Together with the world economic growth is the increasing of energy generation demand. However, the upgrade of world power production capability could affect the environment negatively. Even the clean and renewable sources, such as hydroelectricity and wind powers have socio-economic and environmental disadvantages. For example, the required flooded area for a hydro power plant construction could devastate entire forests, and the installation of a wind farm power plant could affect migratory rotes of birds and generate high levels of noise. Hence, for the balancing of advantages and disadvantages of each power generation source, it is necessary to diversify, which requires investments in new power sources. In this context, the energy generation in the ocean is highlighted. The first point concerning the ocean energy is that there is no need of population removal from the installation area, such as the onshore based methods and the second point is that most of the population is concentrated in coastal areas. Therefore the production occurs near to the demand, decreasing the costs with energy distribution. The two main methodologies for harassing energy from oceans are based on gravity waves and in tides. And since the tidal cycles are governed mainly by the gravitational interaction between oceans, Moon and Sun, they are easily predictable, which increases the reliability of such systems. These works explores methodologies to analyse the power generation from a single axial tidal current turbine through a Steady State RANS methodology. Are discussed the effects of flow directionality, inlet velocity profile and turbulence levels and the results are compared with an experimental scheme. It is proposed an alternative methodology for free surface modelling in the CFD analysis. The usual methodology, VOF, it is based on a homogeneous, biphasic approach which requires an additional mesh refinement and is computationally expensive. This new methodology introduces an elastic wall approach in the free surface region in which the stiffness is calculated to provide the same restoring effect as gravity. In general, the results for open domain matched with the experimental results, validating the numerical model and the confined domain has shown a higher power and thrust coefficients if compared with the open domain, which is in accordance with the actuator disk theory approach. The elastic free surface presented convergence problems related to high Froude numbers and therefore to high deformations. However, a simulation with 10% of the original inlet velocity was performed, achieving reasonable results for both power and thrust coefficients evaluation. / O crescimento econômico mundial e o aumento na demanda pela geração de energia andam juntos. No entanto, uma maior capacidade de produção de energia poderia afetar negativamente o meio ambiente. Mesmo as fontes limpas e renováveis, como a hidrelétrica e a eólica acarretam em impactos socioeconômicos e ambientais. Por exemplo, a construção de uma usina hidrelétrica demanda uma imensa área alagada que pode devastar florestas inteiras e a instalação de uma usina eólica pode afetar a migração de certas espécies de pássaros e produzir altos níveis de barulho. Portanto, para equilibrar as vantagens e desvantagens devidas a cada meio de produção de energia, é necessária a diversificação, que demanda de investimentos em novas fontes. Neste contexto, a geração de energia nos oceanos é destacada. O primeiro ponto a respeito desta fonte é de que não há a necessidade de remoção da população na área de instalação, tal como os métodos de geração dentro do continente. O segundo principal ponto é a respeito da distribuição de energia. A maior parte da população mundial vive em regiões costeiras, diminuindo, portanto, a distância entre a produção e demanda, reduzindo assim, seus custos. As duas principais metodologias para se explorar a energia proveniente dos oceanos são: Energia de Ondas e Energia de Marés. E considerando que os ciclos de mare são governados principalmente pela interação gravitacional entre os oceanos, lua e sol, eles são facilmente previsíveis, o que aumenta a confiabilidade dos sistemas de geração de energia baseados em marés. Este trabalho explora as metodologias para analisar a geração de energia a partir de uma única turbina axial de corrente de maré através de uma metodologia baseada nas equações de Navier-Stokes com a média de Reynolds, analisadas em regime permanente. São discutidos efeitos da direção do escoamento, perfil de velocidades na entrada e nos níveis de turbulência. Os resultados são comparados com experimentos. É proposta uma metodologia alternativa para a modelagem da superfície livre com CFD uma vez que a metodologia atual é baseada em um escoamento bifásico que demanda de um refinamento adicional da malha e é computacionalmente caro. A nova metodologia usa uma parede elástica na região da superfície livre com a rigidez ajustada para se obter o mesmo efeito de restauração que a gravidade. De maneira geral, os resultados para o domínio aberto se aproximaram dos resultados experimentais, validando o modelo numérico e além disso, o modelo considerando confinamento da turbine mostrou maiores valores para os coeficientes de potência e empuxo, estando portanto, de acordo com a teoria do disco atuador. O modelo com a superfície livre elástica apresentou problemas de convergência, relacionados com números de Froude elevados, uma vez que isto se relaciona com maiores deformações na região da superfície livre. Uma simulação com 10% da velocidade original foi realizada, obtendo-se resultados coerentes para ambos coeficientes de potência e empuxo.

