Recent advances in nanofabrication techniques have opened up new avenues and numerous possible applications in both nanoscale electrochemistry and analytical nanoscience by enabling the fabrication of reproducible nanoelectrodes with different new geometries. Nanoelectrodes exhibit advantages including enhanced mass transport, higher current densities, improved signal-to-noise ratios, and lower ohmic drop. In this dissertation, the use of nanoelectrodes in the electrochemical response properties investigations or in the spectroelectrochemical studies is the unifying factor among all the chapters. First (in Chapter 4), we presented a direct comparison between the electrochemical characteristics of two finite nanoelectrodes arrays with different geometries: 6 × 6 recessed nanodiscs and nanorings microarrays. Using computational methods, it was demonstrated that the electrode geometry’s parameters have a drastic influence on the mass transport properties of the nanoelectrodes. The results presented here are the first combination of experimental and numerical studies that elucidate the transport on nanoring electrode arrays. The comparison of the electrochemical behavior between nanostructures using full 3D simulations is also unique. Second, we have provided a comprehensive numerical study on the redox cycling performance properties of a 6 × 6 recessed nanorings-ring electrode array configuration. The simulation results were in good agreement with the experimental data. After validating the model against experiments, a comprehensive computational investigation revealed avenues to optimize the performance of the structure in terms of geometric parameters and scan rates. The second half of this dissertation is comprised of the spectroelectrochemical studies. The combination of surface plasmon resonance with electrochemistry presents new paths to investigateredox reaction events at the electrode surface since it brings an additional dimension to the classical electrochemical approaches. Third, we have reported a novel active plasmonic device based on a new switching mechanism for the nanohole electrodes array to bridge between photonics and electronics at nanoscales. The inner surfaces of the nanohole electrodes in the array were coated with an electroconductive polymer, polypyrrole, (PPy). Then, it was shown that light transmitted through the PPy- modified nanohole electrodes can be easily tuned and controled by applying an external potential. We were also able to switch on and off the transmitted light intensity through the modified nanohole arrays by potential steps, demonstrating the potential of this platform to be incorporated into optoelectronic devices. Finally, we have fabricated larger area plasmonic periodic nanopillar 3D electrodes using a rapid, high-throughput, and cost-effective approach: the laser interference lithography. Then, the electrochemical behavior of these electrodes was investigated both experimentally and computationally. The properties were ‘compared with a flat electrode with an equivalent geometric area. Afterward, we have successfully probed the changes in the concentration of a reversible redox pair near the electrode surface induced by various applied potentials, in an in-situ EC-SPR experiment. / Graduate

La chimiluminescence électrogénérée (ECL) est une technique analytique puissante exploitée pour la détection autant au niveau industriel que dans le domaine de la recherche scientifique ou du diagnostic clinique. La sensibilité élevée et la bonne sélectivité de cette technique font de l'ECL une méthode analytique de choix pour un large éventail d'applications, dont la plus importante est son utilisation commerciale dans un grand nombre de tests immunologiques à base de billes fonctionnalisées. Dans cette thèse, nous avons cherché à étudier le phénomène ECL et son application pour le développement de nouvelles techniques analytiques.Dans la première partie de ce travail, nous utilisons les techniques d'imagerie pour étudier les mécanismes ECL se produisant sur les billes utilisées pour les tests immunologiques. La cartographie de la réactivité au niveau d'une seule microparticule fonctionnalisée avec un complexe de ruthénium fournit une nouvelle stratégie visant à tester l'efficacité du co-réactif et montre des effets optiques associés de focalisation.Dans la deuxième partie, la conception d'un test immunologique pour la détection de l'anti-transglutaminase pour le diagnostic de la maladie coeliaque est présentée en utilisant des ensembles de nanoélectrodes comme plates-formes bioélectroanalytiques. Nous avons également étudié les caractéristiques de l'ECL générée par des réseaux de nanoélectrodes dopées au bore-diamant en tant que matériaux prometteurs pour des applications biologiques ainsi que l'efficacité ECL de deux co-réactifs sur ces réseaux.L'électrochimie bipolaire est un processus sans contact que nous avons exploité pour contrôler le mouvement d'objets conducteurs exposés à un champ électrique en l'absence de contact ohmique direct. Dans la troisième partie de ma thèse, nous présentons l'ECL couplée à l'électrochimie bipolaire pour le suivi d’objets autonomes luminescents. Nous avons élargi ce concept à la détection enzymatique dynamique de glucose en utilisant l'émission de lumière ECL comme signal analytique. / Electrogenerated chemiluminescence (ECL) is a powerful analytical technique exploited for clinical, industrial and research applications. The high sensitivity and good selectivity, makes ECL a tool-of-choice analytical method for a broad range of assays, most importantly for a large number of commercialized bead-based immunoassays. In the present thesis, we aimed to study the ECL phenomenon and its application in development of new analytical methods.In the first part of this work, we used an imaging technique to investigate the ECL mechanisms operating in bead-based assays. Spatial reactivity mapping at the level of a single functionalised bead provides a new strategy to test the co-reactant efficiency and shows associated optical focusing effects.In the second part, the design of a novel anti-transglutaminase ECL immunoassay for celiac disease diagnostic is shown using nanoelectrode ensembles as bioelectroanalytical platforms. We also studied the characteristics of ECL generated by arrays of boron-doped-diamond nanoelectrodes (BDD NEAs) as a promising materials for bioapplications. The ECL efficiency of two co-reactants at BDD NEAs was investigated.Finally, bipolar electrochemistry is a ‘‘wireless’’ process that was exploited for the controlled motion of conductive objects exposed to an electric field in the absence of direct ohmic contact. In the third part of the thesis, we report ECL coupled to bipolar electrochemistry for tracking the autonomous trajectories of swimmers by light emission. We further expanded this concept for dynamic enzymatic sensing of glucose concentration gradient using ECL light emission as an analytical readout.

