Os aços inoxidáveis duplex (AIDs) são materiais com um excelente desempenho tanto mecânico como à corrosão. Inúmeras pesquisas tem sido desenvolvidas para aprimorar a soldabilidade destas ligas. Algumas transformações de fase, que são passíveis de ocorrer durante o processo de soldagem, podem prejudicar seriamente o desempenho das juntas. Foram simuladas microestruturas da região da zona afetada pelo calor submetida a temperaturas elevadas (ZACTE), utilizando um modelo proposto de fluxo de calor. Abordaram-se aspectos fundamentais da precipitação de austenita secundária, de nitreto de cromo e as suas interações na ZACTE de soldas multipasse. Finalmente, foram realizados testes de tenacidade e de resistência à corrosão para avaliar o efeito das transformações de fase estudadas no desempenho das juntas soldadas. Os tratamento térmicos e simulações da ZACTE foram realizadas num equipamento GleebleÒ. As microestruturas foram analisadas mediante microscopia ótica e eletrônica de varredura e de transmissão. Junto com a microscopia eletrônica foram realizadas microanálises químicas das fases estudadas. Baseando-se nos resultados obtidos, verificou-se que nem todos os AIDs são susceptíveis de ferritizar. Este fato tem uma grande influência no comportamento metalúrgico e na soldabilidade destes aços. Quanto aos aspectos fundamentais da metalurgia destes aços, observou-se uma estreita interação entre a precipitação da austenita secundária e os nitretos de cromo, chegando-se a propor um mecanismo de nucleação da austenita secundária intragranular a partir dos nitretos. Por último, foi constatado que o efeito deletério da austenita secundária intragranular na resistência à corrosão pode ser evitado mediante a adequada elaboração do procedimento de soldagem. / Duplex stainless steels (DSS) have excellent mechanical and corrosion properties. Many researches have been developed regarding the weldability of these alloys. There are some phase transformations that take place during the welding process, which may impair the welded joint behavior. High temperature heat-affected zone (HTHAZ) microstructures were simulated using a proposed heat flow model. Fundamental aspects of the secondary austenite and chromium nitride precipitation, and its interactions in the HTHAZ of multipass welds, were studied. In addition, toughness and corrosion tests were done to evaluate the influence of the studied phase transformations on the weld behavior. A GleebleÒ system was used to do the heat treatments and HTHAZ simulations. The microstructures were analyzed by means of optic and electron microscopy. Along with the electron microscopy it was done chemical microanalysis of the studied phases. Based on results, it was verified that not all DSSs can be ferritized. This fact has a strong influence on metallurgical behavior and weldability of these alloys. Regarding to the metallurgical fundamental aspects of these steels, it was observed a remarkable interaction between secondary austenite and chromium nitride precipitation. Thus, it was proposed a mechanism of intragranular secondary austenite precipitation from chromium nitrides. It was also verified, how the deleterious effect of intragranular secondary austenite in the corrosion resistance can be avoided by means of appropriate welding procedures.

