For over half a century, the technological promise of spins manipulable by a small voltage has captivated the interest of experimental and theoretical researchers alike. However, if thin-film multiferroics are to be incorporated into future data storage devices, a much greater understanding of their behaviour and how they differ from their bulk counterparts is required. In this thesis, we probe the fundamental multiferroic properties of BiFeO₃ films through a combination of state-of-the-art diffraction and microscopy techniques. We investigate the coupling between magnetic, ferroelectric, and structural order, with a focus on domains, and how the domain structure may be manipulated in order to tailor the multiferroic properties of the material. Using non-resonant magnetic x-ray scattering (NXMS) and neutron diffraction, we study the magnetic and structural properties of (111)_pc-oriented BiFeO₃ films. Contrary to the general belief that to they grow as a rhombohedral monodomain, we find that they comprise a sub-micron texture of monoclinic domains. The magnetic structure is found to be intimately coupled to the structure, resulting in the propagation vector being locked to the monoclinic b-axis. This magnetoelastic coupling opens up a route to strain-engineer the magnetic domains via epitaxial strain. By growing BiFeO₃ films on a lower-symmetry, TbScO₃ substrate, we are able to engineer a magnetic, structural and ferroelectric monodomain, coherent over the entire film, constituting an increase in the domain size by over five orders of magnitude. We directly demonstrate the coupling between ferroelectric and magnetic order parameters of the cycloidal magnetic structure. Using NXMS polarimetry to measure directly the magnetic polarity, we show that upon switching the ferroelectric polarisation, the magnetic polarity switches accordingly---a major rearrangement of the magnetic structure, with each spin rotating by 90 degrees on average. This goes counter to idea that magnetic and ferroelectric order parameters are only weakly coupled in type-I multiferroics. Finally, using photoemission electron microscopy we are able to directly image the sub-micron magnetostructural domain structure. We further show that there is a strong interfacial coupling between the magnetostructural domains of BiFeO₃ with a ferromagnetic overlayer. The BiFeO₃ domains are found to impose a uniaxial anisotropy in the overlayer, opening up a route to control ferromagnetic domains.

Made available in DSpace on 2016-06-02T20:16:54Z (GMT). No. of bitstreams: 1 6698.pdf: 13275782 bytes, checksum: 2c4bbd5a5c838552f7cbf82ce709e116 (MD5) Previous issue date: 2015-03-09 / Financiadora de Estudos e Projetos / In this work, the lead-free ceramic powders of xBi0,5Na0,5TiO3 - (0,7186 - 0,7143x) Bi0,5K0,5TiO3 - (2814 - 2857x) BaTiO with x = 0,8200; 0,8625; 0,8792, 0,9126 and 0,9300 (BNBK1000x) were prepared by the solid state reaction method, followed by conventional densification. The ceramic bodies showed high density, which was higher than 95% in obtained samples. For the all ceramics were performed structural, micro structural, electric and anelastic characterizations. The X-ray diffraction (XRD) analysis indicated the formation of the complex perovskite type crystaline structure for all compositions analyzed without the presence of spurious phases. By the structural refinement by the Rietveld method of XRD data and by Raman spectroscopy were observed that for BNBK912 and BNBK930 compositions, at room temperature, the predominant symmetry is rhombohedral (R3c), while the BNBK820 composition exhibits a tetragonal crystalline symmetry (P4mm). For the BNBK879 and BNBK826 compositions presented a mixture of phases, possibly with rhombohedral and tetragonal symmetry, reaveling the morphotropic phase boundary (MPB) of this system. The microstructure of BNBK1000x ceramics was investigated by scanning electron microscopy (SEM), where the morphology grains with irregular sizes and shapes, where the increased levels of K+ and Ba2+ ions suppressed the growth of the grains. The characterizations by Raman spectroscopy at room temperature showed broad Raman modes, due to the chemical and/or structural disorder related to the substitution of elements Bi and Na for Ba and K. The ferroelectric characterizations at room temperature of the BNBK1000x ceramics showed that all compositions studied are ferroelectric. Through the comparison among the measurements of electrical impedance and mechanical spectroscopy, was possible to identify the different structural and electric phase transitions that were employed in the construction of a pseudodiagram of phases for the BNBK1000x compositions. / Neste trabalho, os pós-cerâmicos livres de chumbo xBi0,5Na0,5TiO3 - (0,7186 - 0,7143x) Bi0,5K0,5TiO3 - (2814 - 2857x) BaTiO com x = 0,8200; 0,8625; 0,8792, 0,9126 e 0,9300 (BNBK1000x) foram obtidos através do método de reação de estado sólido, seguido por densificação convencional. Os corpos cerâmicos obtidos apresentaram elevada densificação, sendo maior que 95% nas amostras produzidas. Para todas as cerâmicas foram realizadas caracterizações estruturais, microestruturais, elétricas e anelásticas. As análises por difração de raios-X (DRX) indicaram a formação da estrutura cristalina tipo perovkista complexa para todas as composições analisadas, sem a presença de fases espúrias. O refinamento estrutural, pelo método de Rietveld, dos resultados de DRX e os resultados de espectroscopia Raman apontam que para as composições BNBK930 e BNBK912 a simetria predominante em temperatura ambiente é romboédrica (R3c), enquanto que a composição BNBK820 apresenta a simetria cristalina tetragonal (P4mm). Já as composições BNBK879 e BNBK862 apresentaram uma mistura de fases, possivelmente com simetrias romboédrica e tetragonal, evidenciando o contorno de fase morfotrópico (CFM) deste sistema. A microestrutura das cerâmicas de BNBK1000x foi investigada por microscopia eletrônica de varredura (MEV), onde a morfologia apresentada pelas diferentes composições estudadas possuíam grãos com tamanhos e formatos irregulares, sendo que o aumento dos teores dos íons de K+ e Ba2+ inibiram o crescimento dos grãos. A caracterização por espectroscopia Raman, em temperatura ambiente, apresentou modos Raman amplos, mostrando um elevado grau de desordem química e/ou estrutural devido à substituição dos elementos Bi e Na por Ba e K. As caracterizações ferroelétricas, também em temperatura ambiente das cerâmicas de BNBK1000x mostraram que todas as composições estudadas possuem propriedades ferroelétricas. Através da comparação entre as medidas de impedância elétrica e anelástica, levando em consideração as caracterizações estruturais e ferroelétricas com temperatura, foi possível identificar diferentes transições de fase estruturais e elétricas, que foram empregadas na construção de um pseudo-diagrama de fases para as composições de BNBKx.

