This dissertation explores the different ways to create thin film-based biosensors that are capable of rapid and label-free detection of cortisol, a non-specific biomarker closely linked to stress, within the physiological range of 10pM to 10 uM. Increased cortisol levels have been linked to stress-related diseases, such as chronic fatigue syndrome, irritable bowel syndrome, and post-traumatic stress disorder. It also plays a role in the suppression of the immune system as well. Therefore, accurate measurement of cortisol in saliva, serum, plasma, urine, sweat, and hair, is clinically significance to predict physical and mental diseases. In this dissertation, thin film-based electrochemical immunosensors were fabricated using a self-assembled monolayer (SAM) functionalized by cortisol specific antibodies to detect cortisol at 10 pM level sensitivities in the presence of a redox probe. The fabricated electrochemical cortisol immunosensors were able to detect cortisol in human saliva samples and the outcomes were validated using the standard Enzyme Linked Immuno Sorbent Assay (ELISA) technique. With the aim of improving signal amplification and label-free cortisol detection, copper nanoparticles were incorporated on screen-printed carbon electrodes (SPCE) for the fabrication of electrochemical cortisol immunosensor. This SPCE-based sensor showed a sensitivity of 4.21µA/M and the limit of detection 6.6nM. Both the SAM and SPCE-based immunosensors were not thermally stable due to the instability of antibodies at room temperature. To address this issue, an antibody-free immunosensor was fabricated. Molecular Imprinted Polymer (MIP) was used to template the target cortisol molecule. The MIP-based sensing platform was prepared using polypyrrole, a thermally stable conducting polymer. The conductivity of the polymer ensured good electrical performance. The polypyrrole-based MIP was synthesized by means of electrochemical polymerization and was used to detect cortisol within the physiological range at room temperature. MIP-based sensors exhibited the detection limit of 1 pM, and were cost-effective, easy to fabricate, temperature stable, and reusable. The sensing performance of the resulting sensors was comparable to those of commercially available technologies, such as ELISA. Aiming to perform cortisol sensing at point-of-care (POC), an Extended Gate Field Effect Transistor (EGFET) was integrated with a developed MIP cortisol sensor. The as developed MIP-EGFET sensor was used to detect the cortisol concentration in the range of 1 pM to 100 nM. A few of the major advantages of the developed sensor are its ability to provide a direct readout and simpler electronic systems, which are necessary for miniaturized Point of Care devices.

Les chiffres des statistiques du cancer colorectal en France et dans le mondemontrent la nécessité de développement de plateformes technologiques plus rapides,sensibles et spécifiques pour assurer le diagnostic du cancer. Un diagnostic rapide va ainsiaider à améliorer l’état de santé et réduire le temps d’attente des résultats qui peut être ungrand facteur de stress pour les patients. L’analyse des biomarqueurs dans le sang, lesurines et autres fluides corporels est l’une des méthodes appliquées pour la détectionprécoce de la maladie. Dans le cadre de ce projet des nucléosides urinaires ont été identifiéscomme biomarqueurs pour le cancer colorectal. Financée par l’Agence Nationale de laRecherche (ANR), à travers le projet CancerSensor (programme TECSAN), cette thèse s’estdéroulée au sein de l’équipe MDA (Microsystèmes de Détection Acoustique) du laboratoireIMS. Dans le cadre de ce projet, nous avons proposé une solution technologique dedétection et de suivi de biomarqueurs du cancer colorectal. Notre choix de la stratégie dedétection s’est porté sur les polymères à empreintes moléculaires comme élément dereconnaissance des biomarqueurs. Celui-ci sera associé à un transducteur acoustique àondes de Love mis au point lors de travaux précédents au sein de l’équipe MDA. Lebiocapteur ainsi développé va cibler les nucléosides mis en évidence pour le cancercolorectal. / Colorectal cancer statistics in France and all over the world demonstrate theneed for fast, sensitive and specific technological platforms development for cancerdiagnosis. A rapid diagnosis will improve the patients’ health status and reduce the resultswaiting time which could be a great stress factor. Biomarkers analysis in blood, urine andother body fluids is recognized as one of the applied methods for early cancer detection. Inframe of this project, urinary nucleosides have been identified as colorectal cancerbiomarkers. Funded by the National Research Agency (ANR), through the cancer sensorproject (TECSAN program), this thesis was carried out in IMS laboratory. Hence, a colorectalcancer biomarkers detection and monitoring technological solution has been proposed. Inour detection strategy, Molecularly Imprinted Polymers (MIP) has been identified asbiomarker recognition element. The MIP layer has been associated to Love Wave acoustictransducer. This biosensor will sense the identified colorectal cancer nucleosides.