Os aços inoxidáveis duplex são ligas Cr-Fe-Ni-Mo, que possuem uma microestrutura balanceada austenita-ferrita, e com excelentes propriedades mecânicas e de resistência à corrosão. Estas características os fazem muito utilizados nas industrias química, petroquímica, de papel, alimentícia e farmacêutica. O processamento destes aços geralmente envolve processos de soldagem, os quais devem ser elaborados cuidadosamente. Durante os ciclos térmicos experimentados na soldagem na zona afetada pelo calor, dependo do tempo de permanência no intervalo de temperaturas entre 650°C-950°C, podem ser precipitadas fases intermetálicas, como a fase sigma, que prejudicam as propriedades mecânicas e de resistência à corrosão. Três ligas comerciais de aços inoxidáveis duplex (AID) e superduplex (AISD) de denominação UNS S32304(AID), UNS S32750(AISD) e UNS S32760(AISD) foram submetidos a soldagem multipasse e a simulações de ciclos de soldagem na zona afetada pelo calor de temperatura baixa (ZACTB). As simulações foram realizadas em um dilatômetro e em um equipamento Gleeble®. Foram feitas comparações entre as microestruturas obtidas nas soldas reais e nos corpos-de-prova simulados. As microestruturas foram analisadas através de microscopia ótica e microscopia eletrônica de varredura. Foram também analisadas as fases precipitadas através de difração de Raios-X de resíduos extraídos, química e eletroliticamente, das amostras simuladas. Realizaram-se ensaios de corrosão intergranular e de polarização cíclica, para determinar o comportamento dos materiais à corrosão após a soldagem. Achou-se um bom acordo entre as microestruturas das soldas reais e as microestruturas simuladas. Encontrou-se que o aço UNS S32304 não precipitou nenhuma fase. No entanto, nos aços UNS S32750 e UNS S32760 foram encontradas fases precipitadas nos contornos de grão ferrítico. Essas fases foram identificadas como sigma e Cr2N. Entre estes dois últimos achou-se que o aço mais susceptível à precipitação de fases é o UNS S32760, provavelmente pela presença do W. Quanto ao comportamento à corrosão, não se observou nenhuma variação nos potenciais de pite após a simulação, enquanto que os potenciais de proteção sofreram uma queda comparando-se aos materiais na condição como-recebidos. / Duplex stainless steels are Cr-Fe-Ni-Mo alloys. They possess balanced austenitic/ ferritic microstructure, excellent mechanical and corrosion resistance properties. Thus, these characteristics make them very used in chemical, petrochemical, cellulose, food and pharmaceutical industries. The processing of these steels generally involves welding processes, which should be carried out carefully. Depending on time from 650°C to 950°C temperature range during thermal cycles in heat affected zone, intermetallic phases can be precipitated, as sigma phase for instance. As a consequence, mechanical and corrosion resistance might be impaired. Three duplex (DSS) and superduplex (SDSS) stainless steel alloys, with denomination of UNS S32304 (DSS), UNS S32750 (SDSS), and UNS S32760 (SDSS), were submitted to real multipass welding and welding thermal cycles simulations of low temperature heat affected zone. The simulations were accomplished in a dilatometer and in a Gleeble® equipment. They were made comparisons among microstructures obtained in actual welds and simulated welding thermal cycles. Microstructures were analyzed by optical and electronic microscopy. X-ray diffraction analyses of extracted residues were studied. Tests of intergranular corrosion and cyclic potentiodynamic polarization were performed. Results indicated good agreement between actual welding and thermal cycles simulated microstructures. UNS S32304 steel did not precipitate any intermetallic phase. On the other hand, in UNS S32750 and UNS S32760 steels were found precipitated phases in the ferritic grain boundary. Those phases were identified as sigma and Cr2N. UNS S32760 were more susceptible phase precipitation, probably due to tungsten as an additional alloying element in this steel. Corrosion results indicated no observed variation in pitting potentials of simulated samples, meanwhile pitting protection potentials suffered a fall compared to materials in the as received condition.