In this work, in-depth structural and electrical characterisation is used to study a family of “empty” tetragonal tungsten bronzes (TTBs), A2₄A1₂B1₂B2₈O₃₀. An initial investigation into the effect of the A1-cation size on the properties of empty Ba₄R₀.₆₇◻₁.₃₃Nb₁₀O₃₀ TTBs (where R is the A1-cation and R = La, Nd, Sm, Gd, Dy and Y; ◻ = vacancy) was performed. These were determined to be metrically tetragonal by powder x-ray diffraction, with decreasing R cation size inducing increased crystal anisotropy. This tetragonal structural distortion, driven by contraction in the ab-plane, is shown to stabilise c-axis ferroelectricity; a direct correlation between tetragonality and the ferroelectric Curie temperature, T[sub]C, is demonstrated. Further examination of the relaxor ferroelectric (RFE) to ferroelectric (FE) crossover in Ba₄(La₁₋ₓNdₓ)₀.₆₇◻₁.₃₃Nb₁₀O₃₀ TTBs using detailed structural studies employing variable temperature, high resolution neutron, synchrotron X-ray and electron diffraction revealed a common superstructure with 2√2 × √2 × 2 cell with respect to the basic tetragonal aristotype cell. However, they display different degrees of order/disorder which can disrupt polar order (ferroelectricity). La-rich analogues exhibit a disordered regime between the low and high temperature ferroelectric and non-polar phases. Although polar, this disordered regime is non-ferroelectric, however, large polarisation may be established with an applied electric field, but relaxes back to the disordered phase upon removal of the field. Substitution of Nd for La at the A1-site leads to destabilisation of the disordered phase and reintroduces “normal” ferroelectric behaviour. Finally, isovalent substitution of Sr²⁺∙ for Ba²⁺ is shown to lead to the development of relaxor behaviour at higher dopant concentrations in Ba₄₋ₓSrₓDy₀.₆₇◻₁.₃₃Nb₁₀O₃₀, (x = 0, 0.25, 0.5, 1, 2, 3; ◻ = vacancy). With increasing x the unit cell contracts in both the ab- plane and c-axis coinciding with a decrease in T[sub]C and development of relaxor behaviour for x ≥ 2. This observation is rationalised by differing cation occupancies: for x ≤ 1, Sr²⁺ principally occupies the A2-site while for x ≥ 2 significant Sr²⁺ occupation of the A1-site leads to the observed RFE characteristics. The FE to RFE crossover is discussed in the context of a previously proposed TTB crystal chemical framework with the A1-site tolerance factor identified as the dominant influence on relaxor behaviour.

In this thesis, the physical properties of certain multi-functional organic crystals were studied in detail. This study involves the growth of single crystals of Glucuronic acidγ-lactone (GAL), Imidazoliumtartarate (IMLT), (Bis)imidazoliumtartarate (BIMLT), and Diisopropylammonium iodide (DPI) and investigations of their optical, dielectric, piezoelectric, pyroelectric, and ferroelectric properties as a function of temperature and dependence on crystal structure in these organic crystals. Piezoelectric resonance was observed at certain frequencies when dielectric constant was monitored along the b-plate of GAL crystals. The electro-mechanical coupling coefficient estimated at the resonance near 1 MHz frequency revealed an exceptionally large value in GAL similar to that in inorganic lead titanate. The dependence of the piezoelectric resonance frequency on temperature was studied in detail. These crystals showed excellent second- and third-order nonlinear optical properties as well as high laser damage threshold. The high values of χ(2) andχ(3), laser damage threshold, and low UV cut-off makes GAL crystals an interesting prospect for NLO and laser applications. Towards this goal, GAL crystals were studied in detail with regard to determination of directions of dielectric axes, optic axes, and collinear phase-matching. Single crystals of another promising NLO organic crystal, IMLT were also grown which showed interesting dielectric, piezoelectric, and NLO properties. The dielectric dispersion with temperature provided an insight to the polarization mechanisms. Like GAL, IMLT also exhibits piezoelectric resonance. The existence of only one easy axis of vibration in IMLT enabled the candidate to identify the first resonance peak as corresponding to the fundamental mode of oscillation in the sample. This also helped to determine many piezoelectric parameters. By angular phase matching, one direction of phase matching in IMLT was identified. The conversion efficiency of IMLT along this direction was determined which was high in comparison to that in a standard KDP crystal. At piezoelectric resonance frequencies, the electro-optic response due to photo-elastic contributions is enhanced. Single crystals of organic ferroelectric BIMLT were grown by mixing two moles of imidazole with one mole of l-tartaric acid. The controversy with regard to the phase transition temperature of BIMLT was clarified by the DSC and structural analysis in this work. Previously, studies on BIMLT were limited to polycrystalline samples and single crystals with inclusions primarily due to the difficulty in growing good quality single crystals from aqueous solution. However, by experimenting the growth process using different solvents, good quality single crystals were achieved without the trapping of mother solution. This remarkable find is a notable result in these crystals for ferroelectric applications. The mechanism of ferroelectricity in BIMLT is mainly attributed to the transfer of protons along N–H---O hydrogen bonds in the direction of b-axis. Interestingly, the values of spontaneous polarization and Curie-temperature in the organic ferroelectric material DPI were significantly high and comparable to several popular inorganic ferroelectrics. The polarization obtained in this material is the highest among reported organic ferroelectrics. In addition to the high Curie temperature and spontaneous polarization, there were unique phase transitions that were revealed in DPI. The mechanism of ferroelectricity is quite complex, mainly being displacive type on account of the change in orientation of dipoles with electric field. Some contribution to ferroelectricity comes from the order-disorder nature of Nitrogen atom.

