Master thesis deals with safety of aprotic electrolites used in lithium – ion accumulators. Beside conductivity and viscosity of electrolytes is work focused to flashpoint of electrolytes with flame retardants. In main part of work is shortly explained lithium ion accumulator used materials and fundamentals. Flame retardancy mechanisms and used materials are disscussed too. In practical part work deals with description of used measuring methods and evaluation of gauged data. At least optimal composition of electrolyte with flame retardant is proposed.

The thesis is devoted to the field of properties investigation of new types of electrolytes, and assess the appropriateness of electrolytes studied in this paper for use in Li -ion batteries. It focuses specifically on electrolytes based on aprotic solvents and their mixtures with the flame retardants. The goal of the thesis is to investigate the effects of FRAs on electrolyte mixtures via changes in specific conductivity and freezing point. These objectives were fulfilled by using electrochemical impedance spectroscopy in combination with a cryoscopic measurement method. There were overall 16 samples examined. The samples were prepared as a combination of chemicals, specifically Ethylene carbonate (EC), propylene carbonate (PC), dimethyl carbonate (DMC), dimethyl sulfone (DMSO2), triethyl phosphate (TEP) Dimethyl methylphosphonate (DMMP), triphenyl phosphate (TPP). Based on the results of the experiments, the mixtures were sorted according to the observed properties in the tables listed in the last part of this paper. These values can be further used to supplement the continuing research of electrolytes and also as assistance in searching for the new electrolyte mixtures.

Reclaimed water has increased in popularity as a means to recycle water and thus decrease the amount of wasteful water use. This process is widely used in Tampa Bay for watering of lawns. This increase in popularity and use has raised questions as to what contaminants are in the reclaimed water. The purpose of this study was to analyze reclaimed water for contaminants believed to be detrimental to health and conduct interviews to ascertain perceptions of risk in the local population. As water reuse grows in popularity further research will need to be conducted to address potential human health concerns. This research shows that there are potential health concerns related to reclaimed water when we use dioxin as a surrogate compound. Additionally, the research shows that local governments aren't doing enough to communicate information to local communities. Any policy that moves forward in regards to supplementing drinking water with reclaimed water must incorporate local communities in the decision making process. Decisions made in the absence of information can be misguiding and the first feedback of these decisions is felt by local communities. With their input in the beginning, throughout the decision making process, and during the evaluation period, new information will be generated. The incorporation of the community in the decision making process will make the reclaimed for drinking water initiative, more successful.

No description available.

No description available.