Os aços inoxidáveis duplex são materiais com um excelente desempenho, devido às suas sobressalentes propriedades mecânicas e excelente resistência à corrosão. Uma composição química adequada e microestrutura balanceada são as responsáveis por esta combinação de propriedades. No entanto, são estes mesmos fatores que os fazem especialmente susceptíveis à precipitação de fases intermetálicas, com efeitos maléficos no seu desempenho. Durante os ciclos térmicos de uma soldagem multipasse, a precipitação de intermetálicos é crítica. Foi desenvolvido um método para simular os ciclos térmicos de uma solda multipasse. Usando este método, foi estudada a precipitação de nitreto de cromo e fase sigma na zona afetada pelo calor submetida a temperaturas abaixo de 950°C dos aços inoxidáveis duplex UNS S31803 e S32550. Foram estudadas energias de soldagem na faixa de 0,4 a 1,0 kJ/mm. Foi determinada mediante extração de precipitados, seguida de difração de raios X na câmara de Debye-Scherrer e microscopia eletrônica de transmissão, a precipitação de nitreto de cromo para energias de soldagem de 0,4 a 1,0 kJ/mm e de fase sigma para energias de soldagem de 0,6-1,0 KJ/mm, no UNS S32550. Já o UNS S31803 não apresentou precipitação alguma para as energias de soldagem estudadas. Baseando-se nos resultados verifica-se que durante uma soldagem multipasse o UNS S31803 é menos propenso que o UNS S32550 à precipitação de intermetálicos na zona afetada pelo calor submetida a temperaturas abaixo de 950°C. / Duplex stainless steels belong to a group of high performance stainless steels regarding to corrosion and mechanical properties. These achievements are related to a suitable chemical composition and a balanced microstructure. During welding thermal cycles the microstructure changes and, consequently, corrosion and mechanical properties might be impaired due to a precipitation of intermetallic phases. This precipitation is an issue to be addressed for multipass welding. It was developed a method for simulate the multipass welding thermal cycles. Using this method chromium nitride and sigma phase precipitation was studied in a simulated heat affected zone of multipass welding (three passes) of UNS S31803 and UNS S32550 duplex stainless steels with different heat inputs (0,4 to 1,0 kJ/mm). The HAZ simulated region was below 950°C maximum temperature. Microstructural characterization of simulated samples showed discontinuous films of a precipitated phase at ferrite/ferrite grain boundaries and ferrite/austenite interfaces were observed only in a UNS S32550 duplex grade for all heat inputs simulated. This suggests that sigma phase and chromium nitride precipitation took place during sample thermocycling. X-ray diffraction in a Debye-Scherrer chamber of extracted precipitates and electron diffraction by TEM confirmed the presence of chromium nitrides for all range of heat input studied and sigma phase for heat input above 0,6 kJ/mm. On the other hand, microstructural analysis of UNS S31803 simulated samples did not present precipitation of intermetallic phases in the tested temperature range of HAZ. Based on these results, UNS S31803 is more resistant than UNS S32550 to intermetallic phases precipitation in multipass welding.

Abstract This thesis is devoted to studying two wireless relay network models, namely wireless tandem multiple-input-multiple-output (MIMO) relay networks and wireless two-hop multicast relay networks. Regarding wireless tandem MIMO relay networks, we develop a systematic approach to analyze their fundamental diversity-multiplexing tradeoff (DMT) under the assumption that the relays implement a class of practical full-duplex techniques that enable them to opt for either full-duplex or half-duplex mode. Based on the analysis, we make contribution from the following aspects: First of all, we thoroughly compare the performance of full-duplex and half-duplex mode operations in the framework of wireless tandem relay networks. We find that both full-duplex and half-duplex modes have opportunity to outperform each other. Specifically, for many tandem relay networks, in the low multiplexing gain region, the best relay-mode configuration is to let all the relays operate in half-duplex mode since this relay-mode configuration achieves the best diversity gain in the low multiplexing gain region. However, in the high multiplexing gain region, the best diversity gain is usually achieved by switching some relays to full-duplex mode. Furthermore, we study how residual interference