O objetivo desse trabalho é a construção de um sistema de geração de energia elétrica, para uso em locais remotos, tendo como fonte primária a energia proveniente de ondas marinhas. Numa primeira etapa foram realizados estudos e análises dos principais parâmetros significativos para a geração da energia elétrica e os dados de consumo de eletroeletrônicos. Este sistema serviu para coletar e armazenar dados que orientam o desenvolvimento de bombas e turbinas para a geração de energia elétrica. Foram também usados para avaliar o seu rendimento em diversas aplicações que necessitavam de energia elétrica. O uso da energia elétrica gerada também foi estudado para melhorar o seu rendimento diante dos vários equipamentos que foram utilizados desde notebooks até geladeiras convencionais. Foram empregados um microcontrolador, da família \"arduino\", vários sensores colocados em pontos estratégicos no local e os dados armazenados em memória durante o período do desenvolvimento. Sensores de pressão, vazão, amplitude das ondas, sentido do vento, temperatura e vários medidores (de tensão e corrente em AC e DC) foram usados para obter valores numéricos para análises de rendimentos de conversão em energia elétrica, vazão e outros parâmetros importantes para uma posterior melhoria no projeto inicial. Os dados foram armazenados em memórias do tipo cartão SD de 16 G bytes. Foi confeccionada uma bomba de água movida pelas ondas marinhas. Sua implantação ocorreu na Ilha do Arvoredo, em Guarujá, SP, onde a energia elétrica era gerada através do uso de motores a diesel. A água é bombeada a uma altura de 30 metros e armazenada em um tanque com capacidade de 20.000 litros. A água armazenada vai diretamente para uma turbina geradora de eletricidade por um sistema controlador de pressão e, pode gerar uma potência elétrica de até 200 W. O excedente de água poderá ser também usado para os viveiros de animais marinhos. A maior parte dos materiais que foram utilizados na fabricação dos equipamentos foi de materiais recicláveis reduzindo o custo do projeto. Esse projeto estará disponível para comunidades carentes que necessitam de energia elétrica em locais remotos, normalmente ilhas, mas podem ser adaptadas em terra desde que possuam quedas de água. O projeto de geração de energia usando ondas marinhas é inovador e com fins sociais para pessoas de baixa renda como os pescadores. Normalmente o pescado conseguido nas proximidades de ilhas isoladas são salgados para serem conservados devido à falta de refrigeração. / The aim of this work is the constructions of an electrical power generation system for use in remote locations, having primary source of energy from sea waves. At a first step were carried out studies and analyzes of the main important parameters for the generation of electricity and electronics power consumption data. This system was used to collect and store data that guide the development of pumps and turbines for generating electricity. Various electronics applications were also used to evaluate the total electricity was required and were studied to improve their performance like notebooks or conventional refrigerators. A microcontroller was employed and several sensors placed at strategic points in the power generation energy system and the data stored in the memory card during the development period. Pressure sensors, flow, amplitude of waves, wind direction, temperature and various electrical sensors (voltage and current in AC and DC) that were used to obtain numerical values for analysis of conversion into electrical energy, water flow and other important parameters for further improvement the initial project. The data were stored on SD memory card of 16 G bytes. A water pump driven by ocean sea waves was made. This work has taken place in Ilha do Arvoredo, in Guarujá, SP, where the electricity was generated using diesel engines. The water is pumped until 30 meters high and stored in a tank with 20.000 liters. This stored water goes directly to the turbine by a pressure system control and generate an electrical power output up to 200 W. When not require, the exceeding water can also be used for marine animals nurseries. Most materials that were used in manufacturing of the equipment is recyclable materials reducing the cost of the project. The final project will be available to poor communities that need electricity in remote locations. Usually the fish achieved near isolated islands are salted to be maintained for lack of refrigeration.