Non-centrosymmetric materials that can be polarized under applied mechanical stress or electric field are piezoelectric in nature and the phenomenon is called piezoelectric effect. They are broadly classified as direct and converse piezoelectric effects. Piezo-ceramics have a wide range of applications such as piezoelectric actuators, sensors, and transducers. Among piezoceramics, ferroelectric based materials are imperative owing to the existence of spontaneous polarization in these systems. Several materials are investigated starting from naturally occurring crystals to synthetic ceramics but are limited in their application range. The piezoelectric and ferroelectrics properties of the solid-solutions based on lead zirconate and lead titanate called lead zirconate titanate (PZT), lead magnesium niobate-lead titanate (PMN-PT), lead zinc niobate-lead titanate (PZN-PT) (near morphotrophic phase boundary (MPB)) demonstrate their potential for myriad device applications besides inciting a great deal of academic interest. They have been widely used for commercial applications such as ultra sound transducers, ultrasonic motors, fuel injector actuators, nano positioners in scanning electron microscope etc. However, these materials contain more than 60% lead by weight and volatization of Pb at higher temperature, and disposal of lead results in environmental pollution and are fatal to human health. This gave an insight to search for lead-free solid solutions covering a wide spectrum of applications akin to that of PZT. The search for alternatives to lead based piezoelectric materials is now being focused on modified barium titanates and alkali niobates in which the incidence of MPB was reported similar to that of PZT. In this thesis the results pertaining to the various investigations carried out on modified barium titanates, Ba(Zr0.2Ti0.8)O3- x(Ba0.7Ca0.3)TiO3(BCZT), and alkali niobates, potassium sodium niobate (KNN), are presented. Especially, lead-free piezoelectric material Ba(Zr0.2Ti0.8)O3-x(Ba0.7Ca0.3)TiO3(BCZT) with x= 0.5 has attracted great attention due to its excellent piezoelectric properties. Contrary to the other Pb-free systems, the BZT–BCT phase diagram shows a Morphotropic Phase Boundary (MPB) characterized by the existence of a tri-critical point (TCP), which is also the case for PZT and PMN–PT. One drawback of the BZT–xBCT (x=0.5) is its high sintering temperature (where it exhibits the largest d33 of 550 – 620pC/N). Several methods have been adopted and various additives are being added to bring down the sintering temperature, since high d33 requires an optimized sintering temperature of around 1540oC which also shows excellent ferroelectric properties. However, the methods that were reported in the literature to synthesize the above materials do not guarantee compositional homogeneity and also there is a limitation in obtaining ceramics of enhanced grain size as the ceramics comprising larger grains are demonstrated to exhibit high piezoelectric coefficients. Therefore to address these issues, the simple soft chemical route was adopted to synthesize chemically homogenous powder and the influence of microstructure (grain size) and ferroelectric domains on piezoelectric properties of the BCZT at nano and micron sized crystallites was studied. The results obtained are classified into chapter 3 and chapter 4 accordingly apart from introduction, materials, and methods. Another challenging area of research in lead free piezoceramics for nanoscale device application is to synthesize materials and to visualize the piezoelectric properties at nanoscale with controlled shapes and sizes. For that, Mg2+ ion was chosen as the dopant especially on Ba2+ sites to synthesize Ba0.95Mg0.05Zr0.1Ti0.9O3 (BMZT) nanocrystals, as MgO is known to be an effective grain growth inhibitor in many functional and structural ceramics. Therefore in the present thesis Mg2+ ion was chosen to exercise a strict control over the grain size. The results obtained from this title compound are discussed in chapter 5. Another class of material is K0.5Na0.5NbO3 (KNN), which has been considered a good candidate for lead-free piezoelectric materials. KNN exhibits an MPB around 50% K and 50% Na separating two orthorhombic phases from the complete solid solution of NaNbO3 (Anti-ferroelectric) and KNbO3 (ferroelectric). The major problem associated with KNN ceramic is its complex densification process; difficulty in processing and volatilization of sodium at higher sintering temperature leading to stoichiometric discrepancy. To overcome these difficulties, in the present investigations, an attempt has been made to fabricate KNN ceramics by employing the liquid phase sintering method. In this chapter, B2O3 and borate based glass (0.5 Li2O - 0.5K2O- 2B2O3) were chosen to improve the densification, grain size and their effects on the physical properties of the KNN ceramics are discussed in chapter 6. In chapter 7, KNN crystallites (with size varying from nano to micrometers) were dispersed in the Polyvinylidene fluoride (PVDF) matrix to obtain a polymer/nano or micro crystal composites and the effect of nano and micron sized KNN fillers on the structural, dielectric and piezoelectric properties were investigated. The results obtained pertaining to these aforementioned investigations are organized as follows. In Chapter 1, a brief introduction to the field of ferroelectricity, piezoelectricity, and piezoelectric materials. The emphasis has been on the ferroelectric based piezoelectric materials belonging to the perovskite family of oxides. A brief exposure to the conventional lead based piezoceramics, lead zirconate titanate (PZT) is discussed. Furthermore, drawbacks associated with lead based ceramics are highlighted and alternatives to PZT based ceramics such as modified barium titanate and alkali niobate solid