at relays working in full-duplex mode affects the DMT of a tandem network. We find that residual interference not only derogates the performance of full-duplex mode, but also affects the optimal power allocation of the network. Specifically, if residual interference is zero or has a sufficiently low power level, a linear power allocation scheme can achieve the optimal DMT of the network. Otherwise, the optimal DMT is achieved by a nonlinear power allocation scheme. Finally, the DMT analysis illustrates an effective principle to deal with general multi-hop wireless networks, which is to break them down into small scale subnetworks with certain key structures. Then, studying the general multi-hop wireless networks essentially becomes studying those small scale subnetworks and the relationship among them. Regarding wireless two-hop multicast relay networks, we focus on a case study where a single source multicasts to two destinations through the assistance of two relays. We propose and analyze the performance of a partial decode-and-forward protocol for the network, which includes the full decode-and-forward protocol as a special case and achieves a better performance in general. Specifically, we prove that the achievable rate of the partial decode-and-forward protocol can either reach arbitrarily close to the cut-set upper bound of the network or reach within 1 bit/s/Hz to that, asymptotically with respect to the transmit power. We also show that the partial decode-and-forward protocol can achieve the optimal DMT of the network. Then, we discuss the perspective of implementing the partial decode-and-forward strategy to more general multicast relay networks. / Tiivistelmä Tämä opinnäytetyö tutkii kahta langatonta välitysverkkomallia, nimittäin langatonta tandem multiple-input-multiple-output (MIMO) välitysverkkoa ja langatonta monilähetysvälitysverkkoa kahdelle hypylle. Kehitämme systemaattisen lähestymistavan diversiteetti-multipleksointi vaihtokaupan (DMT) analysointiin langattomiin tandem MIMO välitysverkkoihin, olettaen välittäjien käyttävän käytännöllisiä full-duplex lähetystekniikoita, jotka mahdollistavat valinnan joko full-duplex tai half-duplex lähetystilan välillä. Analyysin perusteella kontribuoimme seuraavilla tavoilla: Ensinnäkin, vertailemme perusteellisesti full-duplex sekä half-duplex lähetystiloja langattomissa tandem välitysverkoissa. Huomaamme, että molemmat full-duplex ja half-duplex lähetystilat voivat suoriutua toinen toistaan paremmin. Tarkemmin sanoen, monissa tandem välitysverkoissa silloin kun multipleksoinnin hyöty on alhainen, paras välitystapa on antaa kaikkien välittäjien käyttää half-duplex lähetystilaa, koska silloin saavutetaan paras diversiteettilisäys. Toisaalta, kun multipleksointilisäys on suuri, paras diversiteettilisäys saadaan yleensä asettamalla jotkin välittäjät full-duplex lähetystilaan. Lisäksi, tutkimme kuinka full-duplex lähetystilaa käyttävien välittäjien jäljelle jäävä interferenssi vaikuttaa tandemverkon DMT:aan. Huomaamme, että jäljelle jäävä interferenssi vähentää full-duplex mallin tehokkuutta ja lisäksi vaikuttaa optimaaliseen tehonjakamiseen verkossa. Tarkemmin sanoen, jos jäljelle jäävä interferenssin tehotaso on nolla tai tarpeeksi lähellä sitä, lineaarisella tehojaolla voi saavuttaa verkon optimaalisen DMT:n. Muutoin, optimaalinen DMT saavutetaan epälineaarisella tehojaolla. Lopuksi, DMT analyysi havainnollistaa tehokkaan periaatteen yleisluontoisten monihyppyverkkojen käsittelemiseen, eli verkon jakamisen pienempiin osiin erilaiin avainrakenteisiin. Tämän jälkeen yleisluntoisten langattoimen monihyppyverkkojen tutkiminen tapahtuu tutkimalla näitä pieniä osia ja niiden välisiä vuorovaikutussuhteita. Langattomaan kahden hypyn monilähetysvälitysverkkon osalta keskitymme tapaustutkimukseen, jossa yksi lähettäjä monilähettää kahdelle vastaanottajalle kahden välittäjän avulla. Ehdotamme tälle verkolle osittaista decode-and-forward protokollaa, joka sisältää täyden decode-and-forward protokollan erikoistapauksena ja saavuttaa yleisesti tätä protokollaa paremman tehokkuuden. Tarkemmin sanoen, todistamme että tällä protokollalla siirtonopeus lähetystehon suhteen joko lähenee asymptoottisesti verkon cut-set ylärajaa mielivaltaisen lähelle tai saavuttaa sen 1 bit/s/Hz sisään. Osoitamme myös, että osittainen decode-and-forward protokolla voi saavuttaa verkon optimaalisen DMT:n. Tämän jälkeen, käsittelemme osittaisen decode-and-forward strategian impelentointia yleisluontoisille monilähetysvälitysverkoille.