A tidal current turbine is a device functioning in a manner similar to wind turbine for harnessing energy from tidal currents, a group of which is called a farm. The existing approaches used to predict power from tidal current turbine farms oversimplify the hydrodynamic interactions between turbines, which significantly affects the results. The major focus of this dissertation is to study the relationship between turbine distribution (the relative position of the turbines) and the hydrodynamic interactions between turbines, and its impact on the power from a farm. A new formulation of the discrete vortex method (DVM-UBC) is proposed to describe the behavior of turbines and unsteady flow mathematically, and a numerical model is developed to predict the performance, the unsteady wake and acoustic emission of a stand-alone turbine using DVM-UBC. Good agreement is obtained between the results obtained with DVM-UBC and published numerical and experimental results. Then, another numerical model is developed to predict the performance, wake and acoustic emission of a two-turbine system using DVM-UBC. The results show that the power of a two-turbine system with optimal relative position is about 25% more than two times that of a stand-alone turbine under the same conditions. The torque such a system may fluctuate 50% less than that of a stand-alone turbine. The acoustic emission of such a system may be 35% less than that of a stand-alone turbine. As an extension, a numerical procedure is developed to estimate the efficiency of an N-turbine system by using a linear theory together with the two-turbine system model. By integrating above hydrodynamic models for predicting power and a newly-developed Operation and Maintenance (O&M) model for predicting the cost, a system model is framed to estimate the energy cost using a scenario-based cost-effectiveness analysis. This model can estimate the energy cost more accurately than the previous models because it breaks down turbine’s components and O&M strategies in much greater detail when studying the hydrodynamics and reliability of the turbine. This dissertation provides a design tool for farm planners, and shed light on other disciplines such as environmental sciences and oceanography. / Applied Science, Faculty of / Mechanical Engineering, Department of / Graduate

This research revolves around the concept design and theoretical validation of a new type of wave energy converter (WEC), comprising a pitching floater integrated with a resonant U-tank (RUT) and a Wells turbine as power take-off (PTO). Theoretical formulation of a fully coupled multi-body dynamic system, incorporating the thermodynamic processes of the RUT air chamber, its interaction with the PTO dynamics and their coupling with the floater is presented. Inaccuracies of the dynamic modeling of RUT based on Lloyd's low order model, which assumes constant hydrodynamic parameters irrespective of the frequency, are demonstrated by a series of high fidelity CFD simulations. These simulations are a systematic series of fully viscous turbulent simulations, using unsteady RANSE solvers, of the water sloshing at different frequencies of oscillation. Calibration of Lloyd’s model with CFD results evidenced that the RUT hydrodynamic parameters are not invariant to frequency. A numerical model was developed based on Simulink WEC-Sim libraries to solve the non-linear thermo-hydrodynamic equations of the device in time domain. For power assessment, parametric investigations are conducted by varying the main dimensions of the RUT and power RAOs were computed for each iteration. Performance in irregular sea state are assessed using a statistical approach with the assumption of linear wave theory. By superimposing spectrum energy density from two resource sites with RAO, mean annual energy production (MEAP) are computed. The predicted MEAP favorably compares with other existing devices, confirming the superior efficiency of the new proposed device over a larger range of incident wave frequency. / M.S. / This study present results of an investigation into a new type of wave energy converter which can be deployed in ocean and by its pitch response motion, it can harvest wave energy and convert it to electrical energy. This device consist of a floater, a U-tank (resonant U-tank) with sloshing water free to oscillate in response to the floater motion and a pneumatic turbine which produces power as air is forced to travel across it. The pneumatic turbine is used as the power take-off (PTO) device. A medium fidelity approach was taken to carry out this study by applying Lloyd’s model which describes the motion of the sloshing water in a resonant U-tank. Computational fluid dynamics (CFD) studies were carried out to calibrate the hydrodynamic parameters of the resonant U-tank as described by Lloyd and it was discovered that these parameters are frequency dependent, therefore Lloyd’s model was modelled to be frequency dependent. The mathematical formulation coupling the thermodynamic evolution of air in the resonant U-tank chamber, modified Lloyd’s sloshing water equation, floater dynamics and PTO were presented for the integrated system. These set of thermo-hydrodynamic equations were solved with a numerical model developed using MATLAB/Simulink WEC-Sim Libraries in time domain in other to capture the non-linearity arising from the coupled dynamics. To assess the annual energy productivity of the device, wave statistical data from two resource sites, Western Hawaii and Eel River were selected and used to carrying out computations on different iterations of the device by varying the tank’s main dimensions. This results were promising with the most performing device iteration yielding mean annual energy production of 579 MWh for Western Hawaii.