solutions are focused, leading to the motivation and objectives of our work. Chapter 2 describes the various experimental techniques that are employed to synthesize and characterize the materials under investigation. Chapter 3 deals with details concerning the characterization of Ba0.85Ca0.15Zr0.1Ti0.9O3 (BCZT) nanocrystals prepared via complex oxalate precursor route at a relatively low temperature (800°C/5h). The phase formation temperature of BCZT at nanoscale was confirmed by thermogravimetric (TG), differential thermal analysis (DTA) followed by X-ray powder diffraction (XRD) studies. Fourier Transform Infrared (FTIR) spectroscopy was carried out to confirm the complete decomposition of oxalate precursor into BCZT phase. The XRD and profile fitting revealed the coexistence of cubic and tetragonal phases and was also corroborated by Raman study. Transmission electron microscopy (TEM) studies carried out at 800°C and 1000°C/5h heat treated BCZT powder revealed the crystallite size to be in the range of 20 – 50 nm and 40 – 200 nm respectively. The optical band gap for BCZT nanocrystalline powder was obtained using Kubelka Munk function and was found to be around 3.12 ± 0.02 eV and 3.03± 0.02 eV respectively for 800°C (20 – 50 nm) and 1000°C/5h (40 – 200 nm) heat treated samples. The piezoelectric properties were studied for two different crystallite sizes (30 and 70 nm) using piezoresponse force microscope (PFM). The d33 coefficients obtained for 30 nm and 70 nm sized crystallites were 4 pm/V and 47 pm/V respectively. These were superior to those of BaTiO3 nanocrystal (≈ 50 nm) and promising from the technological/industrial applications perspective. Chapter 4 deals with the studies concerning the effect of microstructure (Grain size) and ferroelectric domains on physical properties of Ba0.85Ca0.15Zr0.1Ti0.9O3 ceramics. Fine powders comprising nanocrystallites of Ba0.85Ca0.15Zr0.1Ti0.9O3 (BCZT) were synthesized via oxalate precursor method which facilitated to obtain homogenous and large grain sized ceramics at a lower sintering temperature. The compacted powders were sintered at various temperatures in the range of 1200°C - 1500°C for an optimized duration of 10h. Interestingly the one that was sintered at 1450°C/10h exhibited well resolved Morphotrophic Phase Boundary (MPB). The average grain size associated with this sample was 30 µm accompanied by higher domain density mostly with 90° twinning. These were believed to make a significant contribution towards obtaining large strain of about 0.2 % and piezoelectric coefficient as high as 563 pC/N. The maximum force that was generated by BCZT ceramic (having 30 µm grain size) was found to be 161 MPa which is much higher than that of known actuator materials such as PZT (40 MPa) and NKN-5-LT (7 MPa). Chapter 5 reports the details involving the synthesis, structural, optical, and piezoelectric response of lead free Ba0.95Mg0.05Zr0.1Ti0.9O3 nanocrystalline powder. Nanocrystalline powders of Ba1-xMgxZr0.1Ti0.9O3 (x=0.025 - 0.1) were synthesized via citrate assisted sol-gel method. Interestingly, the one with x=0.05 in the system Ba1-xMgxZr0.1Ti0.9O3 exhibited fairly good piezoelectric response apart from the other physical properties. The phase and structural confirmation of synthesized powder was established by X-ray powder diffraction (XRD) and Raman Spectroscopic techniques. Two distinct Raman bands i.e., 303 cm-1 and 723 cm-1 characteristic of the tetragonal phase were observed. Thermogravimetric analysis (TGA) was performed to evaluate the phase decomposition of the as-synthesized Ba0.95Mg0.05Zr0.1Ti0.9O3 sample as a function of temperature. The average crystallite size associated with Ba0.95Mg0.05Zr0.1Ti0.9O3 was calculated using Scherrer formula based on the XRD data and was found to be 25 nm. However, Scanning and Transmission Electron Microscopy studies revealed the average crystallite size to be in the range of 30-40 nm. Kubelka-Munk function was employed to determine the optical band gap of these nanocrystallites. The piezoelectric response of 26 pm/V was observed for Ba0.95Mg0.05Zr0.1Ti0.9O3 nanocrystal by Piezoresponse Force Microscopy (PFM) technique. Photoluminescence (PL) study carried out on these nanocrystals exhibited a blue emission (470 nm) at room temperature. Chapter 6 describes the effect of the addition of B2O3 on the density, microstructure, dielectric, piezoelectric and ferroelectric properties of K0.5Na0.5NbO3 ceramics. Boron oxide (B2O3) addition to pre-reacted K0.5Na0.5NbO3 (KNN) powders facilitated swift densification at relatively low sintering temperatures which was believed to be a key to minimize potassium and sodium loss. The base KNN powder was synthesized via solid-state reaction route. The different amounts (0.1 to 1 wt %) of B2O3 were added, and ceramics were sintered at different temperatures and durations to optimize the amount of B2O3 needed to obtain KNN pellets with the highest possible density and grain size. The 0.1 wt% B2O3 added KNN ceramics sintered at 1100°C for 7h exhibited higher density (98%) with grain size of ~5 µm. Scanning electron microscopy (SEM) studies confirmed an increase in average grain size with increasing B2O3 content at the appropriate temperature of sintering and duration. The B2O3 added KNN ceramics exhibited improved dielectric and piezoelectric properties at room temperature. For instance, 0.1 wt% B2O3 added KNN ceramic exhibited d33 value of 116 pC/N which is much higher than that of pure KNN ceramics. Interestingly, all the B2O3 added (0.1 to 1wt %) KNN ceramics exhibited polarization – electric field (P vs E) hysteresis loops at room temperature. The remnant polarization (Pr) and coercive field (Ec) values are dependent on the B2O3 content and crystallite size. The details pertaining to the effect of the addition of borate based glass (0.5 Li2O - 0.5K2O- 2B2O3) on