The foundational studies of this dissertation concern the characterization of segmented polyurethanes and polyureas synthesized without the use of chain extenders'molecules that are typically used to promote a microphase separated morphology that gives these materials their useful characteristics. Polyurethanes in which a single asymmetric diisocyanate comprising the whole of the hard segment were found to display poor microphase separation. Conversely, polyurethanes in which a single symmetric diisocyanate composed the hard segment were found to display good microphase separation. The more efficient packing of the symmetric hard segments also led to an increase in hard segment connectivity and hence higher values of storage moduli in these systems. When hydroxyl-terminated diisocyanates were replaced with amine-terminated diisocyanates, polyureas were formed. Here too, diisocyanate symmetry was found to play a key role with symmetric diisocyanates leading to better microphase separation. In addition, the polyurea materials displayed broader service temperature windows than their polyurethane counterparts as the relatively stronger bidentate hydrogen bonding replaced monodentate hydrogen bonding in these materials. A thread-like, microphase separated morphology was visually confirmed using atomic force microscopy. Other techniques such as ambient temperature tensile testing, and wide and small angle x-ray scattering were employed to confirm the presence of the microphase separated structure. The investigation into the effects of diisocyanate chemistry and its symmetry was broadened to incorporate non-chain extended polyurethane materials with different soft segment molecular weights, as well as polyurethanes that did contain chain extenders. Once again the effect of using symmetric versus asymmetric diisocyanates was evident in the structure–property behavior of these systems, with symmetric diisocyanates forming materials that displayed better microphase separation and more connectivity of their hard domains. Lastly, in a departure from the segmented copolymer area, a study was conducted into the influence of casting variables on the solid-state structure of synthetic polypeptide films based on glutamate chemistry. The effect of solvent evaporation was determined to play a key role in the morphology of these polypeptide films. Measured small angle light scattering patterns were compared to computer calculated patterns to reveal information about the structure, shape, and length scale of the polypeptide structure. / Ph. D.

Bio-inspired monomers functionalized with nucleobase or ionic group allowed synthesis of supramolecular polymers using free radical polymerization and controlled radical polymerization techniques. Comprehensive investigations for the structure-property-morphology relationships of these supramolecular polymers elucidated the effect of noncovalent interactions on polymer physical properties and self-assembly behaviors. Reverse addition-fragmentation chain transfer (RAFT) polymerization afforded acrylic ABC and ABA triblock copolymers with nucleobase-functionalized external blocks and a low-Tg central block. The hard-soft-hard triblock polymer architecture drove microphase-separation into a physically crosslinked hard phase in a low Tg matrix. Hydrogen bonding in the hard phase enhanced the mechanical strength and maintained processability of microphase-separated copolymers for thermoplastics and elastomers. A thermodynamically favored one-to-one stoichiometry of adenine and thymine yielded the optimal thermomechanical performance. Intermolecular hydrogen bonding of two thymine units and one adenine unit allowed the formation of base triplets and directed self-assembly of ABC triblock copolymers into remarkably well-defined lamellae with long-range ordering. Acetyl protected cytosine and guanine-containing random copolymers exhibited tunable cohesive strength and peel strength as pressure sensitive adhesives. Post-functionalization converted unprotected cytosine pendent groups in acrylic random copolymers to ureido-cytosine units that formed quadruple self-hydrogen bonding. Ureido-cytosine containing random copolymers self-assembled into nano-fibrillar hard domains in a soft acrylic matrix, and exhibited enhanced cohesive strength, wide service temperature window, and low moisture uptake as soft adhesives. A library of styrenic DABCO salt-containing monomers allowed the synthesis of random ionomers with two quaternized nitrogen cations on each ionic pendant group. Thermomechanical, morphological, and rheological analyses revealed that doubly-charged DABCO salts formed stronger ionic association and promoted more well-defined microphase-separation compared to singly-charged analogs with the same charge density. Bulkier counterions led to enhanced thermal stability, increased phase-mixing, and reduced water uptake for DABCO salt-containing copolymers, while alkyl substituent lengths only significantly affected water uptake of DABCO salt-containing copolymers. Step growth polymerization of plant oil-based AB monomer and diamines enabled the synthesis of unprecedented isocyanate-free poly(amide hydroxyurethane)s, the first examples of film-forming, linear isocyanate-free polyurethanes with mechanical integrity and processability. Successful electrospinning of segmented PAHUs afforded randomly orientated, semicrystalline fibers that formed stretchable, free-standing fiber mats with superior cell adhesion and biocompatibility. / Ph. D.