The huge natural energy resources available in the world’s oceans are attracting increasing commercial and political interest. In order to evaluate the status and the degree of acceptability of future Ocean Energy (OE) schemes, it was considered important to develop an Integrated Assessment Methodology (IAM) for ascertaining the relative merits of the competing OE devices being proposed. Initial studies included the gathering of information on the present status of development of the ocean energy systems on wave, OTEC and tidal schemes with the challenges faced for their commercial application. In order to develop the IAM, studies were undertaken for the development and standardization of the assessment tools focussing on: • Life Cycle Assessment (LCA) on emission characteristics. • Energy Accounting (EA) studies. • Environmental Impact Assessment (EIA) over different environmental issues. • Resource captures aspects. • Defining economy evaluation indices. The IAM developed from such studies comprised of four interrelated well defined tasks and six assessment tools. The tasks included the identification of the modus operandi on data collection to be followed (from industry) for assessing respective OE devices, and also advancing relevant guidelines as to the safety standards to be followed, for their deployment at suitable sites. The IAM as developed and validated from case studies in ascertaining relative merits of competing OE devices included: suitable site selection aspects with scope for resource utilisation capability, safety factors for survivability, scope for addressing global warming & energy accounting, the environmental impact assessment both qualitatively and quantitatively on different environmental issues, and the economic benefits achievable. Some of the new ideas and concepts which were also discovered during the development of the IAM, and considered useful to both industry and researchers are given below: • Relative Product Cost (RPC) ratio concept- introduced in making an economic evaluation. This is considered helpful in sensitivity analysis and making design improvements (hybridising etc) for the cost reduction of OE devices. This index thus helps in making feasibility studies on R&D efforts, where the capital cost requirement data and life span of the device is not well defined in the primary stages of development. • Determination of the threshold limit value of the barrage constant - considered useful in determining the efficacy of the planning process. The concept ascertained the relative efficiency achieved for various barrage proposals globally. It could also be applied to suggest the revisions required for certain barrage proposals and also found useful in predicting the basin area of undefined barrage proposal for achieving economic viability. • Estimations made on the future possibility of revenue earnings from the by-products of various OTEC types, including the scope of chemical hubs from grazing type OTEC plants. • Determination of breakeven point- on cost versus life span of wave and OTEC devices studied, which is useful in designing optimum life of the concerned devices. The above stated multi-criterion assessment methodology, IAM, was extended leading to the development of a single criterion model for ascertaining sustainability percent achievable from an OE device and termed IAMs. The IAMs was developed identifying 7 Sustainability Development Indices (SDI) using some the tools of the IAM. A sustainability scale of 0-100 was also developed, attributing a Sustainability Development Load Score (SDLS) percentage distribution pattern over each SDIs, depending on their relative importance in achieving sustainability. The total sum of sustainability development (SD) gained from each SDI gave the IAMs (for the concerned device), indicating the total sustainable percentage achieved. The above IAMs developed, could be applied in ranking OE devices alongside the unsustainable coal power station. A mathematical model of estimating the IAMs was formulated, in order to ascertain the viability to the sustainable development of any energy device. The instruments of IAM and IAMs which have been developed would be helpful to the OE industry in ascertaining the degree of acceptability of their product. In addition it would also provide guidelines for their safe deployment by assessing the relative merits of competing devices. Furthermore, IAM and IAMs would be helpful to researchers undertaking feasibility studies on R&D efforts for material development research, ‘hybridization studies’ (as also new innovations), cost reduction, the performance improvement of respective devices, and any economic gains. With future advancements in OE systems and the availability of field data from large scale commercial applications, the specific values/data of the IAM & IAMs may be refined, but the logic of the models developed in this research would remain the same.