the physical properties of K0.5Na0.5NbO3 ceramics are also reported in this chapter. The addition of powdered 0.5 Li2O - 0.5K2O- 2B2O3 (LKBO) glass (0.5 to 2 wt%) to potassium sodium niobate, K0.5Na0.5NbO3 (KNN) powder facilitated higher densification which resulted in improved physical properties that include dielectric, piezoelectric and ferroelectric. The required polycrystalline powders of KNN were synthesized through solid-state reaction route, while LKBO glass was obtained via the conventional melt-quenching technique. Pulverized glass was added to KNN powders in different wt% and compacted at room temperature and these were sintered around 1100°C. Indeed the addition of optimum amount (1 wt %) of LKBO glass to KNN ceramics facilitated lowering of sintering temperature accompanied by larger grains (8 µm) with improved density. The dielectric constant (εr) measured at room temperature was 475 (at 10 kHz), whereas it was only 199 for the LKBO glass free KNN. The piezoelectric coefficient (d33) was found to be 130 pC/N for 1wt% LKBO added glass, which was much higher than that of pure KNN ceramics (85 pC/N). Indeed, the LKBO glass added samples did exhibit well saturated P versus E hysteresis loops at room temperature. Though there was no particular trend observed in the variation of Pr with the increase in glass content, the Pr values were higher than those obtained for KNN ceramics. The improved physical properties of KNN ceramics encountered in these studies were primarily attributed to enhancement in density and grain size. Chapter 7 presents a comparative study on the structural, dielectric and piezoelectric properties of nano and micron sized K0.5Na0.5NbO3 fillers in PVDF composites. Polymer nanocrystal composites were fabricated by embedding polyvinylidene fluoride (PVDF) with different vol% of K0.5Na0.5NbO3 (KNN) nanocrystallites using hot-pressing technique. For comparison, PVDF-KNN microcrystal composites of the same compositions were also fabricated which facilitated the crystallite size (wide range) effect studies on the dielectric and piezoelectric properties. The structural, morphological, dielectric, and piezoelectric properties of these nano and micro crystal composites were investigated. The incorporation of KNN fillers in PVDF at both nano and micrometer scale above 10vol% resulted in the formation of polar β-form of PVDF. The room temperature dielectric constant as high as 3273 at 100Hz was obtained for PVDF comprising 40 vol% KNN nanocrystallites due to dipole –dipole interactions (as the presence of β-PVDF is prominent), whereas it was only 236 for PVDF containing the same amount (40 vol%) of micron sized crystallites of KNN at the same frequency. Various theoretical models were employed to predict the dielectric constants of the PVDF-KNN nano and microcrystal composites. PVDF comprising 70 vol% micronmeter sized crystallites of KNN exhibited d33 value of 35pC/N, while the nanocrystal composites of PVDF-KNN did not exhibit any piezoelectric response perhaps due to unrelieved internal stress within each grain besides having less number of domain walls. The Thesis ends with summary and conclusions, though each chapter is provided with conclusions and a complete list of references.

Fundação de Apoio a Pesquisa e à Inovação Tecnológica do Estado de Sergipe - FAPITEC/SE / The RMnO3 (R=Y,Lu) compounds, members of the family of hexagonal manganites, are materials which exhibit strong magneto-electric coupling characteristic for multiferroic compounds. Despite the numerous studies with objective to reveal the origin of this phenomenon, the mechanism that is causing it is still not fully understood. The question that attracts special attention of scientific community is about the cause of ferroelectric distortion that occurs at certain temperatures in these materials. Although this issue is discussed in many papers, there is still no consensus what mechanism is responsible for it: (1) hybridization between the Mn dz2 orbital and O pz orbital (Mn d0 –ness model), (2) hybridization between the R dz2 orbital and O pz orbital (R d0 –ness model), (3) geometric effects or (4) charge transfer from Mn-O bonds to R-O bonds. Understanding of the mechanism that leads to ferroelectric polarization is necessary to speed application of these materials in ferroelectric memories or spintronics devices. Objective of the present work was to evaluate the first two possible mechanisms that might cause the ferroelectric distortion in RMnO3. Adopted strategy was to investigate what happens with the Mn-O and R-O chemical bonds after the structural phase transition from paraelectric to ferroelectric phase that occurs at high temperature, at which both phases are characterized by paramagnetic order of the Mn magnetic moments. For that purpose, the first-principles calculations based on density functional theory were carried on, with usage of the most modern exchange-correlation potentials. The chemical bonds were evaluated (1) qualitatively, by analysis of density of electronic states (DOS) and maps of electronic density along the bonds, and (2) quantitatively, in terms of topological analysis of Bader. The results revealed that no significant change occurred with Mn-O bonds, while the R-O bonds were affected by phase transition in the sense that R dz2 and O pz orbital exhibited enhanced hybridization in the ferroelectric phase. Therefore, the present study substantiates the R d0 –ness mechanism as the probable cause of ferroelectric distortions in RMnO3 compounds. / The RMnO3 (R=Y,Lu) compounds, members of the family of hexagonal manganites, are materials which exhibit strong magneto-electric coupling characteristic for multiferroic compounds. Despite the numerous studies with objective to reveal the origin of this phenomenon, the mechanism that is causing it is still not fully understood. The