Orientador: Roberto Usberti / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Agricola / Made available in DSpace on 2018-08-06T12:29:48Z (GMT). No. of bitstreams: 1 CavalcanteFilho_FranciscoNahum_M.pdf: 999790 bytes, checksum: b6fe814b4fe9db3c1d4b9f5196d0287a (MD5) Previous issue date: 2006 / Resumo: As sementes do gênero Brachiaria apresentam um mecanismo duplo de dormência, mais pronunciado em sementes recém colhidas, conduzindo a valores abaixo dos de viabilidade obtidos pelo teste de Tetrazólio e, deste modo, dificultando a tomada de decisões para o armazenamento, comercialização e fiscalização do comércio dessas sementes. Utilizando-se a tecnologia de detecção das constantes da equação de viabilidade de sementes, baseada em altas temperaturas de armazenamento e graus de umidade constantes, foi possível neste experimento isolar o efeito das temperaturas de 40, 50 e 65°C na liberação da dormência de sementes dos cultivares Marandu, Mulato 1 e Mulato 2 de Brachiaria brizantha, armazenadas com graus de umidade constantes, de 1,9 a 17,8%. As sementes apresentaram altos índices de dormência, detectada pelo teste de tetrazólio e liberada pela escarificação química e parcialmente pelo teste de envelhecimento acelerado. Não foram observadas diferenças para a velocidade de germinação (T50); entretanto ocorreram diferenças quanto ao número de sementes por grama. O padrão das isotermas de sorção e desorção foi semelhante para os cultivares. Os melhores resultados para liberação de dormência a 40°C foram obtidos nos graus de umidade de 9,5 e 8,5% para os cultivares Marandu e Mulato 1, respectivamente; a 50°C foram detectadas liberações de dormência em todos os graus de umidade testados e os melhores resultados foram obtidos para o cultivar Marandu (7,6 e 10,3%) e Mulato 1 (8,3%). As liberações de dormência a 65°C não foram tão evidentes em todos os graus de umidade testados. O cultivar Marandu apresentou maior armazenabilidade durante todo o experimento / Abstract: Brachiaria species normally show a double seed dormancy mechanism, mainly on fresh-harvest seeds, leading to germination percentages lower than those of viability detected by Tetrazolium test, so causing problems as to storage, trading and seed inspection activities. Using the methodology to detect the constants of the viability equation (high storage temperatures and fixed moisture contents) it was feasible in this research to isolate the effects of 40, 50 and 65°C on Brachiaria brizantha cultivars Marandu, Mulato 1 and Mulato 2 seed dormancy releasing, after storage at moisture contents ranging from 1.9 and 17.8%. Seed samples used presented high seed dormancy levels, detected by Tetrazolium test and it was released by chemical scarification and partially by accelerated ageing test. No statistical differences were observed as to speed of germination (T50); however, differences were detected as to number of seed per gram among cultivars. Sorption and desorption isotherm curves were similar for the cultivars. The best results of seed dormancy releasing at 40°C were achieved at 9.5 and 8.5% moisture content, for cultivars Marandu e Mulato 1 respectively; seed dormancy releasing results were obtained at 50°C for all moisture content studied and the best results were achieved for cultivars Marandu (7.6 e 10.3%) and Mulato 1 (8.3%). At 65°C seed dormancy releasing results were not clear. The cultivar Marandu presented higher storability than the others throughout the experiment / Mestrado / Tecnologia Pós-Colheita / Mestre em Engenharia Agrícola

Das Ziel der experimentellen Arbeit war die Untersuchung der Einflussfaktoren auf den Ertrag, die Saatgutqualität unter verschiedenen Lagerungsbedingungen sowie die Effizienz der Expression vonRamtillkraut (Guizotia abbysinica Cass.). In Feldversuchen wurden folgende Varianten untersucht, Sorten ‚Fogera‘ und ‚Kuyu‘, Saatgutaufwand von 5, 10, 15 kg ha-1, ein Stickstoffaufwand von 13, 23 und 33 kg ha-1, sowie eine differenzierte Wasserversorgung an zwei Standorten (Adet und Koga). In Adet wurde der höchste Saatgut Ertrag mit 1.384,60 kg ha-1 ermittelt, Erträgen in Koga (ohne Bewässerung) mit 1.064,72 kg ha-1 und 967,00 kg ha-1 (mit Bewässerung). Der höchste Ölgehalt wurde im Saatgut aus Koga (ohne Bewässerung) mit 41,54% ermittelt, gefolgt von Koga (mit Bewässerung) 39,59% und Adet mit 38,67%. Signifikante