Recentemente, o Brasil adotou o padrão SBTVD (Sistema Brasileiro de TV Digital) para transmissão de TV digital. Este utiliza o CODEC (codificador e decodificador) de vídeo H.264/AVC, que é considerado o estado-da-arte no contexto de compressão de vídeo digital. Esta transição para o SBTVD requer o desenvolvimento de tecnologia para transmissão, recepção e decodificação de sinais, assim, o projeto Rede H.264 SBTVD foi iniciado e tem como um dos objetivos a produção de componentes de hardware para construção de um set-top box SoC (System on Chip) compatível com o SBTVD. No sentido de produzir IPs (Intellectual Property) para codificação e decodificação de vídeo digital segundo o padrão H.264/AVC, várias arquiteturas de hardware vêm sendo desenvolvidas no âmbito do projeto. Assim, o objetivo deste trabalho consiste na realização da implementação física em ASIC (Application-Specific Integrated Circuit) de algumas destas arquiteturas de hardware para decodificação de vídeo H.264/AVC, entre elas as arquiteturas parser e decodificação de entropia, predição intra-quadro e, por fim, quantização e transformadas inversas, que juntas formam uma versão funcional de um decodificador de vídeo H.264 chamado de decodificador intra-only. Além destas, também foi fisicamente implementada uma arquitetura para o módulo filtro redutor de efeito de bloco e arquiteturas para os perfis Main e High de um compensador de movimentos. Nesta dissertação de mestrado, é apresentada a metodologia de implementação standard-cells (ASIC) utilizada, assim como uma descrição detalhada de cada passo executado para se chegar ao leiaute de cada uma das arquiteturas. Também são apresentados os resultados das implementações e realizadas algumas comparações com outras implementações de arquiteturas descritas na literatura. A implementação do filtro possui 43,9K portas lógicas (equivalent-gates), 42mW de potência e possui a menor quantidade de memória interna, 12,375KB SRAM, quando comparada com outras implementações para a mesma resolução de vídeo, 1920x1080@30fps. As implementações para os perfis Main e High do compensador de movimento apresentam a melhor relação entre a quantidade de ciclos de relógio necessária para interpolar um macrobloco (MB), 304 ciclos/MB, e a quantidade de equivalent-gates de cada implementação, 98K e 102K, respectivamente. Já a implementação do decodificador H.264 intra-only possui 5KB SRAM, 11,4mW de potência e apresenta a menor quantidade de equivalent-gates, 150K, comparado com outras implementações de decodificadores H.264 com características similares. / Recently Brazil has adopted the SBTVD (Brazilian Digital Television System) for digital TV transmission. It uses the H.264/AVC video CODEC (coder and decoder), which is considered the state of the art in the context of digital video compression. This transition to the SBTVD standard requires the development of technology for transmitting, receiving and decoding signals, so a project called Rede H.264 was initiated with the objective of producing cutting edge hardware components to build a set-top box SoC (System on Chip) compatible with the SBTVD. In order to produce IPs (Intellectual Property) for encoding and decoding digital video according to the H.264/AVC standard, many hardware architectures have been developed under the project. Therefore, the objective of this work is to carry out the physical implementation flow for ASIC (Application-Specific Integrated Circuit) in some of these hardware architectures for H.264/AVC video decoding, including the architectures parser and entropy decoding, intra-prediction and inverse quantization and transforms, which together compound a working version of an H.264 video decoder called intra-only. Besides these architectures, it is also physically implemented an architecture for a deblocking filter module and architectures for motion compensation according the Main and High profiles. This master thesis presents the standard-cells (ASIC) implementation as well as a detailed description of each step necessary to outcome the layouts of each of the architecture. It also presents the results of the implementations and comparisons with other works in the literature. The implementation of the filter has 43.9K gates (equivalent-gates), 42mW of power consumption and it demands the least amount of internal memory, 12.375KB SRAM, when compared with other implementations for the same video resolution, 1920x1080@30fps. The implementations for the Main and High profiles of the motion compensator have the best relationship between the amount of required clock cycles to interpolate a macroblock (MB), 304 cycles/MB, and the equivalent-gate count of each implementation, 98K and 102K, respectively. Also, the implementation of the H.264 intra-only decoder has 5KB SRAM, 11.4 mW of power consumption and it has the least equivalent-gate count, 150K, compared with other implementations of H.264 decoders which have similar features.