Global consumption of organophosphate esters (OPs), which are used as flame retardants and plasticizers, is rapidly increasing. Their use as additives in diverse applications poses a risk as they may be emitted from the products they are added to and be further transported in the environment. Therefore, the levels, distribution, and possible sources of 15 OPs, some of which are reported to be toxic, were investigated in indoor and outdoor environments. An exposure assessment was performed, and the exposure to OPs via inhalation was examined for five occupational groups. In addition, based on the findings of the studies, the total flow of OPs in Sweden was estimated. In indoor environments, the OPs detected in air and dust varied between the sites, but generally reflected the building materials, furniture etc. used in the premises. A majority of the analysed OPs were detected in all samples, and public buildings tended to have higher levels than domestic buildings. The chlorinated OPs dominated in indoor air and wipe samples from vehicles. They were also abundant in the dust samples. Some occupational groups were significantly more exposed to OPs than others. Aircraft technicians, for example, were exposed to about 500 times more tributyl phosphate than day care centre personnel. Upon domestic and industrial cleaning, OPs are discharged with the wastewater via the sewage system to sewage treatment plants (STPs). Irrespective of the size of the STPs investigated, they had similar levels of OPs in their influents, indicating that products containing OPs are widely used by the communities they serve. In some cases, it was possible to trace elevated levels of individual OPs to specific sources. The OPs were poorly removed from the wastewater, and the chlorinated OPs especially tended to pass through the STPs without being removed or degraded. Thus, levels of OPs in their effluents were also similar, as were the levels in their sludge. Of the total amounts of OPs entering the STPs, 50% was emitted to the recipients via the effluent. Hence, there is room for significant improvement in the treatment processes. Carps living in a pond, receiving STP effluent were found to contain relatively high levels of OPs compared to perch collected in lakes from background locations. Air and road traffic were also identified as sources of OPs: the concentration of total OPs in snow samples decreased with increasing distance from a major road intersection, and OPs were detected in aircraft lubricants and hydraulic fluids and in waste oil from cars and lorries. OPs are emitted from both diffuse and direct sources to the environment and may then be spread by long-range air transport, rivers and streams. This probably explains why OPs were also detected in air and fish from background locations. Finally, OPs are ubiquitous substances in both indoor and outdoor environments. The possibility that prolonged exposure to OPs at the levels found may cause adverse effects, for instance in aqueous organisms, cannot be excluded. For example, the OP levels in snow were of the same magnitude as reported effect concentrations. Similarly, in some premises, indoor exposure to OPs was close to the suggested guideline value. However, since these studies include only a limited number of samples, and data regarding the health and environmental effects of OPs are sparse, no definitive conclusions regarding their possible environmental effects can be drawn. / Den globala konsumtionen av organiska fosfatestrar (OP) för användning som flamskyddsmedel och mjukgörare har ökat kraftigt på senare tid. Det breda användningsområdet för dessa additiv medför en risk att de kan avges från de produkter de är satta till och transporteras vidare ut i miljön. Följaktligen undersöktes källor till, halter av, och fördelning i inom- och utomhusmiljöer av 15 OP, varav en del har toxiska effekter. Vidare har exponering för OP i bl.a bostäder och offentliga byggnader beräknats. Utöver detta undersöktes exponeringen för OP via inandning hos 5 yrkesgrupper. Slutligen användes resultaten för att uppskatta det totala flödet av OP i Sverige. I de olika inomhusmiljöerna uppmättes ett flertal OP i varierande halter i damm och luft, men generellt speglade halterna byggnadsmaterial, möbler etc. som fanns i lokalerna. De offentliga lokalerna tenderade att uppvisa högre halter än privata hus, förmodligen beroende på högre brandskyddskrav. Klorerade OP dominerade i inomhusluft samt i avstrykningsprov från fordon och förekom även i höga halter i damm. Vissa yrkesgrupper var exponerade för betydligt högre halter OP än andra, t.ex. exponerades flygtekniker för upp till 500 ggr högre lufthalter av tributylfosfat jämfört med förskollärare. I samband med våtskurning i inomhusmiljöer (hushåll, industrilokaler, osv.) släpps avsevärda mängder OP ut i avloppet och når till sist reningsverk. Oberoende av storlek på reningsverken var halterna av OP relativt lika, i vardera ingående vatten och slam, vilket indikerar en bred användning av OP i samhället. I vissa fall kunde specifika källor till OP i avloppsvattnet spåras. Exempelvis hade två av reningsverken högre halter av en klorerad OP jämfört med övriga reningsverk. Dessa behandlade vatten från en skumplastfabrik, respektive en fabrik som tillverkar flamskyddad färg. Avskiljningsgraden av OP från avloppsvatten visade sig generellt vara dålig, i synnerhet klorerade OP tenderade att passera genom reningsverken utan att degraderas eller avskiljas från vattnet. Av den mängd OP som nådde reningsverken släpptes 50 % ut till miljön via utflödet. Som ett resultat av detta uppvisade karpar från en damm påverkad av utflödet från ett reningsverk höga halter OP jämfört med abborrar från referenssjöar. Det finns därför anledning att förbättra tekniken på reningsverken. Flyg- och vägtrafik kunde också identifieras som källor till OP i miljön. OP uppmättes i hydrauloljor och smörjmedel för flygplan samt i spillolja från bilar och lastbilar. Vidare minskade totalhalten OP i snöprov med ökat avstånd från en större vägkorsning. OP släpps således ut från både diffusa och direkta källor och kan sedan spridas vidare via luft och vattendrag. Därmed var det inte förvånande att OP även påträffades i luft och fisk från bakgrundslokaler. Avslutningsvis förekommer OP i varierande halter i såväl inom- som utomhusmiljöer. Det kan inte uteslutas att långvarig exponering för de halter av OP som uppmätts skulle kunna orsaka negativa effekter hos t.ex vatten- eller jordlevande organismer. I smälta snöprov från en flygplats uppmättes exempelvis halter av OP i samma storleksordning som rapporterade effektkoncentrationer. Dessutom visade sig den beräknade exponeringen av OP, i några av de provtagna inomhuslokalerna, uppgå till halter nära det föreslagna riktvärdet för OP i Tyskland. Dessa studier inkluderar dock ett begränsat antal prov och provtyper och kunskapen om dessa föreningars miljö- och hälsoeffekter är bristfällig. Därför bedöms underlaget som för litet för att några definitiva slutsatser ska kunna dras angående OPs eventuella effekter på miljön.

