One of the important factors determining the lifetime of polymer electrolyte membrane fuel cells (PEMFCs) is membrane degradation and failure. The lack of effective mitigation methods is largely due to the currently very limited understanding of the underlying mechanisms for mechanical and chemical degradations of fuel cell membranes. In order to understand degradation of membranes in fuel cells, two different experimental approaches were developed; one is fuel cell testing under open circuit voltage (OCV) with bi-layer configuration of the membrane electrode assemblies (MEAs) and the other is a modified gas phase Fenton's test. Accelerated degradation tests for polymer electrolyte membrane (PEM) fuel cells are frequently conducted under open circuit voltage (OCV) conditions at low relative humidity (RH) and high temperature. With the bi-layer MEA technique, it was found that membrane degradation is highly localized across thickness direction of the membrane and qualitatively correlated with location of platinum (Pt) band through mechanical testing, Infrared (IR) spectroscopy, fluoride emission, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive spectroscopy (EDS) measurement. One of the critical experimental observations is that mechanical behavior of membranes subjected to degradation via Fenton's reaction exhibit completely different behavior with that of membranes from the OCV testing. This result led us to believe that other critical factors such as mechanical stress may affect on membrane degradation and therefore, a modified gas phase Fenton's test setup was developed to test the hypothesis. Interestingly, the results showed that mechanical stress directly accelerates the degradation rate of ionomer membranes, implying that the rate constant for the degradation reaction is a function of mechanical stress in addition to commonly known factors such as temperature and humidity. Membrane degradation induced by mechanical stress necessitates the prediction of the stress distribution in the membrane under various conditions. One of research focuses was on the developing micromechanism-inspired continuum model for ionomer membranes. The model is the basis for stress analysis, and is based on a hyperelastic model with reptation-inspired viscous flow rule and multiplicative decomposition of viscoelastic and plastic deformation gradient. Finally, evaluation of the membrane degradation requires a fuel cell model since the degradation occurs under fuel cell operating conditions. The fuel cell model included structural mechanics models and multiphysics models which represents other phenomena such as gas and water transport, charge conservation, electrochemical reactions, and energy conservation. The combined model was developed to investigate the compression effect on fuel cell performance and membrane stress distribution.

No description available.

No description available.

Low molecular weight liquid polybutadienes (1000 – 2000 g/mol) consisting of 60 mol% 1,2-polybutadiene repeating units were synthesized via anionic telomerization and conventional anionic polymerization. Maintaining the initiation and reaction temperature less than 70 °C minimized chain transfer and enabled the telomerization to occur in a living fashion, which resulted in well-controlled molecular weights and narrow polydispersity indices. MALDI-TOF mass spectrometry confirmed that the liquid polybutadienes synthesized via anionic telomerization contained one benzyl end and one protonated end. Subsequently, 2-ureido-4[1H]-pyrimidone (UPy) quadruple hydrogen-bonding was introduced to telechelic poly(ethylene-co-propylene), and mechanical characterization of the composites with UPy-functionalized carbon nanotubes was performed. The composites enhanced the mechanical properties and the UPy-UPy association between the matrix polymer and carbon nanotubes prevented the decrease of an elongation at break. The matrix polymer was also reinforced without sacrificing the processability. Additionally, UPy groups were introduced to styrene-butadiene rubbers (SBRs). Introducing UPy groups to SBRs drastically changed the physical properties of these materials. Specifically, the SCMHB networks served as mechanically effective crosslinks, which raised Tg and enhanced the mechanical performance of the SBRs. Novel site-specific sulfonated graft copolymers, poly(methyl methacrylate)-g-(poly(sulfonic acid