Unterschiede wurden zwischen den N-Aufwandmengen in Koga mit Bewässerung und Saatgutmengen in Adet ermittelt. Die Unterschiede bei den Fettsäuregehalten in Adet waren nicht signifikant. Der Alpha-Tocopherol Gehalt betrug 80 mg pro 100 g bei hoher Saatdichte und hoher N-Düngung. Hinsichtlich des Verfahrens des Ölpressens, wurde ein signifikanter Unterschied zwischen Effizienz und Temperatur ermittelt. Die Dauer der Konditionierung und die Vorschubgeschwindigkeit sind negative korreliert gleichfalls mit der Effizienz der Expression. Die Temperaturen von 70°C und 80°C zeigten keinen signifikanten Einfluss auf die Ölausbeute, dagegen war der der Einfluss von 90°C statistisch signifikant. / The aim of this study was to investigate factors influencing seed yield, postharvest handling, and the oil expression efficiency for nigerseed (Guizotia abbysinica Cass.). Based on field study on two varieties, two locations, three seed rates and three fertilizer rates the highest mean nigerseed yield was 1384.6 kg ha-1 at Adet location (rain fed) followed by location Koga (rain) with 1064.7 kg ha-1 and Koga (irrigation) with 967.0 kg ha-1 showing significant difference. The oil content by location was 41.54% for Koga (rain) followed by 39.59 and 38.67% for Koga (irrigation) and Adet (rain) respectively showing significant difference whereas the Ash content showed a reverse trend of oil content. Fatty acid composition did not show significant difference in any treatment. Significant mean alpha-tocopherol of 80 mg/100 g (70 to 89 mg/100 g) was attained for increasing seed and nitrogen rates. Based on two temperatures and seven relative humidities model evaluation and monolayer moisture content estimation, Guggenheim-Anderson-de Boer (GAB) models was found to best suit both varieties as compared to Brunauer-Emmet-Teller (BET), and modified Chung &Pfost. For oil expression efficiency, 90ºC seed conditioning showed significant effect compared to 80 and 70ºC however conditioning times and feed rates did not differ significantly.

The need for modern transportation systems together with the high demand for sustainable pavements under applied loads have led to a great deal of research on concrete pavements worldwide. Development of finite element techniques enabled researchers to analyse the concrete pavement under a combination of axle group loadings and environmental effects. Consequently, mechanistic approaches for designing of concrete pavements were developed based on results of finite element analyses. However, unpredictable failure modes of concrete pavements associated with expensive maintenance and rehabilitation costs have led to the use of empiricalmechanistic approach in concrete pavement design. Despite progressive knowledge of concrete pavement behaviour under applied loads, concrete pavements still suffer from deterioration due to crack initiation and propagation, indicating the need for further research. Cracks can be related to fatigue of the concrete and/or erosion of materials in sub-layers. Although longitudinal, midedge and corner cracks are the most common damage modes in concrete pavements, Austroads method for concrete pavement design was developed based on traditional mid-edge bottom-up transverse cracking introduced by Packard and Tayabji (1985). Research presented in this thesis aims to address the most common fatigue related distresses in concrete pavements. It uses comprehensive finite element models and analyses to determine the structural behaviour of concrete pavements under vehicular loads and environmental effects. Results of this research are supported by laboratory tests and an experimental field test. Results of this research indicate that the induced tensile stresses within the concrete pavement are significantly affected by vehicle speed, differential temperature gradient and loss of moisture content. Subsequently, the interaction between the above mentioned factors and concrete damage modes are discussed. Typical dynamic amplifications of different axle groups are presented. A new fatigue test setup is also developed to take into consideration effects of pavement curvature on fatigue life of the concrete. Ultimately, results of the research presented in this thesis are employed to develop a new guide for designing concrete pavements with zero maintenance of fatigue damage.