En raison de leurs excellentes propriétés mécaniques, couplées à une bonne résistance à la corrosion par piqûres et à un coût modéré (basse teneur en nickel et en molybdène), les aciers inoxydables austéno-ferritiques (dits aciers inoxydables duplex) sont largement utilisés dans de nombreux secteurs industriels. Les aciers inoxydables duplex ont une microstructure complexe composée à proportion équivalente d’austénite et de ferrite. L’austénite ayant une composition chimique différente de celle de la ferrite, un film hétérogène se forme à la surface des aciers inoxydable duplex. Par ailleurs, les deux phases métalliques ayant des propriétés mécaniques différentes, un champ de contraintes hétérogènes est généré dans les grains. Sous certaines conditions, l’existence de gradients de contraintes peut conduire à des hétérogénéités du film passif. Dans cette étude, l’effet d’un vieillissement de longue durée dans un milieu contenant des chlorures sur la composition chimique du film passif a été tout d’abord étudié. Le comportement en corrosion de certains alliages duplex a été ensuite déterminé à partir d’essais TCP (détermination de la température critique de piqûration). Les résultats ont été analysés en tenant compte des informations obtenues précédemment. Après vieillissement, l’épaisseur du film passif et le rapport Cr/Fe ont significativement augmenté. La distribution des chlorures dans le film passif est hétérogène. Cette distribution a été reliée à la microstructure du matériau et au champ de contraintes résiduelles. Il a été montré qu’elle influence le comportement électrochimique du matériau. Le comportement en corrosion est ensuite analysé à l’aide des courbes de polarisation locales. Des critères métallurgiques ont été proposés pour l’amorçage de piqûres. / Duplex stainless steels (DSS) are highly important engineering materials, due to their generally high corrosion resistance combined with high strength and moderate alloy cost (lower nickel and molybdenum content). They are widely used in various industrial sectors. DSS have a complex microstructure with comparable volume of austenite and ferrite. Due to differences in chemical composition between austenite and ferrite, a heterogeneous passive film is formed on both phases. In addition, due to differences in mechanical properties, a heterogeneous stress field may be generated in metallic grains. Under certain conditions, these differences may also yield formation of a heterogeneous passive film. In this work, the influence of long-term ageing in chloride-containing media by on the chemical composition of the passive film was first studied by means of XPS and Auger at the microscale. The corrosion behaviour of some duplex stainless steels was then determined from CPT tests (determination of the critical pitting temperature). Results were analysed taking into account information obtained previously. After ageing, the thickness and the ratio Cr/Fe are significantly increased. The chloride distribution in the passive film was heterogeneous. It was related to the microstructure and the residual strain field. It was shown that this distribution modifies the electrochemical behaviour of samples. The corrosion behaviour was then analysed from local polarization curves and CPT tests. Metallurgical criteria for pitting were proposed.

<p>A wireless revolution has occurred resulting in the formation of a proverbial backbone of wireless devices that our everyday functionality, productivity, and general way of life have become dependent. Consequently, victimizing an already constrained and finite wireless spectrum with further demands for increased bandwidths, greater channel capacities, and an insatiable plea for faster access rates. In-band full-duplexing (IBFD) is an innovative and encouraging technology that aims to answer this tacit mitigation call by bolstering spectral efficiency through simultaneous same frequency band transmission and reception. Conventionally, transceiver-based systems have their respective transmission and reception dictated by occurring in either disparate time slots (half-duplex) or distinct frequencies (out-of-band full-duplex). By achieving simultaneous same band communication, a theoretical doubling in spectral efficiency is rendered feasible. However, transmitter to receiver leakage, or self-interference (SI), remains the most barring frustration to IBFD realization. Being locally generated, SI is considerably stronger (often 50-100dB) than the desired signal-of-interest (SOI). Left unresolved, this unwanted energy saturates the receiver’s amplifiers and desensitizes its analog-to-digital converters. Thus, rendering the SOI unintelligible. Therefore, a means of self-interference cancellation (SIC) is necessitated to suppress any polluting SI to levels that of or below the receiver’s noise floor.</p><p></p>In this thesis an in-depth history of in-band full duplex technology is first presented, followed by a condensed examination of the SIC domains. Pertinent theory is presented pertaining to noise analysis and estimation relevant to a proposed IBFD transceiver architecture. Finally, a modelled simulation of this transceiver, developed in MATLAB, is presented. Subsequent results detailing an investigative study done on a fully adaptive tapped-branch analog self-interference canceller are shown. Said canceller’s variable phase and amplitude weights are set via real-time training using gradient descent algorithms. Evaluation of the results reveal marginal effect on the SIC efficacy due to transmission path nonlinearity and noise distortions alone. However, expansion of model consideration for conceivable cancellation hardware nonlinearities reveals an indirectly proportional degradation of SIC performance by up to 35dB as distortion levels vary from -80 dBm to -10 dBm. These results indicate consideration of such non-idealities should be an integral part of cancellation hardware design for the preclusion of any intrinsic cancellation impediments.

