle dan toegepas op ’n spesifieke probleem— om punte op ’n gemeenskaplike vlak in stereo beelde te vind, wat met ’n ongekalibreerde kamera geneem is. Alhoewel gevind is dat grafiese modelle nie die optimale metode is om punte op ’n gemeenskaplike vlak te vind, in terme van spoed, word die gebruik van grafiese modelle wel ten toongestel met hierdie praktiese voorbeeld. / National Research Foundation (South Africa)

Orientador: Luiz Carlos Kretly / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Eletrica e de Computação / Made available in DSpace on 2018-08-13T08:18:49Z (GMT). No. of bitstreams: 1 Atanazio_PauloFilipeBraghetto_M.pdf: 6727187 bytes, checksum: 90bbbbf904ffcce6757eeaeefe4abd96 (MD5) Previous issue date: 2009 / Resumo: O propósito deste trabalho é, a partir dos conceitos de linhas de transmissão, teoria de filtros e o conhecimento pioneiro deste grupo acerca das chaves MEMS de RF, propor duas aplicações reais baseadas nesta estrutura singular: um deslocador de fase e um filtro sintonizável na faixa de 0,1-35GHz e banda Ku (12,4-18GHz) respectivamente. Uma abordagem puramente eletromecânica é realizada na etapa inicial, observando a tensão de ativação da chave para diferentes formas estruturais, desmistificando a histerese mecânica, fenômeno intrínseco a este tipo de dispositivo. Na segunda fase do trabalho é feito um detalhamento do comportamento eletromagnético da chave MEMS, explorando fortemente a extração dos parâmetros elétricos e sua inserção em outros circuitos. Por fim, a implementação do filtro sintonizável e do deslocador de fase realizouse baseada nos conceitos de DMTL - Distributed MEMS Trasmission Lines - onde tanto a seleção da frequência central de passagem do filtro, quanto o comprimento elétrico total do deslocador são controladas pela capacitância variável da chave MEMS, de acordo com uma tensão de controle DC aplicada. / Abstract: The purpose of this work is, based on transmission line concepts, filter theory and the pioneer knowledge of this group about RF MEMS Switches, propose two physical applications employing this singular structure: a phase shifter and a tunable filter at 0.1 - 35GHz range and Ku band respectively. A purely electromechanical approach is done at the initial step, observing the switch pull-in voltages for several structural geometries, demystifying the mechanical hysteresis, intrinsic phenomena of this kind of device. On the second phase of the work, the MEMS switch electromagnetic behavior is detailed, strongly exploring the electrical parameters extraction and its application on other types of circuits. Finally, the tunable filter and phase shifter are implemented through DMTL - Distributed MEMS Transmission Lines - concepts, where frequency selection and the amount of phase shifting are controlled by the variable switch capacitance according to the applied DC control voltage. / Mestrado / Telecomunicações e Telemática / Mestre em Engenharia Elétrica

No description available.

Diploma thesis is focused to design of a system with circularly polarized wave for frequency band 2.4 GHz. The thesis introduces question of the microwave antennas, matching circuits and circular polarization circuit. It also includes a design of a circuit for available chip antenna (2450AT45A100) measurement and its measuring with connected chip antenna. Design and measurement of a circular polarization circuit using available chip antennas are also included in this thesis.

This thesis deals with the design of omnidirectional monopole antennas. Using the parabolic reflector and the directors, the directional characteristics of monopole antennas are modified. This directional antenna, together with the omnidirectional antenna, examines the effect of various materials, the emission characteristics and the input reflection factor, near the antennas. These antennas are made of 3D textile, measured in anechoic chamber and compared to the designed antennas. At the end of the thesis is the summary and evaluation of the result.

No description available.

No description available.

Nous proposons dans cette thèse de nouvelles structures à faibles pertes en vue de leur utilisation dans les bandes millimétriques. L'hypothèse forte sur laquelle es t construite notre étude est que la présence du silicium permet d'envisager une intégration plus facile des circuits. Pour ce faire nous avons étudié les caractéristiques électriques des lignes inversées silicium-verre à 60 GHz ainsi que la ligne de Goubau sur silicium aux mêmes fréquences. Nous nous sommes focalisés sur l'étude des pertes des lignes. Les simulations présentées jusqu'à 60 GHz ont montré que les qualités de la technologie verre-silicium sont bonnes en termes de paramètres hyperfréquences. Nous proposons donc d'utiliser plutôt le verre pour la partie passive et le silicium pour la partie active. Nous montrons ainsi que cette technologie admet la réalisation des fonctions diverses et qu'elle est susceptible de permettre l'obtention de systèmes intégrés / We propose in this thesis several new structures with low loss for use in millimeter bands. The strong supposition with which is built our study is : the presence of silicon can be considered easier integration of circuits. That the reason why we have been studied the electrical characteristics of glass-silicon lines inverted at 60 GHz and the Goubau line on silicon with the same frequencies. We focus our attention on these studies of losses in lines. The simulations up to 60 GHz showed the qualities of the glass-silicon technology are good in terms of microwave parameters. So we propose to use glass for the passive and silicon for the active part. And we show that this technology allows the realization of various functions and is likely to allow the acquisition of integrated systems