Este trabalho apresenta o desenvolvimento de uma nova ferramenta para a síntese automática de células, a partir de uma descrição estrutural no nível lógico. A ferramenta esta sendo integrada ao sistema TRAMO3, e visa eliminar a necessidade do use de biblioteca de células na geração de circuitos. Uma revisão sobre síntese de leiaute e metodologias de projeto é apresentada. A metodologia TRANCA é descrita de forma sucinta e os sistemas TRAMO2 e TRAMO3, assim como o roteador MARTE são analisados em detalhe para indicar o contexto onde se insere o trabalho. As principais alternativas para a geração de células são analisadas e o algoritmo descrito em [REI 93b] é utilizado com algumas modificações, levando em conta situações praticas. Os seguintes passos são executados durante o processo: posicionamento dos transistores, roteamento das conexões internas e compactação do leiaute. Finalmente, alguns melhoramentos no gerador são propostos, de forma a eliminar algumas restrições impostas na primeira versão. / This work presents the development of a new tool for automatic cell synthesis, starting from a structural description at the logic level. The tool is currently being integrated to TRAMO3 system, and aims at eliminating the need of cell libraries utilization during the circuit generation. A brief review about layout synthesis and design methodologies is presented. TRANCA design approach is briefly described and the TRAMO2 and TRAMO3 systems, as well as the MARTE router are analyzed with some detail in order to show the environment where the work is inserted. The main alternatives for cell generation are analyzed and the algorithm described in [REI 93b] is used with some changes, taking into account practical situations. The following steps are executed during the process: transistor placement, routing of internal connections and layout compaction. Finally, some improvements to the generator are proposed, in order to remove some restrictions imposed in the first version.

Grace aux récents développements des technologies d’intégration, il est aujourd’hui possible d’envisager la réalisation de circuits et systèmes intégrés sur Silicium fonctionnant à des fréquences auparavant inatteignables. Par conséquence, depuis quelques années, on assiste à la naissance de nouvelles applications en bande millimétrique, comme la communication sans fil à haut-débit à 60GHz, les radars automobiles à 76-77 et 79-82GHz, et l’imagerie millimétrique à 94GHz.Cette thèse vise, en premier lieu, à la définition d’une méthodologie de conception des circuits intégrés en bande millimétrique. Elle est par la suite validée au travers de son application à la conception des amplificateurs faible-bruit en technologie BiCMOS SiGe. Dans ce contexte, une attention particulière a été portée au développement d’une stratégie de conception et de modélisation des inductances localisées. Plusieurs exemples d’amplificateurs faible-bruit ont été réalisés, à un ou deux étages, employant des composants inductifs localisés ou distribués, à 60, 80 et 94 GHz. Tous ces circuits présentent des caractéristiques au niveau de l’état de l’art dans le domaine, ainsi en confirmant l’exactitude de la méthodologie de conception et son efficacité sur toute la planche de fréquence considérée. En outre, la réalisation d’un récepteur intégré pour applications automobiles à 80GHz est aussi décrite comme exemple d’une possible application système, ainsi que la co-intégration d’un amplificateur faible-bruit avec une antenne patch millimétrique intégrée sur Silicium. / The interest towards millimeter waves has rapidly grown up during the last few years, leading to the development of a large number of potential applications in the millimeter wave band, such as WPANs and high data rate wireless communications at 60GHz, short and long range radar at 77-79GHz, and imaging systems at 94GHz.Furthermore, the high frequency performances of silicon active devices (bipolar and CMOS) have dramatically increased featuring both fT and fmax close or even higher than 200GHz. As a consequence, modern silicon technologies can now address the demand of low-cost and high-volume production of systems and circuits operating within the millimeter wave range. Nevertheless, millimeter wave design still requires special techniques and methodologies to overcome a large number of constraints which appear along with the augmentation of the operative frequency.The aim of this thesis is to define a design methodology for integrated circuits operating at millimeter wave and to provide an experimental validation of the methodology, as exhaustive as possible, focusing on the design of low noise amplifiers (LNAs) as a case of study.Several examples of LNAs, operating at 60, 80, and 94 GHz, have been realized. All the tested circuits exhibit performances in the state of art. In particular, a good agreement between measured data and post-layout simulations has been repeatedly observed, demonstrating the exactitude of the proposed design methodology and its reliability over the entire millimeter wave spectrum. A particular attention has been addressed to the implementation of inductors as lumped devices and – in order to evaluate the benefits of the lumped design – two versions of a single-stage 80GHz LNA have been realized using, respectively, distributed transmission lines and lumped inductors. The direct comparison of these circuits has proved that the two design approaches have the same potentialities. As a matter of fact, design based on lumped inductors instead of distributed elements is to be preferred, since it has the valuable advantage of a significant reduction of the circuit dimensions.Finally, the design of an 80GHz front-end and the co-integration of a LNA with an integrated antenna are also considered, opening the way to the implementation a fully integrated receiver.

This project focuses on a prototype system architecture which integrates features of an event-driven gate-level simulator and features of the multiple expert system architecture, HEARSAY-II. Combining artificial intelligence and simulation techniques, a knowledge-based simulator was designed and constructed to model non-standard circuit behavior. This non-standard circuit behavior is amplified by advances in integrated circuit technology. Currently available digital circuit simulators can not simulate this behavior. Circuit designer expertise on behavioral phenomena is used in the expert system to guide the base simulator by manipulating its events to achieve the desired behavior.