Introduktion: Polymerase chain reaction (PCR) är en biokemisk och molekylärbiologisk laboratorieteknik som används för in vitro amplifiering av specifika gensekvenser. Det finns olika varianter av PCR, en mer utvecklad version är Realtids-PCR, även benämndkvantitativ PCR (qPCR). qPCR mäter fluorescensintensitet i varje qPCR cykel. Metoden delas in i fyra huvudfaser: linjär-, tidig exponentiell-, exponentiell- och platåfas.   Syfte: Syftet med projektet var att utvärdera prestanda hos Quantstudio 7 vid varierande reaktionsvolym och plattposition, samt vid singleplex och duplex, för att öka kvaliteten på resultat och göra metoden mer kostnadseffektiv.   Material &amp; metod: Syntetisk DNA-sekvens (gBlock) späddes och sattes upp i en standardkurva med sju punkter och användes för 20 µl respektive 10 µl reaktionsvolymen, varje punkt bestod av 4 replikat. För att utvärdera Duplex vs Singelplex förbereddes standardkurva i kombination med en konstant koncentration av en annan assay. För att undersöka intra-plate variation sattes upp identiska reaktioner i samtliga brunnar i PCR-plattan.    Resultat: Samtliga experiment gav detekterbara ampliferingsprodukter.  Cq-värdet användes för att beräkna medelvärde och standardavvikelse, samt effektivitet och R2-värde   Slutsats: Resultatet som erhålls från QS instrumentet visade att reaktionsvolymerna 10 µl och 20 µl är jämförbara. Duplex experimentet visade att gener med låg genuttryck kan duplexas med gener som har 10 000x högre genuttryck. Resultatet från intra-plate variation visade att variationen i SD var högre i den högre sidan av PCR-plattan. / Introduction: Polymerase chain reaction (PCR) is a biochemical and molecular laboratory technique that is used for amplification of specific gene sequences. There are different variants of PCR. A more developed version is quantitative PCR (qPCR). In qPCR the fluorescence intensity is measured in realtime during each qPCR cycle.    Aim: The purpose of the project is to evaluate whether the reaction volume can be reduced by half, which leads to using less material and thus make the method more cost-effective.   Matherial &amp; method: Synthetic DNA sequence (gBlock) was diluted and set up in a standard curve with seven standards and used for 20 μl and 10 μl reaction volume, respectively. Each standard consisted of 4 replicates. To evaluate Duplex vs Singelplex, standard curve was prepared in combination with a constant concentration of another assay. To investigate intra-plate variation, identical reactions were set up in all wells of the PCR-plate.   Results: All experiments yielded detectable amplification products. The Cq value was used to calculate the mean and standard deviation, as well as the efficiency and R2 value   Conclusion:  The obtained results showed that the reaction volumes 10 and 20 µl are comparable. In duplex assay, genes with low gene expression can be analyzed with genes that have 10,000x higher gene expression. In intraplate-assay variation, the variation in the standard deviation increased in the right side of PCR-plate.