Le comportement au feu de matériaux polymères peut changer plus ou moins fortement après vieillissement, mettant en péril les biens et les personnes en cas d’incendie. Ces changements dépendent du système considéré (nature du système retardateur de flamme, de la matrice polymère) et des conditions de vieillissement. Or jusqu’à aujourd’hui, les normes exigent l’évaluation de la réaction au feu d’un matériau juste après fabrication et rarement après un vieillissement représentatif des conditions réelles d’utilisation. L’évolution des caractéristiques des polymères ignifugés au cours du temps est actuellement peu connue, et seules quelques études ont eu lieu à ce sujet. Le travail de cette thèse concerne donc l’impact du vieillissement sur les performances au feu de systèmes complexes de polymères ignifugés. L’étude est basée sur les polymères polyméthacrylate de méthyle (PMMA) et acide polylactique (PLA) ; le système retardateur de flamme est quant à lui constitué de charges phosphorées et de silicates nanométriques. Un protocole de vieillissement et une méthodologie d’étude ont ensuite été mis en place pour déterminer l’influence du vieillissement sur les propriétés de ces matériaux : morphologie, masse molaire des polymères, dégradation des retardateurs de flamme, comportement au feu. Enfin, les caractéristiques des produits émis en phase gaz au cours de la combustion d’échantillons vieillis et non vieillis ont été analysées / The fire behaviour of polymeric materials can be modified after ageing, possibly leading to severe damages. These modifications depend on the chemical nature of the system (polymeric matrix, flame retardant system) and on the ageing conditions. Currently, norms exist, that define fire properties of fresh flame-retarded materials; but only few studies have been performed on aged materials. The aim of this work consists in evaluating the impact of ageing of flame-retarded materials. Firstly, materials have been processed from various formulations. The study focused on poly(methyl methacrylate) (PMMA) and poly(lactic acid) (PLA) polymers; flame-retardant system combining a phosphorus compound and mineral nanoparticles was added. Then an operating procedure has been created to simulate ageing, and a methodology has been developed to assess the characteristics of the composites before and after ageing (viscosity, morphology, fire behaviour). Finally, the combustion aerosols emitted by unaged and aged formulations have been investigated

Ces travaux de thèse portent sur la photodégradation de retardateurs de flamme bromés  (RFB) : décabromodiphényléther (BDE -209), tétrabromobisphénol A (TBBPA), TBBPA bis (allyl) éther (TBBPA-BAE) et TBBPA bis (2,3-dibromopropyl) éther (TBBPA- DBPE) en milieu solide et dans des échantillons réels. Nous avons d’abord caractérisé par chromatographie en phase liquide-haute résolution couplée à la spectrométrie de masse (LC-HR-MS) le BDE-209 et ses produits de dégradation dans des échantillons de textiles issus de sièges auto des véhicules hors usage (VHUs) des années 90. Puis, nous avons mené des expériences prouvant que ces produits de dégradation étaient d’origine photochimique. Dans un deuxième temps, nous avons étudié l’effet du polystyrène sur la photodégradation du BDE-209, TBBPA et ses dérivés et l’effet de ces RFBs sur la photodégradation du polystyrène. Des analyses par différentes techniques spectroscopiques et chromatographiques (IR, ATR-FTIR, GC-MS, SEC) ont mis en évidence un net effet d’accélération réciproque. La SEC (chromatographie d’exclusion stérique) a révélé une augmentation drastique des coupures de chaîne du PS avec fragmentation. En outre, des photoproduits résultant de l'oxydation du PS et de sa bromation par Br· ont été observés pour la première fois. L’existence de ces sous-produits suggère un nouveau mécanisme de transformation de PS en présence de RFB. Certains de ces photoproduits migrent dans l’eau et l’air, pouvant causer une pollution environnementale. / The main objective of this PhD thesis was to evaluate the photodegradation of brominated flame retardants (BFRs): decabromodiphenyl ether (BDE-209), tetrabromobisphenol A (TBBPA), TBBPA bis (allyl) ether (TBBPA-BAE) and TBBPA bis(2,3-dibromopropyl) ether (TBBPA-DBPE) in solid medium and real samples. As a first step, we characterized by liquid chromatography high-resolution-mass spectrometry (LC-HR-MS) the BDE-209 and its degradation products in textile samples from car seats of end-of-life vehicles (ELVs) of the 1990s. Then we demonstrated that these products were formed by photodegradation. In a second step, we investigated the effect of polystyrene on the photodegradation of BDE-209, TBBPA and its derivatives and the effect of these RFBs on the photodegradation of polystyrene. Analyses carried out by chromatography and spectroscopy techniques (IR, ATR-FTIR, GC-MS, SEC) revealed significant and mutual acceleration effects. SEC (exclusion size chromatography) showed a drastic increase in chain breaks of PS. Morover, additional photoproducts that may result from PS oxidation and Br • bromination has been observed for the first time. The formation of these byproducts suggests a new PS transformation mechanism in the presence of BFR. Some of these photoproducts can migrate into water and air causing environmental pollution.

