In order to investigate the two-phase flow behaviour in a complex reactor-typical geometry and to supply suitable data for CFD code validation, a model of the hot leg of a pressurised water reactor was built at FZD. The hot leg model is operated in the pressure chamber of the TOPFLOW test facility, which is used to perform high-pressure experiments under pressure equilibrium with the inside atmosphere of the chamber. This technique makes it possible to visualise the two-phase flow through large windows, also at reactor-typical pressure levels. In order to optimise the optical observation possibilities, the test section was designed with a rectangular cross-section. Experiments were performed with air and water at 1.5 and 3.0 bar at room temperature as well as with steam and water at 15, 30 and 50 bar and the corresponding saturation temperature (i.e. up to 264°C). The total of 194 runs are divided into 4 types of experiments covering stationary co-current flow, counter-current flow, flow without water circulation and transient counter-current flow limitation (CCFL) experiments. This report provides a detailed documentation of the experiments including information on the experimental setup, experimental procedure, test matrix and on the calibration of the measuring devices. The available data is described and data sheets were arranged for each experiment in order to give an overview of the most important parameters. For the cocurrent flow experiments, water level histograms were arranged and used to characterise the flow in the hot leg. In fact, the form of the probability distribution was found to be sensitive to the boundary conditions and, therefore, is useful for the CFD comparison. Furthermore, the flooding characteristics of the hot leg model plotted in terms of the classical Wallis parameter or Kutateladze number were found to fail to properly correlate the data of the air/water and steam/water series. Therefore, a modified Wallis parameter is proposed, which takes the effect of viscosity into account.

In order to investigate the two-phase flow behaviour in a complex reactor-typical geometry and to supply suitable data for CFD code validation, a model of the hot leg of a pressurised water reactor was built at FZD. The hot leg model is operated in the pressure chamber of the TOPFLOW test facility, which is used to perform high-pressure experiments under pressure equilibrium with the inside atmosphere of the chamber. This technique makes it possible to visualise the two-phase flow through large windows, also at reactor-typical pressure levels. In order to optimise the optical observation possibilities, the test section was designed with a rectangular cross-section. Experiments were performed with air and water at 1.5 and 3.0 bar at room temperature as well as with steam and water at 15, 30 and 50 bar and the corresponding saturation temperature (i.e. up to 264°C). The total of 194 runs are divided into 4 types of experiments covering stationary co-current flow, counter-current flow, flow without water circulation and transient counter-current flow limitation (CCFL) experiments. This report provides a detailed documentation of the experiments including information on the experimental setup, experimental procedure, test matrix and on the calibration of the measuring devices. The available data is described and data sheets were arranged for each experiment in order to give an overview of the most important parameters. For the cocurrent flow experiments, water level histograms were arranged and used to characterise the flow in the hot leg. In fact, the form of the probability distribution was found to be sensitive to the boundary conditions and, therefore, is useful for the CFD comparison. Furthermore, the flooding characteristics of the hot leg model plotted in terms of the classical Wallis parameter or Kutateladze number were found to fail to properly correlate the data of the air/water and steam/water series. Therefore, a modified Wallis parameter is proposed, which takes the effect of viscosity into account.

Counter-Current Flow Limitation (CCFL) is of importance for PWR safety analyses in several accident scenarios connected with loss of coolant. Basing on the experiences obtained during a first series of hot leg tests now new experiments on counter-current flow limitation were conducted in the TOPFLOW pressure vessel. The test series comprises air-water tests at 1 and 2 bar as well as steam-water tests at 10, 25 and 50 bar. During the experiments the flow structure was observed along the hot leg model using a high-speed camera and web-cams. In addition pressure was measured at several positions along the horizontal part and the water levels in the reactor-simulator and steam-generator-simulator tanks were determined. This report documents the experimental setup including the description of operational and special measuring techniques, the experimental procedure and the data obtained. From these data flooding curves were obtained basing on the Wallis parameter. The results show a slight shift of the curves in dependency of the pressure. In addition a slight decrease of the slope was found with increasing pressure. Additional investigations concern the effects of hysteresis and the frequencies of liquid slugs. The latter ones show a dependency on pressure and the mass flow rate of the injected water. The data are available for CFD-model development and validation.