La structuration et la fonctionnalisation de réseaux de fibres optiques ont été utilisées afin de réaliser différents capteurs électrochimiques et luminescents. Ce type de support permet de concevoir des capteurs capables de détecter à distance dans un milieu confiné, difficilement accessible ou dangereux. Deux capteurs pour la détection du mercure cationique (Hg2+) sont décrits dans cette thèse. Le premier utilise un dérivé de la rhodamine, qui est lié de façon covalente à la surface en verre du réseau, par silanisation. Le signal fluorescent de cette sonde est augmenté en présence de mercure ce qui permet de le quantifier. Le second capteur combine l’électrochimie sur ces réseaux de fibres optiques, grâce à une fine couche conductrice déposée à sa surface. Le réseau est ensuite modifié avec un complexe de Ruthénium(II), qui peut être électropolymérisé par l’intermédiaire de la fonction cyclopentadithiophène (CPDT). La détection du mercure est alors réalisée par électrochimiluminescence (ECL), qui est collectée à distance, grâce aux propriétés électro-modulables du film polymère. Les réseaux de fibres optiques nanostructurés ont également été utilisés pour la réalisation d’une sonde SECM, présentant un réseau dense de nanoélectrodes collectives. La réalisation d’un tel outil utilise le positionnement basé sur les forces de cisaillement et peut être utilisé pour la structuration de surfaces conductrices ou isolantes par SECM. / The structuration and the functionalisation of optical fiber bundles have been used to design different optical and electrochemical sensors. The use of these tools allows the realisation of sensors for remote detection in a confined environment, which may be dangerous or not easily accessible. Two sensors for the detection of inorganic mercury (Hg2+) are described in this thesis. The first sensor uses a rhodamine derivative, which is covalently functionalized on the surface of the glass optical fibers by silanisation. The fluorescent signal of this probe increases in presence of mercury, which allows its quantification. The second sensor uses the combination of electrochemistry on the optical fiber bundle, thanks to a thin conductive layer deposited on its surface. The bundle is then modified by electropolymerisation of a Ruthenium (II) complex through the cyclopentadithiophene (CPDT) moiety. The detection of mercury is then realised by elecrogenerated chemiluminescence (ECL), which is collected through the optical fiber bundle, thanks to the optical properties of the polymer film. The nanostructured array of optical fibers has also been used to create a new SECM probe composed of a dense nanoelectrode array. Such a tool is obtained through Shearforce positioning and can be used for the structuration of conductive or insulating surfaces by SECM.

