Thickened tailings production and disposal continue to grow in importance in the mining industry. In particular, the transport of oil sands tailings is of interest in this study. These tailings must be in a homogeneous state (non-segregating) during pipeline flow and subsequent discharge. Tailings are often transported in an open channel or flume. Slurries containing both clay and coarse sand particles typically exhibit non-Newtonian rheological behaviour. The prediction of the flow behaviour of these slurries is complicated by the limited research activity in this area. As a result, the underlying mechanisms of solids transport in these slurries are not well understood. To address this deficiency, experimental studies were conducted with kaolin clay slurries containing coarse sand in an open circular channel.<p> A numerical model has been developed to predict the behaviour of coarse solid particles in laminar, open channel, non-Newtonian flows. The model involves the simultaneous solution of the Navier-Stokes equations and a scalar concentration equation describing the behaviour of coarse particles within the flow. The model uses the theory of shear-induced particle diffusion (Phillips et al., 1992) to provide a number of relationships to describe the diffusive flux of coarse particles within laminar flows. A sedimentation flux has been developed and incorporated into the Phillips et al. (1992) model to account for gravitational flux of particles within the flow. Previous researchers (Gillies et al., 1999) have shown that this is a significant mechanism of particle migration.<p> The momentum and concentration partial differential equations have been solved numerically by applying the finite volume method. The differential equations are non-linear, stiff and tightly coupled which requires a novel means of analysis. Specific no-flux, no-slip and no-shear boundary conditions have been applied to the channel walls and free surface to produce simulated velocity and concentration distributions. The results show that the model is capable of predicting coarse particle settling in laminar, non-Newtonian, open channel flows. The results of the numerical simulations have been compared to the experimental results obtained in this study, as well as the experimental results of previous studies in the literature.

Thickened tailings production and disposal continue to grow in importance in the mining industry. In particular, the transport of oil sands tailings is of interest in this study. These tailings must be in a homogeneous state (non-segregating) during pipeline flow and subsequent discharge. Tailings are often transported in an open channel or flume. Slurries containing both clay and coarse sand particles typically exhibit non-Newtonian rheological behaviour. The prediction of the flow behaviour of these slurries is complicated by the limited research activity in this area. As a result, the underlying mechanisms of solids transport in these slurries are not well understood. To address this deficiency, experimental studies were conducted with kaolin clay slurries containing coarse sand in an open circular channel.<p> A numerical model has been developed to predict the behaviour of coarse solid particles in laminar, open channel, non-Newtonian flows. The model involves the simultaneous solution of the Navier-Stokes equations and a scalar concentration equation describing the behaviour of coarse particles within the flow. The model uses the theory of shear-induced particle diffusion (Phillips et al., 1992) to provide a number of relationships to describe the diffusive flux of coarse particles within laminar flows. A sedimentation flux has been developed and incorporated into the Phillips et al. (1992) model to account for gravitational flux of particles within the flow. Previous researchers (Gillies et al., 1999) have shown that this is a significant mechanism of particle migration.<p> The momentum and concentration partial differential equations have been solved numerically by applying the finite volume method. The differential equations are non-linear, stiff and tightly coupled which requires a novel means of analysis. Specific no-flux, no-slip and no-shear boundary conditions have been applied to the channel walls and free surface to produce simulated velocity and concentration distributions. The results show that the model is capable of predicting coarse particle settling in laminar, non-Newtonian, open channel flows. The results of the numerical simulations have been compared to the experimental results obtained in this study, as well as the experimental results of previous studies in the literature.