Stratified two-phase flows were investigated at different test facilities with horizontal test sections in order to provide an experimental database for the development and validation of computational fluid dynamics (CFD) codes. These channels were designed with rectangular cross-sections to enable optimal observation conditions for the application of optical measurement techniques. Consequently, the local flow structure was visualised with a high-speed video camera, delivering data with high-resolution in space and time as needed for CFD code validation. Generic investigations were performed at atmospheric pressure and room temperature in two air/water channels made of acrylic glass. Divers preliminary experiments were conducted with various measuring systems in a test section mounted between two separators. The second test facility, the Horizontal Air/Water Channel (HAWAC), is dedicated to co-current flow investigations. The hydraulic jump as the quasi-stationary discontinuous transition between super- and subcritical flow was studied in this closed channel. Moreover, the instable wave growth leading to slug flow was investigated from the test section inlet. For quantitative analysis of the optical measurements, an algorithm was developed to recognise the stratified interface in the camera frames, allowing statistical treatments for comparison with CFD calculation results. The third test apparatus was installed in the pressure chamber of the TOPFLOW test facility in order to be operated at reactor typical conditions under pressure equilibrium with the vessel atmosphere. The test section representing a flat model of the hot leg of the German Konvoi pressurised water reactor (PWR) scaled at 1:3 is equipped with large glass side walls in the region of the elbow and of the steam generator inlet chamber to allow visual observations. The experiments were conducted with air and water at room temperature and maximum pressures of 3 bar as well as with steam and water at boundary conditions of up to 50 bar and 264°C. Four types of experiments were performed, including generic test cases as well as transient validation cases of typical nuclear reactor safety issues. As an example, the co-current flow experiments simulate the two-phase natural circulation in the primary circuit of a PWR. The probability distribution of the water level measured in the reactor pressure vessel simulator was used to characterise the flow in the hot leg. Moreover, the flooding behaviour in this conduit was investigated with dedicated counter-current flow limitation experiments. A comparison of the flooding characteristics with similar experimental data and correlations available in the literature shows that the channel height is the characteristic length to be used in the Wallis parameter for channels with rectangular cross-sections. Furthermore, for the analysis of steam/water experiments, condensation effects had to be taken into account. Finally, the experimental results confirm that the Wallis similarity is appropriate to scale flooding in the hot leg of a PWR over a large range of pressure and temperature conditions. Not least, different examples of comparison between experiment and simulation demonstrate the possibilities offered by the data to support the development and validation of CFD codes. Besides the comparison of qualitative aspects, it is shown exemplarily how to treat the CFD results in order to enable quantitative comparisons with the experiments.

Purpose – The purpose of this study is to increase the knowledge about the material handling of a module house manufacturing company. In order to achieve the study's purpose, three research questions were formulated. ▪ Which factors affect material handling? ▪ Which factors are considered important for material handling? ▪ How can standardization improve material handling? Method – The study has been characterized by an inductive approach to conducting the case study. To achieve the purpose, empirical data has been collected via a pilot study, interviews, observations, and document studies from reality. Subsequently, previous theories were examined via a literature collection. Furthermore, the processing and analysis of collected empirics and theory have helped to answer the purpose and demonstrate the generalizability of the study. Findings – The study has focused on the entirety of the various processes and an understanding of the various factors that influence material handling has been obtained. The case study company has challenges to look at the entirety of the modular house production and separates the production and construction sites. The wastes transport, movement, waiting and unused skills are considered to be the most important wastes to reduce or eliminate. It is clear that the case study company’s new employees must constantly reinvent the wheel and learn from their own mistakes. Moreover, it is difficult to determine if the mistake is a deviation, error or insufficient knowledge. By implementing a standard for what should be on drawings and how materials are to be delivered from production to the construction sites, deviations and wastes can be reduced and costs reduced. Implications – The study is based on a problem area that already exists in separate theories and comparisons. However, operations that have a material handling that both concerns manufacturing and construction work have not previously been investigated to the same extent, which is the theoretical contribution of the study. The empirical contribution to the study is to identify which factors affect material handling in businesses that have common flows between manufacturing and construction work. Limitations – The study only addresses two of the material handling flows; the material flow and the information flow. The study also does not take into account the processes of suppliers, subcontractors, or customers. Finally, the study will not include financial calculations to demonstrate potential cost efficiencies. Keywords – Material handling, Lean, Construction logistics, Wastes, Current flow, Value stream mapping, Lean tools.