The research described in this thesis contributes to the development of new strategies facilitating advanced understanding of the fundamental principles governing selective recognition of molecularly imprinted polymers (MIPs) at a molecular level for the rational optimization of biomimetic materials. The nature of non-covalent interactions involved in the templating process of molecularly imprinted polymers based on the self-assembly approach were investigated with a variety of analytical techniques addressing molecular level interactions. For this purpose, the concerted application of IR and 1H-NMR spectroscopy enabled studying the complexation of the template molecules 2,4-dichlorophenoxyacetic acid, quercetin, and o-, m-, and p-nitrophenol with a variety of functional monomers in the pre-polymerization solution by systematically varying the ratio of the involved components. In aqueous and non protic porogenic solvents, information on the interaction types, thermodynamics, and complex stoichiometry was applied toward predicting the optimum imprinting building blocks and ratios. Molecular dynamics simulations of 2,4-dichlorophenoxyacetic acid and its interactions with the functional monomer 4-vinylpyridine in aqueous and aprotic explicit solvent allowed demonstrating the fundamental potential of computer MD simulations for predicting optimized pre-polymerization ratios and the involved interaction types. The obtained results clearly demonstrate that the application of rapid IR/NMR pre-screening methods in combination with molecular modeling strategies is a promising strategy towards optimized imprinting protocols in lieu of the conventionally applied labor intensive and time-consuming trial-and-error approach. Furthermore, HPLC characterization of the produced MIPs compared to control polymers enabled a systematic approach to imprinting based on advanced understanding of the factors governing the formation of high-affinity binding sites during the polymerization. In addition, the importance of the combination of size, shape, and molecular functionalities for the selective recognition properties of MIPs was investigated. MIPs for the mycotoxins deoxynivalenol and zearalenone and for the antioxidant quercetin were applied as separation materials for advanced sample preparation in beverage analysis. The obtained results demonstrated the potential of MIPs for rapid one-step sample clean-up and pre-concentration from beverages such as wine and beer.

This thesis aimed at elaborating an optical sensor to detect molecules in a biological fluid. Two steroids and a xenobiotic were identified as biomarkers released in some body fluids: cyproterone acetate, cortisol and 2,4-dichlorophenoxyacetic acid respectively. On one hand, detection was performed by Molecularly Imprinted Polymers (MIPs). These tailor-made synthetic receptors display numerous qualities that foster their integration in sensors. MIPs were therefore developed against the targeted analytes. Formulation optimization was led thanks to experimental designs. On the other hand, optical transduction was made possible thanks to the structuring of a polymer into a photonic crystal. Opals were manufactured with a new process suitable for large scales and were used to mold MIPs in inverse opals. Thus, submicron structures of the polymer are responsible for the color of the sensor. A change of color is triggered by the recognition of the analyte by the polymer (upon swelling). Polymers studied displayed sufficient swelling observed by spectrophotometry. Finally, the work of this thesis consisted in elaborating polymer formulations and their integration in a sensor so as to detect an analyte with direct, rapid and unobtrusive means.

