Spelling suggestions: "subject:"energyharvesting"" "subject:"overharvesting""
461 |
Toward an energy harvester for leadless pacemakersDeterre, Martin 09 July 2013 (has links) (PDF)
This work consists in the development and design of an energy harvesting device to supply power to the new generation pacemakers, miniaturized leadless implants without battery placed directly in heart chambers. After analyzing different mechanical energy sources in the cardiac environment and associated energy harvesting mechanisms, a concept based on regular blood pressure variation stood out: an implant with a flexible packaging that transmits blood forces to an internal transducer. Advantages compared to traditional inertial scavengers are mainly: greater power density, adaptability to heartbeat frequency changes and miniaturization potential. Ultra-flexible 10-µm thin metal bellows have been designed, fabricated and tested. These prototypes acting as implant packaging that deforms under blood pressure actuation have validated the proposed harvesting concept. A new type of electrostatic transducer (3D multi-layer out-of-plane overlap structure with interdigitated combs) has been introduced and fully analyzed. Promising numerical results and associated fabrication processes are presented. Also, large stroke optimized piezoelectric spiral transducers including their complex electrodes patterns have been studied through a design analysis, numerical simulations, prototype fabrication and experimental testing. Apower density of 3 µJ/cm3/cycle has been experimentally achieved. With further addressed developments, the proposed device should provide enough energy to power autonomously and virtually perpetually the next generation of pacemakers.
|
462 |
A Mems Thermoelectric Energy Harvester For Energy Generation In Mobile SystemsTopal, Emre Tan 01 September 2011 (has links) (PDF)
In this thesis design, optimization, fabrication and performance characterization of MEMS thermoelectric (TE) energy harvesters for harnessing waste heat in mobile systems are presented. As a proof of concept, chromium and nickel are used as the thermoelectric material in the proposed design. The feasibility of the state of the art thermoelectric materials is also discussed.
MEMS TE energy harvesters proposed in this study are designed to generate power at relatively lower &Delta / T values. The performance of the MEMS TE energy harvesters was optimized using analytical and 3-D finite element models. An analytical code was used for profiling the electrical power output with varying geometry. The design points with maximum generated power were selected, and the microfabricated thermoelectric energy harvesters were designed accordingly. The fabricated devices are formed on a silicon wafer and composed of Nickel and Chromium thermocouples on SiO2/Si3N4 diaphragms, and Titanium heater and monitor resistors for testing purposes.
Microfabrication was followed by the performance characterization of MEMS TE energy harvesters with the conducted tests. For 10 ° / C temperature difference between the hot and cold junctions (a heat source at 35 ° / C), the proposed TE energy harvesters are capable of providing 1.1 µ / W/cm2 power density and 1.71 V voltage. The performance of the thermoelectric generators in general is limited by Carnot cycle efficiency. Nevertheless, the validated practical performance of MEMS TE energy harvesters proposed in this thesis is comparable to other examples in literature. It is anticipated by the calculations that this design will be able to provide the highest thermoelectric efficiency factor (4.04 µ / W/K2cm2) among the lateral TE energy harvesters if thermoelectric materials having high Seebeck coefficient values (such as p-Si, n-Si, polysilicon, Bi2Te3 etc.) are used. According to the performance results, the MEMS TE energy harvesters can be implemented in mobile systems to convert waste heat into electricity. The fabrication process can be adapted to CMOS with some modifications if needed. The lateral MEMS thermoelectric energy harvesters can also be combined with vibration energy harvesters to realize multi-mode energy scavenging.
For prospective study, vertical thermoelectric generator configurations are also discussed in order to further increase the power density generated. The finite element simulations for proposed vertical configurations with air and water convection were completed. The vertical TE generators proposed can supply up to 4.2 mW/cm2 with a heat source at a temperature of 310 K.
|
463 |
Toward perpetual wireless networks: opportunistic large arrays with transmission thresholds and energy harvestingKailas, Aravind 11 May 2010 (has links)
Solving the key issue of sustainability of battery-powered sensors continues to attract significant research attention. The prevailing theme of this research is to address this concern using energy-efficient protocols based on a form of simple cooperative transmission (CT) called the opportunistic large arrays (OLAs), and intelligent exploitation of energy harvesting and hybrid energy storage systems (HESSs). The two key contributions of this research, namely, OLA with transmission threshold (OLA-T) and alternating OLA-T (A-OLA-T), offer an signal-to-noise ratio (SNR) advantage (i.e., benefits of diversity and array (power) gains) in a multi-path fading environment, thereby reducing transmit powers or extending range. Because these protocols do not address nodes individually, the network overhead remains constant for high density networks or nodes with mobility. During broadcasting across energy-constrained networks, while OLA-T saves energy by limiting node participation within a single broadcast, A-OLA-T optimizes over multiple broadcasts and drains the the nodes in an equitable fashion. Another important contribution of this research is the design and analysis of a novel routing metric called communications using HESS (CHESS), which extends the rechargeable battery (RB)-life by relaying exclusively with supercapacitor (SC) energy, and is asymptotically optimal with respect to the number of nodes in the network.