Η παρούσα Διατριβή Μεταπτυχιακού Διπλώματος Ειδίκευσης, πραγματεύεται την ανάλυση της τυρβώδους ροής σε ανοικτούς αγωγούς στον πυθμένα των οποίων ενυπάρχουν σχηματισμοί μορφής θινών (dunes). Μελετήθηκε η περίπτωση 5 θινών οι οποίες τοποθετήθηκαν στον πυθμένα ενός καναλιού βάθους d θεωρώντας μόνιμη ροή. Για την επίλυση χρησιμοποιήθηκαν οι εξισώσεις RANS, ενώ για το κλείσιμο της τύρβης χρησιμοποιήθηκαν τα μοντέλα μιας εξίσωσης Spalart-Allmaras και δύο εξισώσεων k-ε. Η διαχείριση της ελεύθερης επιφάνειας έγινε με την μέθοδο VOF, ενώ η αριθμητική επίλυση βασίστηκε στην μέθοδο των πεπερασμένων όγκων και πραγματοποιήθηκε με τον εμπορικό κώδικα FLUENT 6.1.2. Για την ροή στον ανοικτό αγωγό, στον πυθμένα του οποίου ενυπήρχαν οι σχηματισμοί, θεωρήθηκε αριθμός Reynolds , κλίση πυθμένα και συντελεστή Manning , ο οποίος αντιστοιχεί σε ισοδύναμο ύψος τραχύτητας τοιχωμάτων . Προκειμένου να επαληθευθεί η ακρίβεια της αριθμητικής μεθόδου, επιλύθηκε η περίπτωση του επίπεδου πυθμένα και τα αποτελέσματα συγκρίθηκαν με γνωστά πειραματικά αποτελέσματα καθώς και αποτελέσματα τα οποία προέκυψαν από την μονοδιάστατη ανάλυση της ροής πάνω από επίπεδο πυθμένα. Τα αποτελέσματα βρέθηκαν σε καλή συμφωνία, κυρίως για την κατανομή της ταχύτητας, ενώ για την τύρβη υπήρχε πολύ καλή συμφωνία κυρίως πλησίον του πυθμένα. Για το πρόβλημα των θινών εξετάσθηκαν: (α) τρεις περιπτώσεις με σταθερό άνοιγμα θίνης προς βάθος ροής και διαφορετικά ύψη θινών , 0.25 και (β) τρεις περιπτώσεις με σταθερή αναλογία ανοίγματος προς ύψος και ύψη θινών όπως στην περίπτωση (α). Η ανάλυση έδειξε ότι το μέσο προφίλ της ελεύθερης επιφάνειας μειώνεται στην διεύθυνση της ροής, ενώ πάνω από κάθε θίνη το πλάτος της ανύψωσης της ελεύθερης επιφάνειας αυξάνει με την αύξηση του ύψους και του ανοίγματος των θινών. Η κατανομή των διατμητικών τάσεων παρουσιάζει κυματοειδή μορφή υπεράνω των θινών και αυξάνει αυξανομένου του ύψους τους και με την μείωση του ανοίγματός τους. Πίσω από κάθε θίνη δημιουργείται θύλακας ανακυκλοφορίας της ροής και ο λόγος της απόστασης του σημείου επανακόλλησης προς το ύψος της θίνης είναι . / The spatial development of the turbulent open channel flow over bottom with five dunes is studied. The steady-state flow is described by the RANS equations utilizing either the or the Spalart-Allmaras turbulence models. The free-surface treatment is based on the VOF formulation, while the numerical solution is based on a finite-volume, unstructured-grid discretization. Lengths are rendered dimensionless by the inflow channel depth, while velocities by the mean inflow velocity. The inflow Reynolds number is , the channel slope is and the Manning coefficient is , which results to a roughness height . In order to verify the numerical methods, the flat bottom case is considered and the numerical predictions are compared to known experimental data. We get very good agreement for the velocity distributions, while for turbulence the results are very good close to the bottom and poor close to the free surface. Then, we consider: (a) three cases with constant dune length and differing dune heights 0.15, 0.25, 0.35, and (b) three cases with constant ratio and dune heights as in (a). The spatial development of the free-surface elevation over the dunes presents a negative mean slope for all cases. Locally over each dune, the amplitude of the free-surface elevation increases with increasing dune height and increasing dune length. The spatial development of the wall shear stress presents a wave-like behavior and its amplitude increases with increasing dune height and decreasing dune length. On every dune crest the streamwise velocity profile is steeper than the universal logarithmic profile similar to the behavior in a favorable pressure gradient boundary layer. The detachment at each dune crest is followed by a recirculation region and reattachment at a distance from the dune trough.