abstract: Polyurea is a highly versatile material used in coatings and armor systems to protect against extreme conditions such as ballistic impact, cavitation erosion, and blast loading. However, the relationships between microstructurally-dependent deformation mechanisms and the mechanical properties of polyurea are not yet fully understood, especially under extreme conditions. In this work, multi-scale coarse-grained models are developed to probe molecular dynamics across the wide range of time and length scales that these fundamental deformation mechanisms operate. In the first of these models, a high-resolution coarse-grained model of polyurea is developed, where similar to united-atom models, hydrogen atoms are modeled implicitly. This model was trained using a modified iterative Boltzmann inversion method that dramatically reduces the number of iterations required. Coarse-grained simulations using this model demonstrate that multiblock systems evolve to form a more interconnected hard phase, compared to the more interrupted hard phase composed of distinct ribbon-shaped domains found in diblock systems. Next, a reactive coarse-grained model is developed to simulate the influence of the difference in time scales for step-growth polymerization and phase segregation in polyurea. Analysis of the simulated cured polyurea systems reveals that more rapid reaction rates produce a smaller diameter ligaments in the gyroidal hard phase as well as increased covalent bonding connecting the hard domain ligaments as evidenced by a larger fraction of bridging segments and larger mean radius of gyration of the copolymer chains. The effect that these processing-induced structural variations have on the mechanical properties of the polymer was tested by simulating uniaxial compression, which revealed that the higher degree of hard domain connectivity leads to a 20% increase in the flow stress. A hierarchical multiresolution framework is proposed to fully link coarse-grained molecular simulations across a broader range of time scales, in which a family of coarse-grained models are developed. The models are connected using an incremental reverse–mapping scheme allowing for long time scale dynamics simulated at a highly coarsened resolution to be passed all the way to an atomistic representation. / Dissertation/Thesis / Doctoral Dissertation Mechanical Engineering 2020

Les polyuréthanes segmentés thermoplastiques (TPUs) sont des matériaux élastomères thermoplastiques qui couvrent une large gamme d’applications. Ces matériaux possèdent intrinsèquement une aptitude à la nano-structuration car ils présentent dans leur structure macromoléculaire une alternance de segments rigides et de segments souples thermodynamiquement immiscibles en dessous d’une certaine température (température de micro-mélange). Ainsi, en refroidissant à partir de l’état fondu, une micro-séparation de phase, dont la cinétique dépend de la température, se produit. De plus, l’application d’une déformation avant cette structuration modifie sa cinétique. Ainsi, en vue d’appréhender l’effet de la mise en oeuvre sur certaines propriétés de ces matériaux, il s’avère intéressant d’étudier l’influence de l’histoire thermomécanique sur la structuration. Cette étude repose sur l’observation du comportement de cristallisation et/ou de séparation de phase de cinq polyuréthanes commerciaux de nature chimique différente, en fonction de différentes conditions thermiques et mécaniques appliquées en milieu modèle ou en conditions de mise en oeuvre réelles. Les techniques utilisées sont principalement rhéologiques, rhéo-optiques et par diffusion de rayons X aux petits angles (SAXS). Ces différentes analyses permettent d’affirmer que les contraintes appliquées dans le fondu des matériaux avant leur solidification modifient de façon drastique la cinétique de structuration mais aussi leur morphologie résultante. En effet, une orientation particulière des entités structurées au sein des matériaux peut être engendrée par des contraintes appliquées en fonction de leur intensité. Cette morphologie résultante particulière joue également un rôle sur les propriétés mécaniques finales des matériaux. / Thermoplastic segmented polyurethanes are an important class of thermoplastic elastomers which cover a wide range of applications. These materials are multi-block copolymers composed of alternating “hard” and “soft” segments which are respectively below and above their glass transition temperature under ambient conditions. TPUs exhibit a twophase microstructure which arises from the thermodynamic incompatibility between the hard and soft segments. This microphase separation is often combined with the crystallization of either or both segments. The mechanical properties of these polymers will depend upon the overall multiblock length and the hard block sequence length and how they affect the material morphology. Our goal is to understand how the polyurethane final properties can be affected by the processing stresses (extrusion, injection…). In this scope, experiments were performed using a rheometer or an optical microscope coupled with a shearing hot stage. A preshear controlled treatment was applied and its effect on the material structuration was followed. These characterizations highlighted the enhancement of phase separation kinetics by the shear. For instance, for presheared samples, phase separation and/or crystallization of the hard segments occur ten times faster than for non-sheared ones. Moreover, SAXS experiments carried out on samples structured from several conditions illustrated perpendicular arrangements of crystalline domains perpendicularly to the flow direction. Finally, this particular morphology induced by shear modifies the materials final mechanical properties