|
464 |
An electrostatic CMOS/BiCMOS Li ion vibration-based harvester-charger ICTorres, Erick Omar 11 May 2010 (has links)
The primary objective of this research was to investigate and develop an electrostatic energy-harvesting voltage-constrained CMOS/BiCMOS integrated circuit (IC) that harnesses ambient kinetic energy from vibrations with a vibration-sensitive variable capacitor and channels the extracted energy to charge an energy-storage device (e.g., battery). The proposed harvester charges and holds the voltage across the vibration-sensitive variable capacitor so that vibrations can induce it to generate current into the battery when capacitance decreases (as its plates separate). To that end, the research developed an energy-harvesting system that synchronizes to variable capacitor's state as it cycles between maximum and minimum capacitance by controlling each functional phase of the harvester and adjusting to different voltages of the on-board battery. One of the major challenges of the system was performing all of these duties without dissipating the energy harnessed and gained from the environment. Consequently, the system reduces losses by time-managing and biasing its circuits to operate only when needed and with just enough energy while charging the capacitor through an efficient inductor-based precharger. As result, the proposed energy harvester stores a net energy gain in the battery during each vibration cycle.
|
465 |
Range finding in passive wireless sensor networks using power-optimized waveformsTrotter, Matthew 14 November 2011 (has links)
Passive wireless sensor networks (WSNs) are quickly becoming popular for many applications such as article tracking, position location, temperature sensing, and passive data storage. Passive tags and sensors are unique in that they collect their electrical energy by harvesting it from the ambient environment. Tags with charge pumps collect their energy from the signal they receive from the transmitting source. The efficiency of converting the received signal to DC power is greatly enhanced using a power-optimized waveform (POW).
Measurements in the first part of this dissertation show that a POW can provide efficiency gains of up to 12 dB compared to a sine-wave input. Tracking the real-time location of these passive tags is a specialized feature used in some applications such as animal tracking. A passive WSN that uses POWs for the improvement of energy-harvesting may also estimate the range to a tag by measuring the time delay of propagation from the transmitter to the tag and back to the transmitter. The maximum-likelihood (ML) estimator is used for estimating this time delay, which simplifies to taking the cross-correlation of the received signal with the transmitted signal.
This research characterizes key aspects of performing range estimations in passive WSNs using POWs. The shape of the POW has a directly-measurable effect on ranging performance. Measurements and simulations show that the RMS bandwidth of the waveform has an inversely proportional relationship to the uncertainty of a range measurement. The clutter of an environment greatly affects the uncertainty and bias exhibited by a range estimator. Random frequency-selective environments with heavy clutter are shown to produce estimation uncertainties more than 20 dB higher than the theoretical lower bound. Estimation in random frequency-flat environments is well-behaved and fits the theory quite nicely. Nonlinear circuits such as the charge pump distort the POW during reflection, which biases the range estimations. This research derives an empirical model for predicting the estimation bias for Dickson charge pumps and verifies it with simulations and measurements.
|
466 |
Fundamentals of Heterogeneous Cellular NetworksDhillon, Harpreet Singh 24 February 2014 (has links)
The increasing complexity of heterogeneous cellular networks (HetNets) due to the irregular deployment of small cells demands significant rethinking in the way cellular networks are perceived, modeled and analyzed. In addition to threatening the relevance of classical models, this new network paradigm also raises questions regarding the feasibility of state-of-the-art simulation-based approach for system design. This dissertation proposes a fundamentally new approach based on random spatial models that is not only tractable but also captures current deployment trends fairly accurately.
First, this dissertation presents a general baseline model for HetNets consisting of K different types of base stations (BSs) that may differ in terms of transmit power, deployment density and target rate. Modeling the locations of each class of BSs as an independent Poisson Point Process (PPP) allows the derivation of surprisingly simple expressions for coverage probability and average rate. One interpretation of these results is that adding more BSs or tiers does not necessarily change the coverage probability, which indicates that fears of "interference overload" in HetNets are probably overblown.