We have developed a placement-aware 3-D floorplanning algorithm that enables additional wirelength reduction by planning for 3-D placement of logic gates in selected circuit modules during the floorplanning stage. Thus it also bridges the existing gap between 3-D floorplanning and 3-D placement. To reduce the solution space of 3-D floorplanning which is known to be an NP-hard problem, we derive a set of feasibility conditions on the topological representation of a floorplan. In addition, we have designed a fast module packing algorithm that satisfies a set of constraints for placement-aware 3-D floorplanning. Furthermore, we have designed an efficient evolutionary algorithm that is used in the proposed 3-D floorplanning algorithm for multi-objective combinatorial optimization. Our results show that the proposed placement-aware 3-D floorplanning algorithm is very fast, and it reduces the system level total wirelength by 9.8% compared to existing state-of-the-art floorplanning tools that do not plan for 3-D placement of floorplanning modules.

No description available.

No description available.

The work presents a novel voltage biasing design that helps the CMOS RF circuits resilient to variability and reliability. The biasing scheme provides resilience through the threshold voltage (VT) adjustment, and at the mean time it does not degrade the PA performance. Analytical equations are established for sensitivity of the resilient biasing under various scenarios. Power Amplifier (PA) and Low Noise Amplifier (LNA) are investigated case by case through modeling and experiment. PTM 65nm technology is adopted in modeling the transistors within these RF blocks. A traditional class-AB PA with resilient design is compared the same PA without such design in PTM 65nm technology. Analytical equations are established for sensitivity of the resilient biasing under various scenarios. A traditional class-AB PA with resilient design is compared the same PA without such design in PTM 65nm technology. The results show that the biasing design helps improve the robustness of the PA in terms of linear gain, P1dB, Psat, and power added efficiency (PAE). Except for post-fabrication calibration capability, the design reduces the majority performance sensitivity of PA by 50% when subjected to threshold voltage (VT) shift and 25% to electron mobility (μn) degradation. The impact of degradation mismatches is also investigated. It is observed that the accelerated aging of MOS transistor in the biasing circuit will further reduce the sensitivity of PA. In the study of LNA, a 24 GHz narrow band cascade LNA with adaptive biasing scheme under various aging rate is compared to LNA without such biasing scheme. The modeling and simulation results show that the adaptive substrate biasing reduces the sensitivity of noise figure and minimum noise figure subject to process variation and iii device aging such as threshold voltage shift and electron mobility degradation. Simulation of different aging rate also shows that the sensitivity of LNA is further reduced with the accelerated aging of the biasing circuit. Thus, for majority RF transceiver circuits, the adaptive body biasing scheme provides overall performance resilience to the device reliability induced degradation. Also the tuning ability designed in RF PA and LNA provides the circuit post-process calibration capability.

This dissertation presents the design and development of a multi-processor logic simulator. After an introduction to parallel processing, the concept of distributed simulation is described as well as the possibility of deadlock in a distributed system. It is proven that the proposed system does not deadlock. Next, the modeling techniques are discussed along with the timing mechanisms used for logic simulation. A new approach, namely process oriented simulation is studied in depth. It is shown that modeling for this kind of simulation is more efficient regarding modeling ease, computer memory and simulation time, than existing simulation methods. The hardware design of the multi-processor system and the algorithms for synchronization and signal interchange between the processors are presented next. An algorithm for an efficient partitioning of the digital network to be simulated among the processors of the system is also described. Apart from the simulation of a single digital network, the simulator can also be used for fault simulation and design verification. Regarding fault simulation, the fault injection and fault detection techniques are presented. The experimental results obtained by running the multi-processor simulator are compared with the theoretical estimates as well as with results obtained by other multi-processor systems. The comparison shows that the proposed simulator exhibits the estimated performance. Finally, the design of a common bus interface is given. This interface will connect the processors of the system directly without the intervention of a hard disk which was used for the development and testing of the system. / Ph. D.

Thesis (D. Tech. (Engineering: Electrical)) -- Central University of technology, Free State, 2012 / This thesis describes a method for the automatic generation of appli- cation speci_c processors. The thesis was organized into three sepa- rate but interrelated studies, which together provide: a justi_cation for the method used, a theory that supports the method, and a soft- ware application that realizes the method. The _rst study looked at how modern day microprocessors utilize their hardware resources and it proposed a metric, called core density, for measuring the utilization rate. The core density is a function of the microprocessor's instruction set and the application scheduled to run on that microprocessor. This study concluded that modern day microprocessors use their resources very ine_ciently and proposed the use of subset processors to exe- cute the same applications more e_ciently. The second study sought to provide a theoretical framework for the use of subset processors by developing a generic formal model of computer architecture. To demonstrate the model's versatility, it was used to describe a number of computer architecture components and entire computing systems. The third study describes the development of a set of software tools that enable the automatic generation of application speci_c proces- sors. The FiT toolkit automatically generates a unique Hardware Description Language (HDL) description of a processor based on an application binary _le and a parameterizable template of a generic mi- croprocessor. Area-optimized and performance-optimized custom soft processors were generated using the FiT toolkit and the utilization of the hardware resources by the custom soft processors was character- ized. The FiT toolkit was combined with an ANSI C compiler and a third-party tool for programming _eld-programmable gate arrays (FPGAs) to create an unconstrained C-to-silicon compiler.