Electrochemical deposition finds applications in the electronics- and protective coating industries. The technique is a versatile tool for the synthesis of alloys and thin films. Knowledge of the fundamental aspects of the electrode processes enables the design of nanostructured materials. In this thesis, electrodeposition processes in solutions containing metal ion complexes were studied and new methods for the preparation of metal/metal-oxide coatings were developed and evaluated. Metal/metal oxide coatings were electrodeposited from aqueous solutions containing metal complexes of hydroxycarboxylic acids under reducing conditions. The mass changes of the working electrode were monitored in-situ with the electrochemical quartz crystal microbalance (EQCM) technique and ellipsometry was used to detect the formation of Cu2O. The coatings were further characterized with XRD, XPS, SEM, TEM, and Raman spectroscopy. Electrochemical methods, including reduction of Sb/Sb2O3 in an organic electrolyte, were also used to study the properties of the deposited materials. Nanostructured coatings of Cu/Cu2O were obtained during spontaneous potential or current oscillations in alkaline Cu(II)-citrate solutions. The oscillations were due to local pH variations induced by a subsequent chemical step and comproportionation between Cu and Cu2+. Well-defined layers of Cu and Cu2O could be prepared by a galvanostatic pulsing technique, allowing independently controlled thickness of several hundred nanometers. Coatings, containing Sb and co-deposited, nanograins of Sb2O3, with a thickness of up to 200 nm were prepared from poorly buffered Sb(III)-tartrate solutions. Galvanostatic cycling showed that the latter material could be reversibly charged and discharged in a Li-ion battery for more than 50 cycles with a capacity of 660 mAh/g. The results show that precipitations of metal oxides can occur due to local pH increases during electrochemical deposition from metal complexes with ligands containing hydroxyl groups. The ability to deposit metal oxides using cathodic deposition relies on a sufficiently slow reduction of the oxide.

The electrochemical quartz crystal microbalance (EQCM) has been proven an effective mean of monitoring up to nano-scale mass changes related to electrode potential variations at its surface. The principles of operation are based on the converse piezoelectric response of quartz crystals to mass variations on the crystal surface. In this work, principles and operations of the EQCM and piezo-electrodes are discussed. A conductive oxide, ruthenium oxide (RuO2) is a promising material to be used as a diffusion barrier for metal interconnects. Characterization of copper underpotential deposition (UPD) on ruthenium and RuO2 electrodes by means of electrochemical methods and other spectroscopic methods is presented. Copper electrodeposition in platinum and ruthenium substrates is investigated at pH values higher than zero. In pH=5 solutions, the rise in local pH caused by the reduction of oxygen leads to the formation of a precipitate, characterized as posnjakite or basic copper sulfate by means of X-ray electron spectroscopy and X-ray diffraction. The mechanism of formation is studied by means of the EQCM, presenting this technique as a powerful in-situ sensing device.

Electrochemical quartz crystal microbalance has been employed to investigate electro-responsiveness of an ionic liquid as an additive in lubricant oils on a gold surface. Polarisation of the surface reveals changes in frequency where an increase in magnitude amplified the observed response, corresponding to a controllable alternation of the ionic liquid configuration on the surface as a function of applied potential. The frequency changes are due to different packing of the anion and cation, respectively, on the surface as their mass densities and geometries are different. Relaxation of the system was reversible to the application of a potential and it was also found to be diffusion dependent, where the ratio between the ion diffusivities could be extracted from the results. Measurement of the system relaxation reveals a potential decay of that of a discharging capacitor, with an internal resistance inducing an initial potential drop due to the resistivity of the oil medium. The discharge behaviour was also proven to show high internal reproducibility validity within experiments. This newly discovered insight in responsive differences of ion packing is of importance, not only for ionic liquid additives in tribology, but for understanding and exploiting ionic liquids in an array of electrochemical applications.

No description available.

Although the passive films that form on stainless steels have been extensively studied, the concentration depth profiles are not fully understood. Their thinness makes passive films hard to study, but angle-resolved X-ray photoelectron spectroscopy (ARXPS) is a non-destructive technique that can be used to obtain depth information. An iterative approach to deconvolute ARXPS measurements into depth profiles is discussed, and the chemistry of passive films on a molybdenum-containing 316L stainless steel is investigated. Bipolar electrochemistry, in which the sample is placed along an electric field created by two driving electrodes in an electrolyte, is investigated as a screening tool. It is shown that the method is useful to create corrosion gradients on 304 stainless steel, both under pitting and non-pitting conditions. Chromium carbide thin films were deposited by magnetron sputtering with a variety of deposition parameters on stainless steel, and subsequently analyzed. It is shown that these films present a promising material system for protective coatings to improve the corrosion resistance of stainless steels while also maintaining other useful properties, such as low interfacial contact resistance. Particular attention is given to the electrochemical evaluation of the films, whose high carbon concentrations necessitates different interpretations of the electrochemical results compared to for stainless steels.

