Moore's law has defined the semiconductor industry for the past 50 years. Devices continue to become smaller and increasingly integrated into the world around us. Beginning with personal computers, devices have become integrated into watches, phones, cars, clothing and tablets among other things. These devices have expanded in their functionality as well as their ability to communicate with each other through the internet. Further, devices have increasingly been required to have diverse of functionality. This combination of smaller devices coupled with diversification of device functionality has become known as more than Moore. In this thesis, more than Moore applications of graphene are explored in-depth. Graphene was discovered experimentally in 2004 and since then has fueled tremendous research into its various potential applications. Graphene is a desirable candidate for many applications because of its impressive electronic and mechanical properties. It is stronger than steel, the thinnest known material, and has high electrical conductivity and mobility. In this thesis, the potentials of graphene are examined for pressure sensors, humidity sensors and transistors. Through the course of this work, high sensitivity graphene pressure sensors are developed. These sensors are orders of magnitude more sensitive than competing technologies such as silicon nanowires and carbon nanotubes. Further, these devices are small and can be scaled aggressively. Research into these pressure sensors is then expanded to an exploration of graphene's gas sensing properties -- culminating in a comprehensive investigation of graphene-based humidity sensors. These sensors have rapid response and recovery times over a wide humidity range. Further, these devices can be integrated into CMOS processes back end of the line. In addition to CMOS Integration of these devices, a wafer scale fabrication process flow is established. Both humidity sensors and graphene-based transistors are successfully fabricated on wafer scale in a CMOS compatible process. This is an important step toward both industrialization of graphene as well as heterogeneous integration of graphene devices with diverse functionality. Furthermore, fabrication of graphene transistors on wafer scale provides a framework for the development of statistical analysis software tailored to graphene devices. In summary, graphene-based pressure sensors, humidity sensors, and transistors are developed for potential more than Moore applications. Further, a wafer scale fabrication process flow is established which can incorporate graphene devices into CMOS compatible process flows back end of the line. / <p>QC 20160610</p>

Barrier fabrics laminated with nanofiber membranes are used in protective textiles due to their ability to achieve high breathability or water vapor transmission rate (WVTR) while maintaining required barrier properties. The objective of this thesis is to investigate the factors impacting nanofiber membrane breathability. To achieve this objective, the effect of test conditions on breathability, and the relationship between fiber diameter, web porosity and breathability were explored. Nanofiber membranes were solution-spun by electrospinning from 15wt% and 20wt% PA6 solution concentrations, and by forcespinning from 20wt% and 25wt% concentrations. Three web area densities were made from each spinning method and solution combination: 5GSM, 10GSM and 15GSM. In order to investigate the impact of measurement conditions, breathability of all samples was measured by upright cup method (ASTM E96B) at two relative humidity levels (20% and 50%), and three air flow velocity levels (300fpm, 500fpm and 700fpm). The results showed that WVTR of all samples increased significantly when decreasing humidity or increasing air flow velocity. Webs with a lower density (5GSM or 10GSM) had higher changes of WVTR than those with a higher density (10GSM or 15GSM). These results indicate an interaction between the ambient conditions and the nanoweb structure, whereby conditions that are more conducive to water vapor transmission, such as 20%RH and 700fpm, are more discriminant between membranes. Both electropspun and forcespun membranes processed from the lower concentration solutions (15wt%, and 20wt%, respectively) exhibited smaller fiber diameters and smaller mean pore size. Overall, WVTR values varied with membrane thickness, and with solution concentration following a similar pattern as porosity. These effects were more accentuated for the forcespun samples, which had considerably larger pores (2811-5230nm) than the electrospun counterparts (163-298nm). Furthermore, samples forcespun by 20wt% solution were found to have clearly higher WVTR (1587-2194g/m²/24h at 700fpm) than electrospun samples (1526-1614g/m²/24h at 700fpm). This can be explained by the significant difference of pore size between electrospun and forcespun webs. It was concluded that breathability of forcespun samples, particularly those low density ones, could be effectively adjusted by solution concentration and is more sensitive to change of test conditions than that of electrospun webs. / text