styrene)-b-poly(tert-butyl styrene)), poly(methyl methacrylate)-g-(poly(tert-butyl styrene)-b-poly(sulfonic acid styrene)), and the corresponding sodium sulfonate salts were successfully synthesized via living anionic polymerization, free radical graft copolymerization, and post-sulfonation strategies. The graft copolymers contained approximately 9 – 10 branches on average and 4 wt% of sulfonic acid or sodium sulfonate blocks adjacent to the backbone or at the branch terminus. The mobility of the sulfonated blocks located at the branch termini enabled the sulfonated blocks to more readily interact and form ionic aggregates. The glass transition temperatures (Tg) of the sulfonated graft copolymers with sulfonated blocks at the branch termini were higher than that of copolymers with sulfonated blocks adjacent to the backbone. More facile aggregation of sulfonated blocks at the branch termini resulted in the appearance of ionomer peaks in SAXS whereas ionomer peaks were not observed in sulfonated graft copolymers with sulfonated blocks adjacent to the backbone. In addition, similar analogues, novel site-specific sulfonated graft copolymers, poly(methyl methacrylate)-g-(poly(sulfonic acid styrene)-b-poly(ethylene-co-propylene)) (PMMA-g-SPS-b-PEP), poly(methyl methacrylate)-g-(poly(ethylene-co-propylene)-b-poly(sulfonic acid styrene)) (PMMA-g-PEP-b-SPS), and the corresponding sodium sulfonate salts were successfully synthesized. Estimated ï £N values predicted the phase separation of each block and differential scanning calorimetry (DSC) and dynamic mechanical analysis confirmed the phase separation of each block component of the graft copolymers. The aggregation of sulfonic acid or sodium sulfonate groups at the branch termini restricted the glass transition of the PEP block. This lack of the glass transition of the PEP block resulted in higher storage modulus than a sulfonated graft copolymer with sulfonated blocks adjacent to the backbone. The location of sulfonated blocks in both sulfonic acid and sodium sulfonate graft copolymers significantly affected the thermal, mechanical and morphological properties. Lastly, symmetric (16000 g/mol for each block) and asymmetric (14000 g/mol and 10000 g/mol for each block) poly(ethylene-co-propylene)-b-poly(dimehtylsiloxane) (PEP-b-PDMS) were synthesized using living anionic polymerization and subsequent hydrogenation. The onset of thermal degradation for the PEP-b-PDMS diblock copolymer was higher than 300 ºC and PEP-b-PDMS was more thermally stable than the precursor diblock copolymer, polyisoprene-b-PDMS. DSC analysis of PEP-b-PDMS provided Tg of PDMS -125 ºC, Tg of PEP -60 ºC, Tc of PDMS -90 ºC, and Tm of PDMS -46 and -38 ºC, respectively. Appearance of thermal transitions of each PEP and PDMS block revealed the formation of phase separation. Estimated Ï N also supported the phase separation. / Ph. D.

Use of a mixed triisobutylaluminum/1,1-diphenylhexyllithium intiator enabled the anionic polymerization of methyl methacrylate at room temperature, resulting in narrow molecular weight distributions and syndiorich structures. Polymerizations were controlled above Al:Li = 2, and control significantly decreased at elevated temperatures above 25 °C. A significant increase in Tg with increasing control of syndiotacticity demonstrated the ability to tailor polymer properties using this technique. Analysis with MALDI-TOF/TOF spectroscopy revealed the dominance of a back-biting side reaction at elevated temperatures. Hydroxy-functional random and block copolymers of n-butyl acrylate (nBA) and 2-hydroxyethyl acrylate were synthesized using nitroxide mediated polymerization. Controlled polymerization was demonstrated, resulting in narrow polydispersities and linear molecular weight vs. conversion plots. In situ FTIR spectroscopy monitored the polymerizations and revealed pseudo first order rate kinetics for random copolymerizations. Protection of the hydroxyl using trimethylsilyl chloride alleviated isolation issues of amphiphilic polymer products. For the first time zwitterion-containing copolymers were electrospun to form nanoscale fibers with diameters as low as 100 nm. Free radical copolymerization of nBA and sulfobetaine methacrylamide produced zwitterionic copolymers with 6-13 mol % betaine. Dynamic mechanical analysis revealed a rubbery plateau and biphasic morphology similar to ionomers. Electrospinning from chloroform/ethanol solutions (80/20 v/v) at 2-7 wt % afforded polymeric fibers at viscosities below 0.02 Pa™s, which is the lowest viscosity observed for fiber formation in our laboratories. We hypothesized that intermolecular interactions rather than chain entanglements dominated the electrospinning process. Solution rheology of zwitterionic copolymers containing 6 and 9 mol % sulfobetaine methacrylate functionality revealed two concentration regimes with a boundary at ~1.5 – 2.0 wt %, regardless of molecular weight. This transition occurred at an order of magnitude lower specific viscosity than the entanglement concentration (Ce) for poly(nBA), and correlated to the onset of fiber formation in electrospinning. Comparison to existing models for polymer solution dynamics showed closest agreement to Rubinstein's theory for associating polymers, in support of our hypothesis that zwitterionic interactions dominate solution dynamics. The effect of ionic liquid (IL) uptake on mechanical properties and morphology of zwitterionic copolymers was explored using 1-ethyl-3-methylimidazolium ethylsulfate (EMIm ES). Dynamic mechanical analysis and impedance spectroscopy revealed a significant change in properties above a critical uptake of ~10 wt % IL. X-ray scattering revealed a significant swelling of the ionic domains at 15 wt % IL, with a 0.3 nm-1 shift in the ionomer peak to lower scattering vector. Results indicated the water-miscible IL preferentially swelled ionic domains of zwitterionic copolymers. / Ph. D.

An A2 + B3 polymerization for the synthesis of hyperbranched polymers was altered using oligomeric precursors in place of either one or both of the monomer pairs to synthesize highly branched macromolecules. Unique topologies that are intermediates between long-chain branched and hyperbranched structures were obtained and the term "highly branched" was used to define these novel architectures. Various types of highly branched polymers, such as polyurethanes, poly(urethane urea)s, poly(ether ester)s, and poly(arylene ether)s were synthesized using the oligomeric A2 + B3 strategy. The molar mass of the oligomeric precursor permitted the control of the molar mass between branch points, which led to interesting macromolecular properties, such as superior mechanical performance to conventional hyperbranched polymers, disrupted crystallinity, improved processibility, and a multitude of functional end groups. Highly branched poly(urethane urea)s and polyurethanes exhibited microphase-separated morphologies as denoted by dynamic mechanical analysis. The similarity in soft segment glass transition behavior and mechanical properties of the branched systems with that of the linear analogues suggested these materials have considerable promise for a variety of applications. When a polycaprolactone triol was utilized as the B3 oligomer for the synthesis of highly branched polyurethane elastomers, the high degree of branching resulted in a completely amorphous soft segment, whereas the linear analogue with equivalent soft segment molar mass retained the crystallinity of polycaprolactone segment. Oligomeric A2 + B3 methodology was further utilized to tailor the degree of branching of poly(ether ester)s that were developed based on slow addition of dilute solution of poly(ethylene glycol) (PEG) (A2) to a dilute solution of 1,3,5-benzenetricarbonyl trichloride (B3) at room temperature in the presence of triethylamine. A revised definition of the degree of branching was proposed to accurately describe the branched poly(ether ester)s and the degree of branching decreased as the molar mass of the PEG diols was increased. Moreover, branched poly(arylene ether)s were prepared via a similar oligomeric A2 + B3 polymerization of phenol endcapped telechelic poly(arylene ether sulfone) oligomers (A2) and tris(4-fluorophenyl) phosphine oxide (B3) in solution. Highly branched poly(ether ester)s were also synthesized in the melt phase using the oligomeric A2 + B3 polymerization strategy. Melt polymerization effectively limited the cyclization reactions, which are common in A2 + B3 polymerizations in solution, and overcame the need for large amounts of polymerization solvent typical of A2 + B3 systems. Finally, a new family of telechelic polyester ionomers was synthesized based on phosphonium bromide salt end groups and branching allowed the incorporation of higher levels of ionic end groups compared to linear analogues. / Ph. D.