Most biological experiments are performed on an ensemble of cells under the assumption that all cells are identical. However, recent evidence from single cells studies reveals that this assumption is incorrect. Individual cells within the same generation may differ dramatically, and these differences have important consequences for the health and function of the entire living body. I have used Scanning Ion Conductance Microscopy (SICM) for imaging and analysis of topographical change of single cell membrane, which is difficult to be revealed by optical microscopes. Morphological change in the fixed and live HeLa cell membrane during endocytosis of conjugated polymer nanoparticles was studied. Results demonstrated SICM is a powerful tool to study the interaction between nanoparticle and cell membrane during internalization of nanoparticles through the membrane. This research can improve our fundamental understanding of cellular behavior and will be helpful for drug delivery applications. Based on conventional SICM, we have developed a novel method to simultaneous map the topography and potential distributions of the single living cells membranes. At the first step, multifunctional nanopipettes (nanopore/nanoelectrode) have been fabricated and characterized. To demonstrate the potential sensing capability and understand the mechanism, I measured the ionic current and local electric potential change during translocation of 40 nm charged gold nanoparticles. Our results reveal the capability of the multifunctional probe for the highly sensitive detection of the ionic current and local electrical potential changes during the translocation of the charged entity through the nanopore. From the potential change, we revealed the dynamic assembly of GNPs before entering the nanopore. The experimental results are also nicely explained by the finite element method based numerical simulation results. At the second step, I have measured the surface potential of living cell membrane at selected locations. Very recently, I have obtained results to show that we can map the extracellular membrane potential distribution of the complicated living cell membrane with sub-micron spatial resolution.This new imaging technique can help biologist to explore the extracellular potential distribution of varieties of cells quantitatively.These studies will have impacts on several biomedical applications such as regenerative repair and cancer treatment.

No description available.

Es besteht enormes Interesse den Stofftransport in nanoskaligen Systemen zu verstehen und selektiv zu steuern, um analytische und synthetische Anwendungen zu entwickeln, aber auch um die physiologischen Prozesse lebender Zellen zu entschlüsseln. Im Rahmen dieser Arbeit wurde der Einfluss der elektrochemischen Doppelschicht an ausgewählten nanoskaligen Elektrolytsystemen untersucht. Die Gleichrichtung von Ionenströmen (engl. Ionic Current Rectification ICR) in Nanoporen mit einer Oberflächenladung äußert sich in einer gekrümmten Strom-Spannungs-Kurve. Die Überlappung von innerem und äußerem Potential ist dabei hinsichtlich der Ionenverteilung und somit der Porenleitfähigkeit einander verstärkend oder gegenläufig. Auf Grundlage dieses Mechanismus wurde die Gleichrichtung bei einem sehr großen Verhältnis von Porenöffnung zu Debye-Länge erklärt. Ferner wurde mittels der eingeführten relativen Leitfähigkeit κ´ die verschiedenen Leitfähigkeitszustände in Abhängigkeit der Elektrolytkonzentration und Temperatur sichtbar gemacht und Implikationen für Sensoranwendungen wie z.B. dem resistiven Pulszähler zur Partikelanalyse abgeleitet. Es wurde ein numerisches Modell basierend auf dem Poisson-Nernst-Planck-Gleichungssystem entwickelt, um die Translokation eines Nanopartikels durch eine konische Nanopore bei einer geringen Leitsalzkonzentration zu beschreiben. Neben dem klassischen Volumenausschluss-Effekt tritt zusätzlich ein Gleichrichtungseffekt (ICR-Effekt) in der Pore auf. Eine Analyse zur Entflechtung von Partikelgröße und Partikelladung aus der Pulshöhe und Pulsform wurde erfolgreich durchgeführt. Wie der Stofftransport durch eine Oberflächenladung auf dem umgebenden Material einer Nanoelektrode beeinflusst wird, wurde anhand des voltammetrischen Verhaltens diskutiert. An sehr kleinen Elektroden (< 10 nm) ist demnach der Einfluss der elektrochemischen Doppelschicht auf die Strom-Spannungs-Kurve besonders groß und kann auch bei Vorliegen eines hohen Leitsalzüberschusses nicht vernachlässigt werden. In leitsalzfreien Elektrolyten sind die gefundenen Effekte so deutlich, dass sie auch an größeren Elektroden experimentell zweifelsfrei festgestellt worden sind. / There is an enormous interest in understanding and selectively controlling the material transport in nanoscale systems to develop analytical and synthetic applications, but also to decipher the physiological processes of living cells. Within this thesis, the influence of the electrochemical double layer on selected nanoscale electrolyte systems was studied. Ionic Current Rectification (ICR) in nanopores carrying a surface charge manifests itself in a non-linear current-voltage-curve. The overlap of interior and exterior potential is cumulative or opposing with regard to the ion distribution and therefore the pore conductivity. Based on this mechanism, ICR for very large ratios of pore size and Debye length was explained. Furthermore, the different conducting states as a function of electrolyte concentration and temperature were visualized by introducing the relative conductivity κ´ and hence implications for sensor applications such as the resistive pulse sensor have been deduced. A numerical model based on the Poisson-Nernst-Planck-equations was developed to describe the translocation of a nanoparticle through a conical nanopore at a low electrolyte concentration. An additional rectification effect (ICR effect) occurs in the pore beside the conventional volume exclusion effect. An analysis was successfully performed to deconstruct the particle size and particle charge from the pulse height and shape. The material transport is affected by a surface charge on the shrouding material of nanoelectrodes as it was discussed by means of the voltammetric behaviour. The influence of the electrochemical double layer on the current-voltage-curve is particularly large at very small electrodes (< 10 nm) and cannot be neglected even at a high excess of supporting electrolyte. The observed effects were pronounced in unsupported electrolytes, so that they could be clearly detected experimentally at even larger electrodes.