question that attracts special attention of scientific community is about the cause of ferroelectric distortion that occurs at certain temperatures in these materials. Although this issue is discussed in many papers, there is still no consensus what mechanism is responsible for it: (1) hybridization between the Mn dz2 orbital and O pz orbital (Mn d0 –ness model), (2) hybridization between the R dz2 orbital and O pz orbital (R d0 –ness model), (3) geometric effects or (4) charge transfer from Mn-O bonds to R-O bonds. Understanding of the mechanism that leads to ferroelectric polarization is necessary to speed application of these materials in ferroelectric memories or spintronics devices. Objective of the present work was to evaluate the first two possible mechanisms that might cause the ferroelectric distortion in RMnO3. Adopted strategy was to investigate what happens with the Mn-O and R-O chemical bonds after the structural phase transition from paraelectric to ferroelectric phase that occurs at high temperature, at which both phases are characterized by paramagnetic order of the Mn magnetic moments. For that purpose, the first-principles calculations based on density functional theory were carried on, with usage of the most modern exchange-correlation potentials. The chemical bonds were evaluated (1) qualitatively, by analysis of density of electronic states (DOS) and maps of electronic density along the bonds, and (2) quantitatively, in terms of topological analysis of Bader. The results revealed that no significant change occurred with Mn-O bonds, while the R-O bonds were affected by phase transition in the sense that R dz2 and O pz orbital exhibited enhanced hybridization in the ferroelectric phase. Therefore, the present study substantiates the R d0 –ness mechanism as the probable cause of ferroelectric distortions in RMnO3 compounds.

In recent years bismuth-based, layer-structured perovskites such as SrBi2Nb2O9 (SBN) and SrBi2Ta2O9 (SBT) have been investigated extensively, because of their potential use in ferroelectric random access memories (FeRAMs). In comparison with non-layered perovskite ferroelectrics such as Pb(Zr,Ti)O3 (PZT), these offer several advantages such as fatigue free, lead free, low operating voltages and most importantly their ferroelectric properties are independent of film thickness in the 90 to 500 nm range. For FeRAM device applications, large remnant polarization (Pr), low coercive field (Ec) accompanied by high Curie temperature (Tc) are required for better performance and reliable operation. Much effort has been made to improve the ferroelectric properties of SBN and SBT ceramics by doping on A or B sites. It was known in the literature that partial substitution of Sr2+ by Bi3+ ions in SBN and SBT would increase the Curie temperature and improve the dielectric properties. The focus of the investigations that were taken up was to improve the electrical, dielectric and ferroelectric characteristics of SrBi2Nb2O9 ceramics. It was reported that the ferroelectric and nonlinear optical properties of LiNbO3 and LiTaO3 could be improved when vanadium, the lightest element in group V of the periodic table is substituted for Nb or Ta along with Li and three oxygens. It is with this background the investigations have been taken up to see whether one can extend the same argument to the Aurivillius family of oxides. Therefore, the central theme of the present investigations aimed at substituting Nb5+ by a smaller cation V5+ in SBN and study its influence on the formation temperature, sinterability, structural and microstructural characteristics apart from its physical properties. Recently the optical properties of this material have been recognized to be important from the optical device point of view. Unfortunately single crystal growth of vanadium doped SBN was hampered because of the bismuth and vanadium loss (high volatility) observed in the process of growth. One of the routes that attracted our attention has been the glass-ceramic. It would be interesting to visualize the behavior of crystallites of nano/micrometer size embedded in a glass matrix as these crystals were known to give rise to exotic properties. One of the crucial steps in the process of fabrication of a glass nanocrystalcomposite system in which crystalline phases have symmetries that would eventually give rise to basic non - centrosymmetric properties such as piezoelectric, pyroelectric and Pockels effects, has been to choose a compatible matrix material associated with easy glass forming capability and the ability to evenly disperse dipolar defects within itself. Recent investigations into strontium borate SrB4O7 (SBO), lithium borate Li2B4O7 (LBO) glasses indicated that LBO by virtue of its favorable structure, thermal and optical properties would form a suitable host glass matrix for dispersing layer structured ferroelectric oxides belonging to the Aurivillius family of oxides. Since lithium borate has wide transmission window, it was worth making an attempt to fabricate optical composite of Li2B4O7 (LBO) and vanadium doped SrBi2Nb2O9 (SBVN) and to study its structural, dielectric, pyroelectric, ferroelectric and optical properties. Therefore the present thesis reports detailed investigations into the effect of vanadium doping on the structural and various physical properties of an n = 2 member of the Aurivillius family of oxides in the polycrystalline form and novel glass composites comprising nano/microcrystallites of this phase. Chapter 1 comprises a brief introduction to the dielectric, pyroelectric, ferroelectric and nonlinear optical properties of materials. In addition to the principles and phenomena, the material aspects of these important branches of physics are discussed. It also forms a preamble to the glasses, criteria for glass formation, glass – ceramics and subsequently