Thesis (MBA)--Stellenbosch University, 2011. / Gaia Power is a South African start-up in the renewable energy industry. Among other products, they developed a wave energy converter, which is a device used to extract energy from ocean waves. This research deals with the economic feasibility study of the wave energy converter. Wave energy is a young field of research, especially in the South African context. Therefore sources for multiple angles of the project had to be found, analysed and brought into the Gaia Power context. Understanding the cost drivers of a wave energy plant was the foundation of the research itself. The Gaia Power specific levelised cost of electricity generation was calculated based on actual supplier quotes, reference costs found in the literature as well as assumptions. Still, such a calculation is actually more an estimation due to a high uncertainty level in all cost components. Especially the construction cost as well as the discount rate used have therefore been tested for sensitivity. Gaia Power‟s target production cost was R0.54 kWh, which equalled the Eskom tariff at the time of this research. Taking into account a R0.10/kWh fee payable to Eskom, the target cost sank to R0.44, which is about 25 percent lower than the minimum value for electricity generation cost found in the literature. This target was therefore expected to be and proved to be difficult to reach. The calculated levelised electricity cost was R0.99/kWh, with a possible range of R0.54/kWh to R1.60/kWh observed in the sensitivity analysis. These results show that the Gaia Power wave energy converter in the given specifications was not economically feasible. It was therefore recommended to rethink the specifications in order to reduce construction cost, which proved to be the largest cost driver. Besides the quantitative findings, this research also has a strong qualitative side. During the whole research it became obvious that there was an overall high risk level in the project due to the lack of experience with wave energy in general and in South Africa specifically, as well as the high impact of weather on the construction. Those risks were identified, analysed and recommended mitigation actions were derived.

The wave energy converter developed at Uppsala University consists of a linear generator at the seabed driven by the motion of a buoy on the water surface. The energy absorbed by the generator is negatively affected by variations of the mean sea level caused by tides, changes in barometric pressure, strong winds, and storm surges. The work presented in this doctoral thesis aims to investigate the losses in energy absorption for the present generation wave energy converter due to the effect of sea level variations, mainly caused by tides. This goal is achieved through the modeling of the interaction between the waves and the point absorber. An estimation of the economic cost that these losses imply is also made. Moreover, solutions on how to reduce the negative effect of sea level variations are discussed. To this end, two compensation systems which adjust the length of the connection line between the floater and the generator are designed, and the first prototype is built and tested near the Lysekil research site. The theoretical study assesses the energy loss at about 400 coastal points all over the world and for one generator design. The results highlight critical locations where the need for a compensation system appears compelling. The same hydro-mechanic model is applied to a specific site, the Wave Hub on the west coast of Cornwall, United Kingdom, where the energy loss is calculated to be about 53 %. The experimental work led to the construction of a buoy equipped with a screw jack together with its control, measurement and communication systems. The prototype, suitable for sea level variations of small range, is tested and its performance evaluated. A second prototype, suitable for high range variations, is also designed and is currently under construction. One main conclusion is that including the compensation systems in the design of the wave energy converter will increase the competitiveness of the technology from an economic point of view by decreasing its cost per kWh. The need for a cost-effective wave energy converter with increased survivability emphasizes the importance of the presented research and its future development.

