There has been unprecedented growth in wireless technologies in recent years; wireless devices such as cellular telephones and wireless local area network (WLAN) transceivers are becoming ubiquitous. It is now common for a single hardware device, such as a cellular telephone, to be capable of multi-band operation. Implementing a dedicated radio frequency (RF) front-end for each frequency band increases the component count and therefore the cost of the device. Consequently, there is now a requirement to design RF and microwave circuits that can be reconfigured to operate at different frequency bands, as opposed to switching between several fixed-frequency circuits. Barium strontium titanate (BST) thin films show great promise for application in reconfigurable microwave circuits. The material has a high dielectric constant which can be controlled by the application of a quasi-static electric field, combined with relatively low losses at microwave frequencies. Tunable microwave components based on BST-thin films have the potential to replace several fixed components, thereby achieving useful size and cost reductions. This thesis is concerned with the growth and microwave circuit applications of BST thin films on c- and r-plane sapphire substrates. Sapphire is an ideal substrate for microwave integrated circuit fabrication due to its low cost and low loss. Electronically tunable capacitors (varactors) were fabricated by patterning interdigital electrode structures on top of the BST films. High capacitance tunabilities of 56% and 64% were achieved for the films grown on c-plane and r-plane sapphire, respectively, at 40 V bias. A novel electronically tunable 3 dB quadrature hybrid circuit was also developed. Prototypes of this circuit were initially implemented using commercial varactor diodes, in order to validate the design. An integrated version of the coupler was then fabricated using BST varactors on c-plane sapphire. The results achieved demonstrate the potential of sapphire-based BST thin films in practical microwave circuits.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

Electromagnetic equations pertaining to electrically small dipole antennas and electrically small monopole antennas with small circular ground planes are reviewed. Two electrically small antenna designs are analyzed numerically and the results are compared. The first is a frequency agile version of the two-dimensional (2D) planar Egyptian axe dipole (EAD) antenna. The second is its three-dimensional (3D) counterpart. The frequency agile performance characteristics of both the 2D and 3D EAD designs are studied and compared. The potential for non-Foster augmentation to achieve large instantaneous fractional impedance bandwidths is detailed for each antenna. In addition, details are given on how to run frequency agile simulations in both ANSYS HFSS and Agilent's ADS. Details are also provided on how to generate an antenna's non-Foster |S₁₁| and radiation efficiency curves using HFSS, and how to generate an antenna's non-Foster |S₁₁| curve using ADS.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

No description available.

No description available.

Patch antennas are fundamental elements in many microwave communications systems. However, patch antennas receive/transmit signals over a very narrow bandwidth (typically a maximum of 3% bandwidth). Design modifications directed toward bandwidth expansion generally yield 10% to 40% bandwidth. The series varactor tuned patch antenna configuration was the bandwidth enhancement method explored in this research; this configuration is implemented by dividing a patch antenna into multiple sections and placing varactors across the resultant gaps. In addition to yielding a large bandwidth, the configuration has a number of ancillary benefits, including straightforward integration and design flexibility. Through the research represented by this work, the properties of the series varactor tuned patch antenna, herein referred to as the Fragmented Patch Antenna (or FPA), were explored and optimized. As a result, an innovative patch antenna was produced that yielded 63.4% frequency tuning bandwidth and covered a frequency range between 2.8 and 5.4 GHz. The wide bandwidth was achieved through a detailed parametric study. The products of this study were the discovery of multiple tuning resonances that were used to expand the tuning bandwidth and the understanding/documentation of the significance of specific antenna dimensions. Measurement results were obtained through the fabrication of a prototype antenna using semiconductor varactors. In the second research phase, the construction of capacitors using the tunable permittivity material Barium Strontium Titanate (BST) was investigated. Using this material in conjunction with nano-fabrication techniques, varactors were developed that had good estimated performance characteristics and were considered appropriate for integration into adaptive microwave circuitry, such as the tunable antenna system. The varactors were constructed by using Focused Ion Beam (FIB) milling to create a nano-scale capacitive gap in a transmission line. A combination of end-point current detection (EPD) and cross-section scanning electron (SEM) and ion beam (FIB) microscope images were used to optimize the milling procedure. The future extensions of this work include the integration of the BST varactors with the antenna design; the configuration of the developed BST varactors lends itself to a straightforward integration with the FPA antenna.

Avec le développement de l’internet des objets et l’augmentation des applications sans fil, les antennes sont de plus en plus présentes au quotidien. Cependant, l’implantation de ces antennes est un challenge tant d’un point de vue technologique (intégration des antennes dans les dispositifs), que psychologique (acceptabilité des antennes par le grand public). Dans ce contexte, le développement d’antennes optiquement transparentes permet non seulement leur implantation sur de nouvelles surfaces (vitrages d’immeubles, écrans de smartphones ...), mais promeut aussi leur acceptabilité par le grand public grâce à leur faible impact visuel. Ce travail présente la conception, la fabrication et la caractérisation d’antennes actives optiquement transparentes. Le matériau transparent et conducteur utilisé est un maillage métallique à pas micrométrique développé spécifiquement, alliant conductivité électrique et transparence optique élevées. Dans ce cadre, un premier prototype d’antenne transparente et miniature en bande FM utilisant un transistor MESFET de dimensions sub-millimétriques a été réalisé. Des antennes agiles en fréquence en bande X (~10 GHz) couplées, soit à une diode varicap localisée (agilité ~10%), soit à un matériau ferroélectrique (agilité ~2%), ont été développées et étudiées. Une antenne passive transparente a été conçue en bande V (~60 GHz). Enfin, une transition optique (1540 nm) / hyperfréquence (1,4 GHz) a été réalisée et caractérisée, basée sur la transmission optique d’un faisceau laser au travers du matériau constitutif de l’antenne. Pour l’ensemble des prototypes réalisés, une transparence optique supérieure à 80% dans le domaine du visible associée à une résistance par carré inférieure à 0,1 ohm/sq ont été utilisées. / Within the development of the Internet of Things (IoT) and the increase of the wireless communications, antennas are even more present on everyday life. However, antenna implementation is a real challenge, from a technological point of view (antenna integration into the devices) and from a psychological point of view (acceptability by the general public). Within this framework, the development of optically transparent antennas on new surfaces (glass windows, smartphone screens . . . ) is of great interest to improve the network coverage and to assist the general public in acceptability thanks to the low visual impact of such printed antennas. The present work deals with the design, the fabrication and the characterization of optically transparent and active antennas. The transparent and conducting material used is a micrometric mesh metal film specifically developed, associating high electrical conductivity and high optical transparency. A first optically transparent and miniature FM antenna based on a MESFET transistor with micrometric size has been designed and fabricated. Frequency agile antennas operating in X-band (~10 GHz), based on a beam-lead varactor (agility ~10%) and on a ferroelectric material agility ~2%), have been developed and characterized. An optically transparent and passive antenna has been studied in V-band (~60 GHz). At last, optics (1540 nm) / microwave (1.4 GHz) transition has been performed based on the transmission of a laser beam through the transparent antenna. For all prototypes, an optical transparency level higher than 80% coupled with a sheet resistance value lower than 0.1 ohm/sq have been used.