Segmented copolymers are a commercially important class of materials that are utilized in a wide variety of applications. In these systems a relatively large number of variables such as backbone chemistry, segment molecular weight, and the overall molecular weight of the copolymer can be independently controlled to engineer materials with targeted properties. Such versatility also means that a large number of variables can influence the morphology and therefore, properties and performance of segmented copolymers. In this dissertation, the influence of selected variables on the solid state structure-property behavior of segmented poly(ether-block-amide), polyurethane, polyurethaneurea, and polyurea copolymers is explored. The specific variables which have been utilized singly or in conjunction with others are hard segment crystallizability, crystallization conditions, hard segment content, soft segment type and molecular weight, nature of hydrogen bonding, extent of inter-segmental hydrogen bonding, segment symmetry, and chain architecture. In poly(ether-block-amide)s, it was found that the morphology of both the crystalline and the amorphous phase depend upon the polyamide content of the sample and, as expected, the crystallization conditions. A comparison of polydimethylsiloxane based segmented polyurethanes with their polyurea counterparts demonstrated that for a constant hard segment content the soft segment molecular weight particularly governs the extent of microphase separation in these materials. The nature of hydrogen bonding, monodentate or bidentate, also strongly influences their mechanical response. Remarkably, the polyurea sample with a polydimethylsiloxane molecular weight of 7000 g/mol and a hard segment content of 25 wt % exhibited a remarkable service temperature window (for rubber-like behavior) of ca. 230°C (from -55°C to 175°C) whereas it was ca. 200°C wide (from -55°C to 145°C) for the equivalent polyurethane sample. The extremely high chemical incompatibility between the polydimethylsiloxane of sufficiently high molecular weight and urethane or urea segment is expected to generate a relatively sharp interface between the soft matrix and the dispersed hard domains. Therefore, a polyether co-soft segment was incorporated in a controlled manner along the chain backbone, which resulted in inter-segmental hydrogen bonding between the ether and the urea segments. The consequent segmental mixing gave rise to a gradient interphase, which led to a significant improvement in the tensile strength, and elongation at break in selected polydimethylsiloxane segmented polyurea copolymers. The importance of the hydrogen bonding network in model polyurethaneurea copolymers was also explored by utilizing LiCl as molecular probe. It has been demonstrated that hydrogen bonding plays an important role, over and above microphase separation, in promoting the long-range connectivity of the hard segments and the percolation of the hard phase through the soft matrix. The incorporation of hard segment branching in these polyurethaneurea also reduced the ability of the hard segments to pack effectively and establish long-range connectivity. The disruption of the percolated hard phase resulted in a systematic softening of the copolymers. The role of chain architecture in governing the structure/property/processing of segmented was also investigated by comparing highly branched segmented polyurethaneureas with their linear analogs. These copolymers were based on poly(propylene oxide) or poly(tetramethylene oxide) as the soft segments The highly branched copolymers utilized in this dissertation were able to develop a microphase morphology similar to their linear analogs. Particularly noteworthy, and surprising, was the observation of weak second order interference shoulder in the respective small angle X-ray scattering profiles of the highly branched samples based on poly(propylene oxide) of MW 8200 and 12200, indicating the presence of at least some level of long-range order of the hard domains in these samples. Tapping-mode atomic force microscopy phase images of these two samples clearly confirmed the small angle X-ray scattering results. In addition to the strain induced crystallization of the poly(tetramethylene oxide) MW 2000 g/mol based linear polyurethaneureas, the highly branched analog of this sample also exhibited similar behavior at ambient temperature and uniaxial deformation of ca. 400 % strain. Wide angle X-ray scattering confirmed the above observation. The