Second, a flexible notion of BS load is incorporated by introducing a new idea of conditionally thinning the interference field. For this generalized model, the coverage probability is shown to increase when lightly loaded small cells are added to the existing macrocellular networks. This is due to the fact that owing to the smaller loads, small cells typically transmit less often than macrocells, thus contributing less to the interference power. The same idea of conditional thinning is also shown to be useful in modeling the non-uniform user distributions, especially when the users lie closer to the BSs.
Third, the baseline model is extended to study multi-antenna HetNets, where BSs across tiers may additionally differ in terms of the number of transmit antennas, number of users served and the multi-antenna transmission strategy. Using novel tools from stochastic orders, a tractable framework is developed to compare the performance of various multi-antenna transmission strategies for a fairly general spatial model, where the BSs may follow any general stationary distribution. The analysis shows that for a given total number of transmit antennas in the network, it is preferable to spread them across many single-antenna BSs vs. fewer multi-antenna BSs.
Fourth, accounting for the load on the serving BS, downlink rate distribution is derived for a generalized cell selection model, where shadowing, following any general distribution, impacts cell selection while fading does not. This generalizes the baseline model and all its extensions, which either ignore the impact of channel randomness on cell selection or lumps all the sources of randomness into a single random variable. As an application of these results, it is shown that in certain regimes, shadowing naturally balances load across various tiers and hence reduces the need for artificial cell selection bias.
Fifth and last, a slightly futuristic scenario of self-powered HetNets is considered, where each BS is powered solely by a self-contained energy harvesting module that may differ across tiers in terms of the energy harvesting rate and energy storage capacity. Since a BS may not always have sufficient energy, it may not always be available to serve users. This leads to a notion of availability region, which characterizes the fraction of time each type of BS can be made available under variety of strategies. One interpretation of this result is that the self-powered BSs do not suffer performance degradation due to the unreliability associated with energy harvesting if the availability vector corresponding to the optimal system performance lies in the availability region. / text
|
467 |
Développement de structures hybrides électromécaniques pour micro-sources d'énergie : générateurs piézoélectriques linéaires et non linéaires / Development of electromechanical hybrid structures for energy microsourcesHuet, Florian 14 December 2016 (has links)
La mise en œuvre de réseaux de capteurs communicants dans des installations industrielles, dans les transports ou le bâtiment apparaît comme un axe de développement qui permettrait d'augmenter les performances globales de ces systèmes.Par une supervision et une exploitation adaptées des informations collectées (température, niveau vibratoire, humidité, etc.), la fiabilité et les performances énergétiques pourraient être optimisées.La diminution régulière de la consommation des nouvelles générations de capteurs sans fil engendre un fort intérêt scientifique pour l'alimentation de ceux-ci de manière autonome. Ainsi, une thématique de recherche spécifique est apparue il y a une dizaine d'années : la réalisation de micro-sources d'énergie pour l'alimentation de capteurs communicants.Ces travaux de recherche proposent l'exploration des performances d'une structure de micro-générateur originale pour la récupération de l'énergie des vibrations : l'"Hybrid Fluid Diaphragm" (HFD).Le concept de l'HFD consiste à encapsuler un fluide incompressible entre deux membranes.Le fluide se comporte comme une masse inertielle qui induit une fréquence de résonance compatible avec les vibrations ambiantes dont les fréquences sont généralement inférieures à quelques centaines de Hertz.Ces membranes en P(VDF-TrFE), un polymère piézoélectrique, ont été réalisées spécifiquement pour assurer la conversion optimale des sollicitations mécaniques (flexion/tension) en énergie électrique.Une modélisation multiphysique qui intègre les comportements fluidiques, mécaniques et électriques, la réalisation et la caractérisation de deux générateurs HFD sont détaillées.Le premier prototype met en œuvre des membranes piézoélectriques monomorphes (monocouche) tandis que le deuxième exploite des membranes piézoélectriques bimorphes (double couche) optimisées.Les puissances générées apparaissent suffisantes pour envisager l'alimentation de capteurs et leurs géométries permettent d'imaginer des scénarios potentiels d'intégration dans des applications réalistes. / The implementation of wireless sensor nodes in industrial installations, transport or building is a potential route to increase the performances of these systems.By a proper supervision and exploitation of the collected information (temperature, vibratory level, humidity, etc.) the reliability and the energy performances can be increased. With the regular reduction of the power requirements for new generations of wireless sensors nodes, a strong scientific interest to develop autonomous power supply has raised.In this framework, a specific research topic appeared about ten years ago: ambient energy harvesting.The present work investigates the performances of an original micro-generator architecture for vibration energy harvesting: the “Hybrid Fluid Diaphragm” (HFD).The concept of HFD consists in encapsulating an incompressible fluid between two flexible membranes. The fluid behaves as an inertial mass which leads to a resonant frequency suitable for ambient vibrations whose spectrum is usually lower than a few hundred Hertz.These membranes are made of P(VDF-TrFE), a piezoelectric polymer, and are designed to ensure the optimal conversion of the mechanical solicitations (flexion/stretch) into electrical energy.A multiphysic modeling which integrates the fluid, the mechanical and the electric coupled behaviors is proposed.The realization and the characterization of two HFD's generators are detailed.A first prototype implements single layer piezoelectric membranes, whereas a second one uses optimized double layer membranes.The generated power appears to be sufficient to consider the power supply of wireless sensor nodes operating in intermittent transmitting mode. The very simple geometry of the proposed generators is favorable to their integration in realistic applications.