Novel proton exchange (PEM) and reverse osmosis (RO) membranes for application in fuel cell and water purification respectively were developed by synthesis and crosslinking of disulfonated biphenol-based poly (arylene ether sulfone)s (BPS). Crosslinking is a prospective option to reduce the water swelling and improve the dimensional stability of hydrophilic BPS copolymers. Several series of controlled molecular weight, phenoxide-endcapped BPS copolymers were synthesized via direct copolymerization of disulfonated activated aromatic halide monomers. The degree of disulfonation was controlled by varying the molar ratio of sulfonated to non-sulfonated dihalide monomers. The molecular weights of the copolymers were controlled by offsetting the stoichiometry between biphenol and the dihalides. Biphenol was utilized in excess to endcap the copolymers with phenoxide groups, so that the phenoxide groups could be further reacted with a suitable crosslinker. Several crosslinking reagents such as methacrylate, multifunctional epoxy, phthalonitrile and phenylethynyls were investigated. A wide range of crosslinking chemistries i.e. free radical (methacrylate), step growth (epoxy), heterocyclic (phthalonitrile) and acetylenic (phenylethynyl) was explored. The effects of crosslinking on network properties as functions of molecular weight and degree of disulfonation of copolymers, crosslinking time and concentration of crosslinker were studied. The crosslinked membranes were characterized in terms of gel fraction, water uptake, swelling, self-diffusion coefficients of water, proton conductivity, methanol permeability, water permeability and salt rejection. In general, all of the crosslinked membranes had lower water uptake and swelling relative to their uncrosslinked counterparts, and less water uptake and volume swelling were correlated with increasing gel fractions. It was possible to shift the percolation threshold for water absorption of BPS copolymers to a higher ion exchange capacity (IEC) value compared to that of the uncrosslinked copolymers by means of crosslinking. This reduced water uptake increased the dimensional stability of higher IEC materials and extended their application for potential PEM or RO membranes. The reduction in water uptake and swelling also increased the effective proton concentration, resulting in no significant change in proton conductivity of the membranes after crosslinking. The self-diffusion coefficients of water and methanol permeability decreased with crosslinking, indicating restricted water and methanol transport. Therefore an improvement in the selectivity (ratio of proton conductivity to water swelling or methanol permeability) of PEMs for application in either H2/air or direct methanol fuel cells was achieved by crosslinking. The epoxy crosslinked BPS copolymers also had significantly enhanced salt rejection with high water permeability when tested in for RO applications. Reductions in salt permeability with increasing crosslinking density suggested that crosslinking inhibited salt transport through the membrane. In addition to the random copolymers, two series of multiblocks endcapped with either a phenoxide-terminated hydrophilic unit or a hydrophobic unit were synthesized and crosslinked with a multifunctional epoxy. Besides the crosslinking study, the effect of sequence distributions of the hydrophilic and hydrophobic blocks in the multiblock copolymers was also investigated. Similar to randoms, crosslinked multiblocks had lower water uptake and swelling but comparable proton conductivities relative to their uncrosslinked analogues. / Ph. D.

The focus of this dissertation was to investigate the influence of sidechain structure and sidechain content on the morphology and physical properties of perfluorosulfonic acid ionomer (PFSA) membranes. One of the primary objectives was to characterize the thermomechanical relaxations for short sidechain PFSAs developed by 3M and Solvay, as well as a new multi-acid sidechain perfluoroimide acid ionomer (PFIA) from 3M. Partial neutralization experiments played a key role in systematically manipulating the strength of the electrostatic interactions between proton exchange groups on each sidechain, leading to the elucidation of the molecular-level motions associated with multiple thermal relaxations observed by dynamic mechanical analysis (DMA). Particularly, 3M PFSA and Solvay Aquivion lack an observable β-relaxation in the sulfonic acid-form that is observed in the long sidechain PFSA, Nafion. By varying the strength