ferroelectric and nonlinear optical effects that were observed in glasses and glass - ceramics. Chapter 2 describes the material fabrication techniques adopted to prepare polycrystalline and grain – oriented ceramics, glasses and glass nanocrystalcomposites. The details of various structural, dielectric, pyroelectric, ferroelectric and optical measurement techniques employed to characterize these materials are also included. Chapter 3 discloses the fabrication of strontium bismuth niobate ceramics and their characterization for dielectric and impedance properties. The dielectric properties of strontium bismuth niobate ceramics have been modeled based on Jonscher’s Universal formalism. The coefficients of the Jonscher’s expression, exponent n(T) undergoes a minimum and A(T) exhibits a peak at the Curie temperature, Tc (723K). A strong low frequency dielectric dispersion (LFDD) associated with an impedance relaxation has been found to exist in these ceramics in the temperature range 573 - 823K. The Z′′ of the AC complex impedance showed two distinct slopes in the frequency range 100Hz-1MHz suggesting the existence of two dispersion mechanisms. The exponents m and n were obtained from the curve fitting. The exponent n was found to exhibit a minimum at the Curie temperature, Tc (723K) whereas the m was temperature independent. Chapter 4 deals with the fabrication of vanadium doped SrBi2Nb2O9 ceramics and their characterization for microstructural, dielectric, pyroelectric and ferroelectric properties. The average grain size of the SrBi2Nb2O9 (SBN) ceramic containing V2O5 was found to increase with increase in V2O5 content. The dielectric constant (εr) as well as the dielectric loss (D) increased with increase in grain size (6µm-17µm). The pyroelectric coefficient was found to be positive at 300K and showed an increasing trend with increasing grain size. Interestingly, the SrBi2(Nb0.7V0.3)2O9-δ ceramics consisting of 17µm sized grains showed higher remnant polarization (Pr) and lower coercive field (Ec) than those with grains of 7µm. Chapter 5 deals with the dielectric properties which were studied in detail in the 100Hz to 1MHz frequency range at various temperatures (300 – 823 K) for undoped and vanadium (10 mol%) doped SrBi2Nb2O9 (SBVN10) ferroelectric ceramics. A strong low frequency dielectric dispersion was encountered in these ceramics in the 573 – 823 K temperature range. The dielectric constants measured in the wide frequency and temperature ranges for both the samples were found to fit well to the Jonscher’s dielectric dispersion relations. The dielectric behavior of SBN and SBVN10 ceramics was rationalized using the impedance and modulus data. The electrical conductivity studies of layered SrBi2(Nb1-xVx)2O9-δ ceramics with x lying in the range 0 to 0.3 (30 mol%) were centered in the 573 – 823K temperature range as the Curie temperature lies in this range. The concentration of mobile charge carriers (n), the diffusion constant (D0) and the mean free path (a) were calculated using Rice and Roth formalism. The conductivity parameters such as ion hopping rate (ωp) and the charge carrier concentration (K′) term have been calculated using Almond and West formalism. The afore mentioned microscopic parameters were found to be V2O5 content dependent in SrBi2(Nb1-xVx)2O9-δceramics. Chapter 6 describes the fabrication of partially grain – oriented SrBi2(Nb1-xVx)2O9-δ (0 ≤x≤3.0 in molar ratio) ceramics and characterization for their structural, microstructural, dielectric, pyroelectric and ferroelectric properties. The grain – orientation factor and the microstructural features were studied by XRD and scanning electron microscopy as a fuction of sintering temperature and V2O5 content. The dielectric constant measured along the direction parallel and perpendicular to the pressing axis has shown a significant anisotropy. The pyroelectric and ferroelectric properties were superior in the direction perpendicular to the pressing axis (polar) to that in the parallel direction. The fabrication and characterization details of (100 – x) (Li2B4O7) – x (SrO - Bi2O3 - 0.7 Nb2O5 – 0.3 V2O5) (10 ≤ x ≤ 60, in molar ratio) glasses and glass nanocrystal composites are dealt within Chapter 7. The nanocrystallization of strontium bismuth niobate doped with vanadium (SrBi2(Nb0.7V0.3)2O9-δ(SBVN)) has been demonstrated in Li2B4O7 glasses. The glassy nature of the as – quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as – quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X – ray powder diffraction studies. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat – treated at 783K/6h) confirm the presence of nano rods of SBVN embedded in Li2B4O7 glass matrix. Chapter 8 presents the physical properties of the glasses and glass nanocrystal composites. Dielectric constant of both the as – quenched and glass nanocrystal composites was found to increase with increase in the composition, whereas the loss was observed to decrease with increasing SBVN composition. Different dielectric mixture formulae were employed to analyze the dielectric properties of the glass nanocrystal composite. The electrical behaviour of the glasses and glass nanocrystal composites was rationalized using impedance spectroscopy. The observed pyroelectric response and ferroelectric hysteresis of these composites confirmed the polar nature. Various optical parameters such as optical band gap (Eopt), Urbach energy (∆E), refractive index (n), optical dielectric constant (ε′∞) and ratio of carrier concentration to the effective mass (N/m*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied. Transparent glasses embedded with nanocrystallites of SBVN exhibited intense second harmonic signals in transmission mode when exposed to IR laser light at λ = 1064 nm. The thesis ends with a summary of the important findings and conclusions.