reduced ability of the branched polymers to entangle resulted in slightly poorer mechanical properties, such as tensile strength, elongation at break, and stress relaxation as compared to their linear analogs. However, primarily due to their reduced entanglement density, the branched polyurethaneureas had significantly lower ambient temperature solution viscosity as compared to their linear polyurethaneurea analogs. Therefore, these highly branched polyurethaneureas can be more easily processed than the latter materials. Finally, it was demonstrated that non-chain extended segmented polyurethane and polyurea copolymers in which the hard segment is based on only a single diisocyanate molecule may well exhibit properties, such as the breadth of the service window, the average plateau modulus, stiffness, tensile strength, and elongation at break that are similar to chain extended segmented copolymers that possess distinctly higher hard segment content. A careful control of the hard segment symmetry and the nature of the hydrogen bonding is necessary to achieve such improved performance in the non-chain extended systems. Therefore, the results of this study provide new direction for the production of thermoplastic segmented copolymers with useful structural properties. / Ph. D.

The phase behavior of chiral block copolymers (BCPs*), namely, BCPs with at least one of the constituent block is formed by chiral monomers, is studied both experimentally and theoretically. Specifically, the formation of a unique morphology with helical sense, the H* phase, where the chiral block forms nanohelices hexagonally embedded in the matrix of achiral block, is investigated. Such unique morphology was first observed in the cast film of polystyrene-b-poly(L-lactide) (PS-b-PLLA) from a neutral solvent dichloromethane at room temperature with all the nanohelices being left-handed, which would switch to right-handed if the PLLA block changes to PDLA. Further studies revealed that such morphology only forms when the chiral PLLA block possesses certain volume fraction (from 0.32 to 0.36), and the molecular weight exceeds certain critical value (around 20,000 to 25,000 g/mol). Achiral phases such as lamellae, gyroid, cylinder, and sphere will form if the above criteria are not satisfied. Even though the unique H* phase has been extensively studied and utilized for many applications, many fundamental and important questions remain unanswered for such BCP* system. Specifically, how does the molecular level chirality transfer from the several-angstrom scale of the lactide monomer to the tens-of-nanometer size scale of the H* domain morphology? Why is the chirality transfer not automatic for this BCP* system? Is H* phase a thermodynamic stable or metastable phase? Are there other novel phases other than the H* phase that could form within the BCP* system? We aimed at providing answers to the abovementioned questions regarding the formation of chiral H* phase, which is no longer limited to the PS-b-PLLA/PDLA system. We divided our studies into both experimental and theoretical parts. In the experiments, we studied the effect of solvent casting conditions, including solvent removal rate and polymer-solvent interactions, on the formation of the H* phase in PS-b-PLLA/PDLA BCPs*. In addition, we monitored the morphological evolution during solvent casting using time-resolved x-ray scattering technique. We found that good solubility towards both PS and PLLA/PDLA blocks are required for the formation of the H* phase, and microphase separation has to happen prior to crystallization of chiral block. Most importantly, we found that crystalline ordering is not necessary for the H* phase formation. This result led us to propose melt-state twisted molecular packing as the underlying driving force for such helical phase to form, and began our work on the theory for BCPs*. First we built the theoretical tool by incorporating the orientational segmental interactions into the self-consistent field theory (SCFT) for BCPs. As a demonstration, we constructed the phase diagrams for one-dimensional (1D) and two-dimensional (2D) phases, for achiral BCPs with different orientational stiffness. We found that orientational stiffness could serve as another parameter to introduce asymmetry into BCP systems, in addition to conformational and architectural asymmetry. This model was further applied to study the phase behavior of BCPs*, and two phase diagrams were constructed. Another chiral phase, wavy lamellae (L* phase), was observed for BCPs*. The H* phase was found to be a thermodynamic stable phase, as long as the segregation strength ����and chiral strength ��! exceed certain critical values. Energetically favorable cholesteric texture was observed for the chiral segment packing inside the H* phase, which is believed to drive such unusual morphology to form. A simple geometrical argument based on bending of cylindrical microdomain and twisted packing of the bended microdomain can be given to explain the nonlinear chiral sensitivity of BCP* morphology, which further explains the non-automatic feature of chirality transfer in such system.