This thesis describes the development of highly selective fiber optic sensors using molecularly imprinted polymers (MIPs) as recognition elements associated with fluorescence for detection. Additionally, we extended the study to the development of other MIP-based optical sensors and sensing methods. MIPs are synthetic biomimetic receptors possessing specific cavities designed for a target molecule. Produced by a templating process at the molecular level, MIPs are capable of recognizingand binding target molecules with selectivities and affinities comparable to those of natural receptors. Compared to biological recognition elements, MIPs are more stable, cheaper and easier to integrate into standard industrial fabrication processes. Hence, MIPs have become interesting alternatives to biomolecules as recognition elements for biosensing. In the first part of this thesis (Chapter 2), MIPs were synthesized by in-situ laser-induced photopolymerization in only a few seconds, as a micrometer-sized tip at the extremity of a telecommunication optical fiber. Photonic and physico-chemical parameters were optimized to tailor the properties of the polymer micro-objects. Gold nanoparticles were incorporated into the MIP microtip for signal enhancement. To prove the efficiency of the sensor, initial studies were performed with a MIP templated with N-carbobenzyloxy-L-phenylalanine (Z-L-Phe) and the fluorescent amino acid derivative dansyl-L-phenylalanine as analyte. The fluorescence was collected either externally at the tip level by an optical fiber connected to a spectrofluorimeter or by collection of the fluorescent signal re-emitted into the fiber through the second arm of a Y-shaped bifurcated fiber. The fluorescent analyte could be detected in the low nM concentrations. In order to monitor nonfluorescent analytes, a naphthalimide-based fluorescent monomer was incorporated into the MIP during its synthesis; fluorescence enhancement was observed when analyte binding occurs. Using this system, the sensor containing a MIP specific for the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D), could detect and quantify this analyte at concentrations as low as 2.5 nM. The signaling MIP-based sensor was also applied to analytes of interest for food safety and biomedical applications, such as the mycotoxin citrinin and the sphingolipid, D-erythro-sphingosine-1-phosphate. In the second part of the thesis (Chapter 3), a different type of fiber optic sensor: cheap, fast and made for "single-use", was developed by using 4-cm long disposable polystyrene evanescent wave optical fiber waveguides. The coating of the MIP was either performed ex-situ, by dip-coating the fiber in a suspension of MIP particles synthesized beforehand, or in-situ by evanescent-wave photopolymerization directly on the fiber. The resulting fiber optic sensor could detect 2,4-D in the low nM range and demonstrated specific and selective recognition of the herbicide over its structural analogues and other non-related carboxyl-containing analytes. Additionally, we demonstrated the versatility of the system by applying the evanescent wave fiber optic sensor to detect citrinin, a mycotoxin, by simply coating the waveguide with a MIP specific for citrinin. This type of technology could possibly be extended to detect other carboxyl-containing analytes, as long as a specific MIP for the concerned analyte is available. In parallel, the technique of evanescent-wave photopolymerization was used for the synthesis of signaling MIP microdots on continuous and nanostructured gold films. This study lays the foundations for future development of plasmonic MIP nanosensors and microchips. In the last part of the thesis (Chapter 4), an innovative sensing method, based on the use of MIPs and analysis by fluorescence polarization, was developed in order to allow the fast and directquantification of analytes in food and environmental samples.