Perovskite oxides have provided a wide variety of exotic functionalities based on their unique physical and chemical properties. By combining different perovskite oxides, interesting physical phenomena have been observed at the interfaces of perovskite heterostructures. The most interesting among these phenomena is the formation of two dimensional electron gas at the interface of two perovskite materials SrTiO3 and LaAlO3 which led to a number of fascinating physical properties such as metal-insulator transition, super-conductivity, large negative magnetoresistance and so on. This has raised the interest in exploiting the interface of various hybrids structures built on the perovskite oxide backbone. On the other hand, the two dimensional (2D) van der Waals materials such as graphene, MoS2, boron nitride etc. represent a new paradigm in the 2D electron-ics. The functionalities of these individual materials have been combined to obtain new enriched functionalities by stacking different materials together forming van der Waals heterostructures. In this work, we present a detailed study of the interface in hybrid structures made of vander Waals materials (graphene and MoS2) and their hybrids with a perovskite material namely, SrTiO3 which is known as the building block of complex oxide heterostructures. In graphene-MoS2 vertical heterostructure, we have carried out a detailed set of investigations on the modulation of the Schottky barrier at the graphene-MoS2 interface with varying external electric field. By using different stacking sequences and device structures, we obtained high mobility at large current on-off ratio at room temperature along with a tunable Schottky barrier which can be varied as high as ∼ 0.4 eV by applying electric field. We also explored the interface of graphene and SrTiO3 as well as MoS2 and SrTiO3 by electrical transport and low frequency 1/f noise measurements. We observed a hysteretic feature in the transfer characteristics of dual gated graphene and MoS2 field effect transistors on SrTiO3. The dual gated geometry enabled us to measure the effective capacitance of SrTiO3 interface which showed an enhancement indicating the possible existence of negative capacitance developed by the surface dipoles at the interface of SrTiO3 and the graphene or MoS2 channel. Our 1/f noise study and the analysis of higher order statistics of noise also support the possibility of electric field-driven reorient able surface dipoles at the interface.

Dans une première partie de cette thèse, nous avons étudié le comportement sous champ électrique de la séquence de phases des "cristaux liquides smectiques chiraux" en développant une étude sous champ électrique (E) et en fonction de la température (T) qui sont deux variables thermodynamiques indépendantes. Les résultats de mesures ont conduit au tracé des diagrammes de phase Champ électrique-Température (E-T). Ces diagrammes peuvent dans certains cas révéler l'induction sous champ électrique de nouvelles phases n'existant pas à champ nul. D'autre part, suite à l'étude de certains composés présentant la phase ferroélectrique SmC* dans leur séquence de phase à champ nul. Le tracé de leurs diagrammes de phases (E-T) a permis de mettre en évidence un problème de coexistence entre une phase paraélectrique et une autre ferroélectrique. Pour bien localiser cette séquence de phases sans rencontrer ce phénomène de démixtion, on a fait appel à une nouvelle étude optique sans champ électrique basée sur la méthode de conoscopie à balayage. L'analyse de l'ellipticité de la lumière transmise en fonction de la rotation de l'échantillon a donné accès aux deux indices de réfraction (ne et no) séparément, à la biréfringence (?n), au pouvoir rotatoire optique (PRO) et à la gyrotropie. Ces études que nous avons développé avec succès nous permettent une mise au point robuste et efficace des comportements des différentes phases de cristaux liquides smectiques chiraux sous et en absence du champ électrique. / In the first part of this thesis, we studied the behavior of the phase sequence of "smectic chiral liquid crystals" in order to develop a study under electric field (E) and as a function of tempertaure (T) which are two independent thermodynamic variables. The measurement results allow us to establish the electric field versus temperature phase diagram (E-T). In some cases, the phase diagram, under electric field, can reveal the induction of new phase which is not existing at zero field. On the other hand, we investigated certain compounds with ferroelectric phase SmC* in their phase sequence at zero field. The delimitation of phase diagrams (E-T) helped to highlight a coexistence problem between a paraelectric phase and a ferroelectric one. To locate this phase sequence without encountering this demixing phenomenon, we used a new optical study without electric field based on scanning conoscopy method. The analysis of the ellipticity of the transmitted light depending on the rotation of the sample gave access to the two refractive indices (ne and no) seperately, the birefringence (?n), the optical rotatory power (ORP) and the gyrotropy. These studies that we have successfully developed enable us to develop a robust and effictive behavior of different phases of chiral smectic liquid crystals under and without electric field.

Les matériaux multiferroïques sont des matériaux dans lesquels des ordres magnétiques, électriques et élastiques peuvent coexister dans une même phase. Ces ordres peuvent être couplés entre eux et l’étude de ces couplages permet de mieux comprendre les mécanismes à l’œuvre dans ces matériaux. Cette thèse porte sur l’étude de différents composés multiferroïques par spectroscopie Raman. Dans la ferrite de bismuth (BiFeO₃), l'effet de la contrainte sur le magnétisme, aussi bien sur les films minces (par contrainte épitaxiale) que le bulk (par pression hydrostatique) est étudié en détail. Cette thèse présente également une étude des excitations hybrides magnéto-électriques (électromagnons) dans les composés de type II à forte polarisation ferroélectrique comme CaMn₇O₁₂ et TbMnO₃. En outre, les modes de phonons ainsi que les excitations de basses énergies ont été étudiés (notamment sous champ magnétique) dans des composés au magnétisme frustré comme h-YMnO₃, h-YbMnO₃ et dans le langasite de fer au niobium. / Multiferroics are materials in which magnetic, electric and elastic orders can coexist in the same phase. These orders can be coupled to each other and their study of high interest to understand the mecanisms at stake in the multiferroic materials. This PhD thesis has been focused on the study of several multiferroic compounds by the mean of Raman spectroscopy. In bismuth ferrite (BiFeO₃), the effect of strain on the magnetic order, both on thin films (epitaxial strain) and single crystals (hydrostatic pressure), has been thoroughly investigated. This thesis also focuses on the study of hybrid magneto-electric excitations (electromagnons) in type II multiferroic compounds with strong ferroelectric polarizations such as CaMn₇O₁₂ and TbMnO₃. Furthermore, phonons modes and of low energy excitations have been measured and studied (especially under magnetic field) in compounds with frustrated magnetic orders such as h-YMnO₃, h-YbMnO₃ and in the niobium iron langasite (Ba₃NbFe₃Si₂O₁₄).