|
468 |
Contribution à la conception de générateurs hybrides souples : association de matériaux électro-actifs / Contribution to the design of soft hybrid generators : combination of electroactive materialsLagomarsini, Clara 11 January 2018 (has links)
Ces dernières années, les capteurs embarqués ont gagné en précision, fiabilité et robustesse, tout en se miniaturisant. Ces capteurs sont largement utilisés dans le domaine médical et sportif pour récolter toutes sortes de données physiologiques. Développer des générateurs d’énergie qui convertissent l’énergie mécanique ambiante en électricité constitue une voie très intéressante afin de rendre ces capteurs autonomes.Dans ce contexte, en 2013, un premier générateur souple autonome d’énergie a été développé au sein de notre équipe au G2Elab en collaboration avec le laboratoire LaMCoS. Ce générateur est conçu à partir d’élastomères électroactifs, basés sur la déformation de matériaux souples (polyacrylates, silicones) incorporés entre deux électrodes déformables et fonctionnent suivant un mode électrostatique. Ces structures présentent l’avantage d’être légères, peu chères, souples et elles peuvent être fabriquées suivant des géométries complexes. De plus, elles fonctionnent dans des gammes de fréquence basses (<100 Hz), les rendant ainsi attractives pour la récupération et la conversion d’énergie mécanique ambiante.L’objectif de ce travail de thèse était d’optimiser ce générateur pour en faire un générateur de seconde génération plus performant en terme d’énergie récupérée, beaucoup plus adaptable sur le corps humain et avec une durée de vie accrue. Pour atteindre ces différents critères, la conception et la réalisation de nouveaux dispositifs alternatifs hybridés pour des générateurs autonomes ont également été menées.Pour cela, la première étape a consisté à chercher un nouveau matériau pouvant remplacer le téflon comme électret dans la structure. Cet électret joue le rôle de réservoir de charges pour la polarisation du générateur fonctionnant en mode électrostatique. Le choix s’est porté sur plusieurs familles de poly(p-xylylene) plus communément appelées parylènes. Le fait de pouvoir les déposer dans un procédé CVD sur des géométries complexes et de façon très conforme a justifié ce choix. Le comportement temporel du potentiel de surface développé par ces électrets après une décharge couronne a été analysé en fonction du type et de l’épaisseur de parylène et du potentiel initial de charge. Cela a permis d’évaluer les potentialités en électret de ces matériaux et de mieux cerner la dynamique des charges électriques dans un environnement proche de l’application (sous contrainte mécanique) et pour des conditions plus extrêmes en température. Ces travaux ont permis de valider des parylènes fluorés comme d’excellents électrets (tests réalisés sur 1.5 an) tant en potentiel positif que négatif.La seconde étape s’est focalisée dans la conception de structures développant une architecture qui optimise les couplages électromécaniques au sein des matériaux constituant le générateur souple d’énergie. Dans ce but, et avec l’appui de modélisations que nous avons réalisées pour définir les géométries optimales de nos structures pour maximiser la puissance produite en sortie, deux principes de fonctionnement se sont dégagés : le premier fait appel à des électrets et il est ainsi en étroite continuité de l’étude précédente ; le second utilise des matériaux piézoélectriques (PZT et PVDF) comme source de polarisation ouvrant ainsi une nouvelle voie prometteuse de générateurs autonomes embarqués. Pour ces différentes structures, des prototypes de taille centimétrique ont été réalisés et caractérisés avec pour but final d’être insérés au niveau du genou pour récupérer la déformation mécanique lors de la marche ou de la course à pied. / Over the last years, wearable sensors have gained in accuracy and precision, while following the demands of miniaturization and lower power consumption. Scavenging human kinetic energy to produce electricity is an attractive alternative for the power supply of these low-power-consumption devices. E-textiles for health-monitoring or biomedical implants are some of the possible applications that could benefit from a self-powering system.In this context, in 2013, a first prototype of soft and autonomous energy scavenger was developed by our research group through the collaboration between LaMCoS and G2Elab laboratories. This electrostatic generator was based on the dielectric elastomers generators (DEGs) technology, which relies on the mechanical deformation of a thin layer of dielectric material (acrylic or silicone) sandwiched between two compliant electrodes. The main advantages of