This thesis describes the development of highly selective fiber optic sensors using molecularly imprinted polymers (MIPs) as recognition elements associated with fluorescence for detection. Additionally, we extended the study to the development of other MIP-based optical sensors and sensing methods. MIPs are synthetic biomimetic receptors possessing specific cavities designed for a target molecule. Produced by a templating process at the molecular level, MIPs are capable of recognizingand binding target molecules with selectivities and affinities comparable to those of natural receptors. Compared to biological recognition elements, MIPs are more stable, cheaper and easier to integrate into standard industrial fabrication processes. Hence, MIPs have become interesting alternatives to biomolecules as recognition elements for biosensing. In the first part of this thesis (Chapter 2), MIPs were synthesized by in-situ laser-induced photopolymerization in only a few seconds, as a micrometer-sized tip at the extremity of a telecommunication optical fiber. Photonic and physico-chemical parameters were optimized to tailor the properties of the polymer micro-objects. Gold nanoparticles were incorporated into the MIP microtip for signal enhancement. To prove the efficiency of the sensor, initial studies were performed with a MIP templated with N-carbobenzyloxy-L-phenylalanine (Z-L-Phe) and the fluorescent amino acid derivative dansyl-L-phenylalanine as analyte. The fluorescence was collected either externally at the tip level by an optical fiber connected to a spectrofluorimeter or by collection of the fluorescent signal re-emitted into the fiber through the second arm of a Y-shaped bifurcated fiber. The fluorescent analyte could be detected in the low nM concentrations. In order to monitor nonfluorescent analytes, a naphthalimide-based fluorescent monomer was incorporated into the MIP during its synthesis; fluorescence enhancement was observed when analyte binding occurs. Using this system, the sensor containing a MIP specific for the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D), could detect and quantify this analyte at concentrations as low as 2.5 nM. The signaling MIP-based sensor was also applied to analytes of interest for food safety and biomedical applications, such as the mycotoxin citrinin and the sphingolipid, D-erythro-sphingosine-1-phosphate. In the second part of the thesis (Chapter 3), a different type of fiber optic sensor: cheap, fast and made for "single-use", was developed by using 4-cm long disposable polystyrene evanescent wave optical fiber waveguides. The coating of the MIP was either performed ex-situ, by dip-coating the fiber in a suspension of MIP particles synthesized beforehand, or in-situ by evanescent-wave photopolymerization directly on the fiber. The resulting fiber optic sensor could detect 2,4-D in the low nM range and demonstrated specific and selective recognition of the herbicide over its structural analogues and other non-related carboxyl-containing analytes. Additionally, we demonstrated the versatility of the system by applying the evanescent wave fiber optic sensor to detect citrinin, a mycotoxin, by simply coating the waveguide with a MIP specific for citrinin. This type of technology could possibly be extended to detect other carboxyl-containing analytes, as long as a specific MIP for the concerned analyte is available. In parallel, the technique of evanescent-wave photopolymerization was used for the synthesis of signaling MIP microdots on continuous and nanostructured gold films. This study lays the foundations for future development of plasmonic MIP nanosensors and microchips. In the last part of the thesis (Chapter 4), an innovative sensing method, based on the use of MIPs and analysis by fluorescence polarization, was developed in order to allow the fast and directquantification of analytes in food and environmental samples.