This dissertation is focused on the study of selected additives and their effect on positive and negative electrodes of Ni-Zn secondary cells. The first group of additives consists of the inorganic compounds that reduce zinc oxide solubility and thus prevents shape changes of the zinc electrode. The second group contains organic additives that have the beneficial effect of dendrite growth prevention. All additives were examined in relationship to their compatibility with the positive electrode and to their effect on the zinc electrode dendrites inhibition, hydrogen evolution and corrosion inhibition. Moreover, the study of decomposition kinetics of supersaturated zincate solution with the first group of additives was performed. Finally, a short study of pulse regime charging mode with regard to dendrites inhibition was performed and evaluated.

No description available.

The Electrochemical Quartz Crystal Microbalance (EQCM) was used as the main investigation tool coupled with other conventional electrochemical methods to study the electrocatalytic properties of polycrystalline Pt electrodes, including two separate projects. The first project studied the early stage of oxide film formation on the Pt surfaces and the inhibition of the catalytic properties by the oxide film. The inhibition of the fast electrode reaction of small molecules by the growth of oxide film allows those molecules to be used as probes for the nature of the oxide film. The hydrogen oxidation current, jox calculated by differencing the cyclic voltammetry currents with and without H₂ present showed a characteristic plateau-to-plateau profile, which implies a transition from the free Pt surface to the Pt surface completely covered by oxide film. This method allows determination of the onset potential for oxide formation and also the critical potential where a full monolayer of oxide is formed. This method applies to other fast surface reactions such as oxygen reduction reaction (ORR), and the results are enhanced by forced convection in the rotating disk electrode (RDE) experiments. The initial oxidation species was identified by charge and EQCM frequency analysis. Our results support the formation of a species with stoichiometry Pt₂O, for example, with an oxygen atom in the bridging position between two adjacent Pt atoms. In the second project, the stability of the Pt electrodes in acid media with Ag⁺ present was investigated. A substantial frequency drift (8.3 Hz cycle⁻¹, or 44 ng cm⁻² cycle⁻¹) was observed during Ag electrodeposition and stripping on the bare polycrystalline Pt surface. Cyclic voltammograms in pure HClO₄ solution showed nearly no frequency drift while the addition of 10⁻³ mol L⁻¹ Ag⁺ resulted in an immediate and characteristic frequency drift. The frequency drift appeared to be consistent with loss of material from the electrode surface and the ICP-MS detected a maximum Pt concentration of 2.3×10⁻⁶ mol L⁻¹ in solution due to Pt dissolution. The Pt concentration calculated from the EQCM frequency drift matched the ICP-MS results. This allowed the EQCM for direct investigation of Pt dissolution at different system temperatures, sweep rates, and potential ranges. The much higher rate of dissolution with Ag present than that in pure HClO₄ solution can be explained by the formation of Pt-Ag alloy during Ag underpotential deposition and the co-dissolution of Pt and Ag.