Submitted by SBI Biblioteca Digital (sbi.bibliotecadigital@puc-campinas.edu.br) on 2017-08-10T11:55:42Z No. of bitstreams: 1 FABIANA DA SILVA PODELESKI.pdf: 1801192 bytes, checksum: 27ac2ce1c17ed0cdfce39e602146bdc7 (MD5) / Made available in DSpace on 2017-08-10T11:55:42Z (GMT). No. of bitstreams: 1 FABIANA DA SILVA PODELESKI.pdf: 1801192 bytes, checksum: 27ac2ce1c17ed0cdfce39e602146bdc7 (MD5) Previous issue date: 2017-06-29 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior - CAPES / This document proposes a new approach for the restoration of electric power distribution systems by optimal current flow model (OCF). The importance of working with proposals for restoration using OCF is to allow analyzing the problem of restoration by a multiobjective mathematical programming model with linear or quadratic objective function and constraints that represent the network structure of the distribution system. Two objectives are evaluated for the restoration, losses reduction and recomposition time, resulting in a multiobjective programming problem. The proposed restoration action consists of opening and closing of branches in order to transfer loads to areas that are affected by interrupting the power supply. The proposition is directed to the primary distribution networks, characterized by presenting a radial topology and being in a restorative state, when there is a permanent fault. It is also suitable for systems with distributed generation (DG) when the power flow in the branches is no longer unidirectional. The resolution of the problem starts from the prior knowledge of the distribution system (topology and operational levels), the affected region and the possible recomposition resources for restoring the network through OCF model. The objective function of losses can be represented by a linear or a quadratic function. The linear representation results in a problem with linear equations and inequalities, that is, in a linear programming problem. The use of a quadratic objective function (minimization of losses) implies a more complex model for execution, since it results in a set of linear and non-linear equations and inequalities, when it is a multiobjective problem. The quadratic model may become unsuitable for applications in smart grid technologies due to longer algorithm execution time. The results attested the importance of applying a multiobjective proposal, because when individually evaluated the criteria of loss minimization and shorter recomposition time, different recomposition options were obtained. / O presente documento prop?e um novo enfoque para a recomposi??o de sistemas de distribui??o de energia el?trica resolvido por modelo de Fluxo de Corrente ?timo (FCO). A import?ncia de se trabalhar com propostas para recomposi??o utilizando FCO ? possibilitar a an?lise do problema de recomposi??o por um modelo de programa??o matem?tica multiobjetivo, com fun??o objetivo linear ou quadr?tica e restri??es que representem a estrutura da rede do sistema de distribui??o. S?o avaliados dois objetivos para a recomposi??o, minimiza??o de perdas e menor tempo de recomposi??o, resultando em um problema de programa??o multiobjetivo. A a??o de recomposi??o proposta compreende manobras para transfer?ncia de carga ?s ?reas que se encontram ilhadas devido ? interrup??o de fornecimento de energia. A proposi??o est? dirigida ?s redes prim?rias de distribui??o, caracterizadas por apresentarem topologia radial e se encontrarem em um estado restaurativo, quando h? presen?a de uma falha permanente. Tamb?m ? adequada a sistemas com gera??o distribu?da (GD) quando os fluxos nos ramos deixam de ser unidirecionais. A resolu??o do problema parte do conhecimento pr?vio do sistema de distribui??o (topologia e n?veis operacionais), da regi?o afetada e dos poss?veis recursos restauradores para restaura??o da rede por meio de FCO. A fun??o objetivo pode ser representada por uma fun??o linear ou quadr?tica para as perdas. A representa??o linear resulta em um problema com equa??es e inequa??es lineares, ou seja, em um problema de programa??o linear. A utiliza??o de uma fun??o objetivo quadr?tica (minimiza??o de perdas) implica em um modelo mais complexo para execu??o, uma vez que re?ne um conjunto de equa??es e inequa??es lineares e n?o lineares, quando se tratar de um problema multiobjetivo. O modelo quadr?tico pode se tornar impr?prio para aplica??es em tecnologias de redes inteligentes devido ao maior tempo de execu??o de algoritmo. Os resultados atestaram a import?ncia de aplica??o de uma proposta multiobjetivo, pois quando avaliados individualmente os crit?rios de minimiza??o de perdas e de menor tempo de recomposi??o, foram obtidas diferentes op??es de recomposi??o.