Legeleistungseinbußen – vor allem mit verminderter Eischalenqualität – stellen in einem Legehennenbetrieb hohe wirtschaftliche Verluste dar. Impfungen gegen entsprechende Erreger, u.a. gegen das aviäre Metapneumovirus (aMPV), sind daher weit verbreitet. AMPV ist seit den 70er Jahren als Auslöser der Rhinotracheitis der Puten (Turkey Rhinotracheitis; TRT) und des sogenannten Swollen Head Syndroms (SHS) der Hühner bekannt. Jedoch liegen nur wenige epidemiologische Studien zu der Verbreitung des Virus und dessen Subtypen in Legehennenbetrieben vor. Ziel der vorliegenden Studie war es daher, die Verbreitung des aMPV, vor allem der Subtypen A und B, zu unterschiedlichen Zeiten der Legeperiode zu untersuchen, um ein besseres Verständnis über den Zeitpunkt der Erstinfektionen sowie evtl. Re- oder Neuinfektionen zu erhalten. Dafür wurden erstmals 18 Legehennenherden in Sachsen alle drei Monate über die gesamte Legeperiode auf das Vorkommen von aMPV-RNA und aMPV-spezifischer Antikörper untersucht. Verschiedene Haltungssysteme wurden berücksichtigt, um ein unterschiedliches seuchenhygienisches Risiko unter Praxisbedingungen bewerten zu können. Pro Herde wurden von je zehn Hühnern Trachealtupfer und Serumproben entnommen. Die Tupferproben wurden mittels duplex nested RT-PCR untersucht, die Serumproben mittels zweier kommerzieller ELISA-Tests. In jeder Herde gelang der aMPV-RNA-Nachweis mindestens einmal zu unterschiedlichen Zeitpunkten. Bereits bei der Einstallung konnten in 17 Herden aMPV-spezifische Antikörper und/oder aMPV-RNA nachgewiesen werden. Diese Ergebnisse zeigen die hohe Verbreitungsrate des aMPV in Legehennenbetrieben. Bereits in der Aufzucht fand in der Mehrzahl der Herden eine aMPV-Infektion statt; während der Legeperiode kam es zu häufigen Re- oder Neuinfektionen bzw. zu einer langen Persistenz des Virus. Subtyp A kam alleine (51%) mehr als doppelt so häufig vor wie ausschließlich Subtyp B (22%). Doppelinfektionen mit den Subtypen A und B (27%) wurden ungefähr so häufig gefunden wie eine Infektion ausschließlich mit Subtyp B. Ein Wechsel der Subtypen A und B während einer Legeperiode wurde am häufigsten beobachtet: zehn der 18 Herden (56%) zeigten diesen Verlauf. Ausschließlich Subtyp A in allen positiven Entnahmen pro Betrieb wurde in vier von 18 Herden gefunden, ausschließlich Subtyp B in drei von 18 Herden, Subtyp A gemeinsam mit Subtyp B in einer von 18 Herden. Dies verdeutlicht die Dominanz des Subtyps A in Legehennenbetrieben. Obwohl drei Herden während der Aufzucht mit einer Subtyp B-Vakzine geimpft wurden, gelang der aMPV-RNA Nachweis in bis zu vier Probenentnahmen. Der Subtyp A dominierte auch in den geimpften Herden. Neben dem Subtyp B Feldvirus wurde in einer Herde zum Zeitpunkt der Einstallung auch ein Subtyp B ähnlich dem Impfstamm nachgewiesen. Es ist daher davon auszugehen, dass trotz bekannter Kreuzimmunität eine Impfung nicht vor Infektionen schützt, aber die Persistenz von Subtyp B vermindert. Die Analyse der Serumproben mit zwei kommerziellen ELISA-Tests ergab zum Teil konträre Ergebnisse. Da die Diagnose einer aMPV-Infektion häufig nur über diese Methode gestellt wird, ist dies von praktischer Relevanz. Eine Evaluierung des ELISA-Tests mit der höchsten Spezifität und Sensitivität sollte daher folgen.

In our thesis work, we analyze the performance analysis of a power domain NonOrthogonal Multiple Access (NOMA) system in which the closer user acts as fullduplex relaying to forward the signal to farther user. Because Nakagami-m distribution is a generalized case including the two common fading distributions as specialcases: Rayleigh distribution (m=1), Rician distribution (m&gt;1). We assume that thesystem experiences Nakagami-m fading. Then, we have to analyze outage probabilityof NOMA system. Numerical results are provided for outage probability to show theeffect of system parameters on the performance of the NOMA system in full duplexrelaying over Nakagami-m fading.