Dans le domaine des capteurs chimiques et biologiques, les besoins toujours croissants en termes de sensibilité, de rapidité et de sélectivité de l’analyse nécessitent le développement de couches sensibles transductrices de plus en plus performantes. Dans ce contexte et dans l’optique de pouvoir détecter de petites molécules non électroactives, telles que l’atrazine (ATZ), nous avons conçu, caractérisé et développé des couches sensibles constituées de polymères conducteurs fonctionnalisés à empreintes moléculaires (MICP) et les avons intégrées au sein de capteurs électrochimiques et gravimétriques. A partir de solutions d’acétonitrile contenant de l’ATZ, molécule empreinte en interaction avec des monomères fonctionnels dérivés du thiophène (FM = TMA, TAA, EDOT, TMeOH ou Th), différents polythiophènes FM-MICP de structures et de fonctionnalités différentes ont été électrosynthétisés sur substrats d’or et utilisés pour la détection de l’ATZ. Nous avons montré que les propriétés de reconnaissance des FM-MICP résultaient de la présence en leur sein d’empreintes moléculaires, fonctionnalisées par les résidus FM, qui conservaient la mémoire géométrique et fonctionnelle des molécules cibles. Néanmoins, une adsorption non-spécifique se produit systématiquement à la surface des couches sensibles et affecte par conséquent la sélectivité de la reconnaissance. Les techniques de caractérisation de surface employées nous ont permis de mettre en évidence l’influence de l’épaisseur et des propriétés structurales des couches sensibles sur l’efficacité de la détection. En outre, nous avons montré que du fait de la porosité de la couche polymère, le processus de reconnaissance se produisait en volume. Par ailleurs, des mesures électrochimiques corrélées à des calculs semi-empiriques ont permis de démontrer l’influence de la nature de FM d’abord sur la force de l’interaction ATZ-FM au sein de la solution de pré-polymérisation, ensuite sur le nombre d’empreintes moléculaires et enfin sur la sensibilité des FM-MICP vis-à-vis de l’ATZ. La couche TAA-MICP, qui présente un faible seuil de détection (10-9 mol L-1) ainsi qu’une large gamme dynamique (10-8 à 10-4 mol L-1), est la plus performante des couches sensibles puisqu’elle offre le meilleur compromis entre une détection spécifique de l’ATZ relativement élevée et une adsorption non-spécifique relativement faible. Enfin, le TAA-MICP a été utilisé comme couche sensible au sein d’un capteur électrochimique original à ondes acoustiques de surface (ESAW) dans l’optique de réaliser des mesures gravimétriques et électrochimiques couplées et simultanées. / In the field of chemical and biological sensors, the increased need for better sensitivity, faster response and higher selectivity during an analysis process, requires the development of more and more efficient transducing sensing layers. In this context, and with the aim to detect small non-electroactive molecules, such as atrazine (ATZ), we designed, characterized and developed sensing layers constituted by functionalized Molecularly Imprinted Conducting Polymers (MICP) and we integrated them into electrochemical and gravimetrical sensors. Starting from acetonitrile pre-polymerization media containing ATZ as template molecules in the presence of thiophene-based functional monomers (FM, namely TMA, TAA, EDOT, TMeOH or Th), differently functionalized and structurally different polythiophene-based FM-MICP films were electrosynthesized onto gold substrates and used for ATZ detection. The sensing properties of FM-MICP layers were shown to result from the presence in their backbones of pre-shaped FM-functionalized imprinted cavities which keep the memory of the targets. Nevertheless, non-specific adsorption onto the surface of the sensing layers takes place systematically, which affects the selectivity of the recognition process. Thanks to surface characterization techniques, we highlighted the influence of the thickness and of the structural properties of the layers on the efficiency of the recognition process. Besides, this latter was shown to operate in the bulk of the polymer matrixes thanks to layers porosity. On another hand, electrochemical measurements correlated with semi-empirical calculations demonstrated the influence of the nature of FM on the strength of the ATZ-FM interaction in the pre-polymerization medium, and then on the number of ATZ molecular imprints and on the sensitivity towards ATZ of the FM-MICP layers. We showed that TAA-MICP, which presents a low limit of detection (10-9 mol L-1) and a large dynamic range (10-8 to 10-4 mol L-1), is the best sensing layer since it offers the best compromise between high level of specific detection of ATZ and low level of non-specific adsorption. Finally, TAA-MICP was used as sensitive layer in an original Electrochemical Surface Acoustic Wave sensor (ESAW) which enabled simultaneous coupled gravimetric and electrochemical measurements.