Zn(_x)Co(_2-x)GeO(_4) materials were prepared and the variation in structure with composition was investigated using XED, SEM and EDX analysis. Limited series of solid solution were identified at both ends of the compositional range. D C electrical measurements were carried out to characterize the variation in the resistivity of the materials with humidity. Resistivities of the order of 10(^8) Ω m were observed in dry conditions, decreasing by 4 to 5 orders of magnitude with increasing humidity. Resistivity was not found to vary greatly with composition. Resistivity was temperature dependent, increasing by 1 to 2 orders of magnitude for a 70 C decrease in temperature. A C impedance measurements were performed to gain an understanding of the mechanism of the humidity dependent conductivity. At low frequencies impedance was found to be independent of frequency and humidity dependent. At high frequencies impedance was found to be inversely proportional to frequency and independent of humidity. The break point frequency was also humidity dependent and an increase in the impedance indicated inductive-type behaviour. Complex plane representation of the impedance gave a distorted semicircle at high frequencies and a low frequency tail. At high humidities the tail appears as a straight line, inclined at approximately 45 . At medium levels of humidity a distinctive loop is apparent at the intersection between the semicircle and the tail, corresponding to the inductive behaviour indicated at the break point frequency. The impedance response was modelled by an equivalent circuit consisting of various ideal and constant phase (dispersive) elements. The proposed mechanism of humidity-dependent conductivity is due to chemisorption and physisorption of water vapour from the atmosphere at the surface of the material, It is suggested that conduction occurs by hopping of protons between cheraisorbed hydroxyl groups at low humidities, by diffusion of H(_3)O(^+) ions between the hydroxyl groups at intermediate humidities and by hopping of protons between physisorbed H(_3)O(^+) ions (Grotthus Chain reaction) at high humidities.

The vine mealybug, Planococcus ficus (Signoret) (Homoptera: Pseudococcidae) is a pest with significant economic impact on the grape growing industry in South Africa and other parts of the world. With the isolation and synthesizing of the vine mealybug sex pheromone in 2001, new control options for the integrated management of the vine mealybug have been created. The status of sex pheromone monitoring as a tool in the integrated management of the vine mealybug has been evaluated from different perspectives. A significant quantitative difference in male vine mealybug trap catch numbers has been observed between wine and table grape vineyards and results indicated that there were differences in the susceptibility of grape cultivars to vine mealybug. Currently, the delta trap design is the accepted trap design for vine mealybug monitoring. No studies have yet been conducted to determine the optimum trap parameters like size or design. Population pressure may have an influence on the qualitative efficiency of various trap designs. The basis for degree-day forecasting models has been established adequately. However, refinements need to be done and the incorporation of factors such as humidity and regionality also need to be considered. Daily maximum temperatures fluctuating around the upper developmental threshold temperature for prolonged periods of time seemed to suppress population numbers. Different vineyard management practices exist for wine and table grape production. While an action threshold of 65 vine mealybug males per trap per two-week period seems an acceptable threshold for table grape production, it may not be appropriate for wine grape (or raisin grape) production. Using sex pheromone traps for population monitoring is a valid technique in the arsenal of management tactics against the vine mealybug. However, refinements and validation of research results must be done further to build credibility into the monitoring system. / Thesis (M. Environmental Science)--North-West University, Potchefstroom Campus, 2006.

Cementitious materials such as concrete, cement and gypsum are widely used in construction, as the raw materials of which they are made are abundant on Earth. Such trend is unlikely to change in the coming decades. But these materials suffer from creep. The creep of cementitious materials is a complex issue. On one hand, in cementitious materials creep is often coupled with other phenomena such as drying, hydration and cracking, and can be influenced by various parameters such as temperature, level of stress, water content and mix design. On the other hand, measuring creep by traditional macroscopic creep testing is time-consuming (creep test on concrete is recommended to be carried out over several months in order to provide a reliable characterization of long-term creep) and tedious, since experimental parameters need to be well controlled over extensive periods of time. This thesis studied microindentation at the scale of cement paste or gypsum plaster for the assessment of long-term basic creep properties of cementitious materials, by comparing creep functions obtained by minutes-long microindentation testing with those obtained with macroscopic creep experiments which lasted up to years. For cement paste, the comparison was made at the scale of concrete with the aid of upscaling tools. The study validated that minutes-long microindentation testing can provide a measurement of the long-term creep properties of cementitious materials. With the validated indentation technique, we studied the effect of microstructure (i.e., the distribution and the spatial organization of phases) and of water on long-term basic creep of cementitious materials. The effect of microstructure was studied on materials such as C3S pastes and C2S pastes as well as on compacts of synthetic C-S-H, portlandite (CH) and their mixtures prepared by compaction of powders. For all samples considered, we identified the right micromechanical model that allows predicting the results. The choice of micromechanical model was consistent with microstructural observations. The effect of relative humidity was studied by conditioning and testing some of those materials (i.e., C3S paste, compact of C-S-H, and compact of CH) in various relative humidities ranging from 11% to 94%. Relative humidity had a significant effect on creep: for all materials tested, a greater humidity led to a greater creep. The compact of portlandite was the most sensitive to relative humidity, probably because creep occurs at interfaces between portlandite crystals. For C3S paste, a linear relation was identified between long-term creep properties and water content at relative humidities ranging from 11% to 75%.Finally, we proposed micromechanical models that allow predicting long-term basic creep properties of cementitious materials with a wide range of volume fraction of crystalline phase and over a wide range of relative humidities