Vegetation is commonly modelled as emergent arrays of rigid, circular cylinders. However, the drag coefficient (CD) of real stems or trunks is closer to that of cylinders with a square cross-section. In this thesis, vegetation has been idealised as square cylinders in laboratory experiments with a turbulence intensity of the order of 10% which is similar to that of typical river flows. These cylinders may also represent other obstacles such as architectural structures. This research has determined CD of an isolated cylinder and cylinder pairs as a function of position as well as the average drag coefficient (CDv) of larger arrays. A strain gauge was used to measure CD whilst CDv was computed with a momentum balance which was validated by strain gauge measurements for a regularly spaced array. The velocity and turbulence intensity surrounding a pair of cylinders arranged one behind the other with respect to mean flow (in tandem) were also measured with an Acoustic Doppler Velocimeter. The isolated cylinder CD was found to be 2.11 in close agreement with other researchers. Under fixed flow conditions CD for a cylinder in a pair was found to be as low as -0.40 and as high as 3.46 depending on their relative positioning. For arrays, CDv was influenced more by the distribution of cylinders than the flow conditions over the range of conditions tested. Mean values of CDv for each array were found to be between 1.52 and 3.06. This new insight therefore suggests that CDv for vegetation in bulk may actually be much higher than the typical value of 1 which is often assumed to apply in practice. If little other information is available, a crude estimate of CDv = 2 would be reasonable for many practical applications. The validity of a 2D realizable k-epsilon turbulence model for predicting the flow around square cylinders was evaluated. The model was successful in predicting CD for an isolated cylinder. In this regard the model performed as well as Large Eddy Simulations by other authors with a significant increase in computational efficiency. However, the numerical model underestimates CD of downstream cylinders in tandem pairs and overestimates velocities in their wake. This suggests it may be necessary to expand the model to three-dimensions when attempting to simulate the flow around two or more bluff obstacles with sharp edges.

It is important for practical and legal reasons that water and sediments in disturbed areas around the mining operation should be controlled. The construction of a well-designed drainage system that controls erosion and thus restores the proper hydraulic function of the surface is one of the most important post-disturbance features which should be done as part of the mining activities. However, even with the best planning and design, unless proper construction practices are adapted; both the disturbed and reclaimed areas are very much likely to be susceptible to erosion, sedimentation and stability problems. In order to tackle the problem, guidelines on how to design and construct the drainage system should be well prepared. The main objective of this study was to prepare guidelines for the proper design, construction and monitoring of the water drainage management system in the study areas (Kankberg, Maurliden and Renström-Petiknäs). This report has analysed the results from the outcome of HEC-RAS software for the case study of the new ditch around the Maurliden mine site and integrated with different guidelines. Based on the results of the HEC-RAS, the most common problems in the drainage system have been identified. Moreover the thesis project identified important physical parameters such as cross-sections and slopes of the representative ditch which affect the function of the ditch in the study areas. Hydraulic parameters such as velocity which is very important for designing the type of lining and also Froude number which is very important in identifying the type of flow whether it is super-critical, critical or sub-critical were identified. The latter helps to select the type of guideline to be used between steep slope and mild slope.

<p>We study the effect of minute perturbations by using blowing jets at upstream and bio-inspired micro denticles on turbulence large-scale motions which are observed to be crucial in controlling heat transfer, noise and drag reduction. This work is divided into two phases. In first phase, we studied the effect of blowing perturbations at upstream on large-scale motions and associated co?herent vortical structures which are crucial in enhancing heat transfer by promoting mixing. The second phase is focused on impact of flow dynamics in preventing the biofouling using micro bioinspired structures and the importance of flow regime in designing the antifouling coating us?ing bioinspired structures is demonstrated, and subsequently, separation bubble dynamics and its characterization is carried out for a transonic channel imposed with pressure gradient to further expand our thesis outcomes to utilize micro bioinspired structures in aerospace applications, noise reduction, and to delay separation.</p> <p><br></p> <p>Extensive studies were focused on the importance of large-scale motions (LSM) and their con?tribution to TKE and turbulence mixing. Although there are studies focusing on the λ2 coherent vortical structures and large-scale motions separately, there are no studies addressing the control?ling using upstream perturbations on the large-scale motions and their associated λ2 vortices. In the first phase of our studies, we used the DNS data of channel flow for Reτ = 394 generated using in-house code. In these simulations, we created blowing perturbations using spanwise jets of low blowing ratio, 0.2, placed at upstream. The spatial large-scale motions are extracted using a a novel 3D adaptive Gaussian filtering technique developed based on Lee and Sung [1] for turbulent pipe flows. POD is used to extract the energetic large-scale motions and coherent vortical structures are extracted using λ2-criterion for its efficiency in educing coherent structures in cross flow jets. The results show that the upstream perturbations enhance streamwise heat flux via energetic LSM and also create a secondary peak of scalar production in the log-layer showing that the perturbations alter LSMs to enhance the heat transfer. Filtered large-scale field from Gaussian filtering technique have an integral length scale greater than 2h (where h is channel half-height) are used to obtain λ2 vortices. The resulted λ2 vortices are of ring-type and have higher signature of temperature than their counterpart. The pre-multiplied spectra shows that the upstream perturbations can excite the large-scale wave-numbers which are in the same order as the jet diameter and spacing between them. Simulations show the presence of secondary peak in the log-layer and increased turbulence production which are eminent of large-scales. Furthermore, our results suggest that jet spacing and diameter are crucial in exciting large-scale field to control turbulent flows.</p> <p><br></p> <p>Evans, Hamed, Gorumlu, et al. [2] modeled the denticles present on Mako shark skin into a diverging micro-pillars. They conducted experimental studies in a water tunnel using these on the back of airfoil exposed to an adverse pressure gradient flow. They observed that presence of these pillars reduced the re-circulation bubble (form drag) by 50%. They proposed a blowing and suction type mechanism by which the micro pillars interact with the boundary layer. However, the details of underlying interfacial mechanism is not completely understood. The unique impact of flow conditions on anti-biofouling and the corresponding mechanisms for the first time is illustrated. We employed commercially available bioinspired structures as micro-diverging pillars making it feasible to apply in real life. We demonstrated the underlying mechanism by which bio?inspired structures are responsible for anti-biofouling. To study the pressure gradient effects on the separation under transonic conditions, we performed direct numerical simulations (DNS) in a non?equilibrium flow created by a sinsuoidal contraction and also, we quantified the separation length,</p> <p>detachment, and attachment points of separation bubble imposed with various pressure gradients and their variation in the transonic and subsonic regimes. We noticed that the resultant shear at the attachement led to the enhancement of coherent structures which are extended into the outer layer under transonic flow which is quite different than the subsonic flow.</p>