Ce rapport de thèse présente l’étude de la technologie des empreintes moléculaires pour le développement de polymères spécifiques et sélectifs envers des biomarqueurs urinaires nucléosidiques du cancer colorectal chez l’Homme. L’objectif principal était de développer des polymères à empreintes moléculaires compatibles aux milieux aqueux en utilisant la technique du « dummy template », l’approche non-covalente and la polymérisation radicalaire en masse. Nous nous sommes concentrés principalement sur la qualité des polymères à partir de leur formulation, c’est-à-dire la spécificité et la sélectivité. Cela a été mené de façon empirique d’abord par la production de poudres issues de polymères monolithiques. Ainsi, pour atteindre les objectifs fixés, nous avons exploré le choix de la molécule « template ». Une étude de modèle est présentée au chapitre 3, en utilisant trois nucléosides 2’,3’,5’-peracétylés comme molécule empreinte dans une approche « dummy template ». Ensuite, en s’appuyant sur la connaissance apportée par le chapitre 3, nous avons développé des polymères à empreintes moléculaires (MIPs) sélectifs de la pseudouridine et de la N7-méthylguanosine dans les chapitres 4 et 5, respectivement, en utilisant la 2’,3’,5’-tri-O-acétylpseudouridine et la 2’,3’,5’-tri-O-acétylguanosine comme templates. L’étude de la rétention des nucléosides recherchés et de leurs analogues structuraux menée par chromatographie en phase liquide et par analyse frontale a permis de déterminer la capacité des différents polymères et de connaître leur comportement dans de l’urine synthétique. Finalement, pour évaluer la possible application de ces polymères dans un échantillon réel, l’urine humaine, la technique de l’extraction sur phase solide à empreintes moléculaires ou MISPE a été développée. Ainsi, une purification sélective des biomarqueurs cibles, tels que la pseudouridine et la N7-méthylguanosine, dans des échantillons d’urines a pu être démontrée. / This thesis report presents the exploration of molecularly imprinted polymer (MIP) technology for developing of a sensitive and selective polymers used in urinary nucleoside biomarker recognition. The main goal was to develop water compatible MIPs prepared by a “dummy template” imprinting technology, using a non-covalent approach and radical-polymerization in bulk. We were focusing mostly on the polymer quality in the formulation (rigidity, stability and repeatability). This was chosen empirically first by production of powders from monolithic MIP. Thus, to accomplish the stated goals, we have explored the choice of the template molecule. A model study presented by Chapter 3, using three 2’3’5’-tri-Operacylateduridine nucleosides as templates in a “dummy” template approach was first developed. Then, applying the knowledge of the type of template choice, we developed a selective MIP for recognition of pseudouridine and N7-methylguanosine in the studies presented in Chapter 4 and Chapter 5 respectively. By using 2’3’5’-tri-O-acetylpseudouridine and 2’3’5’-tri-O-acetylguanosine as templates. Chromatographic methods like HPLC retention and frontal analysis were used in the interest of determining the binding capacity of synthesized polymers, and the behavior in synthetic urine. Finally, to evaluate the possible application of these polymers in urine, molecularly imprinted solid phase extraction (MISPE) was developed. Selective purification of urine samples containing pseudouridine and N7-methylguanosine obtained in the end.

Submitted by JEFFERSON HONORIO FRANCO null (jeffersonhfranco@gmail.com) on 2016-12-01T15:16:17Z No. of bitstreams: 1 TESE FINAL-IMPRESSÃO CD.pdf: 4568825 bytes, checksum: 666b30b163102c69eb93110502678419 (MD5) / Approved for entry into archive by Felipe Augusto Arakaki (arakaki@reitoria.unesp.br) on 2016-12-05T12:50:59Z (GMT) No. of bitstreams: 1 franco_jh_dr_araiq_par.pdf: 1149871 bytes, checksum: 4c942fc016c94499d690f6474dda7078 (MD5) / Made available in DSpace on 2016-12-05T12:50:59Z (GMT). No. of bitstreams: 1 franco_jh_dr_araiq_par.pdf: 1149871 bytes, checksum: 4c942fc016c94499d690f6474dda7078 (MD5) Previous issue date: 2016-11-21 / Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / Corantes sintéticos do tipo azo têm sido um assunto de grande preocupação ambiental devido ao potencial genotóxico e mutagênico dos produtos de biotransformação. Deste modo, nos últimos anos a consequência da ingestão destes corantes presentes na agua potável servida à população é discutida por diversos autores. Este estudo avalia a ação de microssomas de fígado de rato, enzimas redutoras produzidas pela bactéria Escherichia coli (E. coli) e nitroredutase imobilizada na biotransformação de três corantes dispersos que