this technology are their low-cost, compliance, light-weight and adaptability to complex shapes. In addition, they can work on a large scale of temperatures and frequencies (<100Hz), which make them interesting to harvest and convert ambient mechanical vibrations.The objectives of this work were focused on the first prototype optimization to realize a second-generation device with higher energy output, suitability for wearable applications and lifetime and to conceive new alternatives hybrid devices for autonomous DEGs.To these aims, the first stage of the study consisted in the investigation of new conformant electret materials (representing the charges reservoir for electrostatic generator polarization) replacing Teflon in the scavenger structure. Different variants of poly(p-xylylene) polymers, better known with the commercial name of Parylene, were tested as new potential electret materials, mainly due to their highly conformability and possibility of CVD-deposition on complex shapes. The surface potential decays (SPD) on electrets formed by corona discharge method were monitored over time for different Parylene variants, samples thicknesses and charging voltages. These characterizations were aimed to evaluate the performance of Parylene electrets and to monitor the charge dynamic under mechanical conditions close to the final applications and under harsher environmental temperatures. As a result of these tests, fluorinated Parylenes showed excellent long-term charge retention performance (over 1.5 years) both for positive and negative charges.The second part of the work consisted in the realization of optimized structures realizing the electromechanical coupling of the two different electroactive materials constituting the soft electrostatic generator. For this aim, two different working modes were developed: the first one employs electret materials as polarization source, with the aim of optimizing the first hybrid device conceived in the previous study; the second one is made of piezoelectric materials (PZT and PVDF) as DEGs polarization sources, opening a new promising solution for autonomous wearable generators. Through numerical simulations, geometry optimization was performed with the aim of increasing the power output of the devices. Beneath, for the different structures, centimeter scale prototypes were realized and characterized with the final aim to be integrated at human knee level to exploit the mechanical deformation given by human body while walking.
|
469 |
Modélisations multi-physiques de la génération piezoélectrique à l'aide de nanofils d'oxyde de zinc / Multiphysics modelling of the piezoelectric generation in zinc oxyde nanowiresGraton, Olivier 03 October 2012 (has links)
Les progrès réalisés dans les processus de fabrication ont mené vers un contrôle accru des dimensions et de la composition chimique des nanostructures, permettant l’émergence de nouveaux dispositifs appelés Nanosystèmes ElectroMécaniques ou NEMS. Outre leurs propriétés physiques originales, leurs dimensions réduites leurs confèrent un fonctionnement peu coûteux en énergie Ainsi, l’utilisation de l’environnement de tels dispositifs comme source d’énergie est possible. Afin de préserver les avantages liés aux dimensions des NEMS, le système de récupération d’énergie doit présenter un volume réduit. Dans ce contexte, nous étudions les nanoffis de ZnO comme éléments actifs de micro et nanosystèmes de récupération d’énergie à travers deux modèles physiques de nanofils. L’originalité de ces deux modèles vient de la prise en compte du couplage entre les propriétés piezoélectriques et les propriétés semiconductrices du ZnO et de ses effets dans la conversion électromécanique de l’énergie. / Recent progresses in manufacturing processes allow a better control of dimensions and chemical composition of nanostructures, This leads to the emergence of a new family of devices known as Nano ElectroMechanical Systems or NEMS. These devices show novel physical properties and functional characteristics due to their reduced size. Besides, their operating power consumption are tiny, making the use of their environment as energy source highly attractive. The design of a generator that scavenge the surrounding energy of the NEMS is quite a challenge; indeed, such a microharvester should be small enough to ensure that the dimensions of the whole autonomous device are still acceptable. in that context, we investigate ZnO nanowires as active elements of piezoelectric nano and microgenerator. We have specially developed two models of nanowire that take into account of the piezoelectric-semiconducting coupling to appreciate its effects on the electromechanical conversion of energy.