Stratified two-phase flows were investigated at different test facilities with horizontal test sections in order to provide an experimental database for the development and validation of computational fluid dynamics (CFD) codes. These channels were designed with rectangular cross-sections to enable optimal observation conditions for the application of optical measurement techniques. Consequently, the local flow structure was visualised with a high-speed video camera, delivering data with high-resolution in space and time as needed for CFD code validation. Generic investigations were performed at atmospheric pressure and room temperature in two air/water channels made of acrylic glass. Divers preliminary experiments were conducted with various measuring systems in a test section mounted between two separators. The second test facility, the Horizontal Air/Water Channel (HAWAC), is dedicated to co-current flow investigations. The hydraulic jump as the quasi-stationary discontinuous transition between super- and subcritical flow was studied in this closed channel. Moreover, the instable wave growth leading to slug flow was investigated from the test section inlet. For quantitative analysis of the optical measurements, an algorithm was developed to recognise the stratified interface in the camera frames, allowing statistical treatments for comparison with CFD calculation results. The third test apparatus was installed in the pressure chamber of the TOPFLOW test facility in order to be operated at reactor typical conditions under pressure equilibrium with the vessel atmosphere. The test section representing a flat model of the hot leg of the German Konvoi pressurised water reactor (PWR) scaled at 1:3 is equipped with large glass side walls in the region of the elbow and of the steam generator inlet chamber to allow visual observations. The experiments were conducted with air and water at room temperature and maximum pressures of 3 bar as well as with steam and water at boundary conditions of up to 50 bar and 264°C. Four types of experiments were performed, including generic test cases as well as transient validation cases of typical nuclear reactor safety issues. As an example, the co-current flow experiments simulate the two-phase natural circulation in the primary circuit of a PWR. The probability distribution of the water level measured in the reactor pressure vessel simulator was used to characterise the flow in the hot leg. Moreover, the flooding behaviour in this conduit was investigated with dedicated counter-current flow limitation experiments. A comparison of the flooding characteristics with similar experimental data and correlations available in the literature shows that the channel height is the characteristic length to be used in the Wallis parameter for channels with rectangular cross-sections. Furthermore, for the analysis of steam/water experiments, condensation effects had to be taken into account. Finally, the experimental results confirm that the Wallis similarity is appropriate to scale flooding in the hot leg of a PWR over a large range of pressure and temperature conditions. Not least, different examples of comparison between experiment and simulation demonstrate the possibilities offered by the data to support the development and validation of CFD codes. Besides the comparison of qualitative aspects, it is shown exemplarily how to treat the CFD results in order to enable quantitative comparisons with the experiments.

Nanopore technology has introduced new techniques for single particle detection and analysis. A nanopore consists of a small opening in a membrane on the nanometer scale. Nanopores are found in nature and are utilized for transporting molecules through biological membranes. Researchers have been able to mimic naturally forming biological nanopores and utilize them for a variety of sensing applications. Nanopores, fabricated either organically or inorganically, can be used for detecting biomarkers such as proteins, nucleic acids, and metabolites that translocate the membrane by way of the nanopore. Constant ionic current flow is measured through the nanopore by way of a sensitive ammeter. In the presence of a biomarker, the ionic current flow will be impeded, causing the electrical signal to drop. This drop uniquely corresponds to the type of particle passing through the nanopore. In this work, the thin membrane on which the nanopore resides is created through a newly developed meniscus shaped sacrificial technique. The sacrificial polymer material starts as a liquid and is confined to the microfluidic channel through the capillary effect, giving it the meniscus profile. It is used as a structural support on which a thin silicon dioxide layer is grown. The layer of oxide takes on the same natural meniscus shape as the sacrificial material. The polymer is subsequently etched, resulting in a hollow core liquid channel with a suspended meniscus membrane. This process allows a thin membrane to be fabricated on top of a microfluidic channel that ranges from 50-200 nm in thickness. The meniscus membrane is crucial to the success of nanopore formation. The nanoscale membrane allows for smaller, more precise nanopores to be created. Reduced nanopore dimensions are advantageous for the detection of smaller biomarkers. The platform described in this dissertation integrates solid-state naturally forming meniscus membranes with solid-core and optofluidic waveguides for nanopore detection applications. The waveguides allow for a particle trap to be introduced to the system. The ability to trap particles directly under the nanopore is critical to the speed of which the nanopore can operate. This dissertation focuses on the fabrication, characterization, and testing of an optofluidic platform that features a nanopore for rapid single molecule detection and analysis.