[pt] A exposição de aços a condições de geração de hidrogênio, como em ambientes que contenham H2S ou sob proteção catódica, pode provocar o aumento do teor de hidrogênio na sua superfície, fragilizando o material. Foi desenvolvido um estudo com o objetivo de comparar o comportamento das microestruturas de dois diferentes aços inoxidáveis, um austenítico de classe P550 e um duplex S31803, com relação à permeação e consequente fragilização pelo hidrogênio. Os aços foram testados nas condições com e sem solda autógena utilizando os mesmos parâmetros de soldagem. Foram realizados análise microestrutural por MO, MEV e MET, ensaios de tração, ensaios de BTD com os corpos de prova imersos em solução de água do mar sintética e sob aplicação de potencial catódico de -1200 mV SCE, com o objetivo de simular condições de serviço e fractografia por MEV dos corpos de prova ensaiados por BTD. Observou-se que ambas as classes de aços sofreram alguma fragilização, no entanto, com relação à perda de ductilidade em função da redução de área dos corpos de prova, esta ocorreu de forma mais pronunciada para o aço inoxidável duplex. Foi observado que o aço austenítico no metal de base continha maior densidade de maclas do que o metal de solda, resultando em maior fragilização. Além disto, no metal de base, observou-se mais alta densidade de discordâncias e de precipitados. O aço duplex, por outro lado, apresentou fragilização muito maior do que o austenítico em ambas as condições quando permeado pelo hidrogênio. No entanto, esta fragilização foi mais pronunciada na condição de como soldado. Atribuiu-se este comportamento à ferritização parcial da estrutura e à formação de austenita Widmanstätten. As análises fractográficas sugerem a alteração do mecanismo de fratura dos corpos de prova de dúctil, quando ensaiados ao ar, para frágil, na condição de ensaio com geração de hidrogênio. Esta observação fundamenta-se no fato de que as superfícies de fratura de todos os corpos de prova ensaiados ao ar são formadas predominantemente por dimples (dúctil), enquanto no ensaio com geração de hidrogênio, as superfícies de fratura se apresentam com aspecto frágil de diferentes formas para cada aço. / [en] Steel exposure to hydrogen generation conditions, such as in environments containing H2S or under cathodic protection, can cause an increase in the hydrogen content on the surface which leads to the material embrittlement. A comparative study was carried out on the structure behavior of two different stainless steels, an austenitic class P550 and a duplex S31803, concerning permeation and consequent hydrogen embrittlement. The steels were tested in conditions with and without autogenous welding using the same welding parameters. It was performed microstructural analysis by OM, SEM and TEM, tensile tests, BTD tests with the specimens immersed in a synthetic seawater solution and under application of a cathodic potential of -1200 mV SCE, in order to simulate service conditions, and surface fractography of these specimens by SEM. It was observed that both grades of steel suffered some fragility. However, the loss of ductility due to the reduction of the area of the specimens occurred in a more pronounced way for the duplex stainless steel. It was also observed that the austenitic steel in the base metal contained a higher density of twinnings than the weld metal, resulting in greater embrittlement. In addition, a higher density of dislocations and precipitates was observed in the base metal. On the other hand, duplex steel showed much more significant embrittlement than austenitic in both conditions when permeated by hydrogen. However, this weakness was more pronounced in the as welded condition. This behavior was attributed to the partial ferritization of the structure and the formation of Widmanstätten austenite. Fractographic analyzes suggest that the fracture mechanism morphology changed from ductile to brittle when the specimens were tested in the air and hydrogen condition respectively. This observation is based on the fact that the fracture surfaces of all samples tested in the air consisted predominantly of dimples (ductile). In contrast, in the test with hydrogen generation, the fracture surfaces appear with different brittle morphologies for each steel.