This thesis aims to facilitate the siting and implementation of Florida Atlantic University Southeast National Marine Renewable Energy Center (FAU SNMREC) ocean current energy (OCE) projects offshore southeastern Florida through the analysis of benthic anchoring conditions. Specifically, a suitability analysis considering all presently available biologic and geologic datasets within the legal framework of OCE policy and regulation was done. OCE related literature sources were consulted to assign suitability levels to each dataset, ArcGIS interpolations generated seafloor substrate maps, and existing submarine cable pathways were considered for OCE power cables. The finalized suitability map highlights the eastern study area as most suitable for OCE siting due to its abundance of sand/sediment substrate, existing underwater cable route access, and minimal biologic presence. Higher resolution datasets are necessary to locate specific OCE development locales, better understand their benthic conditions, and minimize potentially negative OCE environmental impacts. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2014. / FAU Electronic Theses and Dissertations Collection

It has long been known from Thermodynamics and written in technical literature that, in principal, instant energy can be made available when dilute and concentrated solutions are mixed. For example, a river flowing into the sea carries with it a physical-chemical potential energy in its low salt content, some of which should be recoverable. As also known, a naturally occurring, diffusion-driven, spontaneous transport of ions occurs throughout a solution matrix, thru barrier interfaces, or thru ion-selective membranes from the side containing the salts of higher concentration to the compartments containing the more dilute solution to effect the equalization of concentration of the ionic species. Since this ion movement consists, preferentially, of either cations or anions, it leads to a charge separation and potential difference across the membrane, otherwise known as a membrane potential. Eventually, when the concentrations in the compartment are the same, the cell ceases to function. However, if operated as a fuel cell with its respective concentrations continually replenished, equilibrium at a specific value of potential difference is established. To capture the energy of this potentially significant albeit low power energy source, a suitable energy extraction device is required. The focus of this Ph.D. research effort is to address the concept, research and evaluation of a Bi-Polar membrane based seawater concentration cell and its suitability as a low power energy source for Energy Harvesting/MEMS devices (patent pending).

A wave energy converter has been constructed and its function and operational characteristics have been thoroughly investigated and published. The wave energy converter was installed in March of 2006 approximately two kilometers off the Swedish west coast in the proximity of the town Lysekil. Since then the converter has been submerged at the research site for over two and a half years and in operation during three time periods for a total of 12 months, the latest being during five months of 2008. Throughout this time the generated electricity has been transmitted to shore and operational data has been recorded. The wave energy converter and its connected electrical system has been continually upgraded and each of the three operational periods have investigated more advanced stages in the progression toward grid connection. The wave energy system has faced the challenges of the ocean and initial results and insights have been reached, most important being that the overall wave energy concept has been verified. Experiments have shown that slowly varying power generation from ocean waves is possible. Apart from the wave energy converter, three shorter studies have been performed. A sensor was designed for measuring the air gap width of the linear generator used in the wave energy converter. The sensor consists of an etched coil, a search coil, that functions passively through induction. Theory and experiment showed good agreement. The Swedish west coast wave climate has been studied in detail. The study used eight years of wave data from 13 sites in the Skagerrak and Kattegatt, and data from a wave measurement buoy located at the wave energy research site. The study resulted in scatter diagrams, hundred year extreme wave estimations, and a mapping of the energy flux in the area. The average energy flux was found to be approximately 5.2 kW/m in the offshore Skagerrak, 2.8 kW/m in the near shore Skagerrak, and 2.4 kW/m in the Kattegat. A method for evaluating renewable energy technologies in terms of economy and engineering solutions has been investigated. The match between the technologies and the fundamental physics of renewable energy sources can be given in terms of the technology’s utilization. It is argued that engineers should strive for a high utilization if competitive technologies are to be developed.