|
470 |
Récupération d’énergie mécanique pour vêtements connectés autonomes / Human mechanical energy harvesting systems for smart clothesGeisler, Matthias 30 November 2017 (has links)
La fonctionnalisation « intelligente » des vêtements et accessoires portés par la personne est un phénomène à croissance rapide. L’installation des smartphones dans le quotidien des personnes en une décennie à peine en témoigne. L’autonomie énergétique de ces systèmes est un enjeu important, tant en termes d’ergonomie que de ressources : l’usage de piles ou batteries électrochimiques à l’échelle de milliards d’objets connectés est difficilement envisageable. La récupération d’énergie se pose en alternative pour complémenter ou remplacer ces unités de stockages. Cette thèse explore plusieurs approches pour utiliser l’énergie mécanique de la personne afin d’alimenter un vêtement intelligent en énergie électrique.Après avoir identifié le besoin énergétique d’un vêtement connecté typique, et comparé les possibilités des récupérateurs d’énergie de la littérature, trois formats de récupérateurs d’énergie sont étudiés. Le premier est un générateur inertiel à induction résonant non linéaire, de la taille d’une pile AA et permettant l’exploitation des impacts des pas de la personne. L’étude porte essentiellement sur la modélisation et l’optimisation du système pour l’activité humaine. Le prototype associé présente une densité de puissance supérieure à 500µW/cm3 lors de la course à pied. Le second récupérateur étudié est aussi un générateur inertiel à induction. D’une forme « toroïdale », il exploite le balancier des membres de la personne, et est capable de produire des puissances supérieures au milliwatt lorsqu’il est fixé au niveau du pied ou du bras. Enfin, le troisième concept de récupérateur d’énergie proposé s’appuie sur la transduction électrostatique à capacité variable pour exploiter des déformations dans les vêtements. Le système associe la triboélectricité avec un circuit d’auto-polarisation passif, le doubleur de Bennet. Cette combinaison permet de polariser une capacité variable de façon importante, sans source de tension externe, et ainsi de maximiser l’énergie électrostatique générée. Le dispositif réalisé pour faire la preuve du concept produit ainsi plus de 150µJ par cycle. Cette architecture électrostatique ouvre d’intéressantes possibilités en matière d’ergonomie et d’intégration dans les vêtements. En effet, elle laisse entrevoir le développement de structures étirables et flexibles s’adaptant bien aux contraintes de cette application.La comparaison de ces trois approches est instructive quant aux perspectives de développement du domaine de la conversion de l’énergie mécanique de la personne. / The functionalization of common objects in the human’s environment with electronics is a fast-growing trend, as demonstrated by the emblematic example of smartphones which became almost essential in the everyday life in less than a decade. One important stake of these systems is their power supply, in terms of ergonomics as well as resources: the use of electromechanical batteries to fuel billions of connected “things” is not the most attractive prospect. Energy harvesting techniques may provide an alternative or a complement to the use of these storage units. This thesis explores different structures of generators to efficiently convert the user’s mechanical energy to ensure the electrical self-sufficiency of smart wearables.Based on power requirement considerations for a typical “smart shirt” and comparing human energy harvesters from the literature, different structures are investigated. The first one is an inertial electromagnetic generator, the size of an AA-battery, designed to convert footsteps impacts. A thoroughly modelled and optimized device is able to generate power densities over 500µW/cm3 while attached on the arm during a run. The second considered energy harvester format is a “looped” inertial structure which is adapted to exploit the swing-type motions of the user’s limbs. This system is able to produce milliwatts-level powers from the motion of a small magnetic ball inside the device. Finally, a third generator concept that relies on electrostatic induction was developed, which uses variable capacitance structures to turn clothes deformations into electricity. The architecture of this energy harvester combines the triboelectric effect with a circuit of built-up self-polarization, Bennet’s doubler. It enables high levels of bias voltages without the need of an external source, and thus to maximize the energy generated per electrostatic cycle. A simple test device is shown to produce over 150µJ per cycle. This approach is promising in terms of integration in smart clothing, because it enables the development of flexible and stretchable devices well complying with the comfort requirements of worn systems.The comparison of those three energy harvesters provides an interesting basis for the future developments of energy harvesters converting one’s mechanical energy.
|
Page generated in 0.0546 seconds