possuem grupos azo, Disperse Red 73 (DR 73), Disperse Red 78 (DR 78) e Disperse Red 167 (DR 167). A técnica de Espectrofotometria de absorção molecular na região do Uv- visível, Cromatografia Líquida de Alta Eficiência com detector de arranjo de diodos (CLAE-DAD) e Cromatografia líquida acoplada à espectrometria de massas (LC-MS/MS) foram técnicas usadas para identificar os principais produtos gerados após os processos de degradação dos corantes. Polímeros de impressão molecular magnéticos (MMIPs) foram investigados usando reações de polimerização por precipitação para pré-concentração do corante DR 73, juntamente com a degradação por fotoeletrocatálise e subsequente análise dos produtos por LC-MS/MS. Os estudos in vitro do metabolismo de biotransformação dos corantes têxteis com microssoma de fígado de rato mostraram que as reações ocorreram preferencialmente no grupo azo e nitro dos corantes, indicando a redução destes grupos pelas enzimas do citocromo P-450. Foram obtidos dois produtos de degradação para cada corante após reação com a bactéria E. coli; o corante DR 73 originou os produtos 3-((4-aminofenil)(etil)amino)propanitrila e 4-nitroanilina, os produtos 3-((4-aminofenil)(etil)amino)propanitrila e 2-cloro-4-nitroanilina foram obtidos após reação com o corante DR78 e o DR 167 originou dimetil 3,3`-((3-acetamido-4aminofenil)azanediyl)dipropanoato e 2-cloro-4-nitroanilina, indicando a clivagem do grupo azo, possivelmente, pela enzima azoredutase, produzida pela bacteria. A enzima nitroredutase, imobilizada em partículas magnéticas modificadas com tosil, mostrou que a redução dos corantes ocorreu preferencialmente no grupo nitro, enquanto que a enzima livre no meio reacional resultou em mais de um produto de biotransformação para cada corante, atuando em mais de um sítio da molécula, comprovando a eficácia da imobilização enzimática para estudos de biotransformação e formação de produtos majoritários. A mutagenicidade dos corantes foi avaliado pelo ensaio de Salmonella/microssoma realizado nas estirpes TA 98 e TA 100, com e sem S9. De acordo com este ensaio, DR 73 foi o mais mutagênico. O MMIP para o corante DR 73 apresentou excelentes valores de religação (16 mg g−1 e 6 mg g−1, para MMIP e MNIP, respectivamente) indicando que o polímero molecularmente impresso formou cavidades específicas para retenção do corante. Através dos resultados obtidos por LCMS/MS, observou-se 100% de degradação do corante em apenas 60 min de tratamento via fotoeletrocatálise para soluções mais diluidas do mesmo, comprovando a eficiência da técnica na degradação de poluentes. Sendo assim, estes resultados sugerem que o MMIP mostrou uma excelente especificidade e seletividade para o corante DR 73 e uma técnica promissora na captação de corantes mutagênicos de águas superficiais, com grande potencial de aplicação e exploração na pré-concentração antes do tratamento. Além disso, a redução destes corantes por sistemas biológicos representa uma grande preocupação ambiental devido ao aumento da genotoxicidade para os seres vivos, em especial a seres humanos, produzindo compostos nocivos, tais como aminas condenadas pela Agência Internacional de Pesquisa sobre o Câncer. / Synthetic azo dyes have been a matter of great concern due to the genotoxic and mutagenic potential of the products originating from azo dye biotransformation. Thus, in recent years the result of the intake of these dyes present in drinking water supplied to a population is discussed by several authors. This work evaluates the action of rat liver microsomes, reducing enzymes produced by the Escherichia coli (E. coli) and nitroreductase immobilized on biotransformation of three disperse dyes bearing azo groups, namely Disperse Red 73 (DR 73), Disperse Red 78 (DR 78), and Disperse Red 167 (DR 167). UV-Vis spectrophotometry, high-performance liquid chromatography with diode array detector (HPLC-DAD), and liquid chromatography coupled to mass spectrometry (LC-MS/MS) were techniques used to identify the main products generated after the process degradation of dyes. Magnetic molecularly imprinted polymers (MMIPs) were investigated using precipitation polymerization reactions for preconcentration of the dye DR 73, together with the photoelectrocatalysis degradation and subsequent analysis of the products by LC-MS/MS. In vitro studies of biotransformation metabolism of textile dyes with rat liver microsome showed that the reactions occur preferentially in the group of azo and nitro dyes, indicating the reduction of these groups by