of the physically-crosslinked network through exchanging the proton on the sulfonic acid groups for large counterions, we were able to conclude that the shorter sidechain length and increase in ion content in the 3M PFSA and Solvay Aquivion serves to restrict the mobility of the polymer backbone such that the onset of segmental motions of the main chains is not observed at temperatures below the α-relaxation temperature, where destabilization of the physically crosslinked network occurs. As a complementary technique to DMA for probing the relaxations in PFSAs, we introduced a new pretreatment method for differential scanning calorimetry (DSC) measurements that uncover a thermal transition in H+-form 3M PFSA, Aquivion, and Nafion membranes. This thermal transition was determined to be of the same molecular origin as the dynamic mechanical α-relaxation temperature in H+-form PFSAs, and the β-relaxation temperature in tetrabutylammonium (TBA+)-form PFSAs. The thermomechanical relaxations in multi-acid sidechain 3M PFIA were also investigated. Interestingly, the additional acidic site on PFIA led to unexpected differences in thermal and mechanical properties, including the appearance of a distinct glass transition temperature otherwise not seen in PFSA ionomers. We utilized small-angle X-ray scattering (SAXS) studies to probe the differences in aggregate structure between the PFIA and PFSA membranes in order to uncover the morphological origin of the anomalous thermomechanical behavior in PFIA membranes. Larger aggregate structures for PFIA, compared to PFSA, incorporate intervening fluorocarbon chains within the aggregate, resulting in increased spacing between ions that reduce the collective electrostatic interactions between ions such that the onset of chain mobility occurs at lower temperatures than the α-relaxation for PFSA. The SAXS profiles of PFSAs showed two scattering features resulting from scattering between crystalline domains and ionic domains distributed throughout the polymer matrix. In order to fit the "ionomer peak" to models used for the PFIA and PFSA aggregate structure determination, we presented a method of varying the electron density of the ionic domains by using different alkali metal counterions as a tool to make the intercrystalline feature indistinguishable. This allows for isolation of the ionomer peak for better fits to scattering models without any interference from the intercrystalline peak. Lastly, an investigation of annealing PFSAs of different sidechain structures in the tetramethylammonium (TMA+) counterion form above their α-relaxation showed a profound crystalline-like ordering of the TMA+ counterions within the ionic domains. This ordering is maintained after reacidification and leads to improved proton conductivity, which indicates that this method can be used as a simple processing method for obtaining improved morphologies in proton exchange membranes for fuel cell applications. / Doctor of Philosophy / Hydrogen fuel cells offer an environmentally friendly, high efficiency method for powering vehicles, buildings, and portable electronic devices. At the center of a hydrogen fuel cell is a polymer membrane that contains ionic functionalities, which conduct hydrogen ions (protons) from the anode to the cathode while preventing conduction of electrons. The electrons travel through an external circuit to produce electricity, while the protons travel through the polymer membrane and meet with oxygen on the other side to produce water, the only byproduct of a hydrogen fuel cell. The efficiency of this process relies on the ability of the polymer membrane to conduct protons, and the lifetime of a fuel cell depends on the mechanical stability of this membrane. Perfluorosulfonic acid ionomers are good candidates for use as polymer membranes in hydrogen fuel cells due to their Teflon backbone that provides mechanical stability and their sulfonic acid functionalities that form channels for proton conduction. In this work, we probe the structure-property relationships of different perfluorosulfonic acid ionomers for use as fuel cell membranes. We focus on thermal analysis techniques to develop a fundamental understanding of the effect of chemical structure and sulfonic acid content on the temperature-induced mobility of the polymer chains in these ionomers. This mobility at elevated temperatures can be utilized to rearrange the morphological structure of perfluorosulfonic acid ionomer membranes in order to enhance proton conductivity and mechanical integrity.