Es besteht enormes Interesse den Stofftransport in nanoskaligen Systemen zu verstehen und selektiv zu steuern, um analytische und synthetische Anwendungen zu entwickeln, aber auch um die physiologischen Prozesse lebender Zellen zu entschlüsseln. Im Rahmen dieser Arbeit wurde der Einfluss der elektrochemischen Doppelschicht an ausgewählten nanoskaligen Elektrolytsystemen untersucht. Die Gleichrichtung von Ionenströmen (engl. Ionic Current Rectification ICR) in Nanoporen mit einer Oberflächenladung äußert sich in einer gekrümmten Strom-Spannungs-Kurve. Die Überlappung von innerem und äußerem Potential ist dabei hinsichtlich der Ionenverteilung und somit der Porenleitfähigkeit einander verstärkend oder gegenläufig. Auf Grundlage dieses Mechanismus wurde die Gleichrichtung bei einem sehr großen Verhältnis von Porenöffnung zu Debye-Länge erklärt. Ferner wurde mittels der eingeführten relativen Leitfähigkeit κ´ die verschiedenen Leitfähigkeitszustände in Abhängigkeit der Elektrolytkonzentration und Temperatur sichtbar gemacht und Implikationen für Sensoranwendungen wie z.B. dem resistiven Pulszähler zur Partikelanalyse abgeleitet. Es wurde ein numerisches Modell basierend auf dem Poisson-Nernst-Planck-Gleichungssystem entwickelt, um die Translokation eines Nanopartikels durch eine konische Nanopore bei einer geringen Leitsalzkonzentration zu beschreiben. Neben dem klassischen Volumenausschluss-Effekt tritt zusätzlich ein Gleichrichtungseffekt (ICR-Effekt) in der Pore auf. Eine Analyse zur Entflechtung von Partikelgröße und Partikelladung aus der Pulshöhe und Pulsform wurde erfolgreich durchgeführt. Wie der Stofftransport durch eine Oberflächenladung auf dem umgebenden Material einer Nanoelektrode beeinflusst wird, wurde anhand des voltammetrischen Verhaltens diskutiert. An sehr kleinen Elektroden (< 10 nm) ist demnach der Einfluss der elektrochemischen Doppelschicht auf die Strom-Spannungs-Kurve besonders groß und kann auch bei Vorliegen eines hohen Leitsalzüberschusses nicht vernachlässigt werden. In leitsalzfreien Elektrolyten sind die gefundenen Effekte so deutlich, dass sie auch an größeren Elektroden experimentell zweifelsfrei festgestellt worden sind. / There is an enormous interest in understanding and selectively controlling the material transport in nanoscale systems to develop analytical and synthetic applications, but also to decipher the physiological processes of living cells. Within this thesis, the influence of the electrochemical double layer on selected nanoscale electrolyte systems was studied. Ionic Current Rectification (ICR) in nanopores carrying a surface charge manifests itself in a non-linear current-voltage-curve. The overlap of interior and exterior potential is cumulative or opposing with regard to the ion distribution and therefore the pore conductivity. Based on this mechanism, ICR for very large ratios of pore size and Debye length was explained. Furthermore, the different conducting states as a function of electrolyte concentration and temperature were visualized by introducing the relative conductivity κ´ and hence implications for sensor applications such as the resistive pulse sensor have been deduced. A numerical model based on the Poisson-Nernst-Planck-equations was developed to describe the translocation of a nanoparticle through a conical nanopore at a low electrolyte concentration. An additional rectification effect (ICR effect) occurs in the pore beside the conventional volume exclusion effect. An analysis was successfully performed to deconstruct the particle size and particle charge from the pulse height and shape. The material transport is affected by a surface charge on the shrouding material of nanoelectrodes as it was discussed by means of the voltammetric behaviour. The influence of the electrochemical double layer on the current-voltage-curve is particularly large at very small electrodes (< 10 nm) and cannot be neglected even at a high excess of supporting electrolyte. The observed effects were pronounced in unsupported electrolytes, so that they could be clearly detected experimentally at even larger electrodes.