No description available.

Polysiloxanes represent a unique class of synthetic polymers, employing a completely inorganic backbone structure comprised of repeating –(Si–O)n– 'siloxane' main chain linkages. This results in an assortment of diverse properties exclusive to the siloxane bond that clearly distinguish them from the –(C–C)n– backbone of purely organic polymers. Previous work has elucidated a methodology for fabricating flexible and elastic crosslinked poly(dimethyl siloxane) (PDMS) constructs with high Mc through a simultaneous crosslinking and chain-extension methodology. However, these constructs suffer the poor mechanical properties typical of lower molecular weight crosslinked siloxanes (e.g. modulus, tear strength, and strain at break). Filled PDMS networks represent another important class of elastomers in which fillers, namely silica and siloxane-based fillers, impart improved mechanical properties to otherwise weak PDMS networks. This work demonstrates that proper silicon-based reinforcing agent selection (e.g. siloxane-based MQ copolymer nanoparticles) and incorporation provides a synergistic enhancement to mechanical properties, whilst maintaining a low viscosity liquid composition, at high loading content, without the use of co-solvents or heating. Rheological analysis evaluates the viscosity while photorheology and photocalorimetry measurements evaluate rate and extent of curing of the various MQ-loaded formulations, demonstrating theoretical printability up to 40 wt% MQ copolymer nanoparticle incorporation. Dynamic mechanical analysis (DMA) and tensile testing evaluated thermomechanical and mechanical properties of the cured nanocomposites as a function of MQ loading content, demonstrating a 3-fold increase in ultimate stress at 50 wt% MQ copolymer nanoparticle incorporation. VP AM of the 40 wt% MQ-loaded, photo-active PDMS formulation demonstrates facile amenability of photo-active PDMS formulations with high MQ-loading content to 3D printing processes with promising results. PDMS polyureas represent an important class of elastomers with unique properties derived from the synergy between the nonpolar nature, unusual flexibility, and low glass transition temperature (Tg) afforded by the backbone siloxane linkages (-Si-O)n- of PDMS and the exceptional hydrogen bond ordering and strength evoked by the bidentate hydrogen bonding of urea. The work herein presents an improved melt polycondensation synthetic methodology, which strategically harnesses the spontaneous pyrolytic degradation of urea to afford a series of PDMS polyureas via reactions at high temperatures in the presence of telechelic amine-terminated oligomeric poly(dimethyl siloxane) (PDMS1.6k-NH2) and optional 1,3-bis(3-aminopropyl)tetramethyldisiloxane (BATS) chain extender. This melt polycondensation approach uniquely circumvents the accustomed prerequisite of isocyanate monomer, solvent, and metal catalysts to afford isocyanate-free PDMS polyureas using bio-derived urea with the only reaction byproduct being ammonia, a fundamental raw ingredient for agricultural and industrial products. As professed above, reinforcement of polysiloxane materials is ascertained via the incorporation of reinforcing fillers or nanoparticles (typically fumed silica) or blocky or segmented development of polymer chains eliciting microphase separation, in order to cajole the elongation potential of polysiloxanes. Herein, a facile approach is detailed towards the synergistic fortification of PDMS-based materials through a collaborative effort between both primary methods of polysiloxane reinforcement. A novel one-pot methodology towards the facile, in situ incorporation of siloxane-based MQ copolymer nanoparticles into segmented PDMS polyureas to afford MQ-loaded thermoplastic and thermoplastic elastomer PDMS polyureas is detailed. The isocyanate-free melt polycondensation achieves visible melt dispersibility of MQ copolymer nanoparticles (good optical clarity) and affords segmented PDMS polyureas while in the presence of MQ nanoparticles, up to 40 wt% MQ, avoiding post-polymerization solvent based mixing, the only other reported alternative. Incorporation of MQ copolymer nanoparticles into segmented PDMS polyureas provides significant enhancements to modulus and ultimate stress properties: results resemble traditional filler effects and are contrary to previous studies and works discussed in Chapter 2 implementing MQ copolymer nanoparticles into chemically-crosslinked PDMS networks. In situ MQ-loaded, isocyanate-free, segmented PDMS polyureas remain