This dissertation focuses on the fundamental understanding of liquid dynamics confined in polymer membranes. Such knowledge guides the development of better polymer membranes for practical applications and contributes to the general understanding of confined liquid dynamics in various nanoporous materials. First, we investigate the membrane transport by experimental measurements on a PFSA membrane and computer modeling of the confined liquid molecules. We probe the nano-scale environment in the ionomer membrane by determining the activation energy of diffusion. We notice two structural features of the PFSA membrane that dominate membrane transport. At relatively high hydrations, the nano-scale phase-separation creates bulk-like water in the ionomer membrane and prompts fast transport of mobile species. At relatively low hydrations, the nanoconfinement of the polymer matrix leads to the ordering of confined water and prompts a high energy barrier for transport. We then delve deeper into the confinement effect by molecular modeling of various nanoconfining geometries, including carbon nanotubes, parallel graphene sheets, and parallel rigid rods. We notice retarded water dynamics under hydrophobic confinement regardless of the geometry. We further investigate the confined water by determining the residence time of water around water, which evaluates the timescale of associations between water molecules. We learn that a decreasing confinement size prompts longer associations among water molecules. Further, we propose that the prolonged associations are responsible for the retarded water dynamics under hydrophobic confinement. Next, we turn our attention to the effect of interactions between mobile species (mostly water molecules) and a confining surface. In ionomer membranes, interactions between mobile species and the ionic groups dominate the water-surface interactions. We start by looking at water-ion interactions in bulk solutions. Using solutions at varying concentrations, we notice a temperature-concentration superposition behavior from diffusion coefficients of water molecules and ions in the solutions in both experimental and computational results. Observation of this superposition behavior in bulk solutions is unprecedented. The temperature-concentration superposition parallels the well-known time-temperature superposition. We are able to extract the offset of reciprocal temperature, which fits well to a Williams-Landel-Ferry type equation. The temperature-concentration superposition points to the new perspective that the effect of ions on water dynamics can be similar to the effect of lowering temperature. We further investigate the effect of ions by modeling ions/charges onto confining geometries. Remarkably, we reveal that the presence of ions can break the ordered water structure induced by confinement. The hydrophobic confinement prompts the ordering of water molecules, which leads to slower diffusion and higher activation energy. The presence of ions/charges on the confining surface has multiple effects on the dynamics of confined water. First, the ions associate strongly with neighboring water molecules while breaking the hydrogen-bonding network between water molecules. Second, the disruption of the hydrogen-bonding network leads to decreased activation energy of diffusion and enhanced water mobility. At relatively high ion density, the water-ion interactions overcome the structure-breaking effect and lead to retarded water diffusion. Overall, the studies presented in this dissertation augment our understanding of water transport in nanostructures by revealing the rich behavior of liquid-water dynamics under both hydrophobic and ionic confinement. / Doctor of Philosophy / Polymer separations membranes contribute to important applications such as fuel cells and water desalination. Optimizing the separation ability of polymer membranes improves their practical performance. The transport property of a polymer membrane depends on its nanoscale and microscale structures. This dissertation focuses on the nanoscale structure-transport relations in ionic polymer membranes. We utilize nuclear magnetic resonance techniques and molecular dynamics simulations to probe the transport properties. We investigate the effects of membrane nanostructure and water-ion interactions on the dynamics of confined water. Such knowledge not only guides the development of high-performance membranes but also contributes to the fundamental understanding of liquid dynamics in nanoporous materials.

The exploitation of the relationship between the chemical and physical properties of materials is the hallmark of advancing science throughout the world. The basic understanding of how and why molecules react and interact with each other in different environments allows for the discovery and implementation of new materials and devices that not only advance the state of human life but continually change the planet. The work described in this dissertation generally falls under three diverse categories: functionalization of fullerenes, investigation of host/guest interactions in solution, and the synthesis and characterization of ion containing polymers. The separation and functionalization of fullerenes is a recent and exciting area of research. The separation methods outlined are intended to increase the availability of endohedral metallofullerenes by decreasing their cost of production. Functionalized fullerene species were achieved through Bingel and Prato reactions to provide materials with novel functional groups. These materials may be further utilized in photovoltaic or other organic electronic devices. The characterization of noncovalent interactions between different molecules in solution is the focus of supramolecular chemistry. Isothermal Titration Calorimetry stands out as one of the best, among the many methods used to elucidate the characteristics of these systems. The binding of bis- imidazolium and paraquat guests with macrocyclic host molecules has been explored in this work. The measurements of the association constants for these systems will aid in the ongoing synthesis of new host/guest systems. Ion containing polymers were synthesized and characterized for their use in electroactive devices. Imidazolium containing polymers with bulky anions were synthesized on low glass transition polymer chains. These materials had enhanced ion conductivity and may eventually be used in electronic actuator materials. / Ph. D.