Hårdgörning av trä syftar till att göra materialet hårdare. Detta går att åstadkomma genom komprimering, det komprimerade materialet tenderar dock att återgå mot sin ursprungsform då materialet utsätts för fukt om ingen låsning sker. Låsningen kan ske mekaniskt i en treskiktskonstruktion som motverkar träets fuktrörelser. Dessa skivor har dock visat sig vara instabila och tidigare försök har uppvisat deformationer i form av kupning. Denna undersökning syftar till att utreda förutsättningarna för att använda komprimerad asp samt att ta fram underlag för framtagning av en kommersiell produkt. Praktiska tester har genomförts för att studera hårdhet, återfjädring och densitet hos det komprimerade virket. Vidare har treskiktsskivor tagits fram för att testa om det går att få en stabil konstruktion genom att variera tjockleken på spärrskiktet. Även skillnader i acklimatiseringstid och fuktkvotens inverkan för virkets återfjädring har studerats. Resultaten visar på att aspens hårdhet efter komprimering blir i samma nivå som bok och ask, en låg fuktkkvot vid komprimering av materialet ger en låg återfjädring, komprimerat material har en längre acklimatiseringstid till jämviktsfuktkvot och materialet går att låsa tvärs fiberriktningen i en treskiktskonstruktion. / To make wood harder it can be densified. This can be achieved by compression, the compressed material tends to return to the original shape when it is exposed to moisture fluxations and if no form of fixation occurs. The fixation can be done mechanically in a three-layer panel construction which reduce movements in the timber. These panels have been found to be unstable and previous attempts have shown deformations in form of cupping. This study aims to evaluate the conditions for using compressed aspen wood, and to provide a basis for development of a commercial product. Practical tests have been conducted to study hardness, springback and density of the compressed wood. In addition, three-layer panels have been developed to test whether it is possible to have a stable construction by varying the thickness of the buttom layer. Differences in acclimatisation time and the moisture contents effect on the springback has aslo been studied. The results show that the hardness of aspen wood after compression is in equal levels with beech and ashes, a low moisture contet provides a low springback, compressed timber have a longer time for acclimatisation and it is possible to fixate the material in the direction across the grain in a three-layer panel construction.

<p>Hårdgörning av trä syftar till att göra materialet hårdare. Detta går att åstadkomma genom komprimering, det komprimerade materialet tenderar dock att återgå mot sin ursprungsform då materialet utsätts för fukt om ingen låsning sker. Låsningen kan ske mekaniskt i en treskiktskonstruktion som motverkar träets fuktrörelser. Dessa skivor har dock visat sig vara instabila och tidigare försök har uppvisat deformationer i form av kupning. Denna undersökning syftar till att utreda förutsättningarna för att använda komprimerad asp samt att ta fram underlag för framtagning av en kommersiell produkt.</p><p>Praktiska tester har genomförts för att studera hårdhet, återfjädring och densitet hos det komprimerade virket. Vidare har treskiktsskivor tagits fram för att testa om det går att få en stabil konstruktion genom att variera tjockleken på spärrskiktet. Även skillnader i acklimatiseringstid och fuktkvotens inverkan för virkets återfjädring har studerats.</p><p>Resultaten visar på att aspens hårdhet efter komprimering blir i samma nivå som bok och ask, en låg fuktkkvot vid komprimering av materialet ger en låg återfjädring, komprimerat material har en längre acklimatiseringstid till jämviktsfuktkvot och materialet går att låsa tvärs fiberriktningen i en treskiktskonstruktion.</p> / <p>To make wood harder it can be densified. This can be achieved by compression, the compressed material tends to return to the original shape when it is exposed to moisture fluxations and if no form of fixation occurs. The fixation can be done mechanically in a three-layer panel construction which reduce movements in the timber. These panels have been found to be unstable and previous attempts have shown deformations in form of cupping. This study aims to evaluate the conditions for using compressed aspen wood, and to provide a basis for development of a commercial product.</p><p>Practical tests have been conducted to study hardness, springback and density of the compressed wood. In addition, three-layer panels have been developed to test whether it is possible to have a stable construction by varying the thickness of the buttom layer. Differences in acclimatisation time and the moisture contents effect on the springback has aslo been studied.</p><p>The results show that the hardness of aspen wood after compression is in equal levels with beech and ashes, a low moisture contet provides a low springback, compressed timber have a longer time for acclimatisation and it is possible to fixate the material in the direction across the grain in a three-layer panel construction.</p>