Lithium-oxygen batteries, also known as Lithium-air batteries, could possibly revolutionize energy storage as we know. By letting lithium react with ambient oxygen gas very large theoretical energy densities are possible. However, there are several challenges remaining to be solved, such as finding suitable materials and understanding the reaction, before the lithium-oxygen battery could be commercialized. The scope of this thesis is focusing on the latter of these challenges. Efficient ion transport between the electrodes is imperative for all batteries that need high power density and energy efficiency. Here the mass transport properties of lithium ions in several different solvents was evaluated. The results showed that the lithium  mass transport in electrolytes based on the commonly used lithium-oxygen battery solvent dimethyl sulfoxide (DMSO) was very similar to that of conventional lithium-ion battery electrolytes. However, when room temperature ionic liquids were used the performance severely decreased. Addition of Li salt will effect the oxygen concentration in DMSO-based electrolytes. The choice of lithium salt influenced whether the oxygen concentration increased or decreased. At one molar salt concentration the highest oxygen solubility was 68 % larger than the lowest one. Two model systems was used to study the electrochemical reaction: A quartz crystal microbalance and a cylindrical ultramicroelectrode. The combined usage of these systems showed that during discharge soluble lithium superoxide was produced. A consequence of this was that not all discharge product ended up on the electrode surface. During discharge the cylindrical ultramicroelectrodes displayed signs of passivation that previous theory could not adequately describe. Here the passivation was explained in terms of depletion of active sites. A mechanism was also proposed. The O2 and Li+ concentration dependencies of the discharge process were evaluated by determining the reactant reaction order under kinetic and mass transport control. Under kinetic control the system showed non-integer reaction orders with that of oxygen close to 0.5 suggesting that the current determining step involves adsorption of oxygen. At higher overpotentials, at mass transport control, the reaction order of lithium and oxygen was zero and one, respectively. These results suggest that changes in oxygen concentration will influence the current more than that of lithium. During charging not all of the reaction product was removed. This caused an accumulation when several cycles was examined. The charge reaction pathway involved de-lithiation and bulk oxidation, it also showed an oxygen concentration dependence. / Litiumsyrebatteriet, även känt som litiumluftbatteriet, kan potentiellt revolutionera vårt förhållande till energilagring. Genom att låta litium reagera med syrgas från luften kan teoretiskt höga energitätheter uppnås. Dock så behöver många problem lösas, så som att hitta lämpliga elektrod- och elektrolytmaterial samt att få en ökad förståelse för reaktionsmekanismen, innan litiumsyrebatteriet kan kommersialiseras. Den här avhandlingen behandlar de sistnämnda av dessa problem. För att ett batteri ska kunna leverera hög effekttäthet och energieffektivitet krävs en effektiv jontransport mellan elektroderna. Här utvärderades masstransporten hos flera olika elektrolyter. Resultatet visade att masstransporten av litium i en litiumsyrebatterielektrolyt (baserad på dimetylsulfoxid (DMSO)) är likvärdig med en konventionell litiumjonbatterielektrolyt. När elektrolyter baserade på jonvätskor användes uppvisades väldigt stora energiförluster. När litiumsalt tillsattes påverkades lösligheten av syre i DMSO-baserade elektrolyter. Vilken sorts litiumsalt som användes påverkade om lösligheten av syre ökade eller minskade. Vid en saltkoncentration på en molar var den högsta syrelösligheten 68 \% större än den lägsta. Två olika modellsystem används för att studera den elektrokemiska reaktionen: En elektrokemisk kvartskristallmikrovåg och en cylindrisk ultramikroelektrod. Vid kombinerad användning av dessa system påvisades att löslig litiumsuperoxid bildades vid urladdningen. Följden av detta blev att endast delar av urladdningsprodukten hamnade på elektroden. Vid urladdning visade ultramikroelektroderna tecken på passivering som inte kunde beskrivas av tidigare teori. Här föreslås att passiveringen uppstår på grund av en blockering av de aktiva säten där reaktionen fortskrider. För denna process föreslås även en detaljerad mekanism. Urladdningsprocessens koncentrationsberoende utvärderades genom att bestämma reaktionsordningen för syre och litium under kinetisk- och masstransport kontroll. Under kinetisk kontroll fanns inga heltalsreaktionsordningar, för syre var reaktionsordningen nära 0.5 vilket föreslår att det reaktionssteg som bestämmer strömstorleken innefattar en adsorption av syre. Vid högre överpotentialer, då systemet var under masstransportkontroll, var reaktionsordningarna för litium och syre noll respektive ett. Detta föreslår att ändringar i syrekoncentration påverkar strömmen betydligt mer än vad det gör för litium. Under uppladdning kunde inte all reaktionsprodukt avlägsnas från elektroden. Detta ledde till en ackumulation då flera cykler studerades. Uppladdningens delsteg innefattade en delitiering följt av en oxidation av reaktionsproduktbulken. Denna process uppvisade även ett syrekoncentrationsberoende. / <p>QC 20171114</p>

The control of interfacial microstructural stability is of utmost importance to the reliability of liquid solder interconnects in high temperature electronic assemblies. This is primarily due to excessive intermetallic compounds (IMCs) that can form and continuously grow during high temperature operation, which practically renders conventional barrier metallisations inadequate. In this study, electrically conducting, NbOx containing Ni coatings were developed using electrodeposition. Their suitability as a solder diffusion barrier layer was assessed in terms of the electrical conductivity and barrier property. The present work explores a novel electrochemical route to produce Ni-NbOx composite coatings of good uniformity, compactness and purity, from non-aqueous glycol-based electrolytes consisting of NiCl2 and NbCl5 as metal precursors. The effects of cathodic current density and NaBH4 concentrations on the surface morphology, composition and thickness of the coatings were examined. A combined study of Scanning Transmission Electron Microscopy (STEM) and Electrochemical Quartz Crystal Microbalance (EQCM) was conducted to understand the fundamental aspects of this novel electrodeposition process. The composite coatings generally exhibited good electrical conductivity. The reaction behaviour between a liquid 52In-48Sn solder and Ni-NbOx, with Nb contents up to 6 at.%, were studied at 200°C. The results indicate that, Ni-NbOx with sufficient layer thickness and higher Nb content, offered longer service lifetime. Nb enrichment was generally observed at or close to the reaction front after high temperature storage, which suggests evident effectiveness of the enhanced diffusion barrier characteristics.