enzymes of the cytochrome P-450. There were obtained two degradation products for each dye after reaction with E. coli; the dye DR 73 gave the product 3 - ((4-aminophenyl) (ethyl) amino) propanitrila and 4-nitroaniline, the product 3 - ((4-aminophenyl) (ethyl) amino) propanitrila and 2-chloro-4-nitroaniline were obtained after reaction with the dye DR78 and DR 167 gave 3,3`-dimethyl-((3-acetamido-4-aminophenyl) azanediyl) dipropanoato and 2chloro-4-nitroaniline; indicating cleavage of the azo group, possibly by azoredutase enzyme produced by bacteria. The nitroreductase enzyme immobilized on modified magnetic particles Tosyl showed that the reduction of dyes occurred preferentially in the nitro group, while the free enzyme in the reaction medium resulted in more than a product of biotransformation for each dye, acting in more than one site of the molecule, proving the efficacy of enzyme immobilization for biotransformation studies and formation of major products. The mutagenicity of the dyes was evaluated by the Salmonella/microsome assay performed on strains TA 98 and TA 100, with and without S9. According to this assay, DR 73 was the most mutagenic. The MMIP to the dye DR 73 showed excellent rebinding values (16 mg g−1 and 6 mg g−1, for MMIP and MNIP, respectively) indicating that the molecularly imprinted polymer formed cavities for specific dye retention. Through the results obtained by LC-MS/MS, it was observed 100% dye degradation in 60 min treatment for more dilute solutions thereof, proving the efficiency of technique in pollutant degradation. Thus, these results suggest that MMIP showed excellent specificity and selectivity for the dye DR 73 and a promising technique in capturing mutagenic dyes of surface water, with great potential for application and operation in the pre-concentration before treatment. Moreover, the reduction of these dyes by biological systems is a major environmental concern due to increased of genotoxicity for living beings, especially humans, producing harmful compounds, such as condemned amines by the International Agency for Research on Cancer.

The present work describes the development of a highly sensitive and selective molecularly imprinted electrochemical sensor for 4-nitrophenol detection. A glassy carbon electrode was modified with vyniltrimethoxisylane (VTMS) and multiwall carbon nanotubes (MWCNT). The introduced nanocomposite increased surface area and active sites for electron transfer. When the sillane is used on the synthesis, it is named MIS (molecularly imprinted silane) and NIS (non-imprinted silane) when the analyte is not on the synthesis. For those silane films characterization, it was used the scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and fourier transform infrared spectroscopy (FTIR). This sensor showed its best performance in 0.1 mol L-1 phosphate buffer solution, at pH 7.0. After optimizing the operational conditions, this sensor provided a linear response range for 4-NP from 0.1 up to 100 μmol L-1 and good parameters as LOD, LOQ and sensibility, 0.03 μmol L-1, 0.1 μmol L-1 and 1.4×10-2 A mol L-1 respectively. Furthermore, the MIS/PNP sensor exhibited good stability with adequate reproducibility and accuracy. / No presente trabalho é descrito o desenvolvimento de um sensor eletroquímico altamente sensível e seletivo baseado na tecnolgia dos Polímeros Impresso Molecularmente para detecção de 4-nitrofenol. Um eletrodo de carbono vítreo foi modificado com viniltrimetoxisilano (VTMS) e nanotubos de carbono de pardes múltiplas (MWCNT). O nanocompósito de carbono introduzido aumentou a área superficial e os locais ativos para transferência de elétrons. No método sol-gel quando um sillano é usado na síntese, é denominado MIS (Molecular Imprinted Silane) e NIS (non-imprinted Silane) quando o analito não está na síntese. Para a caracterização dos filmes de silanos utilizou - se a microscopia eletrônica de varredura (MEV), a análise termogravimétrica (TGA) e a espectroscopia de infravermelho por transformação de Fourier (FTIR). Este sensor apresentou o seu melhor desempenho em solução tampão fosfato 0,1 mol L-1, a pH 7,0. Depois de otimizado as condições operacionais, este sensor proporcionou uma faixa de resposta linear para o 4-nitrofenol de 0,1 a 100 μmol L-1 e bons parâmetros como limite de detecção, quantificação e sensibilidade de 0,03 μmol L-1, 0,1 μmol L-1 e 1,4×10-2 A mol L-1 respectivamente. Além disso, o sensor MIS/4-nitrofenol apresentou boa estabilidade com reprodutibilidade e precisão adequadas.