Additive manufacturing methods have been developed from rapid prototyping techniques and are now being considered as alternatives to conventional techniques of manufacturing. Stereolithography is one of the main additive methods and is considered highly accurate and consistent. Polymers are used as stereolithography materials and exhibit features such as high strength-to-weight ratio, corrosion resistance, ease of manufacturing and good thermal and electrical resistance properties. However, they are sensitive to environmental factors such as temperature, moisture and UV light, with moisture being identified as one of the most important factors that affect their properties. Moisture generally has an adverse effect on the mechanical properties of polymers. Investigation of the effects of moisture on polymers can be carried out using a number of experimental techniques; however, the benefits of the depth sensing indentation method over bulk tests include its ability to characterise various mechanical properties in a single test from only a small volume of material and the investigation of spatial variation in mechanical properties near the surface. The aim of this research was to investigate the effects of varying relative humidity on the indentation behaviour of stereolithography polymers and to develop a modelling methodology that can predict this behaviour under various humidities. It was achieved by a combination of experimental and numerical methods. Depth sensing indentation experiments were carried out at 33.5 %, 53.8 %, 75.3 % and 84.5 % RH (relative humidity) and 22.5 °C temperature to investigate the effects of varying humidity on the micron scale properties of the stereolithography resin, Accura 60. In order to minimise the effects of creep on the calculated properties, appropriate loading and unloading rates with suitable dwell period were selected and indentation data was analysed using the Oliver and Pharr method (1992). A humidity control unit fitted to the machine was used to condition the samples and regulate humidity during testing. Samples were also preconditioned at 33.5 %, 53.8 %, 75.3 % and 84.5 % RH using saturated salt solutions and were tested at 33.5 % RH using humidity control unit. It was seen that properties such as indentation depth increased and contact iv hardness and contact modulus decreased with increasing RH. The samples conditioned and tested using the humidity control unit at high RH showed a greater effect of moisture than the preconditioned samples tested at 33.5 % RH. This was because the samples preconditioned at high RH exhibited surface desorption of moisture when tested at ambient RH, resulting in some recovery of the mechanical properties. In order to investigate these further, tests were performed periodically on saturated samples after drying. Ten days drying of samples conditioned for five days at 84.5 % RH provided significant, though not complete, recovery in the mechanical properties. These tests confirmed that Accura 60 is highly hygroscopic and its mechanical properties are a function of RH and removal of moisture leads to a significant recovery of the original mechanical properties.

The role of nitric acid (HNO3) on the atmospheric corrosion of metals has so far received little or no attention. However, the last decades of decreasing sulphur dioxide (SO2) levels and unchanged HNO3 levels in many industrialized countries have resulted in an increased interest in possible HNO3-induced atmospheric corrosion effects. In this study a new method was developed for studying the corrosion effects of HNO3 on metals at well-defined laboratory exposure conditions. The method has enabled studies to be performed on the influence of individual exposure parameters, namely HNO3-concentration, air velocity, temperature and relative humidity, as well as comparisons with newly generated field exposure data. The corrosion rate and deposition rate of HNO3 on copper was shown to follow a linear increase with HNO3 concentration. The deposition velocity (Vd) of HNO3 increased up to an air velocity of 11.8 cm s-1. Only at a higher air velocity (35.4 cm s-1) the Vd on copper was lower than the Vd on an ideal absorbent, implying the Vd of HNO3 at lower air velocities to be mass-transport limited. Within the investigated temperature range of 15 to 35 ºC only a minor decrease in the HNO3-induced copper corrosion rate could be observed. The effect of relative humidity (RH) was more evident. Already at 20 % RH a significant corrosion rate could be measured and at 65 % RH the Vd of HNO3 on copper, zinc and carbon steel reached maximum and nearly ideal absorption conditions. During identical exposure conditions in HNO3-containing atmosphere, the corrosion rate of carbon steel was nearly three times higher than that of copper and zinc. The HNO3-induced corrosion effect of copper, zinc and steel turned out to be significantly higher than that induced by SO2 alone or in combination with either NO2 or O3. This is mainly attributed to the much higher water solubility and reactivity of HNO3 compared to SO2, NO2 and O3. Relative to SO2, zinc exhibits the highest sensitivity to HNO3, followed by copper, and carbon steel with the lowest sensitivity. Extrapolation of laboratory data to an assumed average outdoor wind velocity of 3.6 m s-1 enabled a good comparison with field data. Despite the fact that ambient SO2 levels are still much higher than HNO3 levels, the results show that HNO3 plays a significant role for the atmospheric corrosion of copper and zinc, but not for carbon steel. The results generated within this doctoral study emphasize the importance of further research on the influence of HNO3 on degradation of other materials, e.g. stone and glass, as well as of other metals.