Les polyesters insaturés sont des résines thermodurcissables particulièrement appréciées pour leur facilité de mise en œuvre et leur coût modéré. Cependant, comme tous les polymères organiques ils ont une réaction au feu médiocre, ce qui est critique dans un certains nombres de d'applications. L'objectif de cette thèse était d'élaborer de nouvelles formulations de résines ayant un comportement au feu amélioré. La première stratégie développée a été le greffage de monomères phosponés dans la matrice polyester. Des monomères méthacryliques et styrénique ont été synthétisés et utilisés pour remplacer une partie du styrène dans la résine. La stabilité thermique des résines modifiées est diminuée, mais leur comportement au feu est globalement meilleur. Des effets du phosphore en phase gazeuse et en phase condensée ont pu être mis en évidence.Dans une seconde partie, une sélection de particules se distinguant par leur nature, leur taille et leur facteur de forme a été testée. Si l'impact des ces charges est assez limité lorsqu'elles sont utilisées individuellement, des tests calorimétriques ont révélé que certaines combinaisons de particules pouvaient améliorer significativement la réaction au feu des résines. Enfin, des associations d'additifs phosphorés et de particules submicroniques ont été investiguées. Le polyphosphate d'ammonium se distingue des autres additifs par un impact très important sur le comportement au feu et particulièrement par le charbonnement important qu'il engendre, cependant sa combinaison avec des charges inorganiques ne s'est pas révélée probante. / Unsaturated polyesters are thermoset resins particularly appreciated for their low cost and easy processing. Nevertheless one of their main drawbacks is their poor fire resistance. The aim of this PhD thesis was to prepare new resin formulations with an improved fire behaviour. The first part of this work was dedicated to the grafting of phosphorous monomers in the polyester matrix. Methacrylic and styrenic monomers were synthesized and used to replace of part of the styrene in the resin. Resin thermal stability was decreased, but on the whole their fire behaviour was improved. Condensed phase and gas phase effects of phosphorus were highlighted.In a second part, a screening of various kinds of particles with different sizes was performed. Calorimetric tests revealed that, while the effect of these particles used alone is limited, a decrease of resin flammability could be achieved with specific combinations. Finally, commercial phosphorous additives were associated with submicronic fillers. From all the additives tested, ammonium polyphosphate stands out, with a powerful impact on the resin fire reaction and especially a much increased charring. However, its combination with inorganic particles was not conclusive.

La demande actuelle du marché du transport en matériaux composites à matrice polymère est en augmentation importante afin de remplacer les pièces aujourd’hui fabriquées en alliages métalliques par des matériaux plus légers et performants. Actuellement couramment utilisés, les composites thermodurcissables présentent l’inconvénient de ne pas être recyclables. Aussi, un des objectifs du projet « Résines idéales » durant lequel cette thèse a été réalisée est de mettre au point de nouveaux composites à matrice thermoplastique, doués de propriétés équivalentes. Parmi celles-ci, le comportement au feu est un enjeu essentiel pour leur développement et l’objectif de cette thèse est de développer de nouveaux systèmes retardateurs de flamme pour des matériaux composites thermoplastiques à fibres continues. Dans un premier temps, un screening des retardateurs de flamme phosphorés potentiellement efficaces a été effectué. L’étude de l’influence du renfort taffetas sur la stabilité thermique et le comportement au feu a également été réalisée (cône calorimètre, IOL, UL94). Ensuite, afin d’améliorer le comportement au feu, et en particulier, de satisfaire aux normes feu aéronautiques (les plus exigeantes), nous avons étudié des mélanges binaires et ternaires de retardateurs de flamme constitués du RF phosphoré sélectionné et d’autres charges : alumine, hydroxyde d’aluminium (ATH), graphite expansé, et 9,10-dihydro-9-oxy-10-phosphaphenanthrene-10-oxide (DOPO). Dans chaque cas, la stabilité thermique et le comportement au feu ont été caractérisés et discutés / The present demand of polymer-matrix composite materials in the transport market is significantly increasing, to replace the work-pieces actually manufactured in metal alloys, the polymer-matrix composite being lighter and more performant. Thermoset composites are currently and widely used however this kind of composites presents a severe drawback due to their non- recyclable character. One of the objectives of the “Résines idéales” project and of this thesis is to develop new composites made from thermoplastic matrix, endowed with similar properties. Among them, the fire behavior is a major challenge and the aim of this work is to develop new flame retardant systems for thermoplastics composites reinforced with continuous fibers. Firstly, we have performed a screening of potentially effective phosphorus flame retardants. Also, we have studied the influence of the reinforcement taffetas on the thermal stability and fire behavior. For that, various tests have been performed such as cone calorimeter, LOI and UL-94. Then, to improve the fire behavior and particularly to satisfy the aeronautical fire standards (the most challenging), we have studied binary and ternary mixtures of flame retardants constituted by the selected phosphorus flame retardant and other additives: alumina, aluminum hydroxide (ATH), expanded graphite and 9,10-dihydro-9-oxy-10-phosphaphenanthrene-10-oxide (DOPO). In each case, the thermal stability and fire behavior have been characterized and discussed