Tidal bores are surge waves propagating upstream rivers as the tide rushes into estuaries. They induce large turbulences and mixing of the river and estuary flow of which effects remain scarcely studied. Herein, tidal bores are investigated experimentally and numerically with an idealised model of positive surges propagating upstream an initially steady flow. The experimental work estimated flow changes and typical turbulent length scale evolution induced by undular bores with and without breaking roller. The bore passage was associated with large free surface and flow velocity fluctuations, together with some variations of the integral turbulent scales. Coherent turbulent structures appeared in the wake of leading wave near the bed and moved upward into the water column during the bore propagation. The numerical simulations were based on previous experimental work on undular bores. Some test cases were realised to verify the accuracy of the numerical methods. The results gave access to the detailed flow evolution during the bore propagation. Large velocity reversals were observed close to the no-slip boundaries. In some configurations, coherent turbulent structures appeared against the walls in the wake of the bore front.

Un mascaret est une vague remontant contre le courant d’un fleuve lorsque la marée se propage dans un estuaire. À son passage, le mascaret induit une forte turbulence et un fort mélange dont les effets sur la vie de l’estuaire sont encore mal quantifiés. Ici, le phénomène est étudié expérimentalement et numériquement en utilisant un modèle d’onde positive se propageant contre un courant permanent.L’étude en laboratoire a permis de mesurer les variations de la surface libre, de la vitesse de l’écoulement ainsi que des échelles de turbulence. Lors de son passage, des fluctuations importantes de la surface libre et de la vitesse de l’écoulement sont observées, ainsi que des variations des échelles de turbulences. Des structures turbulentes semblent se former près du fond sous le front de l’onde et montent dans la colonne d’eau après le passage du front.La simulation numérique fut réalisée à partir de données expérimentales d’onde positive ondulée sur fond lisse. Une validation des méthodes numériques a été réalisée pour différente configuration. Les résultats des simulations d’onde positives donnent une cartographie détaillée de l’écoulement dans tout le canal. De plus, la simulation a permis d’identifier une inversion de la vitesse près des parois lors du passage des crêtes des ondes générant dans certaines configurations des structures turbulentes. / Tidal bores are surge waves propagating upstream rivers as the tide rushes into estuaries. They induce large turbulences and mixing of the river and estuary flow of which effects remain scarcely studied. Herein, tidal bores are investigated experimentally and numerically with an idealised model of positive surges propagating upstream an initially steady flow. The experimental work estimated flow changes and typical turbulent length scale evolution induced by undular bores with and without breaking roller. The bore passage was associated with large free surface and flow velocity fluctuations, together with some variations of the integral turbulent scales. Coherent turbulent structures appeared in the wake of leading wave near the bed and moved upward into the water column during the bore propagation. The numerical simulations were based on previous experimental work on undular bores. Some test cases were realised to verify the accuracy of the numerical methods. The results gave access to the detailed flow evolution during the bore propagation. Large velocity reversals were observed close to the no-slip boundaries. In some configurations, coherent turbulent structures appeared against the walls in the wake of the bore front.