compression moldable, affording transparent, free-standing films. / Master of Science / Polysiloxanes, also referred to as 'silicones' encompass a unique and important class of polymers harboring an inorganic backbone. Polysiloxanes, especially poly(dimethyl siloxane) (PDMS) the flagship polymer of the family, observe widespread utilization throughout industry and academia thanks to a plethora of desirable properties such as their incredible elongation potential, stability to irradiation, and facile chemical tunability. A major complication with the utilization of polysiloxanes for mechanical purposes is their poor resistance to defect propagation and material failure. As a result polysiloxane materials ubiquitously observe reinforcement in some fashion: reinforcement is achieved either through the physical or chemical incorporation of a reinforcing agent, such as fumed silica, or through the implementation of a chemical functionality that facilitates reinforcement via phase separation and strong associative properties, such as hydrogen bonding. This research tackles polysiloxane reinforcement via both of these strategies. Facile chemical modification permits the construction PDMS polymer chains that incorporate hydrogen bonding motifs, which phase separate to afford hydrogen bond-reinforced phases that instill vast improvements to elastic behavior, mechanical and elongation properties, and upper-use temperature. Novel nanocomposite formulation through the incorporation of MQ nanoparticles (which observe widespread usage in cosmetics) facilitate further routes toward improved mechanical and elongation properties. Furthermore, with growing interest in additive manufacturing strategies, which permit the construction of complex geometries via an additive approach (as opposed to conventional manufacturing processes, which require subtractive approaches and are limited in geometric complexity), great interest lies in the capability to additively manufacture polysiloxane-based materials. This work also illustrates the development of an MQ-reinforced polysiloxane system that is amenable to conventional vat photopolymerization additive manufacturing: chemical modification of PDMS polymer chains permits the installation of UV-activatable crosslinking motifs, allowing solid geometries to be constructed from a liquid precursor formulation.

No description available.

Following the discovery of the one-dimensional sequence of human DNA, much focus has been directed on microscopy and molecular techniques to learn about the spatial organization of chromatin in a 3D cell. The development of these powerful tools has enabled high-resolution, genome-wide analysis of chromosome structure under many different conditions. In this thesis, I focus on how the organization of interphase chromatin is established and maintained following mitosis. Mitotic chromosomes are folded into helical loop arrays creating short and condensed chromosomes, while interphase chromosomes are decondensed and folded into a number of structures at different length scales ranging from loops between CTCF sites, enhancers and promoters to topologically associating domains (TADs), and larger compartments. While the chromatin organization at these two very different states is well defined, the transition from a mitotic to interphase chromatin state is not well understood. The aim of this thesis is to determine how interphase chromatin is organized following mitotic chromosome decondensation and to interrogate factors potentially responsible for driving the transition. First, I determine the temporal order with which CTCF-loops, TADs, and compartments reform as cells exit mitosis, revealing a unique structure at the anaphase-telophase transition never observed before. Second, I test the role of transcription in reformation of 3D chromosome structure and show that active transcription is not required for the formation of most interphase chromatin features; instead, I propose that transcription relies on the proper formation of these structures. Finally, I show that RNA in the interphase nucleus can be degraded with only slight consequences on the overall chromatin organization, suggesting that once interphase chromatin structures are achieved, the structures are stable and RNA is only required to reduce the mixing of active and inactive compartments. Together, these studies further our understanding of how interphase structures form, how these structures relate to functional activities of the interphase cell, and the stability of chromatin structures over time.