Die Schallgeschwindigkeit in der Luft hängt wesentlich von der Temperatur, aber auch in gewissen Maße von deren Feuchtigkeit und Zusammensetzung, ab. Den Einfluss der Lufttemperatur auf die Schallgeschwindigkeit nutzen Messverfahren aus, um aus der Laufzeit von Schallsignalen die Temperatur entlang des Ausbreitungsweges zu bestimmen. Dabei wird jedoch häufig die Beeinflussung durch die Luftfeuchte unzureichend berücksichtigt. Hier wird ein Verfahren aufgezeigt, das die Zusammensetzung der Luft und die Temperaturabhängigkeit der spezifischen Wärmen detailliert berücksichtigt. Die auf diesem Wege aus der Schallgeschwindigkeit abgeleitete Temperatur wird mit der in der Mirkometeorologie üblichen Approximation der akustisch virtuellen Temperatur verglichen. / The speed of sound in humid air depends besides the temperature to some degree on their humidity and compositions. Several measuring methods uses the influence of the temperature on speed of sound to calculate from the travel time of acoustic signals the temperature along the propagation path. However, thereby the influence of the humidity is often ignored. This paper described a method, which take the impact of the atmospheric composition and the temperature dependence of the specific heats explicit into account. The subsequent from the speed of sound recalculated temperature is compared with the mircometeorological standard approximation, the acoustic virtual temperature.

Zur Validierung des Verfahrens der akustischen Tomographie, das als Fernerkundungssverfahren trägheits- und berührungslos arbeitet, werden Vergleichsmessungen mit herkömmlichen Sensoren für die Lufttemperatur und Luftfeuchte durchgeführt. Dabei zeigen sich die Grenzen der Erfassung dieser Größen in Bezug auf Strahlungseinfluss und Trägheit der Messgeräte. Hier werden einige Probleme bei der Verwendung konventioneller Hütten und Lösungsvorschläge aufgezeigt. / In order to validate measurements with the acoustic tomography, which operates as an remote sensing system lagless and contactless, comparison measurements were performed with conventional sensors for the air temperature and humidity. The accuracy of these quantities is limited by the radiation influence and the lag of the instruments. Here some difficulties are pointed out by using conventional shelters and solutions are demonstrated.

The dynamic properties of several rectangular and V-shaped microcantilevers were investigated. Particular attention was paid to the higher flexural eigenmodes of oscillation. The potential of the higher flexural modes was demonstrated through the use of cantilevers as standalone sensors for adsorbed mass. The mass adsorbed on the surface of a cantilever was in the form of a homogeneous water layer measured as a function of relative humidity. The minimum detectable water layer thicknesses were 13.7 Å, 3.2 Å, 1.1 Å, and 0.7 Å for the first four modes of a rectangular cantilever, clearly demonstrating enhanced accuracy for the higher eigenmodes of oscillation. These thicknesses correspond to minimum detectable masses of 33.5 pg, 7.8 pg, 2.7 pg and 1.7 pg for the first four modes. For quantitative applications the spring constants of each cantilever must be determined. Many methods exist but only a small number can calibrate the higher flexural eigenmodes. A method was developed to simultaneously calibrate all flexural modes of microcantilever sensors. The method was demonstrated for the first four eigenmodes of several rectangular and V-shaped cantilevers with nominal fundamental spring constants in the range of 0.03 to 1.75 N/m. The spring constants were determined with accuracies of 5-10 %. Spring constants of the fundamental mode were generally in agreement with those determined using the Sader method. The method is compatible with existing AFM systems. It relies on a flow of gas from a microchannel and as such poses no risk of damage to the cantilever beam, its tip, or any coating. A related method was developed for the torsional modes of oscillation. Preliminary results are shown for the fundamental mode of a rectangular cantilever. The method can be easily extended to the higher torsional modes, V-shaped cantilevers, and potentially, the flapping modes of the legs of V-shaped microcantilevers.